Mn掺杂Ce0.7Zr0.3O2催化剂同时去除碳烟和氮氧化物的性能

采用柠檬酸络合燃烧法制备了一系列x%Mn/Ce0.7Zr0.3O2(x=0,5,10,15,30,50)复合金属氧化物催化剂,对其同时去除柴油机尾气中碳烟颗粒物(PM)和氮氧化物(NOx)反应的催化活性进行了评价,并采用XRD、低温氮吸附-脱附、H2-TPR、O2-TPD和原位漫反射红外光谱(in situ DRIFTS)等技术对催化剂的性能进行了表征。结果表明,不同含量Mn掺杂入铈锆固溶体中均形成了三元固溶体催化剂,在同时去除PM和NOx的催化反应中,固溶体催化剂的催化活性与其氧化能力直接相关。其中30%Mn/Ce0.7Zr0.3O2催化剂具有较好的同时去除PM和NOx的催化活性,催化去除PM的Ti和Tm分别为298和504℃,NO的转化率达到30.6%。结合O2-TPD和原位红外结果可知,30%Mn/Ce0.7Zr0.3O2表面吸附的超氧物种(O2-)及其与NO反应生成的硝酸盐物种(NO3-)是同时去除PM和NO反应的主要活性物种,进而指出PM和NO在30%Mn/Ce0.7Zr0.3O2表面反应过程中形成了异氰酸盐(-NCO)中间物种,在原位红外实验的基础上提出了30%Mn/Ce0.7Zr0.3O2复合氧化物催化剂同时去除PM和NOx的反应机理。     

镍促进CuO-CeO2催化剂的结构表征及低温CO氧化活性（英文）

制备了一系列CO低温氧化的Ce20Cu5NiyOx催化剂,并采用氮气低温物理吸附、X射线衍射、程序升温还原、X射线光电子能谱以及拉曼光谱等手段对催化剂进行表征.结果表明,Ce20Cu5Ni0.4Ox催化剂活性最高.NiO的添加可以使得较多的Cu物种掺杂到CeO2晶格中,通过形成铈镍固溶体产生更多的氧空位.表征结果显示,Ce20Cu5Ni0.4Ox催化剂中存在大量的Cu+,Ce3+及晶格氧,催化剂中的Cu+很容易进入到氧化铈晶格,形成Cu-O-Ce固溶体,从而增强了在还原气氛下晶格氧的释放能力.Ce20Cu5Ni0.4Ox催化剂高的催化活性主要归因于大量Cu+以及形成的Cu-O-Ce和Ni-O-Ce固溶体.     

限域纳米空间制备高效HCl氧化CuO-CeO_2催化剂

利用KIT-6的有序介孔作为限域空间制备了一系列的介孔Cu O-Ce O2催化剂.借助XRD、BET、Raman、ESEM、TEM和H2-TPR等手段对催化剂进行表征,并考察其在HCl氧化反应中的催化性能.结果表明:铜含量35%时,Cu O物种高度分散在催化剂的表面或者进入Ce O2晶格,催化剂具有高比表面积(140 m2·g-1)和较小的晶粒尺寸,其中25Cu O-Ce O2催化剂具备最高的表面氧空位浓度和最优的低温氧化还原性能,并在HCl氧化反应中表现出最佳的催化活性,O2/HCl=6,370℃时转化率达到90%.反应动力学结果表明,25Cu O-Ce O2中更多的高分散的Cu O促进了HCl在催化剂表面的吸附和活化,更高浓度的氧空位增强了氧分子的吸附和活化.     

A位离子掺杂种类对La_(0.7)M_(0.3)Ni_(0.7)Fe_(0.3)O_3(M=Pr,Y,Sr,Zr,Ce)催化性能的影响

以聚苯乙烯胶晶(PS)为模板剂,用共沉淀法分别制备了La0. 7M0. 3Ni0. 7Fe0. 3O3(M=Pr、Y、Sr、Zr和Ce)钙钛矿复合氧化物,以乙醇水蒸气重整反应为探针,探讨了A位离子掺杂种类对La0. 7M0. 3Ni0. 7Fe0. 3O3催化活性、选择性以及积碳性能的影响。结果表明,掺杂离子均能进入了La Ni0. 7Fe0. 3O3钙钛矿晶格中,掺杂离子种类影响其晶相结构,掺杂Ce离子的样品产生较多的晶格缺陷,表面结构疏松,孔道丰富,表面吸附较多的活性氧物种,比表面积和孔径均较大。A位掺杂后钙钛矿复合氧化物还原温度有所降低,同时掺杂种类影响金属中心的形成,掺杂Ce离子的样品在还原过程中产生较多的金属中心。乙醇重整制氢反应的活性和抗积碳性能取决于样品表面活性氧物种和还原过程中产生的金属中心,表面活性氧物种协同金属中心有利于提高钙钛矿复合氧化物的活性和稳定性。     

Pd/Ce0.8Zr0.15La0.05Oδ整体催化剂甲苯催化燃烧性能的研究

采用一次浸渍法分别制备了 Pd/Ce0.8Zr0.15La0.05Oδ及Pd/Ce0.8Zr0.2O2整体式蜂窝陶瓷催化剂,考察了不同温度焙烧的两类整体催化剂甲苯催化燃烧性能.通过X射线粉末衍射(XRD)、比表面积、拉曼光谱(Raman)、程序升温还原(H2-TPR)、PdO分散度等表征结果与催化活性进行关联.结果表明,随着焙烧温度升高,催化剂比表面积下降,Raman图谱CeO2及PdO峰强度增加,H2-TPR中Ce4+还原峰向高温方向移动,同时PdO分散度下降,相应甲苯催化氧化活性下降.与CeO0.8Zr0.2O2涂层催化剂相比,La3+掺杂催化剂在高温焙烧时,其比表面积下降较小,Raman光谱表明其氧缺位比铈锆涂层催化剂多,H2TPR谱图中Ce4+还原峰低约60～80℃,PdO分散度亦比末掺杂催化剂高.1000℃焙烧下的甲苯氧化反应活性远高于未掺杂催化剂,说明镧的掺杂提高了铈锆涂层催化剂的高温反应活性及热稳定性.     

铝掺杂对铜铈复合氧化物催化一氧化碳氧化性能的影响

以金属硝酸盐为原料、碳酸钠为沉淀剂,采用共沉淀法制备了一系列Cu0.1Ce0.9-xAlxOy复合氧化物催化剂,并用低温氮气吸附/脱附、X-射线衍射(XRD)和氢-程序升温还原(H2-TPR)等对样品进行了表征,利用微反-色谱评价装置考察了催化剂对CO低温氧化反应的活性,研究了Al含量(x=0～0.3)和催化剂焙烧温度(350、500和650℃)对Cu0.1Ce0.9-xAxOy催化活性的影响。结果表明,随着催化剂中Al含量(x)的增加,Cu0.1Ce0.9-xAlxOy的催化活性先提高,至x=0.1时达到最大,之后又逐渐降低;当催化剂的焙烧温度为500℃时,Cu0.1Ce0.8Al0.1Oy的催化活性最大。Cu0.1Ce0.9-xAlxOy的催化活性与其CuO的还原性之间有较好的对应关系。     

镧、铈对Pt, In/Al2O3催化剂选择性还原NO性能的影响

采用溶胶-凝胶法(SG)制备了掺杂少量La或Ce的Pt/Al2O3贵金属催化剂和In2O3/Al2O3氧化物催化剂, 并考察了La或Ce对催化剂的比表面和晶相结构和丙烯在这些催化剂上选择性还原NO的活性. 结果表明, 掺杂少量的La或Ce, 可以改变催化剂的热稳定性, 富氧条件下丙烯选择性催化还原NO的反应中, La或Ce的掺杂对催化活性和催化活性温度窗口没有明显改善.     

高比表面CexTi1-xO2催化剂的结构表征及其HCl催化氧化性能

以硝酸铈,硫酸钛为前驱体,用氨水共沉淀法制备了一系列CexTi1-xO2催化剂.利用XRD、Raman、N2吸附-脱附、H2-TPR对催化剂进行了表征并考察了其催化HCl氧化制Cl2的性能.结果表明:复合氧化物较CeO2和TiO2更加分散甚至高度弥散,大大增加了其比表面积,最高可达170.5 m2·g-1,同时CeO2与TiO2之间的相互作用显著提高了其可还原氧物种数目,改善了其氧化还原性能.催化反应结果表明,复合氧化物的活性较CeO2和TiO2显著提升,Ce0.1Ti0.9O2表现出了良好的氯化氢催化氧化能力和较好的催化稳定性,在430℃时氯气产率可以达到0.90 gCl2·gcat-1·h-1,反应60 h后,氯气产率稳定在0.76 gCl2·gcat-1·h-1.     

镨物种的掺杂量对Co0.1Ce0.9-yPryOx水蒸气重整乙醇反应催化性能的影响

采用XRD,TPR,DSC和TG等方法对共沉淀法制备的Pr物种掺杂Co0.1Ce0.9-yPryOx催化剂的晶相结构、还原性能及反应后催化剂的热性能等进行了表征,并以水蒸气重整乙醇为探针反应考察了催化剂的活性、选择性和稳定性。结果表明:随着镨物种含量的增加,镨离子取代铈离子数量增多,引起晶格畸变,氧空位增多,并有利于钴物种的分散和还原,引导体相氧的溢出和传递。在水蒸气重整乙醇反应中,催化活性、H2的选择性随镨物种含量的增加而提高,而CO和CH4的选择性降低,Co0.1Ce0.70Pr0.2Ox样品在反应50 h后活性和H2的选择性仅下降4.6%和7.9%。     

Zr掺杂对La(Ba)Zr_xCo_(1-x)O_(3-δ)钙钛矿催化N_2O分解性能的影响(英文)

采用溶胶凝胶法制备了Zr掺杂的钴基钙钛矿La(Ba)ZrxCo1-xO3-δ,并将其用于航天推进剂领域的高浓度N2O催化分解反应.发现Zr的引入明显提高了钙钛矿La(Ba)ZrxCo1-xO3-δ的催化活性,尤其是当Zr掺杂量分别为0.05和0.2时,LaZrxCo1-xO3-δ和BaZrxCo1-xO3-δ催化剂性能较为优异.应用N2物理吸附、X射线衍射、H2程序升温还原、O2程序升温脱附和氧脉冲吸附技术表征了Zr掺杂对La(Ba)ZrxCo1-xO3-δ催化剂的物化性质的影响.结果表明,Zr掺杂增大了钴基钙钛矿的比表面积,改善了晶格结构,从而提高了钴物种的还原及氧吸附脱附能力,因而催化剂上N2O分解活性增加.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.