CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基体表面制备一层TiO₂纳米管阵列薄膜, 然后通过水热反应在TiO₂纳米管上负载CdS纳米粒子, 形成CdS/TiO₂纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO₂纳米管的光电性能和光催化活性, 结果表明, 相比于TiO₂纳米管, CdS/TiO₂纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

部分还原氧化石墨烯/二氧化钛复合材料的水热合成及其光催化活性

采用水热法以Hummers氧化法制备的氧化石墨和钛酸四丁酯为原料制备了部分还原的氧化石墨烯/二氧化钛(RGO/TiO₂)复合光催化剂, 并研究了该复合材料在可见光以及紫外光下对亚甲基蓝的光催化降解活性.结果表明, 通过改变反应温度和氧化石墨加入量可以调控TiO₂的晶相组成及其在复合材料中的分散性; 在水热反应过程中氧化石墨烯发生了部分还原; 所制备的RGO/TiO₂复合材料的可见光和紫外光催化活性均高于纯TiO₂; 部分还原的氧化石墨烯在复合材料中担当载体和电子受体, 同时可以使TiO₂的初始吸收边向可见光区域红移, 增强了TiO₂在可见光区域的吸收, 能有效提高对目标污染物的吸附性和光催化降解活性.     

纳米TiO2固相光催化降解固体废弃塑料

以纳米TiO₂作光催化剂,制备出环境友好的可光催化降解的纳米复合塑料是解决“白色污染”行之有效的方法之一。本文综述了近年来纳米TiO₂固相光催化降解固体废弃塑料的研究进展,探讨了TiO₂-聚合物复合膜的固相光催化反应机理及光催化降解情况,从对纳米TiO₂表面改性以改善其在聚合物中的分散性,对纳米TiO₂进行修饰处理以提高其对可见光的吸收,从而提高其光催化效率等方面探讨了可光降解塑料研究存在的问题及应用前景。     

负载金属对WO3-TiO2光催化剂结构与催化性能的影响

用溶胶-凝胶和浸渍-还原相结合的方法制得M/WO₃-TiO₂ (M＝Pd, Cu, Ni, Ag)光催化剂. 利用X射线衍射(XRD)、程序升温还原(TPR)、红外(IR)、程序升温脱附(TPD)、紫外-可见漫反射光谱(UV-Vis-DRS)和光反应器等技术研究了复合半导体负载金属的物相结构、光吸收性能和光催化反应性能. 结果表明: 金属负载在复合半导体上延迟了TiO₂由锐钛矿向金红石相转化, 增强W与载体TiO₂的相互作用, 使TiO₂光吸收限发生蓝移, 对可见光部分的吸收明显增加; 固体材料吸光性能强弱顺序Pd/WO₃-TiO₂＞Cu/WO₃-TiO₂＞Ag/WO₃-TiO₂＞Ni/WO₃-TiO₂; 金属Pd对CO₂吸附能力过强, 卧式吸附态脱附温度高, 光催化效率不高; 金属Cu对CO₂吸附能力适中, CO₂与C₃H₆脱附温度较接近, 实现了“光-表面-热”协同作用, 光量子效率最高, 达到19.7%.     

负载金属对WO3-TiO2光催化剂结构与催化性能的影响

用溶胶-凝胶和浸渍-还原相结合的方法制得M/WO₃-TiO₂ (M＝Pd, Cu, Ni, Ag)光催化剂. 利用X射线衍射(XRD)、程序升温还原(TPR)、红外(IR)、程序升温脱附(TPD)、紫外-可见漫反射光谱(UV-Vis-DRS)和光反应器等技术研究了复合半导体负载金属的物相结构、光吸收性能和光催化反应性能. 结果表明: 金属负载在复合半导体上延迟了TiO₂由锐钛矿向金红石相转化, 增强W与载体TiO₂的相互作用, 使TiO₂光吸收限发生蓝移, 对可见光部分的吸收明显增加; 固体材料吸光性能强弱顺序Pd/WO₃-TiO₂＞Cu/WO₃-TiO₂＞Ag/WO₃-TiO₂＞Ni/WO₃-TiO₂; 金属Pd对CO₂吸附能力过强, 卧式吸附态脱附温度高, 光催化效率不高; 金属Cu对CO₂吸附能力适中, CO₂与C₃H₆脱附温度较接近, 实现了“光-表面-热”协同作用, 光量子效率最高, 达到19.7%.     

微/纳复合型可见光光电材料Ag-石墨烯-TiO2的制备及应用

基于静电纺丝技术构筑了稳定均一的Ag-石墨烯-TiO₂纳米复合纤维;并利用SEM、TEM、XRD、EDS和Raman等表征了材料的微观结构与组分;随后,我们研究了该复合纤维在可见光下的光电转换性能。结果表明：掺杂既可降低TiO₂材料的禁带宽度,也能减缓光生电子与空穴的复合淬灭;Ag纳米晶的局域等离激元可增强纤维对可见光的吸收,石墨烯能促进光生电子与空穴的有效分离;可见光条件下,相比较于单一的TiO₂纳米纤维,复合纤维的光电流密度提高4倍,达到0.81μA·cm^-2。     

微/纳复合型可见光光电材料Ag-石墨烯-TiO2的制备及应用

基于静电纺丝技术构筑了稳定均一的Ag-石墨烯-TiO₂纳米复合纤维;并利用SEM、TEM、XRD、EDS和Raman等表征了材料的微观结构与组分;随后,我们研究了该复合纤维在可见光下的光电转换性能。结果表明：掺杂既可降低TiO₂材料的禁带宽度,也能减缓光生电子与空穴的复合淬灭;Ag纳米晶的局域等离激元可增强纤维对可见光的吸收,石墨烯能促进光生电子与空穴的有效分离;可见光条件下,相比较于单一的TiO₂纳米纤维,复合纤维的光电流密度提高4倍,达到0.81 μA·cm^-2。     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

A Simple Method for the Preparation of TiO2/Ag‐AgCl@Polypyrrole Composite and Its Enhanced Visible‐Light Photocatalytic Activity

A novel and facile method was developed to prepare a visible‐light driven TiO₂/Ag‐AgCl@polypyrrole (PPy) photocatalyst with Ag‐AgCl nanoparticles supported on TiO₂ nanofibers and covered by a thin PPy shell. During the synthesis, the PPy shell and Ag‐AgCl nanoparticles were prepared simultaneously onto TiO₂ nanofibers, which simplified the preparation procedure. In addition, because Ag‐AgCl aggregates were fabricated via partly etching the Ag nanoparticles, their size was well controlled at the nanoscale, which was beneficial for improvement of the contact surface area. Compared with reference photocatalysts, the TiO₂/Ag‐AgCl@PPy composite exhibited an enhanced photodegradation activity towards rhodamine B under visible‐light irradiation. The superior photocatalytic property originated from synergistic effects between TiO₂ nanofibers, Ag‐AgCl nanoparticles and the PPy shell. Furthermore, the TiO₂/Ag‐AgCl@PPy composite could be easily separated and recycled without obvious reduction in activity.     

Synthesis,Characterization, and Photocatalytic Properties of Ag/TiO2 Composite Nanofibers Prepared by Electrospinning

Ag nanoparticles (Ag NPs) embedded titanium dioxide (TiO₂) nanofibers were fabricated by colloidal sol process, electrospinning, and calcination technique. Calcination of the electrospun nanofibers were heat treated at 600°C for 180 minutes in air atmosphere. X-ray diffraction patterns exhibited that the anatase phase and silver coexisted in the resulted Ag NPs/TiO₂ nanofibers; transmission electron microscopy demonstrated Ag NPs well spread in the porous microstructure of composite fibers. The prepared nanofibers were utilized as photocatalyst for degradation of methyl orange. The degradation rate of methyl orange dye solution containing Ag/TiO₂ composite nanofibers is 99% only after irradiation for 3 hours. It is proposed that these new Ag NPs/TiO₂ composite nanofibers will have potential application in water pollution treatment.      

New synthesis of excellent visible-light TiO2−xNx photocatalyst using a very simple method

An excellent visible-light-responsive (from 400 to 550 nm) TiO_2−xN_x photocatalyst was prepared by a simple wet method. Hydrazine was used as a new nitrogen resource in this paper. Self-made amorphous titanium dioxide precursor powders were dipped into hydrazine hydrate, and calcined at low temperature (110 °C) in the air. The TiO_2−xN_x was successfully synthesized, following by spontaneous combustion. The photocatalyst was characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), transmission electron microscope (TEM), UV-Vis diffuse reflectance spectrometer (DRS), and X-ray photoelectron spectroscopy (XPS). Analysis of XPS indicated that N atoms were incorporated into the lattice of the titania crystal during the combustion of hydrazine on the surface of TiO₂. Ethylene was selected as a target pollutant under visible-light excitation to evaluate the activity of this photocatalyst. The newly prepared TiO_2−xN_x photocatalyst with strong photocatalytic activity and high photochemical stability under visible-light irradiation was firstly demonstrated in the experiment.     

Ag_3PO_4/MoS_2纳米片复合催化剂制备及可见光催化性能

采用机械球磨法成功制备Ag_3PO_4/MoS_2纳米片复合催化剂。运用X射线衍射仪(XRD)、透射电子显微镜(TEM)、扫描电子显微镜(SEM)、紫外可见漫反射光谱(UV-Vis)和荧光发射光谱(PL)对复合催化剂的结构和形貌进行了表征。结果表明,Ag_3PO_4纳米粒子均匀地附着在MoS_2纳米片层结构上,两者形成紧密结合。以亚甲基蓝为模拟污染物,研究复合催化剂在可见光照射下的光催化特性;通过循环实验考察复合催化剂的稳定性。结果显示,含有1%的MoS_2纳米片与Ag_3PO_4形成的复合催化剂在30 min内对亚甲基蓝的降解率为95%,其降解动力学常数是纯相Ag_3PO_4的2倍。经过5次循环实验后复合催化剂对于亚甲基蓝的降解率为84%,而纯Ag_3PO_4对于亚甲基蓝的降解率仅为35%。Ag_3PO_4/MoS_2纳米片复合催化剂具有优良的光催化活性和高稳定性,主要归因于二硫化钼纳米片与磷酸银形成异质结,磷酸银激发的电子和二硫化钼纳米片产生的空穴直接复合,从而促使光生电子从磷酸银晶体表面快速分离,减轻了磷酸银的光电子腐蚀,同时也提高了复合物的光催化活性。     

Ag3PO4/MoS2纳米片复合催化剂制备及可见光催化性能

采用机械球磨法成功制备Ag₃PO₄/MoS₂纳米片复合催化剂。运用X射线衍射仪（XRD）、透射电子显微镜（TEM）、扫描电子显微镜（SEM）、紫外可见漫反射光谱（UV-Vis）和荧光发射光谱（PL）对复合催化剂的结构和形貌进行了表征。结果表明,Ag₃PO₄纳米粒子均匀地附着在MoS₂纳米片层结构上,两者形成紧密结合。以亚甲基蓝为模拟污染物,研究复合催化剂在可见光照射下的光催化特性;通过循环实验考察复合催化剂的稳定性。结果显示,含有1%的MoS₂纳米片与Ag₃PO₄形成的复合催化剂在30 min内对亚甲基蓝的降解率为95%,其降解动力学常数是纯相Ag₃PO₄的2倍。经过5次循环实验后复合催化剂对于亚甲基蓝的降解率为84%,而纯Ag₃PO₄对于亚甲基蓝的降解率仅为35%。Ag₃PO₄/MoS₂纳米片复合催化剂具有优良的光催化活性和高稳定性,主要归因于二硫化钼纳米片与磷酸银形成异质结,磷酸银激发的电子和二硫化钼纳米片产生的空穴直接复合,从而促使光生电子从磷酸银晶体表面快速分离,减轻了磷酸银的光电子腐蚀,同时也提高了复合物的光催化活性。     

CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基底表面制备一层TiO2纳米管阵列薄膜,然后通过水热反应在TiO2纳米管上负载CdS纳米粒子,形成CdS/TiO2纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO2纳米管的光电性能和光催化活性,结果表明,相比于TiO2纳米管,CdS/TiO2纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

Preparation of Ag deposited TiO2 (Ag/TiO2) composites and investigation on visible-light photocatalytic degradation activity in magnetic field

In this study, Ag deposited TiO₂ (Ag/TiO₂) composites were prepared by three different methods (Ultraviolet Irradiation Deposition (UID), Vitamin C Reduction (VCR) and Sodium Borohydride Reduction (SBR)) for the visible-light photocatalytic degradation of organic dyes in magnetic field. And then the prepared Ag deposited TiO₂ (Ag/TiO₂) composites were characterized physically by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The visible-light photocatalytic activities of these three kinds of Ag deposited TiO₂ (Ag/TiO₂) composites were examined and compared through the degradation of several organic dyes under visible-light irradiation in magnetic field. In addition, some influence factors such as visible-light irradiation time, organic dye concentration, revolution speed, magnetic field intensity and organic dye kind on the visible-light photocatalytic activity of Ag deposited TiO₂ (Ag/TiO₂) composite were reviewed. The research results showed that the presence of magnetic field significantly enhanced the visible-light photocatalytic activity of Ag deposited TiO₂ (Ag/TiO₂) composites and then contributed to the degradation of organic dyes.     

Synthesis and photocatalytic performance of Ag/AgCl/ZnO tetrapod composites

Ag/AgCl is a visible-light plasmonic photocatalyst that has attracted considerable attention because of its high visible-light absorption and activity owing to the surface plasmon resonance of noble-metal nanoparticles. In this study, Ag/AgCl/ZnO tetrapod composite was prepared by introducing ZnO tetrapods into Ag/AgCl prepared by a polydopamine reduction route. Ag/AgCl was densely deposited on the three-dimensional support framework provided by the ZnO tetrapods. The framework possessed a certain degree of porosity, thereby improving the specific surface area of the Ag/AgCl/ZnO composite. The interaction of ZnO with Ag/AgCl further increased the separation and transfer of electron–hole pairs. The Ag/AgCl/ZnO composite showed excellent photocatalytic activity and good stability. Under xenon lamp irradiation for 20 min, degradation of rhodamine B reached 90%. After four recycling tests, degradation remained stable without any sign of reduction. Ag/AgCl/ZnO tetrapod composite is shown to be a kind of green photocatalyst offering high activity, good stability, and recyclability.

     

脉冲沉积制备Cu2O/TiO2纳米管异质结的可见光光催化性能

在用阳极氧化法制备有序排列TiO₂纳米管阵列薄膜的基础上,引入脉冲沉积工艺,成功实现了均匀、弥散分布的Cu₂O纳米颗粒修饰改性TiO₂纳米管阵列,形成Cu₂O/TiO₂ 纳米管异质结复合材料. 利用场发射扫描电镜（FESEM）、场发射透射电镜（FETEM）、X射线衍射（XRD）、X射线光电子能谱（XPS）和紫外-可见漫反射光谱（UV-Vis DRS）对样品进行表征,重点研究了Cu₂O/TiO₂ 纳米管异质结的光电化学特性和对甲基橙（MO）的可见光催化降解性能. 结果表明,Cu₂O纳米颗粒均匀附着在TiO₂纳米管阵列的管口和中部位置,所制备的Cu₂O/TiO₂ 纳米管异质结具有高效的可见光光催化性能;在浓度为0.01 mol·L^-1的CuSO₄溶液中制得的Cu₂O/TiO₂纳米管异质结表现出最好的电化学特性和光催化性能;另外,对Cu₂O纳米颗粒影响光催化活性的机理进行了讨论.