T型分子筛膜的合成、表征与渗透汽化性能

采用二次生长法,在不锈钢、α-Al₂O₃和莫来石多孔管状支撑体上分别合成了高渗透汽化性能的T型分子筛膜。考察了合成条件如合成时间、n(SiO₂)/n(Al₂O₃)、n(H₂O)/n(Al₂O₃)和硅源等对T型分子筛膜形成和分离性能的影响。通过XRD和SEM表征了膜的晶相和形貌。     

类固相法快速合成高钙镁离子交换性能的P型分子筛

以硅铝干凝胶为硅源和铝源,氢氧化钠为碱源,采用类固相法快速合成了P型分子筛,并通过X射线衍射（XRD）、扫描电镜（SEM）等手段对产品进行了表征分析。结果表明,硅铝干凝胶的组成n_SiO2/n_Al2O3=5,晶化时间和晶化温度分别为3 h、140℃,原料的组成n_Na2O/n_SiO2、n_H2O/n_SiO2=18.51时,可制备形貌均一、结晶良好的P型分子筛产品。与传统水热法相比,该方法极大地减少了合成过程的用水量,缩短了晶化时间,提高了产品的钙镁离子交换性能,从整体上优化了P型分子筛的合成工艺。     

"一步法"合成多级孔SAPO-34分子筛

以TPOAC和硅溶胶为硅源,合成了多级孔SAPO-34分子筛,总比表面积达到649 m²·g^-1。详细考察了TPOAC和硅溶胶的配比对多级孔SAPO-34外比表面的影响,通过XRD、BET、SEM、NH₃-TPD等对其结构进行表征,结果表明多级孔SAPO-34的外比表面积可调变,晶体外观有较多缺陷位置,弱酸量减少,强酸位有变弱的趋势。在TPOAC与硅溶胶的投料比为3:2,晶化时间为10 d,投料比为n_Al2O3:n_P2O5:n_Si:n_TEAOH:n_H2O=1:0.9:0.5:2:60时,合成的多级孔SAPO-34的外比表面积达到最大,为100 m²·g^-1。     

EU-1分子筛的合成及其在正己烷异构化反应中的催化性能

在不同硅铝比(n_SiO2/n_Al2O3)的合成凝胶(含纯硅凝胶)中引入晶种,合成了纯相的EU-1分子筛。研究了铝源、模板剂和晶种添加量对EU-1分子筛的结晶度、形貌尺寸等的影响;重点研究了不同硅铝比对样品结晶度、晶粒尺寸、酸性、比表面积和孔容等的影响。将合成结果绘制成了纯相EU-1分子筛的合成条件三元图,从三元图可看出,晶种法可显著扩大纯相EU-1分子筛的合成区域。将Pt/H-EU-1用于正己烷异构化反应,结果表明,该催化剂具有优异的正己烷异构化活性及稳定性,对异构烷烃有较高的选择性。     

离子热法合成多级孔CuAPO-5分子筛

采用丁二酸、氯化胆碱与四乙基溴化铵三元低共熔体为溶剂和模板剂,借助微波辐射快速合成了具有多级孔结构的CuAPO-5分子筛.系统地考察了P₂O₅/Al₂O₃、HF/Al₂O₃与CuO/Al₂O₃的物质量之比,铝源及铜源对CuAPO-5分子筛合成的影响.利用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)和N₂物理吸脱附等检测手段对合成产物的结晶度、形貌和孔结构等进行了表征.通过SEM可知在一定的条件下,可得到具有六角纳米盘状特殊形貌的CuAPO-5分子筛.N₂物理吸脱附、SEM和TEM分析表明该分子筛是一种同时存在微孔和介孔的多级孔磷酸铝分子筛材料.     

清液体系中T型分子筛膜的高重复性合成与渗透汽化性能

以自制微米级分子筛为晶种,在清液体系中成功合成出高性能的T型分子筛膜,考察了硅铝比、水硅比、碱度及合成温度与时间等条件对膜的生长和渗透汽化性能的影响.结果表明,在摩尔组成为1SiO₂:0.015Al₂O₃:0.41(Na₂O+K₂O):30H₂O的清液体系中,于423K晶化6h的条件下可较快地形成一层厚度为5μm的连续致密纯相T型分子筛膜,较大缩短了膜合成时间且提高了膜致密性.在优化条件下所合成的膜具有优良的分离性能和高重复性.348K时,在10wt%水-90wt%异丙醇混合物体系中膜的渗透通量和分离因子分别高达4.20kg/(m²·h)和7800.     

变浓度无有机模板剂合成ZSM-5沸石分子筛膜

报道了无有机模板剂制备出15 nm的ZSM-5分子筛，并以其为晶种浸涂在多孔α-Al₂O₃陶瓷管外表面，再用先浓后稀的无有机模板剂的晶化液水热合成出ZSM-5分子筛膜的新方法。晶种和晶化液的物质的量组成为12Na₂O∶100SiO₂∶2Al₂O₃∶(2 500～5 000)H₂O。XRD分析表明α-Al₂O₃陶     

无有机模板剂水热合成Co同晶取代的丝光沸石分子筛

在硅酸钠、硫酸铝、硝酸钴和氢氧化钠的全无机体系条件下, 采用无有机模板剂水热法合成了Co同晶取代的丝光沸石分子筛. 通过粉末X射线衍射(XRD)、扫描电子显微镜(SEM)、电感耦合等离子体(ICP)光谱、氮气吸附、紫外-可见(UV-Vis)光谱、热重(TG)分析等手段对所得固体产物的织构性质以及钴在分子筛中的存在状态进行了表征. 结果表明, 该方法成功地将Co离子引入到丝光沸石分子筛的骨架结构中, 未发现骨架外Co物种. 典型的合成条件为n(Co)/n(SiO₂) =0.01-0.04, n(SiO₂)/n(Al₂O₃) =20-50, n(H₂O)/n(SiO₂) =40, n(Na₂O)/n(SiO₂)=0.4, 晶化温度170 °C, 晶化时间3-7 d. 讨论了Na+离子在无有机模板剂合成中的结构导向作用. 全无机体系合成得到的产物无需进行传统的高温煅烧处理, 即可获得开放的微孔孔道, 实现了低成本、低能耗、环境友好的Co-丝光沸石的合成.     

氧化物和沸石载体上负载KNO3的分解

本文报道采用程序升温分解-比色(TPDE-CM)的新方法研究了KNO₃在Al₂O₃、 TiO₂、 SiO₂等氧化物和NaY、 KY、 Kβ等沸石及MCM-41中孔分子筛上的分解,首次发现负载的KNO₃由于受到载体表面的作用而能在400～500 K开始分解;而分散在Al₂O₃上的KNO₃甚至于在室温下就可被部分分解。     

间歇式水热合成制备丝光沸石膜及其异丙醇脱水应用

采用市售廉价大孔α-Al₂O₃管作为基质材料，通过热浸渍法在管外表面涂敷晶种，随后在无模板剂体系下，利用新型的间歇式水热合成法制备丝光沸石膜。对比了传统加热和间歇式加热对丝光沸石膜形貌、结构及渗透蒸发异丙醇脱水分离性能的差异。考察了合成液中Na₂O/SiO₂、SiO₂/Al₂O₃和NaF/SiO₂物质的量之比在间歇式水热合成下对丝光沸石膜的影响。研究结果表明，当合成液中Na₂O/SiO₂、SiO₂/Al₂O₃和NaF/SiO₂物质的量之比分别为0.24、16.7和0.25时，制备的丝光沸石膜渗透蒸发异丙醇脱水分离性能最佳，在75℃下，对异丙醇/水(9∶1，w/w)的渗透通量达5.60 kg·m^-2·h^-1，水对异丙醇的分离因数大于10 000。     

Synthesis and structure of hydroxyisoxazolidines and derivatives of hydroxylamine and alkenals

The reactions of N-substituted hydroxylamines with alkenals serve as a method for the synthesis of the corresponding 2-substituted 3(5)-hydroxyisoxazolidines. The reaction pathway is determined by the nature of the substituent attached to the nitrogen atom. Ring-chain isomerism has been detected in these newly obtained compoundsTranslated from Khimiya Geterotsiklicheskikh Soedinenii, No. 9, pp. 1270–1276, September, 1987.     

Synthesis and characterization of triazenide and triazene complexes of ruthenium and osmium

Triazenide [M(eta2-1,3-ArNNNAr)P4]BPh4 [M = Ru, Os; Ar = Ph, p-tolyl; P = P(OMe)3, P(OEt)3, PPh(OEt)2] complexes were prepared by allowing triflate [M(kappa2-OTf)P4]OTf species to react first with 1,3-ArN=NN(H)Ar triazene and then with an excess of triethylamine. Alternatively, ruthenium triazenide [Ru(eta2-1,3-ArNNNAr)P4]BPh4 derivatives were obtained by reacting hydride [RuH(eta2-H2)P4]+ and RuH(kappa1-OTf)P4 compounds with 1,3-diaryltriazene. The complexes were characterized by spectroscopy and X-ray crystallography of the [Ru(eta2-1,3-PhNNNPh){P(OEt)3}4]BPh4 derivative. Hydride triazene [OsH(eta1-1,3-ArN=NN(H)Ar)P4]BPh4 [P = P(OEt)3, PPh(OEt)2; Ar = Ph, p-tolyl] and [RuH{eta1-1,3-p-tolyl-N=NN(H)-p-tolyl}{PPh(OEt)2}4]BPh4 derivatives were prepared by allowing kappa1-triflate MH(kappa1-OTf)P4 to react with 1,3-diaryltriazene. The [Os(kappa1-OTf){eta1-1,3-PhN=NN(H)Ph}{P(OEt)3}4]BPh4 intermediate was also obtained. Variable-temperature NMR studies were carried out using 15N-labeled triazene complexes prepared from the 1,3-Ph15N=N15N(H)Ph ligand. Osmium dihydrogen [OsH(eta2-H2)P4]BPh4 complexes [P = P(OEt)3, PPh(OEt)2] react with 1,3-ArN=NN(H)Ar triazene to give the hydride-diazene [OsH(ArN=NH)P4]BPh4 derivatives. The X-ray crystal structure determination of the [OsH(PhN=NH){PPh(OEt)2}4]BPh4 complex is reported. A reaction path to explain the formation of the diazene complexes is also reported.     

Investigation of adhesion and mobility of polyurethane and epoxy-rubber glues and adhesives

The values of activation parameters in uncured and cured epoxy resins, rubbers, and blends thereof are investigated. The dependences of activation energy and adhesion strength of epoxy-rubber compositions on rubber content are determined. The correlation of adhesion and activation energy values for polyurethane rubber and epoxy-rubber compositions is shown.     

Mass and NMR spectra of haplophyllidine and perforine and of their derivatives

Conclusions The mass and NMR spectra of haplophyllidine, perforine, and their derivatives have been studied. The influence of the open and cyclic forms of the molecular ion on the nature of the fragmentation has been discussed. The main routes of fragmentation of the compounds considered are due to the presence of substituents at C₈ and C₄.Khimiya Prirodnykh Soedinenii, Vol. 5, No. 4, pp. 273–279, 1969     

Crystal and molecular structure of aroyl- and acetylhydrazones of acet- and benzaldehydes

Aroyl- and acetylhydrazones of acet- (I) and benzaldehydes (IV) and benzoylhydrazones of acet- (II) and benzaldehydes (III) were studied by x-ray structural and quantum-chemical methods in order to establish their structures. Compund (I) was the EEZ structure in the crystal. Calculations and spectral data showed that the EEE form occurs in nonpolar solvents and in the gas phase. According to crystallographic data molecules (I)–(IV) are the E-isomers (relative to the N-N bond) and the hydrazone fragments are planar. Intermolecular N-H...O H-bonds from in the crystals. The data obtained suggest that the majority of acylhydrazones are conformationally rigid on dissolution although exceptions do occur. Apparently the reasons for the difference of acetyl- and benzoylhydrazones in electrocarboxylation reactions are electronic and not steric factors.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 1, pp. 75–81, January, 1991.     

Glycolate and Thioglycolate Complexes of Rhenium and Their Oxidative Elimination of Ethylene and of Glycol

Selenium dioxide and osmium tetroxide are effective reagents and catalysts for olefin oxidation, although, owing to their toxicity, reservations remain as to their applicability.^[1] We are therefore seeking more easily handled metal oxides that are soluble in organic solvents and that are as effective as osmium tetroxide in carrying out stereospecific cis hydroxylation of olefins. The rhenium(VII ) oxide 1 , which has meanwhile become readily accessible, is a favorable candidate.^[2]     

Preparation and characterization of diarylphosphazene and diarylphosphinohydrazide complexes of titanium, tungsten and ruthenium and phosphorylketimido complexes of rhenium

Reaction of the proligand Ph2PN(SiMe3)2 (L1) with WCl6 gives the oligomeric phosphazene complex [WCl4(NPPh2)]n, 1 and subsequent reaction with PMe2Ph or NBu4Cl gives [WCl4(NPPh2)(PMe2Ph)] (2) or [WCl5(NPPh2)][NBu4] (3), respectively. DF calculations on [WCl5(NPPh2)][NBu4] show a W=N double bond (1.756 A) and a P-N bond distance of 1.701 A, which combined with the geometry about the P atom suggests, there is no P-N multiple bonding. Reaction of L1 with [ReOX3(PPh3)2] in MeCN (X = Cl or Br) gives [ReX2(NC(CH3)P(O)Ph2)(MeCN)(PPh3)](X = Cl, 4, X = Br, 5) which contains the new phosphorylketimido ligand. It is bound to the rhenium centre with a virtually linear Re-N-C arrangement (Re-N-C angle = 176.6 degrees, when X = Cl) and there is multiple bonding between Re and N (Re-N = 1.809(7) A when X = Cl). The proligand Ph2PNHNMe2(L2H) reacts with [(C5H5)TiCl3] to give [(C5H5)TiCl2(Me2NNPPh2)] (6). An X-ray crystal structure of the complex shows the ligand (L2) is bound by both nitrogen atoms. Reaction of the proligands Ph2PNHNR2[R2 = Me2 (L2H), -(CH2CH2)2NCH3 (L3H), (CH2CH2)2CH2 (L4H)] with [{RuCl(mu-Cl)(eta6-p-MeC6H4iPr)}2] gave [RuCl2(eta6-p-MeC6H4iPr)L] {L = L2H (7), L3H (8), L4H (9)}. The X-ray crystal structures of 7-9 confirmed that the phosphinohydrazine ligand is neutral and bound via the phosphorus only. Reaction of complexes 7-9 with AgBF4 resulted in chloride ion abstraction and the formation of the cationic species [RuCl(6-p-MeC6H4iPr)(L)]+ BF4- {(L = L2H (10), L3H (11), L4H (12)}. Finally, reaction of complex 6 with [{RuCl(mu-Cl)(eta6-p-MeC6H4iPr)}2] gave the binuclear species [(eta6-p-MeC6H4iPr)Cl2Ru(mu2,eta3-Ph2PNNMe2)TiCl2(C5H5)], 13.