金属含量对Ni-Pd/H-Y上正癸烷加氢异构化反应活性和产物选择性的影响

在Y分子筛上浸渍0.1 wt% Pd和0.1–0.5 wt% Ni,用X射线衍射表征了该催化剂的结晶度,用透射电镜测得平均金属粒径.催化剂中Pd和Ni的化学态用X射线光电子能谱测定,其酸性则用氨-程序升温脱附进行了表征,发现一些酸位被Ni2+离子交换.采用程序升温还原表征了HY分子筛负载的Pd, Ni和Pd-Ni催化剂的还原性能.正癸烷加氢异构化反应在200–450 oC和1 atm条件下进行.结果发现,当0.1 wt% Pd/HY中Ni添加量增至0.3 wt%时,正癸烷转化率和异构化选择性增加.单支链和双支链异构体选择性的增加表明该反应遵循质子化环丙烷中间体机理. Ni添加量超过阈值导致活性和异构化选择性急剧下降.综上可见,双金属催化剂更有利于选择性生成双支链异构体,其辛烷值更高.     

金属含量对Ni-Pd/H-Y上正癸烷加氢异构化反应活性和产物选择性的影响（英文）

在Y分子筛上浸渍0.1 wt%Pd和0.1–0.5 wt%Ni,用X射线衍射表征了该催化剂的结晶度,用透射电镜测得平均金属粒径.催化剂中Pd和Ni的化学态用X射线光电子能谱测定,其酸性则用氨-程序升温脱附进行了表征,发现一些酸位被Ni~(2+)离子交换.采用程序升温还原表征了HY分子筛负载的Pd,Ni和Pd-Ni催化剂的还原性能.正癸烷加氢异构化反应在200–450℃和1 atm条件下进行.结果发现,当0.1 wt%Pd/HY中Ni添加量增至0.3 wt%时,正癸烷转化率和异构化选择性增加.单支链和双支链异构体选择性的增加表明该反应遵循质子化环丙烷中间体机理.Ni添加量超过阈值导致活性和异构化选择性急剧下降.综上可见,双金属催化剂更有利于选择性生成双支链异构体,其辛烷值更高.     

Cr改性USY分子筛提高裂化催化剂的异构化性能

在催化裂化过程中，烷烃分子在酸性催化剂表面进行一系列的反应，其中氢转移反应能导致汽油中的烯烃质量分数降低，而异构化、环化、芳构化反应则改善裂化产品的分布，对提高裂化汽油的辛烷值有明显的效果。为了解决我国裂化汽油中烯烃质量分数过高的问题，目前大多数催化裂化装置都采用了降烯烃裂化催化剂，以氢转移反应活性高的REUSY分子筛作为裂化催化剂的活性组分。但由于REUSY分子筛的异构化活性较低，因此裂化汽油的辛烷值有所下降，需要对裂化汽油进行加氢异构化处理。若直接对裂化催化剂进行改性，提高其异构化反应活性，     

Pt/SAPO-11催化剂载体的改性对正十四烷临氢转化性能的影响

以Pt/SAPO-11双功能催化剂为基础,对催化剂载体进行柠檬酸、炭黑改性,以正十四烷为模型化合物,通过催化剂表征和反应评价,探索了催化剂载体的改性对正十四烷临氢转化性能的影响。结果表明,异构化产物以单甲基异构物为主,改性没有改变催化剂的酸强度,但使得酸浓度有所下降。通过柠檬酸调变催化剂的酸性使得催化剂的低温催化活性显著提高,采用炭黑扩孔改性,有效改善了催化剂的传质性能,提高了催化剂的单甲基异构体选择性。柠檬酸和炭黑改性的催化剂裂化产物均以C6为主,改性并没有改变SAPO-11分子筛的孔道限制效应,裂化产物呈现一定的择型效应,裂化产物分布呈现出不对称分布的特点。     

不同链长正构烷烃在Pt/SAPO-11催化剂上的临氢转化规律研究

采用SAPO-11分子筛制备的双功能催化剂,以碳链长度为10-14的正构烷烃为模型化合物,探索了不同碳数的长链正构烷烃临氢转化反应规律。结果表明,低温下不同碳数的正构烃都表现出较高的异构化选择性,改变反应温度使反应转化率控制在85%以下时,正构烷烃的异构化选择性可以达到90%左右;随着碳数和温度升高,正构烷烃由于发生明显的裂化反应导致转化率提高和异构化选择性降低。采用SAPO-11分子筛催化材料的双功能催化剂具有明显的产物择形异构效应,异构化产物以甲基位于端位和碳链中心的单侧链异构体为主,双(多)支链产物较少。长链正构烷烃在Pt/SAPO-11催化剂上的裂化反应在低转化率以加氢裂化为主,裂化产物的碳数呈均匀分布;在高转化率下以酸催化裂化为主,裂化产物的碳数分布呈现明显的不对称分布特征。     

纳米孔Pt-(Re,Sn)/HZSM5-HMS催化剂上正庚烷异构化反应的实验和动力学研究

在200-350℃考察了Pt-(Sn,Re)/HZSM5-HMS催化剂上正庚烷异构化反应.采用X射线衍射、X射线荧光光谱、傅里叶变换红外光谱、紫外-可见光谱、H2程序升温还原、NH3程序升温脱附、吸附吡啶红外光谱、H2化学吸附、N2吸附-脱附、扫描电镜和热重等技术对催化剂进行了表征.在不同的H2和正庚烷分压条件下考察了正庚烷异构化反应动力学,研究了反应条件对催化性能的影响.结果表明,双金属催化剂和三金属催化剂表现出比单金属催化剂更高的催化性能.200℃时Pt-Sn/HZSM5-HMS催化剂表现出最高的异庚烷选择性(＞74％)和多支链异构体选择性(40％).     

纳米孔Pt-(Re,Sn)/HZSM5-HMS催化剂上正庚烷异构化反应的实验和动力学研究（英文）

在200–350°C考察了Pt-(Sn,Re)/HZSM 5-HMS催化剂上正庚烷异构化反应.采用X射线衍射、X射线荧光光谱、傅里叶变换红外光谱、紫外-可见光谱、H2程序升温还原、NH_3程序升温脱附、吸附吡啶红外光谱、H_2化学吸附、N_2吸附-脱附、扫描电镜和热重等技术对催化剂进行了表征.在不同的H_2和正庚烷分压条件下考察了正庚烷异构化反应动力学,研究了反应条件对催化性能的影响.结果表明,双金属催化剂和三金属催化剂表现出比单金属催化剂更高的催化性能.200 oC时Pt-Sn/HZSM 5-HMS催化剂表现出最高的异庚烷选择性(74%)和多支链异构体选择性(40%).     

硅烷化处理对Moo/HZSM-5催化剂上甲烷脱氢芳构化活性的影响

结合催化剂的活性评价及固体高分辨核磁共振谱、X射线光电子能谱和X射线荧光光谱和热重等技术,考察了硅烷化处理对Mo/HZSM-5催化剂上甲烷脱氢芳构化活性的影响.结果表明,采用大分子有机硅烷对HZSM-5分子筛进行硅烷化处理,除去了分子筛外表面的酸性位,并使分子筛本身发生了脱铝.硅烷化处理使Mo/HZSM-5催化剂在进行甲烷脱氢芳构化反应时催化剂上总的积碳量明显减少,从而提高了催化剂的活性.     

硅烷化处理对Mo/HZSM-5催化剂上甲烷脱氢芳构化活性的影响

 结合催化剂的活性评价及固体高分辨核磁共振谱、X射线光电子能谱和X射线荧光光谱和热重等技术,考察了硅烷化处理对Mo/HZSM-5催化剂上甲烷脱氢芳构化活性的影响. 结果表明,采用大分子有机硅烷对HZSM-5分子筛进行硅烷化处理,除去了分子筛外表面的酸性位,并使分子筛本身发生了脱铝. 硅烷化处理使Mo/HZSM-5催化剂在进行甲烷脱氢芳构化反应时催化剂上总的积碳量明显减少,从而提高了催化剂的活性.     

烃类加氢异构化及加氢异构裂化催化剂的研究开发

综述了中国科学院大连化学物理研究所烷烃加氢异构化和加氢异构裂化反应催化剂的研发历程、工业应用及对我国石油炼制工业所做的贡献.1960年代,大连化学物理研究所在烷烃加氢异构化的研究中提出了"电子.酸性催化剂杂交规律",并相继成功研发石蜡基重油加氢异构裂化催化剂和重油单段加氢异构裂化催化剂,并应用于从大庆石蜡基原油馏分生产低冰点航空煤油.重油单段加氢异构裂化催化剂在大庆炼油厂建成的40万吨/年加氢异构裂化装置工业应用已20多年,创造了巨大的经济和社会效益.进入21世纪,大连化学物理研究所又开发出了以分子筛为载体的润滑油基础油加氢异构脱蜡催化剂,于2008年在中国石油大庆炼化公司建成20万吨/年的工业装置实现工业化应用.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。