不同形状TiO2纳米材料在耐NaCl溶液及微生物腐蚀中的应用

采用电沉积方法研究制备了分别含TiO2纳米球、TiO2纳米线和TiO2纳米管的一系列Ni-P-Cr基复合镀层的耐海水微生物腐蚀的新型复合材料.TiO2纳米材料的形貌采用TEM表征.以SEM、EDX测试技术研究了复合镀层的表面形貌和元素组成.并分别在质量分数为3.5%NaCl溶液及以硫酸盐还原菌(SRB)为腐蚀介质,应用极化曲线和电化学阻抗谱法(EIS)研究了各种复合镀层的耐蚀和抗菌性能.结果表明,含TiO2纳米管的Ni-P-Cr基复合镀层具有更优良的耐电解质及微生物腐蚀性能.     

双金属洋葱结构纳米Mo0.9W0.1S2的合成

0 引言 继碳富勒烯和碳纳米管的发现,1992年R.Tenne等首次在Nature上发表了具有类富勒烯和纳米管结构的WS_2,开创了非碳无机类富勒烯(Inorganic Fullerene-like,简称IF)纳米化合物研究的新领域。由于具有与富勒烯碳或碳纳米管相类似     

无机复合锂离子电池隔膜的制备及性能研究

用氧化铝(Al2O3)、硫酸钡(Ba SO4)、锆钛酸铅(PZT)、二氧化钛(Ti O2)、气相二氧化硅R202(RSi O2)、A380(ASi O2)和沉淀相二氧化硅(PSSi O2)7种无机纳米材料制备成分散液,在单向拉伸聚丙烯(PP)隔膜表面单面涂覆制备了复合隔膜.对复合隔膜的形貌、透气性及热稳定性进行了研究,并通过线性扫描曲线和不同倍率下电池充放电循环考察了复合隔膜对电解液的电化学稳定性和电池循环性能的影响.结果表明,7种复合隔膜与空白PP隔膜相比,在140℃下的热收缩率均减小1倍以上,表明其中无机纳米材料对PP隔膜的热收缩性能有很大改善.电池循环性能研究表明,这几种复合隔膜电池循环性能都有不同程度的提高,且在较高倍率下依旧可以发挥优势(ASi O2涂层复合隔膜除外).ASi O2涂层复合隔膜电池在2 C高倍率放电时容量快速衰减,其原因可能是ASi O2过大的比表面积增加了锂离子迁移的阻力.     

三元金属二硫化物纳米管的制备

1992年和 1 993年 ,Tenne等[1,2 ] 先后报道了具有类富勒烯和纳米管状结构的 WS2 和无机类富勒烯 Mo S2 .此后 ,无机类富勒烯化合物的制备与合成成为国内外学者的关注热点之一 .但采用化学方法制备纳米金属二硫化物时 ,多面体或洋葱状结构的 Mo S2 或 WS2 晶体的形成概率小 (这与碳的情况相似 ,也许通过扩展反应区内的温度梯度可以增加形成上述两种结构的可能性 [3] ) .另外 ,采用气固相反应制备洋葱状 WS2 的过程中 ,当每批次的量超过 1 5g时 ,无机类富勒烯 (IF)纳米颗粒的质量降低 ;同时 ,若滤筛中粉末厚度过大 ,相当大的凝聚团块开…     

油酸/PSt/TiO_2复合纳米微球的制备

纳米复合材料是近年来化学、物理及材料科学研究最活跃的领域之一 .有机 -无机复合纳米微球的制备和性能研究是这一研究领域的一个重要分支 .有机 -无机复合纳米微球兼有有机材料、无机材料和纳米材料的特性 ,特别是“球形”结构使其具有微观的“滚动”特性而倍受摩擦学工作者的青睐 .目前聚合物纳米微球的摩擦学性能研究已取得了重要进展 [1～ 4 ] .段标等 [3,5]认为聚合物微球的润滑机理是在摩擦过程中 ,微球进入摩擦表面 ,因其弹性和球形 ,而起到一定的滚动作用 ;高载荷下 ,微球变形并在摩擦表面形成聚合物润滑膜 .然而有关聚合物 /无机…     

聚集诱导发光有机小分子无机纳米复合材料的研究进展

有机-无机复合荧光纳米材料制备简便,生物相容性好,成像性能优异,在化学和生物传感、生物成像、催化及能源材料等领域受到很多关注.传统的荧光有机小分子与无机材料复合时,常发生荧光猝灭,而聚集诱导发光(Aggregation-InducedEmission,AIE)有机小分子在聚集态具有高发光量子产率,为有机-无机复合荧光纳米材料的研究提供了机遇.由于AIE有机小分子功能化的无机纳米材料独特的优点,人们对其设计、合成及应用进行了较多研究.综述了AIE有机小分子和多种类型的无机纳米结构(金属纳米颗粒、钙钛矿材料、层状材料、氧化物、硫化物等)复合材料的制备和应用的新进展,特别是在化学和生物传感、生物成像、药物输运、光热治疗、催化以及能源等领域的应用,并对其发展前景进行了展望.     

溶胶-凝胶法制备Polyme/MS/SiO2(M=Pb,Cd)复合纳米材料

采用溶胶-凝胶结合水热结晶技术,可成功把高聚物引入MS-SiO2网络结构,合成一种新型的有机-无机硫化物即Polymer/MS/SiO2(M=Pb,Cd)复合纳米材料,其中聚甲基丙烯酸甲酯或聚丙烯酰胺等高聚物的引入将有效地防止无机粒子团聚,控制粒子尺寸,前者还能形成核-壳结构复合粒子.作者还详细讨论了该复合纳米材料的热分析,结果表明,聚合物的存在提高了原有MS-SiO2(M=Pb,Cd)材料的热稳定性.     

二维纳米材料作为润滑油添加剂的研究进展[1]

二维纳米材料因其独特的分子结构和润滑性能而在摩擦学领域得到了广泛的研究。同一层内原子间的高强度和较低的层间剪切强度使其成为一种优异的减摩抗磨添加剂。本文分别从石墨烯类二维纳米材料、过渡金属二硫化物和其它的二维纳米材料三方面综述了二维纳米材料作为润滑油添加剂的摩擦学性能,阐述了二维纳米材料的摩擦机理,并指出二维纳米材料作为高性能润滑材料仍需解决的问题及未来的研究趋势。     

富勒烯-苯乙烯-顺丁烯二酸酐三元共聚物的摩擦学行为

水溶性;纳米微球;摩擦学性能;富勒烯-苯乙烯-顺丁烯二酸酐三元共聚物的摩擦学行为     

电沉积非晶态Ni-W-B/ZrO2复合镀层及其结构与性能

在含有二氧化锆的Ni-W-B电解液中，电沉积获得Ni-W-B/ZrO2复合镀层.用差示扫描量热分析(DSC)、X射线衍射(XRD)、扫描电子显微镜(SEM)和电化学技术较系统地研究了Ni-W-B/ZrO2复合镀层的电沉积、热处理过程，以及镀层的结构、表面形貌、显微硬度和耐腐蚀性能.结果表明, 复合镀层的质量组成为Ni 47.5％、W 40.9％、B 0.9％和ZrO2 10.7％. DSC和XRD结果清楚说明, 二氧化锆对基质Ni-W-B镀层的结构有明显影响, 使得复合镀层的非晶态结构特征更加明显 .复合镀层比Ni-W-B合金有更高的显微硬度, 呈现团粒状结构, 晶块之间不存在裂纹但晶界清晰可辨; 二氧化锆粒子分散于Ni-W-B基质镀层中. 400 ℃、1 h热处理后, Ni-W-B基质镀层中W向镀层表面偏析, 镀层呈现固溶体晶态结构特征, 表面形貌特征基本不变, 复合镀层的显微硬度进一步提高, 抗腐蚀性能增强, 但镀层表层中的二氧化锆粒子大量脱落.     

Electrochemical characteristics and interfacial contact resistance of Ni-P/TiN/PTFE coatings on Ti bipolar plates

The Ni-P/TiN/PTFE (poly tetra fluoroethylene) composite coatings were prepared by electroless plating method on Ti plate, which was used as bipolar plates of proton exchange membrane fuel cells (PEMFCs). The morphology, crystallographic texture, electrochemical corrosion, contact resistance, and hydrophobic property of the Ti bipolar plates with coatings were investigated. The results revealed that Ni-P/TiN/PTFE coating had a dense surface morphology, uniform distribution of composite particles. Ti with coating showed 0.48 μA cm² of corrosion current in the simulated solution of PEMFCs and 6 mΩ cm² of interfacial contact resistance (ICR). The hydrophobicity test showed that the coating interface was flat and the wetting angle was 112.4°. In conclusion, The Ni-P/TiN/PTFE composite coatings exhibit superior improvement in corrosion resistance, interface hydrophobicity, and conductivity to Ni-P, Ni-P/TiN, and Ni-P/PTFE coatings. The Ni-P/TiN/PTFE coating was suited for bipolar plate surface modification of bipolar plates.     

Evaluation of the corrosion resistance of electroless Ni-P and Ni-P composite coatings by electrochemical impedance spectroscopy

Electroless Ni-P composite coatings have gained a good deal of popularity and acceptance in recent years as they provide considerable improvement of desirable qualities such as hardness, wear, abrasion resistance, etc. The disagreement among researchers on the corrosion behaviour of these coatings warrants a thorough investigation. Among the various techniques available for the determination of corrosion resistance, electrochemical impedance spectroscopy (EIS) is considered to be superior as it provides not only an assessment of the corrosion resistance of different deposits but also enables the mechanistic pathway by which the deposits become corroded to be determined. The present investigation focuses on the evaluation of the corrosion resistance of electroless Ni-P and Ni-P-Si₃N₄, Ni-P-CeO₂ and Ni-P-TiO₂ composite coatings produced using an acidic hypophosphite-reduced electroless nickel bath, using EIS. The study makes evident that the same fundamental reaction is occurring on all the coatings of the present study but over a different effective area in each case. The charge transfer resistance of electroless Ni-P and Ni-P composite deposits are in the range 32,253–90,700 Ω cm², whereas the capacitances of these coatings are in the range 11–17 μF/cm². The improved corrosion resistance obtained for electroless Ni-P and Ni-P composite coatings is due to the enrichment of phosphorus on the electrode surface, which enables the preferential hydrolysis of phosphorus over that of nickel. The better corrosion resistance obtained for electroless Ni-P composite coatings can be ascribed to the decrease in the effective metallic area prone to corrosion. Among the three electroless Ni-P composite coatings, the corrosion resistance is in the following order: Ni-P-CeO₂=Ni-P-Si₃N₄>Ni-P-TiO₂. Electronic Publication     

On the formation of the interlayer between Ni-P coating and AZ33 magnesium alloy substrate by means of in situ SEM observation

Pre-treatment process is the key step for electroless plating. Once a suitable pre-treatment film is in place, the desired metals can be plated. In this paper, Ni-P coating was successfully prepared on AZ33 magnesium alloy with Mg（OH）2 pre-treatment film by electroless plating. To investigate the role of MgF2 in Ni-P coating, the deposition procedures between Mg（OH）2 pre-treatment film and Mg（OH）2-MgF2 pre-treatment film （a traditional process） were compared. The surface morphology variations of coatings were observed with scanning electron microscopy and the compositions were analyzed by energy dispersive spectrometry. The results showed that during the plating, both MgF2 and Ni-P deposited at the initial stage, and MgF2 distributed in the bottom of the coating, forming a transitional interlayer with Ni- P. According to the heat quench test, a poor adhesion of the coating mainly occurred between the MgF2 and Ni-P coating.     

Tribological behavior of polyurethane-based composite coating reinforced with TiO2 nanotubes

The unmodified and hexamethylene diisocyanate (HDI) modified TiO₂ nanotubes, were used for fabricating TiO₂ nanotubes (TiNTs)/polyurethane (PU) composite coating. The effects of applied load and sliding speed on the tribological behavior of the composite coating were investigated using a block-on-ring wear tester. Compared to the TiO₂ nanotubes filled PU composite coating, the HDI modified TiO₂ nanotubes (TiNTs-HDI) filled one had the lower friction coefficient and higher wear life under various applied loads and sliding speed. Scanning electron microscope (SEM) investigation showed that the TiNTs-HDI filled PU coating had smooth worn surface under given applied load and sliding speed, and a continuous and uniform transfer film formed on the surface of the counterpart ring, which helped to reduce the wear of the coating. The improvement in the tribological properties of TiNTs-HDI/PU composite coating might due to an improvement in interfacial adhesion between TiNTs and PU after HDI treatment. The strong interfacial coupling of the composite coating made TiNTs-HDI not easy to detach from the PU matrix, and prevented the rubbing-off of PU composite coating, accordingly improved the friction and wear properties of the composite coating.     

Ni-P化学镀反应速率及机理研究

通过镀层分析和析氢量测量得到Ni-P镀层的沉积速度和H2PO2的分解速度·以混合电位理论为基础，对Ni－P电极在不同组成饮液中的极化曲线进行分解得到以化学镀电流形式所表示的反应速率·将两种方法所得结果进行对照，确定H2PO2氧化时电子迁移数为1，并用原子红-电化学联合理论解释溶液PH对反应速率及化学镀效率的景响．     

Preparation and properties of Ni–Co–P/nano‐sized Si3N4 electroless composite coatings

Ni–Co–P/nano‐sized Si₃N₄ composite coating was successfully fabricated on aluminum alloys by electroless plating in this work. The surface and cross‐sectional morphologies, composition, microstructure, microhardness, friction and wear behavior of deposits were investigated with SEM, EDS, XRD, Vickers hardness and high‐speed reciprocating friction, respectively. It was found that a Ni–Co–P/nano‐sized Si₃N₄ composite coating on aluminum alloy substrate is uniform and compact. The existence of nano‐sized Si₃N₄ particles in the Ni–Co–P alloy matrix causes a rougher surface with a granular appearance, and increases the microhardness but decreases the friction coefficients and wear rate of electroless coatings. Meanwhile, the effects of heat treatment at 200, 300, 400 and 500 °C for 1 h on the hardness and tribological properties were researched. It is revealed that both of the microhardness and tribological properties of Ni–Co–P coatings and Ni–Co–P/Si₃N₄ composite coatings increase with the increase of heating temperature in the range of 200–400 °C, but show different behavior for the two coatings after annealing at 500 °C. Copyright © 2011 John Wiley & Sons, Ltd.     

Effect of 3-Amino-5-mercapto-1,2,4-triazole on Electroless Nickel Deposition

The effects of organic additive, 3-amino-5-mercapto-1,2,4-triazole （AMTA） on bath stability, deposition rate, reaction activation energy, and Ni-P coating composition in acidic electroless nickel plating were investigated. Polarization curve method and infrared reflection spectroscopy were used to analyze the mechanism of the effect of AMTA on electroless nickel deposition. It was observed that AMTA improved bath stability, decreased the deposition rate, and increased the reaction activation energy. It was also revealed that AMTA decreased the phosphorus content and increased the sulfur content in Ni-P coating. In addition, AMTA inhibited the anodic oxidation of hypophosphite and accelerated the cathodic reduction of Ni^2＋. Infrared reflection spectroscopy result indicates that AMTA was adsorbed on the surface of Ni-P and interacted with Ni^2＋ to form an AMTA-Ni^2＋ compound. On the basis of the results of this study, the mechanism of the effect of AMTA on electroless nickel deposition was deduced.     

Ni-P-TiO2化学复合镀层电极的乙醇电催化氧化

于Ni-P镀液添加TiO2颗粒,用化学镀法在黄铜基底上制备不同TiO2含量的Ni-P-TiO2复合镀层电极.采用循环伏安法、线性扫描法、计时电流和交流阻抗法测定Ni-P-TiO2/Cu电极的电化学性能.结果表明:常温下Ni-P-TiO2/Cu电极在碱性溶液中对乙醇氧化有很高的电催化活性;Ni-P-TiO2电极上乙醇的电催化氧化活性随镀层TiO2量的不同而异;镀液中TiO2含量为5 g.L-1时,所得电极的电催化乙醇氧化的活性最佳.     

Advances in the synthesis of inorganic nanotubes and fullerene-like nanoparticles

In analogy to graphite, nanoparticles of inorganic compounds with lamellar two-dimensional structure, such as MoS(2), are not stable against folding, and can adopt nanotubular and fullerene-like structures, nicknamed inorganic fullerenes or IF. Various applications for such nanomaterials were proposed. For instance, IF-WS(2) nanoparticles were shown to have beneficial effects as solid lubricants and as part of tribological surfaces. Further applications of IF for high-tensile-strength fibers, hydrogen storage, rechargeable batteries, catalysis, and in nanotechnology are being contemplated. This Minireview highlights some of the latest developments in the synthesis of inorganic nanotubes and fullerene-like structures. Some structural aspects and properties of IF, which are distinct from the bulk materials, are briefly discussed.     

Ti基化学镀Ni-P和Ni-P-Cg镀层晶化动力学

利用化学镀技术在Ti基体材料表面制备了Ni-P合金镀层和Ni-P-Cg复合镀层。利用SEM、XRD和EDS等分析了镀层的晶化过程,用差热分析仪研究了Ni-P合金镀层和复合镀层的晶化动力学,运用Ozawa、Freeman-Carroll、Achar和Coats-Redfern方法对非等温动力学数据进行了分析和比较。结果发现,复合镀层的特征温度T_m和晶化激活能E均高于Ni-P合金镀层,而热焓值｜ΔH｜却低于Ni-P镀层;计算出Ni-P合金镀层和Ni-P-Cg复合镀层晶化激活能分别为308.9 kJ·mol^-1和412.99 kJ·mol^-1、指前因子A分别为58.03 s^-1和77.84 s^-1,确定了Ni-P合金镀层和复合镀层晶化动力学方程。