含氟丙烯酸酯共聚物防粘剂的制备及其表面性能研究

以甲基异丁基甲酮为溶剂,偶氮二异丁腈为引发剂,全氟烷基乙基丙烯酸酯、丙烯酸十八酯、丙烯酸丁酯和甲基丙烯酸羟乙酯为原料,溶液聚合制得了均一的含氟丙烯酸酯共聚物防粘剂,并研究了其表面性能。结果表明:全氟烷基乙基丙烯酸酯单体的加入显著降低了共聚物的表面能,提高了共聚物膜的硬度、耐水、耐碱、耐溶剂等性能。当加入ω(氟单体)为30%时,表面能降低至14.7 mN/m,低于有机硅类防粘剂的表面能,含氟丙烯酸酯共聚物膜与压敏胶的的剥离力较低,剩余粘附率为93.2%,该共聚物膜的防粘等综合性能最好。     

含氟聚氨酯-丙烯酸酯核壳乳液的制备及性能

以甲基丙烯酸羟乙酯封端的水性聚氨酯作为大分子单体,与甲基丙烯酸甲酯及甲基丙烯酸全氟烷基乙基酯在乳液中进行自由基共聚合,制备出具有核壳结构的水性含氟聚氨酯-丙烯酸酯乳液。通过激光粒度分析仪、FT-IR、DSC、TGA、接触角、力学等表征手段,对乳液及其乳胶膜的结构和性能进行了研究,还着重探讨了甲基丙烯酸全氟烷基乙基酯的含量对乳胶膜性能的影响,结果表明:所制得的材料具有预期结构,并且具有优异的表面性能和力学性能,氟单体的引入使乳胶膜的表面能大大降低,而力学性能明显提高。     

核壳结构三元含氟丙烯酸酯乳液的制备及表征

以甲基丙烯酸三氟乙酯(Actyflon-G03)、丙烯酸丁酯(BA)、甲基丙烯酸甲酯(MMA)为原料,采用质量比为 1/1 的 OP-10/SDS 复合乳化荆,利用种子乳液聚合法,合成了核壳结构共聚物乳液.研究了温度对聚合反应、氟单体含量对聚合物膜吸水性及硬度的影响,采用 DSC、SEM-EDX、TEM 表征了共聚物膜的性能及乳胶粒子特征.结果表明:当 Actyflon-G03 含量为 23.28%时,核壳型结构粒子呈球形分布,粒径约为 80～110 nm,膜吸水率最低,硬度最高,并有 75.85%的最大转化率和 0.58%的最低凝胶率.SEM-EDX 分析显示,氟原子在成膜过程中向膜表面迁移,降低了膜的表面能.     

含氟聚氨酯-丙烯酸酯核壳乳液的制备及性能

以甲基丙烯酸羟乙酯封端的水性聚氨酯作为大分子单体,与甲基丙烯酸甲酯及甲基丙烯酸全氟烷基乙基酯在乳液中进行自由基共聚合,制得具有核壳结构的水性含氟聚氨酯-丙烯酸酯乳液。通过激光粒度分析、FT-IR、DSC、TGA、表面性能测试、力学性能测试等表征手段,对乳液及其乳胶膜的结构和性能进行了检测,另外,还着重探讨了甲基丙烯酸全氟烷基乙基酯的含量对乳胶膜性能的影响。结果表明:所制得的材料具有预期结构,并且表面能及吸水率低,力学性能优异。氟单体的引入使乳胶膜的表面能大大降低,而力学性能明显提高。     

含氟丙烯酸酯共聚乳液的制备及表征

采用十二烷基硫酸钠和壬基酚聚氧乙烯醚(OP-10)混合乳化剂，制备了粒径为40-50nm的甲基丙烯酸全氟辛基乙酯(FMA8)-甲基丙烯酸丁酯(BMA)-甲基丙烯酸(MA)共聚物乳液。通过DSC、、FTIR、^1H-NMR等手段对共聚物进行了表征。考察了乳液的稳定性、乳胶膜的吸水性和耐溶剂性以及全氟单体的含量对聚合反应的影响。     

阳离子无皂含氟丙烯酸酯的合成与表面性能

在合成甲基丙烯酸全氟辛酰氧基乙酯(FA)基础上,用半连续法制备了无皂阳离子含氟丙烯酸酯乳液。当乳液的粒径在100~200 nm、ζ电位大于40 mV时,乳液较稳定。阳离子亲水单体甲基丙烯酰氧乙基三甲基氯化铵(DMC)在含氟丙烯酸酯中质量分数为0.10~0.18、固含量小于20%时乳液的稳定性好,且随DMC含量的增加稳定性提高;含氟丙烯酸酯乳胶膜的附着力与耐磨性好,乳胶膜的透湿率随DMC的增加而增加。随热处理温度的提高,膜表面自由能下降;经160℃热处理后膜发生了交联,表面自由能为18 mN/m,与聚四氟乙烯(PTFE)的表面能相近,DMC含量对膜表面自由能影响不大。XPS分析也表明膜表面氟含量随热处理温度的提高而增加。     

带有羧基的含氟丙烯酸酯共聚物的制备及超疏水性能研究

以甲基丙烯酸、甲基丙烯酸甲酯、甲基丙烯酸全氟烷基乙基酯为单体,以可逆加成-断裂链转移方法合成含氟嵌段共聚物,同时以常规自由基溶液聚合制备相似组成的无规共聚物.采用溶剂挥发成膜方法成膜,研究共聚物组成与结构对膜表面形貌和疏水性能的影响.结果表明,羧基单体的引入改变了含氟丙烯酸酯聚合物的溶解性能和成膜性能,使用常用溶剂就可...     

核壳型含氟丙烯酸酯共聚物的合成及性能

采用饥饿态半连续种子乳液聚合方法, 在十二烷基硫酸钠(SDS)/辛基苯基聚氧乙烯醚(TX-10)复合乳化剂的作用下, 分别选用甲基丙烯酸三氟乙酯(TFEM)、甲基丙烯酸六氟正丁酯(HFBM)和甲基丙烯酸十二氟庚酯(DFHM)为含氟单体, 合成以丙烯酸正丁酯(BA)、甲基丙烯酸甲酯(MMA)和含氟单体为原料的核壳型结构含氟丙烯酸酯共聚物乳液. FTIR, 1H NMR, TEM和DSC分析结果显示, 获得了BA/MMA/含氟单体的共聚物乳液, 且乳液具有明显的核壳结构. DSC, TGA和SEM-EDX的分析显示, 核壳型结构的共聚物具有优异的热力学稳定性能和成膜性能; 长侧链或短侧链含氟单体对共聚物的热稳定性影响不明显, 但侧链较长的含氟单体所获得的聚合物在成膜过程中更易向表面迁移, 更能体现含氟聚合物的优点.     

核壳乳液聚合法制备含氟硅丙烯酸酯乳液

以氟醇RfCH2CH2OH和乙烯基硅氧烷VTES为原料合成的氟硅单体,与甲基丙烯酸甲酯、丙烯酸丁酯在复合乳化体系中通过核壳乳液聚合制备了稳定的氟硅共聚乳液。对氟硅单体和氟硅丙烯酸酯共聚物的结构用红外光谱进行了表征,结果表明,得到了目标单体和共聚物。共聚物的TEM形态观察发现,乳胶粒子具有明显的核壳结构,平均粒径在125 nm左右。与丙烯酸酯共聚物相比,氟硅丙烯酸酯共聚物乳胶膜的吸水率降低至8.32%,热分解温度提高了23℃,耐溶剂性与氟硅单体的含量关系不大。     

全氟甲基乙烯基醚和其它含氟单体乳液共聚合的竞聚率测定

分别通过气相色谱法测定了全氟甲基乙烯基醚 (PMVE)与偏氟乙烯 (VDF)以及PMVE与四氟乙烯(TFE)二元乳液共聚反应中的气相单体组成和共聚物组成 ,然后用非线性回归法 (RREVM )计算得TFE PMVE及VDF PMVE乳液共聚合反应的表观竞聚率分别为γTFE =3 89和γPMVE =0 0 5以及γVDF =1 0 6和γPMVE =0 11.结合已经测定的TFE VDF二元乳液共聚的表观竞聚率 ,计算了由VDF TFE PMVE三元乳液共聚合反应合成的共聚物组成 ,后者与由1 9F NMR实测的共聚物组成吻合     

Effect of sequence structure on wetting behaviors of fluorinated methacrylate polymers based on perfluorohexylethyl methacrylate and stearyl acrylate

Due to the non-crystalline properties of short chain perfluoroalkyl groups,using short chain perfluoroalkyl to stabilize low surface free energy polymers has been a challenging task.In this study,we prepare a series of random copolymers poly(perfluorohexylethyl methacrylate)-co-poly(stearyl acrylate) (P13FMA-co-PSA) and block copolymers poly(perfluorohexylethyl methacrylate)-b-poly(stearyl acrylate) (P13FMA-b-PSA),and systematically investigate the effects of the sequence structure and the content of 13FMA of the fluorinated copolymers on surface free energy and surface reorganization.Static/dynamic contact angle goniometry and water/oil repellency analyses demonstrate that the random polymer P13FMA-co-PSA could not achieve low surface free energy and low surface reorganization at the same time.In contrast,for the block copolymer P13FMA-b-PSA,both low surface free energy and low surface reorganization are acquired simultaneously.The results of X-ray photoelectron spectroscopy (XPS),dynamic contact angle goniometry and differential scanning calorimetry (DSC) reveal the above-mentioned properties.The consecutive 13FMA segments improve the surface fluorine density,while the consecutive SA chains enhance the crystallinity of the SA segments,and further hinder the surface reorganization of the perfluoroalkyl groups.Therefore,P13FMA-b-PSA exhibits a higher utilization efficiency of fluorine atoms and a better structural stability than P13FMA-co-PSA.     

采用XPS与接触角法研究氟聚合物表面结构与性能

本文采用接触角和变角XPS方法对FA共聚物的表面能、 表面微相结构做了进一步的研究.     

Comparison of surface properties of random, block, and graft copolymers having perfluoroalkyl and silicone-containing side chains

Fluorosilicone copolymers of random, block, and graft with both perfluoroalkyl and silicone-containing side chains were synthesized, and their surface properties and surface modification effects on PVC film were compared. It can be confirmed that the fluorosilicone copolymers of random, block, and graft exhibit very low surface free energies of 9-13 dyn/cm, depending on the perfluoroalkyl group content and their molecular structure. The inherent surface free energies of the fluorosilicone copolymers are significantly influenced by their molecular structure and perfluoroalkyl group content. It can also be found that the fluorosilicone copolymers are very effective for lowering surface free energy. The surface free energy of a copolymer/PVC blend strongly varies with perfluoroalkyl group content as well as molecular structure. The molecular structure of a fluorosilicone copolymer is as important as the perfluoroalkyl group content for their inherent surface free energies and surface modification of other polymers.     

Synthesis and characterization of a new fluorinated macroinitiator and its diblock copolymer by AGET ATRP

A new fluorinated macroinitiator of poly 2,2,3,4,4,4-hexafluorobutyl methacrylate-Br (PHFMA-Br) was prepared via activator generated by electron transfer atom transfer radical polymerization (AGET ATRP), and then a series of fluorinated block copolymers with different fluorine content were successfully synthesized from the macroinitiator by the second step AGET ATRP. GPC, FTIR and ¹H NMR data obtained verified the synthesis. Contact angle measurement indicated that proper fluorine content could decrease the surface energy and increase the contact angle of the copolymer films. XPS characterization showed that the large difference in surface energy between the block and random copolymer film resulted from the difference of the fluorine content on the surface, although the fluorine content of the two copolymers in bulk was similar. The self-assembly behavior of the fluorinated block copolymer in selective solvents was evaluated by the TEM study, and the stable micelles with a core-shell structure were observed when the copolymer content was about 1 wt%.     

Preparation and characterization of fluorine-containing acrylate copolymers by Co γ-ray radiation co-polymerization

A series of fluorine-containing acrylate copolymers were prepared by ⁶⁰Co γ-ray radiation co-polymerization in a mixed acrylate system, including butyl acrylate, acrylic acid, acrylonitrile, N-hydroxymethyl acrylamide and perfluoroalkylethyl methacrylate (FMA). The yield of the copolymers reached 96% when they were radiated for 34 h with the radiation dose of 1 kGy/h. Moreover, the surface structure and properties of the copolymers were determined by Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS) and contact angle (CA) analysis. And the glass-transition temperature was measured by dynamic mechanical thermal analysis (DMTA). It was found that the fluoropolymer was of large water static contact angle and fluorine was enriched at the polymer-air interface. The relationship between the copolymer composition, annealed temperature and static contact angle was also discussed in detail. Furthermore, when the FMA content reached 3%, the cotton treated with our products exhibited better oil repellency.     

氟硅协同改性丙烯酸树脂的合成与防污性能研究

以甲基丙烯酸十二氟庚酯(FMA)、甲基丙烯酸聚二甲基硅氧烷基酯(SMA)、甲基丙烯酸甲酯、丙烯酸正丁酯、甲基丙烯酸正丁酯和丙烯酸乙酯为共聚单体,通过溶液聚合反应合成出侧链含有机氟、有机硅的丙烯酸树脂.通过核磁共振氢谱(1H-NMR)、核磁共振氟谱(19F-NMR)、红外光谱(FTIR)对聚合物的结构进行了表征.通过扫描电镜(SEM)、接触角测试和生物评价等方法,探讨了FMA、SMA含量对树脂涂膜性能的影响.结果表明氟硅改性的丙烯酸树脂比单独含氟或含硅改性的丙烯酸树脂具有更低的表面能,而且氟硅改性的丙烯酸树脂涂膜比商业化的聚硅氧烷涂膜具有更好的防污性能.     

用含氟丙烯酸酯无规共聚物制备超疏水膜

用微乳液聚合法制备了丙烯酸全氟烷基乙酯和甲基丙烯酸甲酯的无规共聚物,并对其进行了表征.采用溶剂挥发成膜法一步制备了具有超疏水性的该聚合物膜,水滴在该聚合物膜上的静态接触角可达151°~160°,滚动角小于3°.通过扫描电子显微镜观察发现该聚合物膜表面分布了许多乳突状突起和微孔洞,并具有微米和纳米尺度相结合的复合杂化结构.该类超疏水表面的形成是由适度粗糙的表面和低表面能相互结合引起的.探讨了该类超疏水膜的形成机理.     

Preparation and surface properties of latexes with fluorine enriched in the shell by silicon monomer crosslinking

A series of core-shell acrylic copolymer latexes containing fluorine enriched in the shell have been prepared by emulsion polymerization of a variety of hydrocarbon monomers with (perfluoroalkyl)methyl methacrylate and vinyltriethoxysilicone. In the presence of a reactive anionic and a long chain anionic-nonionic emulsifier, the core-shell latexes were prepared and characterized by transmission electron microscopy (TEM) and tapping-mode atomic force microscopy (AFM). From AFM and contact angle measurements, it was observed that the resulting fluorine and silicon-containing acrylic copolymers with surface energy as low as 15.5 mN/m formed a dense and gradient film containing a surface layer with high a fluorine content, and that the fluorinated particles can be fixed on the surface due to the crosslinking reaction of multi-functional silicon monomer even though the fluorinated carbon number was not enough to crystallize.     

Depth profiling of latex blends of fluorinated and fluorine‐free acrylates with laser‐induced secondary mass spectrometry

We explored phase separation and self‐assembly of perfluoroalkyl segments at the surface of polymer films obtained from latices of semifluorinated acrylate copolymers and the corresponding latex blends of nonfluorinated and semifluorinated polyacrylates. With laser‐induced secondary mass spectrometry the fluorine distribution was measured after annealing above the minimum film‐forming temperature of the polymers up to a depth of several micrometers. Depth profiles of a semifluorinated acrylate homopolymer and latex blends thereof with fluorine‐free alkylacrylates with 25, 50, and 75 mol % semifluorinated acrylate as well as a copolymer comprised of alkyl acrylate and semifluorinated acrylate (50/50 mol %) were investigated. In the case of latex blends containing both semifluorinated polyacrylates and fluorine‐free or low‐fluorine polymers, self‐assembly accounted for enrichment of the perfluoroalkyl segments at the surface. Coatings exhibiting low surface energy and having a substantially reduced total fluorine content were obtained. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 360–367, 2003