溴代烷烃与活性氮的反应发光研究

在流动余辉装置上, 利用N₂空心阴极放电制备活性氮, 研究了活性氮与溴代烷烃(CHBr₃、CH₂Br₂、C₂H₅Br、C₄H₉Br) 反应的化学发光.上述所有反应中, 在550～750 nm波段均观察到了较强的NBr (b¹Σ+→X³Σ^-)跃迁发射谱. 同时在活性氮与CHBr₃和CH₂Br₂的反应中, 在流动管下游还观察到了CN (A²π, B²π→X²Σ⁺)的发射谱. 验证性的实验表明, 激发态NBr (b¹Σ⁺)是由二步过程形成: N(⁴S)与溴代烷烃反应生成NBr (X³Σ^-), 再通过N₂ (A ³Σ_u⁺)分子能量转移到激发态NBr (b¹Σ⁺); 而激发态的CN是通过N(⁴S) + CBr→CN(A, B) + Br过程形成的.     

不同温度下VUV光激发的Pr3+离子的发光性质

The luminescent properties of Pr³⁺-doped LaB₃O₆, SrAl₁₂O₁₉, SrB₄O₇ and NaYF₄ in the vaccum ultraviol-et (VUV) range at different temperatures were investigated under the excitation of high-energetic synchrotron radiation. For Pr³⁺ ions in LaB₃O₆, SrAl₁₂O₁₉ and SrB₄O₇, only the parity-forbidden ¹S₀→4f² transitions were observ-ed in the emission spectra at relatively low temperature; but the parity-allowed 4f5d→4f² transitions appeared simultaneously when the temperature was high enough. And the intensity of broad 4f5d→4f² emission increased relative to the intensity of ¹S₀→4f² emissions with increasing temperature. Then the thermal equilibrium model of energy levels was employed to the lowest 4f5d state and ¹S₀ state of Pr³⁺ in the three hosts. The calculated curves were in good agreement with the experimental values, indicating the occurrence of the thermal excitation from ¹S₀ state to 4f5d states at high temperatures when the lowest 4f5d state lies higher than ¹S₀ state and the photon energy is high enough.     

Ni-Co双金属催化剂上沼气重整制氢机理

用传统湿式浸渍法制备了La₂O₃掺杂的商业γ-Al₂O₃负载的沼气重整催化剂Ni-Co/La₂O₃-γ-Al₂O₃, 并用程序升温加氢(TPH)、程序升温氧化(TPO)、程序升温表面反应(TPSR)、程序升温脱附(TPD)及脉冲实验对催化剂进行了表征. 结果表明, 沼气重整过程中Ni-Co/La₂O₃-γ-Al₂O₃催化剂上的表面碳物种主要来源于CH₄的裂解, CO₂的贡献很小. CH₄裂解能够产生三种活性不同的碳物种, 即C_α、C_β与C_γ. 随着反应的进行, C_α物种减小而C_β与C_γ物种增加, 且C_γ物种能够转变为惰性的石墨碳. 重整反应过程中CH₄与CO₂的活化能相互促进. 催化剂表面的O物种与C反应生成CO或与CH_x反应生成CH_xO再分解为CO与吸附态的H物种, 可能是Ni-Co/La₂O₃-γ-Al₂O₃催化剂上沼气重整的速率控制步骤.     

Tm3+/Er3+/Ho3+共掺SiO2-Bi2O3-AlF3-BaF2玻璃发光性能

采用高温熔融法制备了Tm³⁺/Er³⁺/Ho³⁺共掺的铋硅酸盐50SiO₂-40Bi₂O₃-5AlF₃-5BaF₂玻璃。研究了在808 nm激光器（Laser Diode）激发下Tm³⁺/Er³⁺/Ho³⁺共掺的铋硅酸盐在2 060 nm处的发光性能,同时测试及分析了该铋硅酸盐玻璃的差热特性、吸收光谱及荧光光谱。根据吸收光谱以及Judd-Oflet理论,计算了Ho³⁺的Judd-Oflet强度参数Ω_t（t=2,4,6）以及Tm³⁺/Er³⁺/Ho³⁺相应的吸收截面。铋硅酸盐玻璃中,Tm₂O₃、Er₂O₃和Ho2O3掺杂浓度分别为0.75%、1.0%和0.5%时,2 060 nm处Ho³⁺∶⁵I₇→⁵I₈发射峰强度达到最大。对Tm³⁺/Er³⁺/Ho³⁺ 3种离子的光谱性质和离子间可能存在的能量传递也做了分析。Ho³⁺在1 953 nm处的最大吸收截面σ_abs为9.08×10^-21 cm²,在2 060 nm处的最大发射截面σem为11.68×10^-21 cm²,辐射寿命τ_mea为2.75 ms,具有良好的增益效应σ_emτ（3.212×10^-20 cm^-2·ms）。     

新半金属Fe2LaO4磁电性能的第一性原理计算

利用基于密度泛函理论的第一性原理赝势法设计并优化了含稀土元素的新半金属Fe₂LaO₄。详细计算了其电荷分布,分子磁矩等磁电性能，并结合配位场理论分析了其电子结构。结果表明，Fe₂LaO₄是一种含稀土元素的铁磁性的新ⅡB型半金属；它的稳定相晶格常数约为0.623 nm，分子磁矩约为1.0μ_B；Fe₂LaO₄属软铁磁性半金属；La较多的外层电子增强了Fe₂LaO₄内部的库仑斥力,导致了配合物ML₄和ML₆均受强场作用,从而使Fe₂LaO₄具有软铁磁性；考虑自旋分布后ML₄和ML₆的电子结构分别为a_1g¹↑a_1g¹↓t_1u³↑t_1u³↓e_g²↑e_g²↓t_2g³↑t_2g³↓和a_1g¹↑a_1g¹↓t_1u³↑t_1u³↓t_2g³↑t_2g³↓e_g²↑e_g²↓e_g^*1↑,这些电子属于分子轨道。     

红色长余辉荧光粉Ca2Zn4Ti16O38:Pr3+的水热辅助合成及发光性质

采用水热法辅助合成了纯相Ca₂Zn₄Ti₁₆O₃₈:Pr³⁺荧光粉,初始n_Ca:n_Zn:n_Ti=2:4.1:15,煅烧条件为1 050 ℃空气气氛烧结5 h.并以X射线衍射、扫描电镜、紫外可见漫反射光谱和荧光光谱表征了样品的物相组成、微观形貌和光谱性质.合成的荧光粉在高温煅烧后仍较好地保持了球形的微观形态,优化的Pr³⁺掺杂浓度为0.015.Ca₂Zn₄Ti₁₆O₃₈:Pr³⁺荧光粉在471 nm波长激发下发射红光,发射谱通过高斯分峰拟合得到位于605、620和645 nm的3个发射峰,分别对应于Pr³⁺的¹D₂→³H₄,³P₀→³H₆和³P₀→³F₂跃迁.在471 nm波长激发下,Ca₂Zn₄Ti₁₆O₃₈:Pr³⁺的614 nm红光发射表现出超长余辉特性,表明该荧光粉是一种能被可见光有效激发的红色长余辉荧光粉.     

白光LED用Sr0.955Al2Si2-xTixO8：Eu2+荧光粉的晶体结构和光谱特性

由高温固相反应制得Sr_0.955Al₂Si_2-xTi_xO₈：Eu²⁺（x=0~1.0）系列试样,研究了Ti⁴⁺置换Si⁴⁺对其晶体结构和光谱特性的影响。Ti⁴⁺以类质同相替代Si⁴⁺进入晶体晶格中,形成了连续固溶体,其晶胞参数a,b,c,β和晶胞体积V随Ti⁴⁺置换量呈线性递增。Ti⁴⁺置换Si⁴⁺对晶胞参数c的影响显著,b其次,a最小。荧光激发谱为宽带,位于230~400nm,由267nm、305nm、350nm和375nm 4个峰拟合成,表观峰值位于351nm;随着Ti⁴⁺置换量的增加,半高宽（FWHM）从105nm减小到93nm。发射光谱位于380~600nm,表观峰值位于407nm,可由406nm和441nm两峰拟合而成并且随Ti⁴⁺置换量增加线性红移,Ti⁴⁺进入晶格对长波长发射中心影响较少;Ti⁴⁺置换量为1.0时,表观发射峰位从407nm红移至417nm;利用试样荧光光谱和VanUitert经验公式,得出SrAl₂Si₂O₈：Eu²⁺中Sr²⁺的配位数为9。随着Ti⁴⁺置换量Si⁴⁺进入基质晶格,造成Eu-O距离变小,使得Eu²⁺所处的晶体场强度增强,发光中心Eu²⁺的5d能级分裂增大,造成Eu²⁺最低发射能级重心下移,两拟合谱峰峰位均呈线性红移。     

掺镍型层状LixNiyMn1-yO2正极材料的合成与电性能研究

A kind of cathode material of layered Li_xNi_yMn_1-yO₂ characterized with the O2 type has been synthesized by a simple method. Its precursor Na_xNi_yMn_1-yO₂ has been prepared from manganese dioxide， nickel hydroxide and sodium carbonate at high temperature in air and quickly cooled in cold water， then it has been exchanged by the melted LiNO₃ at 300～400℃ in air. The effects of calcine-temperature for the precursors and its compositions (the content of Na and Ni) on the electrochemical properties of the material Li_xNi_yMn_1-yO₂ have been investingated by XRD and electrochemical tests. The results show that the sample Li_0.7Ni_0.3Mn_0.7O₂， has the best electrochemical properties which shows only one charge-discharge potential stage of 2.8～3.0V and has a high specific capacity over 180mAh·g^-1 cycled between 2.0～4.20V. A significant structure transformation to the spinal-type phase has not been found in the charge-discharge cycling and the discharge specific capacity around 165mAh·g^-1 has re-mained after the 20th cyclings for the material.     

C2H4在Fe3C(100)表面吸附及脱氢裂解的密度泛函理论研究

采用自旋极化密度泛函理论和周期平板模型,对C₂H₄在铁基费托合成催化剂活性相之一Fe₃C（100）表面从热力学和动力学两个方面分析了C₂H₄在Fe₃C（100）表面进行脱氢和裂解反应的竞争性。结果表明,C₂H₄在Fe₃C（100）表面的μ-bridging吸附比π、di-σ吸附更加稳定;C₂H₄与Fe₃C（100）面的相互作用导致C₂H₄的C原子部分发生重新杂化（sp²→sp³）,使C原子呈近四面体结构。在Fe₃C（100）表面C₂H₄易于发生脱氢反应,C-C键裂解反应不具有竞争性。亚乙烯基CCH₂和乙烯基CHCH₂是Fe₃C（100）表面最丰的C₂物种,或是C₂H₄参与链增长的主要单体形式。     

脉冲辐解研究葛根素对自由基的清除活性

采用脉冲辐解技术, 研究了葛根素(puerarin, 一种异黄酮)对二氧化氮自由基(NO₂^•)、一氧化氮自由基(NO^•)和羟基自由基(OH^•)的清除活性. 葛根素与NO₂^•和NO^•反应产生的瞬态吸收峰都在340 nm, 该吸收峰归结为瞬态产物puerarin-4-O^•; 葛根素与OH^•反应产生了较宽的瞬态吸收光谱(300～750 nm), 该谱图归结为puerarin-2-O^•, puerarin-4-O^•和[puerarin-OH]^•瞬态吸收的叠加. 另外, 葛根素与NO₂^•, NO^•和OH^•反应的速率常数分别为2.6 × 108, 1.7 × 10⁸和3.9 × 10⁹ L·mol^-1·s^-1.     

一种水溶性疏水缔合聚合物二临界缔合行为研究

对三元共聚疏水缔合聚合物（丙烯酰胺／十八烷基二甲基烯丙基氯化铵／苯乙烯）的临界缔合浓度进行研究,发现其具有二临界缔合现象以及其在二临界缔合浓度附近不同的耐温抗盐的流变行为。研究结果表明,该疏水缔合聚合物的第一临界缔合浓度（C1^＊）为500mg／L,第二临界缔合浓度（C2^＊）为2400mg／L;C2^＊附近聚合物溶液的耐温性能较差;抗盐性能表现出三种不同的情况：随着盐质量浓度的增加,C〈C1^＊时,溶液粘度下降;C1^＊〈C〈C2^＊时,溶液粘度先增加后下降;C〉C2^＊时,溶液粘度先快速增加,后缓慢增加,最后下降。     

Rheological behavior of silica suspensions in aqueous solutions of associating polymer

Associating polymers are hydrophilic long-chain molecules containing a small amount of hydrophobic groups. The aqueous solutions show viscoelastic responses above some critical concentrations because a three-dimensional structure is formed by association of hydrophobic groups. When the associating polymers are added to silica suspensions at low concentrations, the flocculation is induced by bridging mechanisms, and the flow of suspensions become shear-thinning. For suspensions prepared with polymer solutions in which the associating network is developed, the viscosity decreases, shows a minimum, and then increases with increasing particle concentration. The viscosity decrease may arise from the breakdown of associating network due to adsorption of polymer chains onto the silica surfaces. As the particle concentration is increased, the polymer concentration in solution is decreased, and finally, all polymer chains are adsorbed on the surfaces. Beyond this point, the partial coverage of particle surfaces takes place and strong interactions are generated between particles by polymer bridging. Since the stable suspensions are converted to highly flocculated systems, the viscosity is increased and the flow becomes shear-thinning. The concentration effect of silica particles on the viscosity behavior of suspensions can be explained by a combination of viscosity decrease in solution due to polymer adsorption and viscosity increase due to flocculation.     

自组装效应对AM/NVP共聚的影响

研究了丙烯酰胺(AM)与N-乙烯基吡咯烷酮(NVP)在水/四氢呋喃(THF)溶液中的自由基共聚。发现,当水溶液中含THF,AM的聚合速率下降,NVP的聚合速率提高。黏度测定发现,在THF质量分数为28%,AM/NVP物质的量比为5∶1的水/THF体系中,共聚物的黏度达到最大值,与该体系中NVP的聚合速率达到最大值相一致。溶液中加入氯化钠,AM的聚合速率提高,但随THF的含量增加而降低。加入尿素,在含水率达到较大值,NVP聚合速率最大。用透射电子显微镜(TEM)和核磁共振谱(NMR)对聚合物结构进行了表征。在水/THF中,共聚物链自组装形成"核―壳"状微聚体。NVP上的五元环聚集成"核"状,共聚物链的酰胺基团尽量舒展,形成"壳"状。溶剂的组成变化伴随"核―壳"状微聚体半径的改变,影响AM和NVP的聚合速率。     

十二烷基磺酸钠对丙烯酰胺－烯丙基磺酸钠共聚物溶液粘度的影响

丙烯酞胺-烯丙基磺酸钠共聚物(PASA)优良的絮凝性能已在前文^[1]中报道.本文主要考察阴离子表面活性剂R₁₂SO₃Na对其溶液粘度的影响,并与PAM做了对照.     

聚(丙烯酰胺-丙烯酸高级酯)的溶液性质研究

采用沉淀聚合法分别合成了丙烯酰胺与丙烯酸十四酯、丙烯酸十六酯、丙烯酸十八酯一系列疏水缔合型共聚物。对共聚物溶液性质及疏水基团浓度、电解质浓度、温度等因素对共聚物溶液性能的影响进行了研究,结果表明这类疏水缔合型聚合物表观出较好的耐温、耐盐等性能。     

Effect of ethanol on the interaction between poly(vinylpyrrolidone) and sodium dodecyl sulfate

The effect of ethanol on the interaction between the anionic surfactant sodium dodecyl sulfate (SDS) and the nonionic polymer poly(vinylpyrrolidone) (PVP) has been investigated using a range of techniques including surface tension, fluorescence, electron paramagnetic resonance (EPR), small-angle neutron scattering (SANS), and viscosity. Surface tension and fluorescence studies show that the critical micelle concentration (cmc) of the surfactant decreases to a minimum value around 15 wt % ethanol; that is, it follows the cosurfactant effect. However, in the presence of PVP, the onset of the interaction, denoted cmc(1), between the surfactant and the polymer is considerably less dependent on ethanol concentration. The saturation point, cmc(2), however, reflects the behavior of the cmc in that it decreases upon addition of ethanol. This results in a decrease in the amount of surfactant bound to the polymer [C(bound) = cmc(2) - cmc] at saturation. The viscosity of simple PVP solutions depends on ethanol concentration, but since SANS studies show that ethanol has no effect on the polymer conformation, the changes observed in the viscosity reflect the viscosity of the background solvent. There are significant increases in bulk viscosity when the surfactant is added, and these have been correlated with the polymer conformation extracted from an analysis of the SANS data and with the amount of polymer adsorbed at the micelle surface. Competition between ethanol and PVP to occupy the surfactant headgroup region exists; at low ethanol concentration, the PVP displaces the ethanol and the PVP/SDS complex resembles that formed in the absence of the ethanol. At higher ethanol contents, the polymer does not bind to the ethanol-rich micelle surface.     

Studies on rheological behaviour of hydrophobically associating polyacrylamide with strong positive salinity sensitivity

Hydrophobically associating polymer has been obtained by homogeneous copolymerization of acrylamide and an anionic surface-active monomers (surfmer) of acrylamide-type, sodium 2-acrylamido-tetradecane sulfonate (NaAMC₁₄S) in aqueous solution, and under different concentration conditions of NaAMC₁₄S above its critical micellar concentration (CMC) and below CMC, two structure types of copolymers P (AM–NaAMC₁₄S) were prepared in which main chains NaAMC₁₄S were distributed in microblock and in random manner, respectively. The hydrophobically associating property and rheological behaviour of the copolymers were studied with viscosimetry and then by fluorescence probe method. It was found that the apparent viscosity of the aqueous solution of the copolymers with microblock structures exhibits strong positive salinity sensitivity, whereas the positive salinity sensitivity of the apparent viscosity of the aqueous solution of the copolymers with random structure only appears generally and the apparent viscosity was diminutively increased because of salinity-promoting hydrophobic association. For those copolymers with microblock structures, the apparent viscosities of their brine solution are much higher than that of their pure water solution. In CaCl₂ solution (2 wt%), as the copolymer concentration attains 0.2 wt%, the apparent viscosity enhances dramatically with the increase in concentrations, and as the copolymer concentration was 0.3 wt%, the apparent viscosity can enhance by almost two orders of magnitude (from 32 to 1,000 mPa·s) as compared with in pure water solution. Thus, for copolymer P (AM–NaAMC₁₄S) with microblock structure, the peculiar positive salinity sensitivity, i.e. salinity thickening, is displayed distinctly. The unusual positive salinity sensitivity of copolymers P (AM–NaAMC₁₄S) with microblock structure was also revealed by fluorescence probe method, and the value I ₁/I ₃ of pyrene in the brine solution of the copolymers was smaller than that in pure water solution of the copolymers. This unique salinity sensitivity is a reflection of the unusual microstructure of the copolymers. The experiment results are interpreted in terms of the effects of the surfmer distribution manner in the copolymer main chain and bonding way of the ionic surfmer to the copolymer main chain on the forming intermolecular association.     

聚二烯丙基甲基苄基氯化铵的合成及粘度行为

以甲胺、烯丙基氯、NaOH、氯化苄和偶氮二异丙基咪唑啉盐酸盐为原料,合成了聚二烯丙基甲基苄基氯化铵(PDAMABC),采用FT IR、1H NMR和元素分析对其结构进行表征,并考察了其在氯化钠、氯化钾、溴化钾、氯化钙、氯化镁、硫酸镁和硫酸钠溶液中的粘度行为。 将所得水相和低沸点馏分回用,二烯丙基甲基胺的收率从72.79%提高至83.41%;以水与乙醇为混合溶剂（V（H2O）∶V（C2H5OH）为1∶3~2∶3）,合成的二烯丙基甲基苄基氯化铵收率较高且水溶性好。 PDAMABC的比浓粘度随外加盐浓度增加而降低。 在0.1 mol/L NaCl溶液中,当其质量浓度低于0.031 25 g/L时,表现为聚电解质行为;质量浓度大于0.125 g/L时,表现为中性聚合物的粘度行为。 外加盐对比浓粘度的影响顺序为：Na2SO4＜NaCl＜KCl＜MgSO4＜MgCl2＜CaCl2＜KBr。 阴离子的屏蔽作用是导致比浓粘度降低的主要原因。     

Effect of borax additives on the rheological properties of sodium hyaluronate aqueous solutions

The rheological properties of sodium hyaluronate aqueous solutions are studied, and the effect of borax additives on them is investigated. It is shown that, at low concentrations, sodium hyaluronate behaves as a typical linear polyelectrolyte in the limit of a high concentration of the salt in both a 0.1 M NaCl aqueous solution and a salt-free solvent. The addition of 1 mole of borax per base-mole of the polymer to the solution of sodium hyaluronate significantly decreases the specific viscosity of the solution if no salt is added and has practically no effect on the viscosity of the solution in 0.1 M NaCl. The viscosity of a semidilute solution of sodium hyaluronate without the added salt decreases as the shear rate is increased in the range 1.5–656 s^?1. With an increase in temperature, viscosity decreases and its dependence on shear rate becomes less pronounced. The same effect is exerted by small amounts of borax. The properties of salt-free solutions are explained by the presence of admixtures of low-molecular-mass ions in them that screen the Coulomb repulsion of charges linked to sodium hyaluronate chains, and the effect of borax may be rationalized by the screening effect of ions resulting from the hydrolysis of borax.     

含辣素衍生结构疏水缔合聚合物PAAH的合成、表征及溶液性质

以辣素功能结构单体N-（4-羟基-3-甲氧基-苄基）-丙烯酰胺（HMBA）为疏水单体,与丙烯酰胺（AM）和2-丙烯酰胺基-2-甲基丙磺酸钠（NaAMPS）通过自由基胶束共聚,制得三元疏水缔合聚合物P（AM-NaAMPS-HMBA）（简称PAAH）. 采用紫外-可见光谱、核磁共振氢谱、热重分析及扫描电子显微镜对共聚物的结构及形貌进行表征,利用原子力显微镜对聚合物水溶液的微观形貌进行观察,并对其溶解性、疏水缔合性、耐温性及抑菌性能进行了研究. 结果表明,所得共聚物中疏水单体含量与投料比基本一致;PAAH具有良好的速溶性,当聚合物浓度超过一定值后,溶液黏度急剧增加,且随着疏水单体含量增加,疏水缔合性能增强;原子力显微镜观察证实了聚合物水溶液中网络结构的存在. 与未改性的P（AM-NaAMPS）（简称PAA）共聚物相比,引入具有生物活性且带有刚性苯环结构的HMBA单体可使PAAH共聚物热稳定性增强,耐温性能提高,并赋予其优良的抑菌性能.