紫外辐照法合成单分散钨酸纳米颗粒

通过紫外光照射柠檬酸钨氧配合物水溶液,制备了平均粒径约为20 nm的单分散钨酸纳米颗粒。红外光谱研究表明,柠檬酸钨氧配合物在紫外光照射下发生分解,形成柠檬酸和钨酸,而柠檬酸在钨酸的催化作用下发生光降解。XRD结果表明,单分散钨酸纳米颗粒是由WO₃·2H₂O和WO₃·H₂O组成的。此外,还考察了光照时间以及柠檬酸与钨酸钠的物质的量之比(n_cit/n_st)对产物结构和形貌的影响。随着光照时间延长,产物中WO₃·2H₂O的含量降低而WO₃·H₂O含量升高,产物粒径增大且分布加宽;随着n_cit/n_st增加,产物中WO₃·2H₂O含量增高,而WO₃·H₂O含量降低,且产物粒径变小而粒径分布变窄。     

(Zn，M)TiO3(M=Co，Ni，Co0.5Ni0.5)固溶体的溶胶-凝胶法合成

通过改进的溶胶-凝胶工艺在低温(800 ℃)下合成了基于钛酸锌(ZnTiO₃)体系的(Zn_1-xCo_x)TiO₃、(Zn_1-xNi_x)TiO₃和[Zn_1-x(Co_0.5Ni_0.5)_x]TiO₃陶瓷固溶体。采用X射线衍射分析(XRD)和差示扫描量热法(DSC)等测量技术对产物进行了物相和热稳定性分析。XRD结果表明，获得单一六方相(Zn_1-xCo_x)TiO₃、(Zn_1-xNi_x)TiO₃和[Zn_1-x(Co_0.5Ni_0.5)_x]TiO₃时各自的固溶稳定区间为0.5 ≤ x ≤ 1.0, 0.9 ≤ x ≤ 1.0和0.8 ≤ x ≤ 1.0。与此同时，热分析结果证实，伴随钛酸锌基陶瓷体系掺杂钴量的增加，其六方相的热稳定性提高，且效果比掺杂镍更加显著。     

双杂原子Ti-V-β沸石的合成、表征及催化性能研究

以白炭黑(二氧化硅)为硅源、四乙基氢氧化铵为模板剂、硫酸钛为钛源、偏钒酸铵为钒源、氟化钠为矿化剂,采用水热法合成了Ti-V-β沸石。探讨了合成条件对Ti-V-β沸石形成的影响。运用XRD、IR、UV-Vis固体漫反射光谱、TG/DTA、SEM+EDS和ICP等测试技术对样品进行了表征并测定了样品中Ti和V的含量。结果表明,按下列化学组成配制初始反应混合物：n(SiO₂)∶n(V₂O₅)∶n(TiO₂)∶n[(TEA)₂O]∶n(H₂O)∶n(NaF)=60∶(0.05～1.2)∶(0.1～2.4)∶(12～18)∶(450～720)∶(4～14),可制备出Ti-V-β沸石,Ti和V原子进入了沸石骨架。对样品在以H₂O₂为氧化剂氧化苯乙烯反应中的催化活性作了初步考察,结果表明,Ti-V-β沸石具有很高的催化活性,在下列反应条件下：v(H₂O₂)/v(ph CH=CH₂)=2.6,V(acetone)/v(phCH=CH₂)=10,m(cat)/v(phCH=CH₂)=0.003 g·mL^-1,T=80 ℃,t=6 h,苯乙烯的转化率98.16%。产品的选择性为：苯甲醛68.15%,苯乙醛23.35%,苯乙酮6.61%。     

Ni-Fe/4A分子筛催化剂可控制备大内径碳纳米管

以乙醇为碳源,Ni-Fe/4A分子筛为催化剂,采用化学气相沉积法制备大内径碳纳米管(LIDCNTs)。研究了Ni/Fe的物质的量比(n_Ni∶n_Fe)、碳纳米管(CNTs)的制备温度、催化剂的煅烧温度和4A分子筛载体对CNTs内径的影响。采用TEM、SEM、XRD和BET对LIDCNTs和还原后的催化剂进行了分析。结果显示,LIDCNTs的内径随着CNTs的制备温度、催化剂的煅烧温度的升高和n_Ni∶<     

芴-硫芴共聚物的电子结构和光谱性质的理论研究

用DFT-B3LYP方法对低聚物(PF30T)_n [n(芴)∶n(硫芴)＝2∶1, 物质的量之比, n＝1～4], (PF50T)_n [n(芴)∶n(硫芴)＝1∶1, 物质的量之比, n＝1～4]体系全优化, 得到两系列低聚物的电离能(IP_(a,v))、电子亲和势(EA_(a,v))、空穴抽取能(HEP)、电子抽取能(EEP). 在此基础上用ZINDO和TD-DFT方法计算吸收光谱, 分析了两个系列的HOMO-LUMO能隙随着n递增的变化趋势及硫芴含量对低聚物电子结构和光谱性质的影响, 推断了高聚物的电子和光谱性质. 用ab initio CIS方法优化了低聚物的S₁激发态结构并分析了其与发射光谱的关系. 研究显示: 2,8位引入的硫芴基团, 破坏了链的共轭, 而且随着硫芴含量的增加, HOMO-LUMO能隙变大, 光谱蓝移; 激发态结构趋于共面化.     

Ni/Fe物质的量的比对Ni-Fe催化剂表面性质和二硝基甲苯加氢活性的影响

采用Fe粉置换氯化镍溶液中的Ni²⁺制备了Ni-Fe催化剂,并应用于催化二硝基甲苯加氢合成甲苯二胺的反应中。运用XRD、低温氮吸附-脱附、H₂-TPD、XPS和TEM等技术手段对不同Ni/Fe物质的量的比(n_Ni/n_Fe)下催化剂进行了表征。结果表明,n_Ni/n_Fe对Ni-Fe催化剂表面性质影响显著。当n_Ni/n_Fe为1:4时,Fe抑制Ni氧化的作用达到最大,Ni-Fe催化剂化学氢吸附量和活性物种Ni的分散度分别达到了0.16 mmol·g^-1和23%,催化剂性能得到较大的提升。在优化的催化剂制备条件下,DNT(二硝基甲苯)的转化率和TDA(甲苯二胺)的选择性分别达到了~100%和99%。另外,对Ni-Zn漆原镍(Urushibara Ni)催化剂和Ni-Fe催化剂催化DNT加氢反应进程进行了研究,发现它们有相同的加氢中间产物,但反应不同阶段的催化速率存在差异。     

Ni/Fe物质的量的比对Ni-Fe催化剂表面性质和二硝基甲苯加氢活性的影响

采用Fe粉置换氯化镍溶液中的Ni²⁺制备了Ni-Fe催化剂, 并应用于催化二硝基甲苯加氢合成甲苯二胺的反应中。运用XRD、低温氮吸附-脱附、H₂-TPD、XPS和TEM等技术手段对不同Ni/Fe物质的量的比(n_Ni/n_Fe)下催化剂进行了表征。结果表明, n_Ni/n_Fe对Ni-Fe催化剂表面性质影响显著。当n_Ni/n_Fe为1:4时, Fe抑制Ni氧化的作用达到最大, Ni-Fe催化剂化学氢吸附量和活性物种Ni的分散度分别达到了0.16 mmol·g^-1和23%, 催化剂性能得到较大的提升。在优化的催化剂制备条件下, DNT(二硝基甲苯)的转化率和TDA(甲苯二胺)的选择性分别达到了~100%和99%。另外, 对Ni-Zn漆原镍(Urushibara Ni)催化剂和Ni-Fe催化剂催化DNT加氢反应进程进行了研究, 发现它们有相同的加氢中间产物, 但反应不同阶段的催化速率存在差异。     

Al-Ni2P/SBA-15催化剂的制备、表征及加氢脱硫催化性能

以磷酸氢二铵为磷源,硝酸镍为镍源,硝酸铝为助剂铝源,制备了n_P/n_Ni=0.8,Al含量为1.06wt%~6.35wt%的一系列Al-Ni₂P/SBA-15催化剂。采用XRD、TEM和N₂吸脱附等技术对催化剂的结构进行了表征研究,以二苯并噻吩(DBT)作为模型化合物,在微型固定床反应器上对催化剂的加氢脱硫(HDS)性能进行了评价。结果表明,Al修饰的Al-Ni₂P/SBA-15催化剂仍然保持介孔结构,当Al含量低于5.29wt%时,催化剂的物相主要是Ni₂P,当Al含量在5.29wt%-6.35wt%之间时,催化剂的物相为Ni₂P和Ni₁₂P₅。Al含量为4.24wt%的3-Al-Ni₂P/SBA-15催化剂具有最好的二苯并噻吩加氢脱硫催化活性,在反应温度为360 ℃,反应压力为3.0 MP的条件下,3-Al-Ni₂P/SBA-15催化剂对二苯并噻吩的转化率可达99.0%。     

制备高比表面积碳化硅的几种影响因素

采用溶胶凝胶法，以蔗糖和正硅酸乙酯(TEOS)为原料，草酸为TEOS水解的催化剂，制备均相碳化硅前驱体，在氩气氛和高温条件下(1 350～1 600 ℃)将碳化硅先驱体进行碳热还原，制备出高比表面积的SiC。考察了水/TEOS物质的量的比、碳/硅物质的量的比及镍盐等因素对碳化硅比表面积的影响。结果表明，当n_water/n_TEOS=7.5，n_C/n_Si=4时，适宜的镍催化剂(n_Ni/n_TEOS=0.005)，凝胶形成的时间最短，镍盐的加入可使碳热还原温度降低200 ℃。     

T型分子筛膜的合成、表征与渗透汽化性能

采用二次生长法,在不锈钢、α-Al₂O₃和莫来石多孔管状支撑体上分别合成了高渗透汽化性能的T型分子筛膜。考察了合成条件如合成时间、n(SiO₂)/n(Al₂O₃)、n(H₂O)/n(Al₂O₃)和硅源等对T型分子筛膜形成和分离性能的影响。通过XRD和SEM表征了膜的晶相和形貌。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.