尖晶石LiMn2O4中锂离子嵌入脱出过程的电化学阻抗谱研究

运用电化学阻抗谱(EIS)研究了尖晶石LiMn2O4电极的首次充放电过程. 发现EIS谱高频区域拉长压扁的半圆是由两个半圆相互重叠而成的, 分别归属于与锂离子通过固体电解质相界面膜(SEI膜)的迁移和与尖晶石LiMn2O4材料的电子电导率相关的特征. 通过选取适当的等效电路, 对实验所得的电化学阻抗谱数据进行拟合, 获得尖晶石LiMn2O4电极首次充放电过程中SEI膜电阻、电子电阻和电荷传递电阻等随电极极化电位变化的规律. 根据研究结果提出了嵌锂物理机制模型.     

嵌入化合物电极的电化学阻抗谱: 模型与理论模拟

建立了单个嵌入化合物颗粒、混合颗粒、厚度均匀多孔电极层以及非均匀、多层多孔电极层的理论模型,模拟得了了上述模型的相对应电化学阻抗谱（EIS）特征.结果表明,单个颗粒和混合颗粒表现出相似的阻抗谱特征,均由高频区域内与锂离子通过固体电解质相界面（SEI）膜过程相关的R_SEI‖C_SRI半圆,与电荷传递过程相关的R_ct‖C_dl半圆以及锂离子在固体颗粒内部的扩散相关的斜线三部分组成.对于非均匀、多层多孔嵌入电极而言,一个个新奇的现象就是在阻抗谱中会出现三个半圆,影响第三个半圆现现并形成的因素主要为电极中的颗粒尺寸分布以及电极层的厚度分布,也就是说电极片中出现不同尺寸分布的颗粒以及形成薄厚两种电极层的时候,容易导致阻抗谱中出现第三个半圆.     

锂离子电池的电化学阻抗谱分析

电化学阻抗谱(EIS)是研究电极/电解质界面发生的电化学过程的最有力工具之一,广泛应用于研究锂离子在锂离子电池嵌合物电极活性材料中的嵌入和脱出过程。本文从分析嵌合物电极的EIS谱特征入手,探讨了电化学阻抗谱中各时间常数的归属问题,重点讨论了与锂离子嵌脱过程相关的动力学参数,如电荷传递电阻、活性材料的电子电阻、扩散以及锂离子扩散迁移通过固体电解质相界面膜(SEI膜)的电阻等,对电极极化电位和温度的依赖关系。     

温度对尖晶石LiMn2O4中锂离子嵌脱过程的影响

运用电化学阻抗谱研究了商品化尖晶石LiMn₂O₄电极在1 mol/L LiPF₆-EC(碳酸乙烯酯):DEC(碳酸二乙酯)电解液中―10～30 ℃范围内的阻抗谱特征、固体电解质相界面(SEI)膜阻抗、电子电阻和电荷传递电阻等随温度的变化. 研究结果表明, 尖晶石LiMn₂O₄电极的阻抗谱特征与温度有关, 随温度的升高, 与活性材料电子电导率相关的半圆和与SEI膜相关的半圆会发生重叠而成为一个半圆. 通过选取适当的等效电路拟合了实验所得的电化学阻抗谱数据, 测得尖晶石LiMn₂O₄电极在1 mol/L LiPF₆-EC:DEC 电解液中, 锂离子迁移通过SEI膜的离子跳跃能垒平均值为15.49 kJ/mol; 电子电导率的热激活化能平均值为24.21 kJ/mol; 嵌入反应活化能平均值为53.07 kJ/mol.     

CuF2/MoO3/C复合正极的电化学阻抗谱研究

采用球磨方法制备了CuF2/MoO3/C复合材料电极,利用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、恒流充放电、循环伏安(CV)和电化学阻抗谱(EIS)等方法表征与观察复合材料的结构与形貌,测试了电极的电化学性能.结果表明,球磨CuF2和MoO3晶粒的尺寸为200～300 nm.CuF2/MoO3/C复合电极10 mA.g-1电流密度首次放电容量为647 mAh.g-1,但随之复合材料循环寿命迅速衰减.循环伏安曲线首次放电,2.2 V左右出现了一个还原峰,第2、3周期该还原峰电位升至3.2 V左右.CuF2/MoO3/C复合电极的Nyquist图由高、中频区两个半圆串接和一条斜线组成.放电过程,高频区半圆相应于锂离子扩散多层SEI膜,还与电极材料与集流体的接触有关;中频区半圆与CuF2和MoO3及C的肖特基接触有关;低频区斜线反映扩散传递过程.CuF2/MoO3/C电极电荷传递阻力较大,这可能也是CuF2/MoO3/C电极容量较快衰减的原因.     

嵌钠深度对钠离子电池硬碳负极存储性能的影响

采用扣式半电池研究了嵌钠深度（SOC）对钠离子电池硬碳负极存储性能的影响,并用X射线光电子能谱（XPS）研究了存储过程中固体电解质界面（SEI）的老化机制。结果表明,高SOC状态下存储（>70%）,硬碳活性钠的损失较高,存储6天活性钠损失高达30 mAh/g（占总容量的10%以上）。低SOC状态下有利于减缓存储的老化进程,相应的活性钠损失仅为0.7 mAh/g。这是因为在高SOC状态下,硬碳负极的电位与电解液还原电位之间存在较大的电位差,存储期间持续消耗电解液和活性钠生成大量有机组分,造成SEI厚度明显增加,从而增大界面阻抗;而低SOC存储期时,SEI的厚度增加并不明显,不稳定的有机成分转变成无机成分的重构过程主导了SEI的老化进程。     

钒液流电池用石墨毡电极电化学活化机理的交流阻抗研究

研究了不同氧化程度下的石墨毡在钒溶液中的吸附性、润湿性及其交流阻抗图谱(EIS), 结果发现随着氧化程度增加, 吸附性和润湿性增强; 交流阻抗谱包括两个半圆和一条直线, 高频半圆对应离子的吸脱附反应, 低频半圆对应电化学反应, 直线对应离子在溶液中的扩散过程. 随石墨毡氧化程度的增加, 低频半圆显著减小, 通过等效电路拟合及动力学参数计算, 发现电荷传递电阻显著减小.     

多壁纳米碳管空气电极的交流阻抗研究

研究了多壁纳米碳管、活性炭和石墨等空气电极的交流阻抗特性.结果表明,纳米碳管空气电极的阻抗谱由两个半圆组成,高频区半圆对应欧姆极化阻抗,低频区半圆对应电化学极化阻抗.催化剂Pt以纳米颗粒的形式沉积在碳管的外表面,明显减小了电极的欧姆阻抗和电化学极化阻抗,提高了氧还原反应的电催化活性.活性炭电极除存在电化学阻抗外,还存在薄液膜扩散阻抗(Nernst扩散),石墨电极形成的薄液膜反应区域较小,电极反应呈Warburg扩散阻抗特征,相应的电催化活性较低.采用交流阻抗等效电路分析方法,对拟合的动力学数据进行了解释.     

尖晶石锂锰氧化物电极首次脱锂过程的EIS研究

研究了尖晶石锂锰氧化物电极首次脱锂过程中的电化学阻抗特征. 通过选取适当的等效电路拟合实验所得的电化学阻抗谱数据, 获得了首次脱锂过程中固体电解质相界面膜(SEI膜)的电阻、电容以及电荷传递电阻、双电层电容等随电极极化电位的变化规律.     

温度对LiCoO2中锂离子嵌脱过程的影响

摘要 运用EIS研究了LiCoO2正极在1M LiPF6-EC:DEC:DMC和1M LiPF6-PC:DMC+5%VC电解液中0~30℃范围内阻抗谱特征、SEI膜阻抗、电子电阻和电荷传递电阻等随温度的变化。结果表明,LiCoO2正极的EIS谱特征与温度有关,随温度的升高其低频区域在1M LiPF6-EC:DEC:DMC和1M LiPF6-PC:DMC+5%VC电解液中分别于10和20℃出现反映锂离子固态扩散的斜线。LiCoO2正极在 1M LiPF6-EC:DEC:DMC和1M LiPF6-PC:DMC+5%VC电解液中,锂离子迁移通过SEI膜的离子跳跃能垒平均值分别为37.74和26.55KJ/mol;电子电导率的热激活化能平均值分别为39.08和53.81KJ/mol;嵌入反应活化能平均值分别为68.97和73.73KJ/mol。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.