气相色谱-串联质谱法测定烟草中97种农药残留量

利用气相色谱-串联质谱法(GC-MS/MS)检测烟草中97种农药残留。样品以乙腈为溶剂经加速溶剂萃取(ASE),提取液用Carbon-NH2固相萃取小柱净化后,采用VF-5MS色谱柱分离,用电子轰击离子源-多反应监测模式(EI-MRM)检测。97种农药的质量浓度在20~1 000μg·L-1范围内与其峰面积呈线性关系,方法的测定下限(10S/N)在0.02~22.4μg·kg-1之间;在50,100,500μg·kg-1的加标水平下,测得回收率在67.4%~116%之间,测定值的相对标准偏差(n=6)在1.9%~14%之间。     

优化的QuEChERS/超高液相色谱-串联质谱法测定鲜茶叶中21种氨基甲酸酯类农药残留

本文应用改进的QuEChERS法结合超高效液相色谱-电喷雾电离串联质谱仪,建立了同时检测鲜茶叶中21种氨基甲酸酯类农药残留的测定方法。样品用1%甲酸乙腈提取,经N-丙基乙二胺(PSA)、C18和石墨化碳黑(GCB)3种复合吸附剂净化,采用UHPLC-MS/MS在动态多重反应监测(DMRM)模式下检测,基质匹配外标法定量。结果表明:21种氨基甲酸酯在2~100μg·L-1范围内线性关系均大于0.995,在三个添加水平下(5、10、25μg·kg-1)的回收率为73.6%~105.0%,相对标准偏差(RSD)为1.4%~7.3%,检出限(LOD)为0.018~0.86μg·kg-1,定量限(LOQ)为0.060~2.87μg·kg-1。该方法样品前处理简单快速、分析时间短、准确度和精密度均符合农药多残留检测技术的要求,适用于鲜茶叶中21种氨基甲酸酯类农药的快速筛查和测定。     

固相萃取-在线凝胶渗透色谱-气相色谱-质谱法测定豆芽中53种农药残留量

采用固相萃取-在线凝胶渗透色谱-气相色谱-质谱法测定豆芽中53种农药残留量。豆芽样品以乙酸-乙腈(1+99)混合液提取,固相萃取小柱净化,采用在线凝胶渗透色谱-气相色谱分离,在质谱分析中采用选择离子监测模式。53种农药的质量浓度均在0.01~1.0mg·L-1范围内与其峰面积呈线性关系,方法的检出限在0.1~6.0μg·kg-1之间。在20,50,100μg·kg-1等3个浓度水平进行加标回收试验,回收率在72.3%~104%之间,测定值的相对标准偏差(n=6)在1.6%~6.6%之间。     

QuEChERS结合HPLC-MC法同时测定黄秋葵中72种农药残留

建立了黄秋葵中72种农药的多残留的液相色谱-串联质谱分析方法。前处理采用改良QuEChERS方法,经乙腈提取,引入缓冲盐体系,使用喷射流离子聚焦-电子喷雾离子源(AJS ESI)和动态多重反应监测(DMRM)模式测定,基质匹配标准曲线定量。结果表明:72种农药在10~200μg·L~(-1)(50~400μg·L~(-1))范围内具有较好的线性关系,相关系数均大于0.997。3个添加水平(10(50)、100、200μg·L~(-1))下,72种农药的加标回收率为78.2%~118.5%。检出限为0.0026~4.9238μg·kg-1,定量限为0.0256~49.2384μg·kg-1,相对标准偏差范围为1.2%~9.8%。该方法样品前处理简单、分析时间短、灵敏、可靠、适用于黄秋葵中多种农药残留的检测。     

低温富集液液萃取-气相色谱-串联质谱法测定水样中15种农药残留

利用低温冷冻条件下农药在水相和有机相之间达到新的传质平衡,建立了低温富集液液萃取-气相色谱-三重四极杆串联质谱法同时测定水样中15种有机磷、有机氯及菊酯类农药的方法。通过对样品前处理中的溶剂选择、冷冻温度及冷冻时间的优化,最终确定的样品前处理条件为:萃取溶剂为甲苯2.0 mL;冷冻温度-40℃;冷冻时间1h。15种农药的检出限(3S/N)在0.005~0.02μg·L-1范围,测定下限(10S/N)为0.02~0.07μg·L-1。方法用于水样中农药的分析,加标回收率在78.8%~124%之间,测定值的相对标准偏差(n=5)在0.9%~9.1%之间。     

UPLC-MS/MS检测3种蔬菜中的11种农药

建立了使用超高效液相色谱-串联质谱(UPLC-MS/MS)快速有效测定甘蓝、豇豆以及菠菜三种蔬菜中11种常见农药残留的方法。蔬菜样品经乙腈提取,Cleanert-NH2固相萃取柱净化后,采用ACQUITY UPLC·BEH C18色谱柱分离,以电喷雾电离、多反应监测模式检测。考察了不同配比的甲醇-水组成的流动相对电离效率、分辨率和灵敏度的影响,研究了不同蔬菜样品中的基质效应。通过基质匹配标准曲线进行定量,11种农药在5~100μg·L-1范围内线性良好,线性相关系数r0.99,目标农药的检出限在0.05~0.5μg·kg-1之间,11种农药在0.01 mg·kg-1,0.05 mg·kg-1和0.10 mg·kg-1三个加标水平下的回收率为80%~120%,相对标准偏差为2.7%~16.3%。     

顶空固相微萃取-气相色谱-质谱法测定蔬菜及水果中15种农药残留量

应用顶空固相微萃取-气相色谱-质谱法测定蔬菜及水果中15种农药的残留量。样品用顶空-固相微萃取进行前处理。经优化的试验条件:1采用100μm聚二甲基硅氧烷萃取头;2离子浓度:样品匀浆液中含(w)30%氯化钠;3萃取温度为70℃±1℃;4萃取时间为30min。在气相色谱分离中用HP-5MS色谱柱,在质谱分析中采用全扫描和选择离子监测模式。15种农药的质量浓度均在0.05~1.0mg·L-1范围内与其峰面积呈线性关系,方法的检出限(3S/N)在0.02~0.10μg·kg-1之间。以2种果品作基体,在0.05,0.2,0.5mg·kg-1 3个浓度水平进行加标回收试验,测得回收率在71.0%~96.0%之间,测定值的相对标准偏差(n=5)在0.5%~9.8%之间。     

毛细管气相色谱法测定沉香中20种有机氯农药残留量

应用毛细管气相色谱法测定沉香中20种有机氯农药的残留量。样品以乙酸乙酯提取,提取液用凝胶色谱-固相萃取(GPC-SEP)进行净化。采用DB-1701P石英毛细管色谱柱(30m×0.25mm,0.25μm)分离样品,电子捕获检测器进行检测。20种有机氯农药的线性范围均为1~50μg·L-1,检出限均为0.1μg·kg-1。方法用于沉香样品分析,加标回收率在95.8%~114%之间,测定值的相对标准偏差(n=6)在0.3%~3.8%之间。     

固相萃取/毛细管气相色谱法测定肉桂皮中六六六、滴滴涕农药残留量

研究了肉桂皮中六六六、滴滴涕农药残留量的测定方法。以丙酮-石油醚混合溶剂为提取剂,旋涡振荡提取,采用固相萃取技术对提取液净化,优化洗脱溶剂的比例和用量,用气相色谱/微电子捕获检测器(μECD)测定。在优化条件下,BHC及DDT农药在10~1 000μg/L质量浓度范围内线性关系良好,相关系数为0.995 8~0.998 1。2种农药在肉桂皮中的加标回收率为92.1%~112%,相对标准偏差(RSD)为2.8%~8.1%,方法的检出限(LODs)为5.0×10-3~2.4×10-2mg·kg-1,定量下限(LOQs)为1.3×10-2~6.0×10-2mg·kg-1。方法具有简单、灵敏、选择性高、重现性好等优点。     

表面活性剂辅助分散液相微萃取-气相色谱法分析蔬菜水果中有机磷类农药残留

建立了测定蔬菜水果中有机磷类农药残留的表面活性剂辅助分散液相微萃取-气相色谱法。优化的萃取条件为:在5.0 mL样品溶液中加入50.0μL三氯甲烷和0.5mL 0.04 mmol·L-1的N-十二烷基-β-氨基丙酸盐表面分散剂,分散混匀后,以5 000r·min-1离心5min,吸取三氯甲烷相直接进样分析。在最优化条件下,8种有机磷类农药在0.02~0.50μg·mL-1范围内具有良好的线性关系,相关系数在0.9948~0.9985之间;检出限为0.0056~0.0110μg·mL-1。有机磷类农药的富集倍数高达264~537倍。方法应用于蔬菜水果中的有机磷类农药分析,加标回收率在82.4%~114.5%之间;相对标准偏差(RSD)在4.9%~13.7%之间。该方法具有操作简单、富集效率高和灵敏度高等特点,可满足蔬菜水果中有机磷类农药残留的检测。     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

A study of the spinel materials LiTi2O4 and Li43Ti53O4 by photoelectron spectroscopy

HeI-excited valence-band ultraviolet photoelectron spectra and MgKα-excited Ti-2p X-ray photoelectron spectra are reported for the spinel materials LiTi₂O₄ and $\text{Li}{}_{\mathrm{<mtext>4</mtext><mtext>3</mtext>}}\text{Ti}{}_{\mathrm{<mtext>5</mtext><mtext>3</mtext>}}\text{O}{}_4$. The presence of a Fermi edge in the ultraviolet photoelectron spectrum of LiTi₂O₄ confirms the metallic nature of this material, although the measured density of states at the Fermi energy is much lower than that expected from an independent-electron interpretation of the magnetic susceptibility. This difference is attributed to a strong interaction of the conduction electrons with the lattice vibrations. The localization of conduction electrons that occurs in the final state in the Ti-2p X-ray photoelectron spectrum of LiTi₂O₄ is attributed to a Coulomb interaction with a core hole.     

Oxygen defect K2NiF4-type oxides: The compounds La2−xSrxCuO4−x2+δ

Oxygen defect K₂NiF₄-type oxides $\text{La}{}_{\mathrm{2?x}}\text{Sr}{}_{\mathrm{x}}\text{CuO}{}_{\mathrm{<mtext>4?</mtext><mtext>x</mtext><mtext>2</mtext><mtext>+\delta </mtext>}}$ have been synthesized for a wide composition range: 0 ≤ x ≤ 1.34. From the X-ray and electron diffraction study three domains have been characterized: orthorhombic compounds with La₂CuO₄ structure for 0 ≤ x < 0.10, tetragonal oxides similar to LaSrCuO₄ for 0.10 ≤ x < 1 and several superstructures derived from the tetragonal cell ( with n = 3, 4, 4.5, 5, 6) for 1 ≤ x ≤ 1.34. The compounds corresponding to 0 < x < 1 differ from the other oxides in that they are characterized by the presence of copper with two oxidation states: + 2 and + 3. A model structure for La_0.8Sr_1.2CuλO_3.4, in which copper has only the + 2 oxidation state, and for which the actual cell is tegragonal—a = 18.80₄ Å and c = 12.94 Å—has been established. The particular structural evolution of these compounds is discussed in terms of a competition between the capability of Cu(II) to be oxidized to Cu(III) and the ordering of oxygen vacancies.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).