用常压MIP作原子吸收光谱法原子化器的研究

本文研究了用常压微波诱导等离子体作为原子吸收光谱法的原子化器的可行性, 采用电热蒸发浓硫酸去溶微量进行装置进样, 详细考察了各种实验参数对测定铜的影响。实验证明测定Cu、Ag、Pb的特征浓度分别为0.04、0.04、0.1μg/ml。     

激光原子荧光光谱分析法的进展

概述了激光原子荧光光谱分析法的研究现状和发展趋势。对各种原子化学方法与激光原子荧光光谱分析法相结合的分析特性进行了描述，着重介绍了电热原子化作为原子化器的激光原子荧光光谱法近年来的发展和应用。     

微波诱导等离子体原子吸收光谱法测定Mg,Pb,Zn的研究

微波诱导等离子体(MIP)应用于原子吸收光谱法(AAS)起始于1970年,当时由于灵敏度不高,加之是在减压条件下工作,因而未能引起人们的重视。1988年,本室采用常压Ar—MIP作为AAS的原子化器,用电热进样的方法测定了Cu、Ag、Pb等元素,获得了较好的结果。Ng等人采用气功雾化的进样方法,用MIP—AAS测定了Cu、Mn、Ca等元素,其特征浓度在μg/ml水平。本文是在上述研究的基础上,改用超声雾化方法将样品引入MIP中,用水冷凝和浓H_2SO_4吸收相结合的方法去溶,研究了对Mg、Pb和Zn的测定,并用于实际样品分析,取得了较好的结果。     

恒温炉中加热管材料对灵敏度的影响

恒温炉中加热管石墨表面结构和物理性质,直接影响分析试样的原子化行为。目前,利用热解涂层石墨管改善原子吸收分析灵敏度,已被人们重视并广泛应用^[1-2]。本文采用Woodriff炉做原子化器,对Al、K、Ag、Cd在普通石墨管和玻璃碳管中的原子化行为进行了研究,结果四种元素在玻璃碳管中的灵敏度均获得提高。     

ICP-原子荧光光谱分析

一、前言高频感应耦合等离子体(以下简称ICP)作为优良的蒸发汽化源、原子化源(原子化器)、激发源及离子源而正在发射光谱分析(以下简称AES)中大量应用。然而,由于ICP产生的各种谱线非常多,对于ICP-AES分析,为使分析元素的光谱线分离,必须使用高分辨率的单色器,通常,由于光谱线的重叠或背景等产生的光谱干扰已成为重大的难题。原子荧光光谱分析(以下简称AFS)自1964年由Winefordner     

低温等离子体原子化器-原子荧光光谱法测定碲

基于介质阻挡放电(DBD)原理和结构,建立了适用于原子荧光光谱仪(AFS)的低温等离子体小型原子化器(Atomizer),并研究了氢化物发生-低温等离子体原子化器-原子荧光光谱(HG-DBDAtomizer-AFS)测定环境样品中痕量碲(Te)的分析方法。DBD等离子体原子化器具有小型、低温等优点。对DBD放电结构和放电功率、载气气体流速,氢化物发生过程中的酸度、KBH4浓度,以及观测高度等实验条件进行了详细的考察并优化。本系统测定Te的检出限(3σ)为0.08μg/L;线性范围为0.5～80μg/L;测定精密度为2.1%(n=7);加标回收率为90%～103%。对国家级标准样品(GBW07404,GBW07405,GBW07406)进行测定,测定结果与标准值一致,证明本方法准确可行。     

无火焰原子化-原子吸收光谱法测定不锈钢中砷量

在火焰原子吸收分光光度计火焰上方放置一只特制的不锈钢管作为原子化器,将不锈钢样品溶液定量滴加在不锈钢原子化管内,在乙炔-一氧化二氮高温火焰下对不锈钢样品中微量砷的含量进行无火焰原子化测定,以标准加入法进行定量分析.方法的特征质量为59 pg/1%,绝对检出限(3σ)为3.6 pg.     

基于国产仪器研究钨丝原子吸收光谱

用标准的150 W幻灯灯泡的钨丝作原子化加热材料,设计制作了一种新颖的、结构简单的钨丝电热原子化器,同时还设计了该原子化器的电源电路和信号的数据采集电路.该原子化器能的最高原子化温度可达3100 K左右;编写了硬件的控制软件和信号处理的应用软件.用该原子化器将实验室一台火焰原子吸收光谱仪改装成钨丝原子吸收光谱仪,并以铜元素标准溶液和PerkinElmer公司多元素标准溶液对仪器性能作了研究.仪器对铜的检出限为0.0133 μg/mL,线性范围为0.10～4.0 μg/mL;对1.0 μg/mL的铜标准溶液测试的相对标准偏差为RSD=4.1%(测试次数n=10),每次分析所需样品量20 μL.     

Au-Ag合金纳米粒子制备及其表面增强拉曼光谱研究

首先采用柠檬酸钠法制得Au-Ag合金纳米种子, 然后采用盐酸羟胺生长法得到不同组成的Au-Ag合金纳米粒子. 在其UV-Vis光谱中只观察到一个位于单金属银和金之间的等离子体共振峰, 表明Au-Ag合金纳米粒子已经形成. TEM结果表明, 合金纳米粒子的粒径约为60 nm, 且颜色均一, 没有明显的核壳结构. 用苯硫酚(TP)作为探针分子研究了合金纳米粒子的表面增强拉曼光谱(SERS). 结果表明, SERS强度与合金纳米粒子的组成和尺寸有关. 当纳米粒子粒径一定时, 除Au25Ag75外, 随着金的增加SERS强度增强. Au25Ag75的粒径比Ag小, 导致SERS强度比Ag低. Au50Ag50和Au75Ag25加入TP分子后, 其聚集方式与Au相似, 等离子体共振峰逐渐靠近1064 nm, 金含量较高时, TP的SERS归于聚集体的等离子体共振增强的贡献.     

氢化物发生石墨炉原子吸收进展

在氢化物发生原子吸收光谱中,石英管是使用较为广泛的原子化器,但由于其气相干扰比较严重,石英管表面性质对分析灵敏度影响较大,因而又发展了石墨炉原子化器。自提出涂钯石墨管原位富集氢化物以后,氢化物发生石墨炉原子吸收受到人们的重视。现将氢化物发生石墨炉原于吸收的主要方法分述如下: 1 石墨炉在线原子化法 所谓石墨炉在线原子化法,是将生成的氢化物直接通入已经达到原子化温度的石墨管里的方法。氢化物可以从石墨炉内气路通入石墨管,也可以从石墨管进样孔进入石墨管。由于石墨炉原子化的温度较高,因而能大大减小可以形成氢化物元素的气相干扰。文献[1]比较了石英管和石墨管两种原子化器的抗干扰能力,其中有关砷和硒的干扰情况见表1。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.