DMA-80测汞仪直接测定固体样品中的汞

利用DMA-80测汞仪直接测定固体样品中的汞,采用升温加热直接进行热分解、金汞齐反应,采用长、短双检测池,可直接测定固体、液体样品,汞含量在0.n~600.0ng/g范围内的样品都能准确地测定,每个样品测定时间约为5min。测定结果证明方法具有可靠性。     

隐丹参酮的电化学行为及其测定

采用循环伏安法研究隐丹参酮在电极上的电化学行为及建立差示脉冲伏安对其测定的新方法。在pH 4.0乙酸盐缓冲液中,氧化峰电流与隐丹参酮浓度在3.0×10-8~2.0×10-7mol/L范围内呈良好的线性关系,检出限为2.0×10-9mol/L。玻碳电极可有效消除样品中其它组分对隐丹参酮测定的干扰,已用于实际样品中隐丹参酮的直接测定。该方法灵敏度高、检测范围宽。     

中成药中微量汞的流动注射-冷原子吸收测定方法研究

研究了流动注射氢化物发生-原子吸收光谱法测定微量汞时的最佳条件,建立了中成药中微量汞的流动注射.冷原子吸收光谱分析方法。测定中成药中汞的检出限为2.7×10-9,线性范围0-60μg·L-1,相对标准偏差小于5％,加标回收率为95％-98％。方法操作简便、快速、灵敏、自动化程度高,应用于实际中成药样品中微量汞的测定,结果满意。     

银离子选择电极测定矿石中的银

用银离子选择电极测定矿石中的银,文献采用氢溴酸-硫酸蒸煮冒烟的办法消除汞的影响,效果较好。但是,当Ag~+浓度大于10~(-)M时,该方法使测定结果显著偏低。本文试用络合能力较强的乙二胺做为测定银时的离子强度调节剂,操作简便、方法重现性较好。用标准加入法,测定范围为5×10~(-6)～5×10~(-5)M Ag~+;如果用标准样品的pC_(Ag)~+定位,再测量待测样品的pX_(Ag)~+,测定范围为5×10~(-7)～5×10~(-5)M Ag~+。     

活性炭富集测定天然水中超痕量汞

天然水中汞含量极低,即使采用十分灵敏的定量技术,也需经较大倍数的富集才可准确测定.活性炭对汞吸附力极强,能从锌盐或金盐溶液中定量吸附低达1×10~（-9）g·L~(-1)的汞.在前文工作基础之上,我们进一步研究了汞在活性炭上的吸附行为和解吸附条件,建立了一种定量富集水中超痕量汞的技术,用于河水等实际样品测定,获得了满意结果.     

离子交换伏安法同时测定水体中的镉、汞

报道了一种同时快速测定水体中痕量镉、汞的电分析方法。在 p H 4.0 0的磷酸盐缓冲溶液中 ,镉、汞在钠型蒙脱石修饰玻碳电极上通过离子交换富集 ,获得一个灵敏的阳极溶出峰 ,由此可同时测定痕量的镉、汞离子。利用该方法测定镉、汞的线性范围分别为 8× 1 0 - 9到 2× 1 0 - 6 mol/L和 4× 1 0 - 8到 7.5× 1 0 - 6 mol/L ,检出限分别是1× 1 0 - 9mol/L和 8× 1 0 - 9mol/L。该方法简便、快速 ,灵敏度高。用此修饰电极测定了水样中的镉、汞离子 ,结果令人满意     

直接测汞仪快速测定鱼粉中的汞含量

建立了直接测汞仪快速测定鱼粉中汞含量的方法,通过热分解-金汞齐反应-冷原子吸收光谱进行总汞分析,无需进行样品前处理。鱼粉中汞含量的测定是根据国标GB/T13081-1991方法,样品需要进行酸消解,在强酸中加还原剂将汞离子还原成元素汞,采用"冷原子吸收法"进行测定,其前处理需消耗大量的试剂,消化回流时间长、易损失。比较了两种方法测定的结果,发现无显著性差异。该方法可直接测定鱼粉中汞的含量。     

催化裂解-金汞齐富集-冷原子吸收光谱仪测定土壤样品中总汞含量

为建立采用催化裂解-金汞齐富集-冷原子吸收光谱仪即直接测汞仪测定土壤样品中汞含量的方法,本研究配制汞总量为0~2 ng、0~15 ng和25~1023 ng的三种不同汞浓度系列的标准工作曲线,选取9个土壤样品,3种国家土壤有证标准物质,同一样品分别进行6组平行测定,并抽取3个土壤样品进行3种不同浓度加标回收试验,以对其方法精密度和准确度进行论证。 结果显示：仪器信号值与Hg总量之间均呈良好的线性关系。根据仪器多次测定空白数据结果,按照称样量0.1 g计算,方法最小检出量为0.09 ng/g;平行测定结果相对标准偏差均小于10%,土壤标准物质测定值与标准物质标准参考值均相符,不同浓度的加标回收率范围为78.4%～92.7%。结果表明催化裂解-金汞齐富集-冷原子吸收光谱仪,可用于批量土壤样品中汞含量的快速测定分析,方法的精密度和准确度可满足测定分析要求,且实验过程中无需前处理消煮,操作方便、快速高效。     

碳酸钙固硫固体进样测汞仪快速测定硫化铅精矿中汞

在使用固体进样测汞仪直接测定硫化铅精矿中汞时,由于试样中硫含量通常较高(高达30%以上),在测定过程中大量的硫被氧化会污染甚至腐蚀固体进样测汞仪的核心部件催化管,导致催化管寿命严重缩短。为解决该问题,建立碳酸钙固硫-固体进样测汞仪直接测定硫化铅精矿中汞的分析方法;并对Ca/S比,分解温度,分解时间,齐化时间等参数进行优化。在最优条件下,Hg的含量在2~20 ng和20~500ng线性范围内回归系数(R²)分别为0.9996和0.9998;方法检出限(LOD)为0.006 μg/g。用该法对3个典型样品进行测定,相对标准偏差RSD≤9%(n=7),加标回收率为96%~106%。该方法简单、快捷,准确度和精密度高,适合硫化铅精矿中汞的快速测定。     

玻碳电极阳极溶出法测定高纯铝中ppb级杂质镉铅铜

高纯铝中ppm级镉、铅、铜杂质的测定,现普遍采用悬汞电极或铂球镀银沾汞电极阳极溶出法测定。本文利用玻碳电极导电性好,灵敏度高和氢的超电势高等优点,与阳极溶出法连用,解决了在一般试验室中可靠的测定高纯铝中ppb级镉、铅、铜杂质的问题。试验证明方法的灵敏度,镉为3.6×10~(-9)M,     

Potentiometric stripping analysis for mercury

In potentiometric stripping analysis for mercury, elemental mercury is deposited on a glassy carbon electrode surface by means of potentiostatic reduction. It is then oxidized by potassium permanganate added to the sample prior to analysis and the “redox titration curve” thus obtained is recorded on a high-input impedance recorder. Deaeration of the sample is unnecessary. The analytical range is 5 × 10^-9–10^-3 M mercury(II), the times needed for potentiostatic accumulation ranging from 64 min at 10^-8 M to 1 min at concentrations above 10^-6 M. The chemistry of the stripping process is discussed and an automatic instrument for potentiometric stripping analysis is described.     

Sensitive and selective determination of mercury by differential pulse stripping voltammetry after accumulation of mercury vapour on a gold plated graphite electrode

 A selective and sensitive method is proposed for the determination of mercury by anodic stripping voltammetry after its preconcentration from the gas phase. Mercury from the sample solution is reduced to elemental Hg by SnCl₂ and volatilized by the bubbles of a carrier gas. The gas containing mercury vapour is dried and passed through a capillary onto a gold coated graphite electrode. An anodic stripping voltammogram is recorded from 0.1 mol/l HClO₄+3×10^-3 mol/l HCl solution. The calibration curve is linear from 1×10^-9 to 4×10^-8 mol/l Hg(NO₃)₂. The absolute detection limit is 0.46 ng Hg. The relative standard deviations for 4×10^-9 mol/l and 2×10^-8 mol/l Hg(NO₃)₂ are 9.8% and 6.1%, respectively (n=5). Received: 18 December 1995/Revised: 16 April 1996/Accepted: 20 April 1996     

Coulometric titration of sulphide with mercury(II) in an ammoniacal buffer

An accurate method is described for the coulometric titration of low sulphide concentrations (8 × 10^?5–8 × 10^?3 M) with mercury(II) in a pH 9 ammoniacal buffer at room temperature. The electrochemical reactions involved are explained. Cyanide does not interfere at cyanide/sulphide ratios below 3. Accurate precise results were obtained for a lithopone sample.     

A new fully automated on-line digestion system for ultra trace analysis of mercury in natural waters by means of FI-CV-AFS

A fully automated flow injection (FI) system utilizing the extraordinary oxidation power of bromine monochloride (BrCl) for the transformation of dissolved mercury species to Hg(2+) and oxidation of dissolved organic carbon (DOC) has been developed and coupled to cold vapor (CV) atomic fluorescence spectrometry (AFS) for highly sensitive mercury detection. The system can be applied to natural waters, sea water as well as freshwater and provides a detection limit as low as 16 pg Hg l(-1) from a sample volume of 7 ml. The relative standard deviation is about 4-10%. A 3-fold measurement of one sample is completely processed within 15 min. Dissolved organic carbon, chloride and iodide ions are tolerated in concentrations of 15 mg DOC l(-1), >21 g Cl(-)l(-1), and 10 mg I(-)l(-1). Validation of the proposed method yielded a good recovery of total mercury in a moorland water sample and in the certified reference material ORMS-3, river water. Investigation of eight real water samples with mercury concentrations in the range of 0.3-1.4 ng l(-1) also confirmed the suitability of the proposed method.     

Determination of caprolactam by adsorptive voltammetry after separation by thin-layer chromatography

Caprolactam (2-oxohexamethyleneimine) can be determined in wastewaters and natural waters by adsorptive stripping voltammetry after separation of the product of the reaction between caprolactam and p-(N,N-dimethylamino)benzene-p′-azobenzoyl chloride. When a hanging mercury drop electrode is used with an accumulation time of 60 s in stirred solution, caprolactam can be determined from a lower limit of 0.2 μg ml^?1. With a 360-s accumulation time, linear calibration plots are obtained for 8 × 10^?10?8 × 10^?9 mol l^?1 caprolactam. The effect of interfering sample components is eliminated by the TLC separation.     

Polarographic determination of fluoride using the adsorption wave of the Ce(III)-alizarin complexone-fluoride complex

A very sensitive electrochemical method for trace measurement of fluoride in water is discussed. The complex of cerium(III) with alizarin complexone (ALC) and fluoride ion is adsorbed at the dropping mercury electrode. In cathodic sweeps, the peak height is directly proportional to the concentration of fluoride over the range 8 x 10(-8)-5 x 10(-6)M (1.5 x 10(-9)-9.5 x 10(-8) g/ml), and the detection limit is 5 x 10(-8)M (9.5 x 10(-10) g/ml). The proposed method was applied to the determination of fluoride in water.     

Trace determination of lanthanum,cerium, and praseodymium based on adsorptive stripping voltammetry

A sensitive stripping procedure is described for quantifying lanthanum, cerium and praseodymium ions, based on the controlled adsorptive accumulation of the lanthanide/o- cresolphthalexon complex onto the static mercury drop electrode. The effect of various operational parameters on the stripping response is discussed. A 20-min accumulation period coupled with differential pulse measurement of the current resulting from the adsorbed complex permits quantitation down to the 1 × 10^?10 M level. For concentrations ranging from 2.5 × 10^?8 M to 2.5 × 10^?9 M, a 0.5- to 4-min accumulation period is sufficient. The relative standard deviation ar the 7 × 10^?8 M level ranges from 1 to 6%.     

富镉离子CdS量子点电化学发光法检测L-半脐氨酸

采用一锅法,通过控制镉硫比合成了表面富镉离子的硫化镉量子点,利用L-半胱氨酸可与量子点表面Cd2+结合,使量子点表面钝化,从而增强其电化学发光信号的性质,实现了对L-半胱氨酸的选择性检测.对合成的量子点进行了表征,优化了检测条件.在优化的条件下,L-半胱氨酸在5.0×10-9~1.0×10-5 mol/L浓度范围内与ECL信号呈良好的线性关系,检出限为1.2×10-9 mol/L(S/N=3).本方法对L-半胱氨酸具有良好的选择性,用于实际样品中L-半胱氨酸的测定,结果令人满意.     

Spectrophotometric determination of micro amounts of thiosulfate by liberation of thiocyanate from mercury(II) thiocyanate

The proposed determination of thiosulfate is based on the liberation of thiocyanate by the reaction of thiosulfate with mercury(II) thiocyanate and spectrophotometric determination of the thiocyanate with iron(III). The reaction of thiosulfate with mercury(II) thiocyanate is elucidated with reference to a system containing phosphate buffer; the phosphate is shown to participate directly in the reaction, and a balanced chemical equation is given. Optimum conditions are described for the stoichiometric formation of 3 mol of thiocyanate from 1 mol of thiosulfate. The method can be applied to the determination of thiosulfate in the range 3 × 10^?6–1.4 × 10^?4 M (1.7–78.5 μg thiosulfate in 5 ml).     

Direct determination of mercury in cosmetic samples by isotope dilution inductively coupled plasma mass spectrometry after dissolution with formic acid

A new method was proposed for the accurate determination of mercury in cosmetic samples based on isotopic dilution (ID)-photochemical vapor generation (PVG)-inductively coupled plasma mass spectrometry (ICP MS) measurement. Cosmetic samples were directly dissolved in formic acid solution and subsequently subjected to PVG for the reduction of mercury into vapor species following by ICP MS detection. Therefore, the risks of analyte contamination and loss were avoided. Highly enriched ²⁰¹Hg isotopic spike is added to cosmetics and the isotope ratios of ²⁰¹Hg/²⁰²Hg were measured for the quantitation of mercury. With ID calibration, the influences originating from sample matrixes for the determination of mercury in cosmetic samples have been efficiently eliminated. The effects of several experimental parameters, such as the concentration of the formic acid, and the flow rates of carrier gas and sample were investigated. The method provided good reproducibility and the detection limits were found to be 0.6 pg mL⁻¹. Finally, the developed method was successfully applied for the determination of mercury in six cosmetic samples and a spike test was performed to verify the accuracy of the method.