CdTe/CdS共敏化TiO2电极材料的制备与光电性能

将电沉积法和化学浴沉积法结合,分别将CdTe和CdS量子点纳米晶材料引入到TiO₂纳米管阵列上制备CdTe/CdS量子点共敏化TiO₂光电极。利用扫描电镜、X射线衍射和X射线能量色散光谱等测试手段对所得样品的形貌、晶型和组分进行表征。在模拟太阳光照射条件下,通过电化学工作站测试其光电化学性能。研究结果表明,相对于单一量子点敏化CdS/TiO₂和CdTe/TiO₂光电极而言,共敏化CdTe/CdS/TiO₂光电极表现出更好的光电转化性能,短路电流密度和光电转换效率分别可以达到3.1 mA·cm^-2和1.85%。此外,采用电化学阻抗测试技术对材料性能提升的原因进行深入的探究。     

Bi2S3/CdSe共修饰TiO2纳米管膜的构建及其光电化学阴极保护效应

为获得良好光电化学性能的TiO₂半导体复合膜,采用Bi₂S₃和CdSe对TiO₂纳米管膜进行共修饰。以阳极氧化法在Ti表面先制备TiO₂纳米管膜,再通过恒电流电沉积和连续离子层吸附反应在纳米管表面依次沉积CdSe和Bi₂S₃,构建了具有级联能带结构的Bi₂S₃/CdSe共修饰的TiO₂纳米管复合膜。结果表明,Bi₂S₃/CdSe/TiO₂纳米管复合膜对可见光吸收显著增强,光电化学性能大幅度提高。白光照射下,复合膜的光电流密度为670 μA·cm^-2,达到了纯TiO₂纳米管膜的17.6倍。Bi₂S₃/CdSe/TiO₂复合膜作为光阳极可使0.5 mol·L^-1 NaCl溶液中的403不锈钢的电位相对于腐蚀电位下降690 mV,显示出良好的光电化学阴极保护效应。     

脉冲沉积制备Cu2O/TiO2纳米管异质结的可见光光催化性能

在用阳极氧化法制备有序排列TiO₂纳米管阵列薄膜的基础上,引入脉冲沉积工艺,成功实现了均匀、弥散分布的Cu₂O纳米颗粒修饰改性TiO₂纳米管阵列,形成Cu₂O/TiO₂ 纳米管异质结复合材料. 利用场发射扫描电镜（FESEM）、场发射透射电镜（FETEM）、X射线衍射（XRD）、X射线光电子能谱（XPS）和紫外-可见漫反射光谱（UV-Vis DRS）对样品进行表征,重点研究了Cu₂O/TiO₂ 纳米管异质结的光电化学特性和对甲基橙（MO）的可见光催化降解性能. 结果表明,Cu₂O纳米颗粒均匀附着在TiO₂纳米管阵列的管口和中部位置,所制备的Cu₂O/TiO₂ 纳米管异质结具有高效的可见光光催化性能;在浓度为0.01 mol·L^-1的CuSO₄溶液中制得的Cu₂O/TiO₂纳米管异质结表现出最好的电化学特性和光催化性能;另外,对Cu₂O纳米颗粒影响光催化活性的机理进行了讨论.     

SnO2TiO2 复合半导体纳米薄膜的研究进展

本文概述了SnO₂TiO₂ 复合半导体纳米薄膜的发展历史和研究现状,对比分析了“混合”、“核壳”和“叠层”3 种复合薄膜的结构和性能特点,着重论述了叠层结构的SnO₂ /TiO₂复合薄膜的光电化学和光催化特性。结合作者的研究工作,探讨了SnO₂ /TiO₂双层复合薄膜上下层厚度对其光催化活性的影响,指出复合薄膜光催化活性的提高可归因于电子从TiO₂ 向SnO₂ 的迁移。最后对SnO₂ /TiO₂复合薄膜的局限性和发展潜势做一简要分析,强调了该复合薄膜本身的应用特点。     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

多壁碳纳米管修饰的CdS/TiO2复合光催化材料的制备及其光解水制氢特性

以P25 TiO₂(德国Degussa化学公司)粉末为原料采用溶胶-凝胶法制备了含有不同CdS质量分数的复合光催化剂,利用多壁碳纳米管(MWCNTs)对CdS/TiO₂进行修饰,制备了一系列不同CdS含量的MWCNTs/CdS/TiO₂光催化材料。对所得的光催化剂进行了扫描电镜、低温氮吸附-脱附及光解水制氢活性的表征。研究了MWCNTs对CdS/TiO₂催化剂体系光解水制氢活性的影响。结果表明,MWCNTs的引入均使得光解水产氢量(14.0 μmol)增加,与未加入MWCNTs的复合光化剂产氢量(11.6 μmol)相比,平均产氢率增加了18%,最高可达21%。     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附-脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

TiO2-MoO3复合纳米管阵列薄膜的制备及其可见光活性

通过阳极氧化的方法制备TiO₂纳米管薄膜, 在MoO₃存在的条件下对该薄膜进行热处理得到TiO₂-MoO₃复合纳米管阵列薄膜. 利用X射线衍射(XRD), 扫描电子显微镜(SEM), X射线光电子能谱(XPS), 电化学阻抗谱(EIS), Mott-Schottky 及光电化学方法对得到的薄膜进行了表征. XRD结果表明, TiO₂-MoO₃复合纳米管薄膜中的TiO₂主要为锐钛矿晶型. SEM实验证实了薄膜纳米管结构的存在, 样品中的MoO₃均匀地分散在TiO₂纳米管表面. 利用XPS方法分析了TiO₂-MoO₃复合纳米管薄膜元素的组成, 结果表明, MoO₃在TiO₂表面形成TiO₂-MoO₃复合纳米管薄膜. 研究了热处理温度以及热处理时间对样品的光电化学性能的影响, 相对于单纯TiO₂纳米管薄膜, 适量引入MoO₃提高了样品在可见光区的光电响应能力, 样品的平带电位负移. 在450 °C热处理60 min制得的TiO₂-MoO₃复合半导体纳米管阵列薄膜光电响应活性最高.     

聚3-甲基噻吩修饰硫化物量子点连接纳米结构TiO2膜的光电化学研究

采用原位化学法在纳米结构TiO₂膜上制备了量子点CdS, PbS (Q-CdS, Q-PbS), 并用电化学方法在TiO₂/Q-CdS, TiO₂/Q-PbS表面聚合3-甲基噻吩[poly(3-Methylthiophene, PMeT)]. 用光电化学方法研究了PMeT修饰Q-CdS, Q-PbS连接TiO₂纳米结构膜, 实验结果表明, PMeT和Q-CdS, Q-PbS单独修饰纳米结构TiO₂电极和PMeT修饰Q-CdS, Q-PbS连接纳米结构TiO₂电极的光电流产生的起始波长都向长波方向移动; 一定条件下在可见光区光电转换效率均较纳米结构TiO₂的光电转换效率有明显的提高; 聚3-甲基噻吩(PMeT)与Q-CdS, Q-PbS连接的纳米结构TiO₂之间存在p-n异质结. 在一定条件下p-n异质结的存在有利于光生电子/空穴的分离, 在本文实验条件下PMeT修饰Q-CdS, Q-PbS连接纳米结构TiO₂电极最高的单色光的光电转换效率分别为11%和7%.     

CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基底表面制备一层TiO2纳米管阵列薄膜,然后通过水热反应在TiO2纳米管上负载CdS纳米粒子,形成CdS/TiO2纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO2纳米管的光电性能和光催化活性,结果表明,相比于TiO2纳米管,CdS/TiO2纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

Synthesis and Photocatalytic Activity of TiO2/CdS Nanocomposites with Co-Exposed Anatase Highly Reactive Facets

In this work, TiO₂/CdS nanocomposites with co-exposed {101}/[111]-facets (NH4F-TiO2/CdS), {101}/{010} facets (FMA-TiO2/CdS), and {101}/{010}/[111]-facets (HF-TiO2/CdS and Urea-TiO2/CdS) were successfully synthesized through a one-pot solvothermal method by using [Ti₄O₉]²⁻ colloidal solution containing CdS crystals as the precursor. The crystal structure, morphology, specific surface area, pore size distribution, separation, and recombination of photogenerated electrons/holes of the TiO₂/CdS nanocomposites were characterized. The photocatalytic activity and cycling performance of the TiO₂/CdS nanocomposites were also investigated. The results showed that as-prepared FMA-TiO₂/CdS with co-exposed {101}/{010} facets exhibited the highest photocatalytic activity in the process of photocatalytic degradation of methyl orange (MO), and its degradation efficiency was 88.4%. The rate constants of FMA-TiO₂/CdS was 0.0167 min⁻¹, which was 55.7, 4.0, 3.7, 3.5, 3.3, and 1.9 times of No catalyst, CdS, HF-TiO₂/CdS, NH₄F-TiO₂/CdS, CM-TiO₂, Urea-TiO₂/CdS, respectively. The highest photocatalytic activity of FMA-TiO₂/CdS could be attributed to the synergistic effects of the largest surface energy, co-exposed {101}/{010} facets, the lowest photoluminescence intensity, lower charge-transfer resistance, and a higher charge-transfer efficiency.     

CdTe/CdS共敏化TiO2电极材料的制备与光电性能

将电沉积法和化学浴沉积法结合,分别将CdTe和CdS量子点纳米晶材料引入到TiO_2纳米管阵列上制备CdTe/CdS量子点共敏化TiO_2光电极。利用扫描电镜、X射线衍射和X射线能量色散光谱等测试手段对所得样品的形貌、晶型和组分进行表征。在模拟太阳光照射条件下,通过电化学工作站测试其光电化学性能。研究结果表明,相对于单一量子点敏化CdS/TiO_2和CdTe/TiO_2光电极而言,共敏化CdTe/CdS/TiO_2光电极表现出更好的光电转化性能,短路电流密度和光电转换效率分别可以达到3.1 m A·cm~(-2)和1.85%。此外,采用电化学阻抗测试技术对材料性能提升的原因进行深入的探究。     

CdS/TiO2 composite films for methylene blue photodecomposition under visible light irradiation and non-photocorrosion of cadmium sulfide

Cadmium sulfide/titanium dioxide (CdS/TiO₂) composite films were grown on glass by the chemical bath deposition (DBQ) and sol-gel/dip coating methods, respectively, in order to increase the photocatalytic activity of TiO₂ in photodegradation processes. The influence of the CdS deposition time on the morphology, optical absorption, and phononic modes of the composites were examined. Scanning electron microscopy (SEM) images showed clearly the CdS deposit on the TiO₂ surface. The absorbance spectra indicated that the absorption of composites depends on the CdS deposition time and the absorption edges are shifted to the visible range. Micro Raman spectra exhibited the phonons associated with the TiO₂ anatase and the longitudinal optic (LO) phonon of CdS whose intensity increases with the CdS deposition time. Photodegradation of methylene blue (MB) under visible light irradiation was observed in all films and the results were compared with those obtained with TiO₂ films. The decomposition is higher for the composite with the CdS deposition time of 15 min. This optimal deposition time allows maximal enhancement of the charge carriers transfer to TiO₂ involved in the photocatalysis. No signal associated with cadmium was detected by the atomic absorption spectroscopy (AAS), which means that the CdS photocorrosion does not occur since trap centers such as OH-Cd-S and Cl^?, which trap holes and inhibit the photocorrosion, are produced during the growth process.     

Label-free Photoelectrochemical Aptasensor for the Determination of Carcinoembryonic Antigen Using a Cadmum Sulfide Quantum Dot Sensitized Titanium (IV) Oxide Nanotube Electrode

A label-free photoelectrochemical aptasensor for the sensitive and selective determination of carcinoembryonic antigen was constructed based on a CdS quantum dot sensitized TiO₂ nanotube electrode. TiO₂ nanotubes with highly ordered structure and more active sites than bulk TiO₂ were prepared with an electrochemical anodic oxidation process. The CdS quantum dots were immobilized on the TiO₂ nanotubes using poly(diallyldimethylammonium chloride) as a bridge. Due to the energy level match between TiO₂ and CdS, the CdS quantum dots/TiO₂ nanotubes electrode exhibits excellent photoelectrochemical performance. The large surface area of the electrode also allows for capturing large numbers of aptamers. The fine photoelectrochemical performance and the large surface area of the electrode greatly enhanced the detection sensitivity. Under the optimal conditions, the prepared photoelectrochemical aptasensor presents desirable analytical properties for the determination of carcinoembryonic antigen in the range of 0.05 to 10?ng?mL^?1 with a detection limit of 0.014?ng?mL^?1. The application of the designed protocol was investigated by analyzing carcinoembryonic antigen in human serum samples with recoveries from 80.0 to 115.0%. This simple and sensitive method provides an alternative tool to standard biochemical assays.     

Mechanism of the formation of photosensitive nanostructured TiO<Subscript>2</Subscript> with low content of CdS nanoparticles

A method for synthesizing a CdS/TiO₂ composite material, active in the visible region, was described. The CdS/TiO₂ composite was obtained by the sol–gel synthesis of nanostructured TiO₂ in a medium of a stable colloidal solution of CdS nanoparticles. The TiO₂ matrix produced by the sol–gel process is amorphous and contains a nanocrystalline anatase phase, the content of which depends on the Ti(OBu)₄ hydrolysis rate. The content of CdS nanoparticles forming in the colloidal solution and participating in the TiO₂ matrix sensitization is determined by the initial CdS: Ti(OBu)₄ ratio. Although the content of CdS nanoparticles in the composite is low (no more than 3 wt %), the composite demonstrates catalytic activity in the visible region, thus proving the possibility of reducing the content of toxic CdS nanoparticles in the TiO₂ matrix without decreasing the photosensitivity of the CdS/TiO₂ composite.     

CdS‐Encapsulated TiO2 Nanotube Arrays Lidded with ZnO Nanorod Layers and Their Photoelectrocatalytic Applications

A novel TiO₂ nanotube array/CdS nanoparticle/ZnO nanorod (TiO₂ NT/CdS/ZnO NR) photocatalyst was constructed which exhibited a wide‐absorption (200–535 nm) response in the UV/Vis region and was applied for the photoelectrocatalytic (PEC) degradation of dye wastewater. This was achieved by chemically assembling CdS into the TiO₂ NTs and then constructing a ZnO NR layer on the TiO₂ NT/CdS surface. Scanning electron microscopy (SEM) results showed that a new structure had been obtained. The TiO₂ NTs looked like many “empty bottles” and the ZnO NR layer served as a big lid. Meanwhile the CdS NPs were encapsulated between them with good protection. After being sensitized by the CdS NPs, the absorption‐band edge of the obtained photocatalyst was obviously red‐shifted to the visible region, and the band gap was reduced from its original 3.20 eV to 2.32 eV. Photoelectric‐property tests indicated that the TiO₂ NT/CdS/ZnO NR material maintained a very high PEC activity in both the ultraviolet (UV) and the visible region. The maximum photoelectric conversion efficiencies of TiO₂ NT/CdS/ZnO NR were 31.8 and 5.98 % under UV light (365 nm) and visible light (420–800 nm), respectively. In the PEC oxidation, TiO₂ NT/CdS/ZnO NR exhibited a higher removal ability for methyl orange (MO) and a high stability. The kinetic constants were 1.77×10^?4 s^?1 under UV light, which was almost 5.9 and 2.6 times of those on pure TiO₂ NTs and TiO₂ NT/ZnO NR, and 2.5×10^?4 s^?1 under visible light, 2.4 times those on TiO₂ NT/CdS.     

全固态Z-型CdS/Au/Bi2MoO6异质结的构筑及其光催化性能

采用简单的化学还原沉积和二次水热的方法成功制备了CdS和Au共同修饰Z型CdS/Au/Bi2MoO6(CdS/Au/BMO)光催化剂。通过X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、扫描电子显微镜(SEM)等测试技术对其组成、形貌、光吸收特性和光电化学性能等进行系统表征。实验结果表明,CdS/Au/BMO-2复合材料在可见光照射下表现出最佳的降解效率,其降解RhB的速率常数约为BMO的8.8倍和CdS的20倍。Au NPs作为固态电子媒介,为光生电子的传输和转移提供了一个通道,同时Au NPs的表面等离子体共振(SPR)效应和CdS纳米粒子显著拓宽了催化体系对可见光的响应范围;通过对催化剂的组成、结构和光电性能表征,确定了CdS/Au/BMO的能带结构,进而探讨了CdS/Au/BMO活性增强机制。     

Quantum dots co-sensitized solar cells: a new assembly process of CdS/CdSe linked to mesoscopic TiO2-nano-SiO2 hybrid film

A green and simple method was found to prepare CdS/CdSe co-sensitized photoelectrodes for the quantum dots sensitized solar cells application. All the assembly processes of CdS and CdSe quantum dots (QDs) were carried out in aqueous solution. CdS and CdSe QDs were sequentially assembled onto TiO₂-nano-SiO₂ hybrid film by two steps. Firstly, CdS QDs were deposited in situ over TiO₂-nano-SiO₂ hybrid film by the successive ionic layer adsorption and reaction (SILAR) process in water. Secondly, using 3-mercaptopropionic acid (3-MPA) as a linker molecule, the pre-prepared colloidal CdSe QDs (~3.0 nm) dissolved in water was linked onto the TiO₂-nano-SiO₂ hybrid film by the self-assembled monolayer technique with the mode of dropwise. The mode is simple and advantageous to saving materials and time. The results show that the photovoltaic performance of the cells is enhanced with the increase of SILAR cycles for TiO₂-nano-SiO₂/CdS photoelectrode. The power conversion efficiency of 2.15 % was achieved using the co-sensitization photoelectrode prepared by using 6 SILAR cycles of CdS plus CdSe (TiO₂-nano-SiO₂/CdS(6)/CdSe) under the illumination of one sun (AM1.5, 100 mW/cm²).