电化学阻抗法研究降低环氧涂层的吸水性能

降低固化环氧树脂吸水性能是提高其可靠性与寿命的重要前提之一。作者曾将常用的线型酚醛树脂(NOV)中吸水性较强的羟基用乙酸基取代,制成乙酸线型酚醛酯树脂(NOVA),并作为邻甲酚环氧树脂(ECN)的新型固化剂。用称重法研究,发现采用NOVA代替NOV所得的新型固化环氧树脂样片的饱和吸水率(M~∞)可降低一半以上。由于环氧涂层一般很薄,难以称重法研究其吸水性能,本文改用电化学阻抗法研究上述新型环氧涂层的吸水性能所得的一些有兴趣的结果,并作出了初步的解释。     

化学结构变化对刚棒状环氧树脂相行为和热力学性能的影响

用线性酚醛树脂(PN)和4-氨基苯基氨基砜(SAA)作为固化剂, 与刚性棒状环氧树脂联苯环氧(DGEBP)、四甲基联苯环氧(DGETMBP)和传统双酚A环氧树脂(DGEBA)分别进行固化. 研究了固化剂和环氧树脂化学结构的改变对热固网络相行为和热力学性能的影响. 结果表明, 刚性环氧网络比传统的DGEBA具有更好的热力学性能. DGEBP可形成不同类型的取向网络, 而取向态的类型也直接影响了热固网络的热力学性能. 用扫描电镜(SEM)观察不同网络体系的断裂面结构, 发现取向的刚性棒状环氧网络的断裂面呈韧性断裂, 而其它无定形环氧网络则呈典型的脆性断裂.     

胺固化环氧酚醛树脂对Hg~(2+)的吸附性能

螯合树脂能与金属离子形成稳定的配合物,在无机、冶金、分析药物、催化、海洋化学、放射化学、环境保护各领域都有非常重要的应用[1-3]。我们曾以酚醛树脂为大分子骨架与多胺反应制备了一系列螯合树脂并对其结构及对多种金属离子的吸附性能进行了探讨[4,5]。本文则以线型环氧酚醛树脂为大分子骨架、多乙烯多胺为固化剂,制备了五种不同氮含量的氨基环氧酚醛螯合树脂,并考察其对金属离子Ｈｇ2+的吸附性能。1　实验部分1.1　仪器与试剂ＮｉｃｏｌｅｔＭＡＧＮＡ ＩＲ550(ＳｅｒｉｅｓＩＩ)红外分光光度计,ＳＨＡ-Ｃ水浴恒温振荡器,ＰＥ2000…     

线性酚醛树脂在集成电路领域的应用与研究进展

在集成电路领域中,线性酚醛树脂作为基础树脂,是关键的功能材料。然而,传统的酚醛树脂存在稳定性差、感光速度慢、透明度、分辨率和机械强度低等问题,增加了应用成本和技术难度,降低了酚醛树脂在集成电路领域的经济效益。因此,需要对传统线性酚醛树脂进行改性以更好地应用于集成电路领域。本文综述了近年来线性酚醛树脂在芯片光刻胶、电子封装及覆铜板应用的研究现状,总结了目前改性线性酚醛树脂的主要方法,并展望了线性酚醛树脂的发展趋势,为未来高性能集成电路应用材料的研发提供参考。     

不同碳源对LiFePO4/C锂离子电池正极材料性能的影响

以自制的正磷酸铁为铁和磷源,氢氧化锂为锂源,分别以酚醛树脂、葡萄糖、柠檬酸为碳源,采用碳热还原法合成LiFePO4/C锂离子电池正极材料.采用X射线衍射(XRD)、扫描电镜(SEM)、四探针电导测定及恒流充放电测试分别对合成样品的物相、粒径、表面形貌、电导率及电性能进行了分析.结果表明以酚醛树脂为碳源制备的Li FeP...     

二元羧酸半酯与环氧化合物反应动力学研究

用于印制电路板 ( PCB)的传统的热固化或光固化阻焊油墨是利用屏印的方法把图案印刷在覆铜板上 ,然后固化 .通过这种方法得到的图案不够精细 ,应用上也受到一定限制 .为此 ,近年来国际上研制出一类新型的阻焊油墨——碱液显影型阻焊油墨 [1～ 3] .它是通过曝光、显影及后固化等步骤形成精确的图案 ,可用于制备高密度的电路板 .通常 ,碱水显影型阻焊油墨由碱溶性光敏树脂 (组分 A)、环氧化合物 (组分 B)、光引发剂、热固化剂和稀释剂组成 .组分 A由二元羧酸与含有光聚合性双键的线性酚醛型环氧化合物通过半酯化反应得到 ,羧基的引入使其具…     

三组份酚醛树脂冷压制备离合器摩擦材料

提出采用三组份改性酚醛树脂和混杂纤维冷压工艺制备离合器摩擦材料.三组份酚醛树脂为硼改性腰果壳油液体树脂、三聚氰胺改性酚醛液体树脂和芳烷基改性酚醛固体树脂.混杂纤维由玻璃纤维和复合包芯纱混杂构成.结果表明,采用三组份酚醛树脂和混杂纤维可以制备出摩擦性能良好,350℃不发生热衰退的离合器摩擦材料,且材料具有合适的孔隙率.     

电纺聚乙烯醇超细纤维膜的性能研究

由电纺制备聚乙烯醇(PVA)超细纤维膜,以扫描电镜观察纤维的微观形貌,用X射线衍射研究超细纤维膜的结晶行为,并测定了PVA超细纤维膜的力学性能和吸水性.结果表明,PVA超细纤维的平均直径为(184±26)nm,超细纤维中PVA的结晶度和晶体有序程度较浇铸膜低.超细纤维膜的拉伸强度、模量和断裂伸长率均较浇铸膜差,吸水率在300%以上,高于浇铸膜.     

汞代N-乙烯基咔唑-丙烯酸共聚物的合成与研究

制备线型和网状N-乙烯基咔唑-丙烯酸甲酯共聚物后,用三氟乙酸汞分别在四氢呋喃(THF)和二氯甲烷中进行汞化反应,得到相应的线型和网状汞代咔唑共聚物。这些共聚物经THF溶解或溶胀后,用氢氧化钠水溶液水解,得到相应的水溶性线型高分子和吸水性网状高分子,憎水性汞代咔唑共聚物在THF中由I₂取代汞;亲水性汞代咔唑共聚物在水溶液中由KI₃取代汞。汞代咔唑高分子链在不同溶剂中可以产生不同的形态变化。     

医用多孔壳聚糖膜的制备及性能研究

以邻苯二甲酸二丁酯为致孔剂,制备了多孔壳聚糖膜,并用扫描电镜对其表面和断面形貌进行了分析,同时对膜的吸水性、水蒸气透过性、比表面积、力学性能及生物相容性等进行了考察。分析结果表明:以邻苯二甲酸二丁酯为致孔剂,制备的多孔壳聚糖膜孔径均匀,吸水性好,孔隙率高,比表面积大,膜的最大吸水率、孔隙率和比表面积分别为196%、71.5%和1.0472 m2.g-1;膜的力学性能好,最大抗拉强度为273.17MN/m2。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.