·OH对聚二甲基硅氧烷乳液辐射效应的影响

通过凝胶和溶胶分析与分子量测定的方法,研究了不同体系下,"OH对PDMS乳液γ辐射效应的影响.结果表明,"OH不仅可引发聚二甲基硅氧烷的分子间交联,也能促进其降解.对于纯PDMS乳液,在所研究的剂量范围内,"OH对其辐射交联行为影响较小.但若体系中加入H2O2、KIO4和N2O这些提高"OH生成产额的添加剂时,"OH对PDMS的促降解作用会随着吸收剂量增加而表现更明显,导致凝胶含量与纯乳液辐照情况相比下降较多.即使加入交联剂-三羟甲基丙烷三甲基丙烯酸酯(TMPTMA),在过量的"OH存在下,当吸收剂量大于40kGy以上时,TMPTMA不仅没有提高交联度,反而会与"OH协同,使PDMS的凝胶含量下降更显著,同时产生更多的小分子聚合物,并使PDMS的平均分子量分布变窄.这可能是由于交联剂首先与"OH作用,形成的产物会加快PDMS的降解.     

脉冲辐解研究葛根素对自由基的清除活性

采用脉冲辐解技术, 研究了葛根素(puerarin, 一种异黄酮)对二氧化氮自由基(NO₂^•)、一氧化氮自由基(NO^•)和羟基自由基(OH^•)的清除活性. 葛根素与NO₂^•和NO^•反应产生的瞬态吸收峰都在340 nm, 该吸收峰归结为瞬态产物puerarin-4-O^•; 葛根素与OH^•反应产生了较宽的瞬态吸收光谱(300～750 nm), 该谱图归结为puerarin-2-O^•, puerarin-4-O^•和[puerarin-OH]^•瞬态吸收的叠加. 另外, 葛根素与NO₂^•, NO^•和OH^•反应的速率常数分别为2.6 × 108, 1.7 × 10⁸和3.9 × 10⁹ L·mol^-1·s^-1.     

Fe3+掺杂TiO2光催化降解聚乙烯薄膜的研究

以快速溶胶-凝胶法制备了纳米TiO₂光催化剂，并用Fe³⁺对其掺杂改性，在室温条件下, 用于固相光催化降解聚乙烯(PE)包装薄膜的研究. 对催化剂和薄膜进行了X衍射分析(XRD)、傅立叶红外光谱分析(FT-IR)、扫描电子显微镜(SEM)形貌观察. 结果表明， 60 W紫外光辐射240 h后， PE失重为8.43%, 锐钛矿型纳米TiO₂光催化剂使PE失重30.66%；用Fe³⁺掺杂后，0.5%Fe₂O3/TiO₂、1.0%Fe₂O₃/TiO₂和2.0%Fe₂O3/TiO₂分别使PE失重35.91%、20.72%和13.30%. 光催化剂加速了PE的失重，碳链的断裂和光氧化腐蚀，在薄膜表面形成大量的坑洞，降解产物中的小分子量的石蜡含量明显增高. Fe³⁺掺杂有一个最佳量， 0.5%Fe₂O3/TiO₂光催化降解PE的活性最高.     

355 nm光照下大气液相中HNO2与C6H5Cl的反应机理

利用瞬态吸收光谱技术进行了有氧、无氧条件下氯苯与亚硝酸水溶液的交叉反应机理研究，初步考察了这些瞬态物种的生长与衰减等行为, 并对其光解产物进行了GC/MS分析.研究表明，HNO₂在355 nm紫外光的照射下可产生•OH自由基, •OH和氯苯反应生成C₆H₅Cl•••OH，反应速率常数为（6.6～7.0）×10⁹ L•mol^-1•s^-1; 在有氧条件下C₆H₅Cl•••OH可氧化为C₆H₅Cl•••OHO2, 反应速率常数为(1.6 ± 0.2)×109 L•mol^-1•s^-1,然后进一步分解; C₆H₅Cl•••OH衰减或与亚硝酸等作用可形成多种含硝基的化合物或醌类物质.     

Criegee自由基CH2O2与H2O反应机理及动力学的理论研究

在6-311＋G(2d,2p)水平下, 采用密度泛函理论(DFT)的B3LYP方法, 研究了Criegee 自由基CH₂O₂与H₂O的反应. 结果表明反应存在三个通道: CH₂O₂＋H₂O®HOCH₂OOH (R1); CH₂O₂＋H₂O®HCO＋OH＋H₂O (R2); CH₂O₂＋H₂O®HCHO＋H₂O₂ (R3), 各通道的势垒高度分别为43.35, 85.30和125.85 kJ/mol. 298 K下主反应通道(R1)的经典过渡态理论(TST)与变分过渡态理论(CVT)的速率常数k^TST与k^CVT均为2.47×10^－17 cm³•molecule^－1•s^－1, 而经小曲率隧道效应模型(SCT)校正后的速率常数k^CVT/SCT为 5.22×10^－17 cm³•molecule^－1•s^－1. 另外, 还给出了200～2000 K 温度范围内拟合得到的速率常数随温度变化的三参数Arrhenius方程.     

NdCl3-CdCl2-HCl-H2O的相平衡及其固相化合物的研究

测定了四元系NdCl₃-CdCl₂-HCl-H₂O(298. 15 K) 的相平衡溶度数据, 绘制了相应的溶度图. 该四元系是由4个固相区CdCl₂•H₂O(原始盐)、9CdCl₂•NdCl₃•20H₂O、5CdCl₂•NdCl₃•13H₂O、NdCl₃•6H₂O(原始盐)组成的复杂体系. 用X射线粉末衍射及TG-DTG和荧光光谱对9CdCl₂•NdCl₃•20H₂O 和5CdCl₂•NdCl₃•13H₂O进行了研究. 荧光研究表明, 化合物9CdCl₂•NdCl₃•20H₂O具有微弱的荧光强度, 5CdCl₂•NdCl₃•13H₂O的荧光强度则相对大于9CdCl₂•NdCl₃•20H₂O的. 对X射线粉末衍射进行了指标化.     

羟自由基对支撑磷脂双层膜的破坏及水溶性抗氧化剂保护作用的电化学研究

以支撑磷脂双层膜(supported bilayer lipid membrane, s-BLM)作为生物膜模型, 利用Fenton体系产生羟自由基(hydroxyl free radical, •OH), 采用循环伏安法研究了s-BLM与•OH之间的相互作用. 结果表明: •OH通过与磷脂发生化学反应, 诱发s-BLM上形成孔洞或缺陷, 这种作用对时间、FeSO₄和H₂O₂的浓度具有依赖性, 且不可恢复. 具有还原性基团的抗氧化剂维生素C, 还原型谷胱甘肽和L-半胱氨酸, 通过与•OH发生氧化还原反应, 可抑制•OH与s-BLM的相互作用, 降低•OH对s-BLM结构的破坏程度.     

稀有三环核苷衍生物单电子氧化反应的脉冲辐解研究

运用纳秒级脉冲辐解技术研究了稀有三环核苷衍生物6-甲基三环鸟苷(dYt)与一些单电子氧化性自由基的反应, 表征了反应过程中产生的阳离子自由基dYt^•+及其脱质子中性自由基dYt(-H)^• 的瞬态吸收光谱及pKa, 并首次得到该化合物与^• OH自由基及单电子氧化性自由基SO₄^•-, CO₃^•-, N₃^•反应的动力学速率常数, 揭示了反应机理, 为进一步了解该类化合物的氧化反应提供了一定的证据.     

355 nm光照下联苯与HNO2的交叉反应机理

利用激光闪光光解瞬态吸收光谱及气相色谱-质谱联用(GC-MS)技术分别对HNO₂与联苯水溶液经紫外光照射后发生的交叉反应的机理及最终产物进行了研究. 结果表明, HNO₂受355 nm紫外光激发产生的•OH能够快速加合至联苯的苯环上形成Bp-OH加合物, 其二级反应速率常数为9.5×10⁹ L·mol^-1·s^-1. 从动力学角度验证该加合物能够与H+发生反应, 亦可被HNO₂氧化为亚硝基联苯酚. 故大气水体中的HNO₂与联苯在紫外光照射下发生的交叉反应可能是环境中硝基化合物的来源之一.     

质子导体(Ce0.8La0.2)1－xCaxO2－δ 在合成氨中的应用

利用溶胶-凝胶法合成了萤石型稀土复合氧化物(Ce_0.8La_0.2)_1－xCa_xO_2－δ, 利用XRD、TEM和SEM对样品进行表征. 电化学方法研究表明, 合成样品在400～800 ℃温度范围内具有质子导电特性. 将(Ce_0.8La_0.2)_1－xCa_xO>_2－δ高温烧结体用于固态质子传导电池, 在常压下以氮气和氢气为原料合成氨气, 并确定了合成氨的适宜条件. 650 ℃时Ce_0.8La_0.2O_2－δ和(Ce_0.8La_0.2)_0.975Ca_0.025O_2－δ对应的氨产率分别达7.2×10^－9和7.5×10^－9 mol•s^－9•cm^－9.     

A STUDY ON RADIATION CROSSLINKING OFPOLYDIMETHYLSILOXANE （PDMS） RUBBER LATEX

Polydimethylsiloxane (PDMS) rubber latex with two sorts of sensitizers, trimethylol propane tri-methacrylate (TMPTMA) and diethylene glycol di-acrylate (DEGDA), was irradiated with y-rays and electron beams in various conditions. The radiation crosslinking reaction of PDMS occurs in the inner phase of the latex and is relatively isolated from the water phase. Therefore the oxygen and the radicals produced by the radiolysis reaction of water almost have no effect on the crosslinking reaction of polymer. The experimental data correspond with the Charlesby-Pinner relationship in the main. The gelation doses, degree of crosslinking and degradation as well as G values of crosslinking were calculated. From them, the sensitization coefficients were derived to offer a quantitative measurement of the enhancing effect of sensitizer on the radiation crosslinking.     

Radiation preparation and swelling behavior of sodium carboxymethyl cellulose hydrogels

Sodium carboxymethyl cellulose (CMC) is a kind of degraded polymer under γ-irradiation. However, in this work, it has been found that CMC crosslinks partially to form hydrogel by radiation technique at more than 20% CMC aqueous solution. The gel fraction increases with the dose. The crosslinking reaction of CMC is promoted in the presence of N₂ or N₂O due to the increase of free radicals on CMC backbone, but gel fraction of CMC hydrogel is not high (<40%). Some important values related to this kind of new CMC hydrogel synthesized under different conditions, such as radiation yield of crosslinking G(x), gelation dose R_g, number average molecular weight of network M_c were calculated according to the Charlesby–Pinner equation. The results indicated that although crosslinked CMC hydrogel could be prepared by radiation method, the rate of radiation degradation of CMC was faster than that of radiation crosslinking due to the character of CMC itself. Swelling dynamics of CMC hydrogel and its swelling behavior at different conditions, such as acidic, basic, inorganic salt as well as temperature were also investigated. Strong acidity, strong basicity, small amount of inorganic salts and lower temperature can reduce swelling ratio.     

Effect of gamma irradiation on ethylene–octene copolymers

Two ethylene–octene copolymers (POE) were irradiated with ⁶⁰Co gamma radiation and influence of irradiation atmosphere, absorbed dose and heat treatment of samples on the crosslinking were studied. Thermal properties and crystalline morphology of non-irradiated and irradiated POE were determined by using differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXS), respectively. The Charlesby–Pinner equation was used to describe the relationship between absorbed dose and sol fraction. The gel fraction of irradiated POE was lower and decreased with the increase of octene content when irradiated in oxygen, compared to irradiation in nitrogen atmosphere. The gel fraction increased significantly with the increasing of absorbed dose for the two copolymers. Heat treatment of samples prohibited the crosslinking of irradiated POE. The DSC results indicated that a subtle change of thermal properties of POE was observed before and after gamma irradiation at low dose. No change was found from the WAXS spectra of non-irradiated and irradiated POE. For heat-treating samples, the Charlesby–Pinner equation can not fit perfectly with the relationship between the sol fraction and absorbed dose, but it fits well with the crosslinking reaction of POE pellets.     

Effect of kappa-carrageenan on the properties of poly(N-vinyl pyrrolidone)/kappa-carrageenan blend hydrogel synthesized by γ-radiation technology

A series of hydrogels in the form of rods were prepared from kappa-carrageenan (KC) and poly (N-vinyl pyrrolidone) (PVP) by gamma radiation with ⁶⁰Co γ source at room temperature. The properties of the prepared hydrogels, such as the gel strength, gel fraction and swelling behavior were investigated. Incorporation of KC into the PVP/water system increased obviously the gel strength and equilibrium degree of swelling (EDS) of PVP hydrogel. The experimental analyses showed that the crosslinking reaction of PVP was quicker than the degradation of KC at a low dose (less than 30 kGy), and the degradation of KC was inhibited in the PVP/KC mixture system. So an interpenetrating polymer network (IPN) hydrogel composed of PVP (a chemical crosslinking network) and KC (a physical crosslinking network) was proposed here. The existence of different classes of water in this IPN system was shown by water melting curves using DCS.     

聚乙烯醇的强化辐射交联

通常γ-辐照裂解的聚乙烯醇(PVA)在N·N’-甲基丙烯酰胺(BAM)存在下可以辐射交联。BAM/PVA体系的辐射效应可大致依辐照剂量的增加划分为三个阶段:强化辐射交联为主区,强化辐射交联与辐射裂解相抵区和辐射裂解优势区。强化辐射交联区的溶胶分数S与辐照剂量D的关系可表示为: S=(1 (1/(1-K))D_g~(2=K))-(D_g/(1-K))D~(1-K) =A-BR~(1-K)式中,D_g为凝胶化剂量;K是与BAM含量相关的常数。     

间规聚丙烯过氧化物在多官能团单体存在下的交联

过氧化物交联;交联动力学;间规聚丙烯过氧化物在多官能团单体存在下的交联     

Quantification of radiation induced crosslinking in a commercial, toughened silicone rubber, TR55 by H MQ-NMR

Radiation induced degradation in a commercial, filled silicone composite has been studied by SPME/GC-MS, DMA, DSC, swelling, and multiple quantum NMR. Analysis of volatile and semi-volatile species indicates degradation via decomposition of the peroxide curing catalyst and radiation induced backbiting reactions. DMA, swelling, and spin-echo NMR analysis indicate an increase in crosslink density of near 100% upon exposure to a cumulative dose of 250 kGray. Analysis of the sol fraction via Charlesby-Pinner analysis indicates a ratio of chain scission to crosslinking yields of 0.38, consistent with the dominance of the crosslinking observed by DMA, swelling and spin-echo NMR and the chain scissioning reactions observed by MS analysis. Multiple quantum NMR has revealed a bimodal distribution of residual dipolar couplings near 1 krad/s and 5 krad/s in an approximately 90:10 ratio, consistent with bulk network chains and chains associated with the filler surface. Upon exposure to radiation, the mean 〈Ω_d〉 for both domains and the width of both domains increased. The MQ-NMR analysis provided increased insight into the effects of ionizing radiation on the network structure of silicone polymers.     

Electron beam crosslinking of non-lead PVC formulations

PVC samples with lead-free and lead-base stabilizer, containing TMPTMA (trimethylolpropane trimethacrylate) as a crosslinker and DOP (2-ethylhexyl phthalate) as a plasticizer, were electron beam treated at different doses (2–200 kGy) and characterized to evaluate crosslinking and other several properties, as a continuation of our previously reported paper, where these PVC formulations, typical for wire and cable applications, underwent gamma irradiation. The PVC was formulated with two different stabilizing systems: Ca/Zn and dibasic lead phthalate for comparison, to use them as jackets for a 22 wire gage (AWG). Small samples of the jacketed wires were irradiated in an industrial Dynamitron electron accelerator for the corresponding doses, along with two dosimetric systems: radiochromic thin film and alanine pellets dosimeters. The maximum dose applied was decided as the crosslinking increased, until the gel content was stable. The dose of 200 kGy was the condition for the highest crosslinking, so most of the wire was irradiated at such dose. Chemical and mechanical evaluations were carried out to the irradiated wire. The results show that 200 kGy was too high dose for the materials, since an important degradation is observed for the Ca/Zn systems. Unfortunately, such dose affects basically to CaZn formulations, which showed much poorer performance than classical lead-containing compositions. The results also indicate that gel content is not the best way of deciding the optimum condition for irradiation.     

辐照交联聚甲基乙烯基硅氧烷的ESR谱研究

本文研究了GY-131医用级聚甲基乙烯基硅氧烷(PMVS)在辐照交联中的自由基产生和衰减的ESR潜,以及SiO₂填料对交联的影响。