不同pH条件下木质素磺酸钠的静电逐层自组装研究

以来源于造纸废液中的木质素磺酸钠(SL)为研究对象,利用静电逐层自组装技术,与聚二烯丙基二甲基氯化铵(PDAC)交替吸附,制备木质素磺酸钠的自组装多层吸附膜.研究了不同pH值条件下木质素磺酸钠在固体表面的静电吸附规律.木质素磺酸钠的自组装过程用紫外-可见光吸收光谱来监控,而自组装膜的表面形貌用原子力显微镜来观察.研究表明,SL与PDAC多层吸附膜的紫外-可见光吸收光谱强度随层数增加而线性增长,说明SL/PDAC多层吸附膜的厚度增长是以逐层自组装的方式进行的.木质素磺酸钠浸渍溶液的pH值对多层吸附膜的厚度和表面形貌产生重要的影响.在所研究的pH范围内,pH值越低,越有利于生成吸光度高的自组装膜,而得到的自组装膜的表面粗糙度越大。     

光接枝法制备新型pH开关核孔膜

用表面光接枝方法制备了具有pH开关特性的丙烯酸接枝PET核孔膜 .XPS、SEM和AFM的表征结果证明 ,接枝膜具有非对称结构 ,丙烯酸接枝层主要在膜的向光侧表面 ,膜背侧和膜孔内没有变化 .膜孔周围的接枝链在湿态下沉入膜孔 ,接枝层对膜孔顶部产生封盖 .接枝链的体积随环境pH值的不同而变化 ,从而控制接枝膜的滤过特性 .在低接枝程度时 ,接枝链体积变化对膜孔径的影响小 ,不具有pH开关特性 ,但是接枝提高了膜的亲水性 ,通量得到提高 ;接枝程度达到一定程度时 (如 0 5 %) ,膜孔径受接枝链体积变化的影响显著 ,接枝膜表现出pH开关效应 .在pH大于 5时 ,接枝膜通量恒定 ,基本不受溶液pH值影响 .当pH值小于 4时 ,膜通量随溶液酸性的增加迅速升高 .接枝膜的开关幅度JpH =2 JpH =6 8,随接枝程度的增加而增加 .膜的通量和开关幅度可以通过接枝程度来调节     

温度和溶液pH值交互作用对X80钢在模拟土壤环境中腐蚀行为的影响

利用循环伏安法（CV）、电化学阻抗谱（EIS）和Mott-Schottky曲线研究了温度和溶液pH值交互作用下X80钢在模拟土壤环境中的腐蚀性能。结果表明：低pH值条件下X80钢表面会形成一层稳定性差的腐蚀膜;高pH值条件下X80钢表面会形成一层保护性强的腐蚀膜。随着pH值得增大和温度的降低X80钢表面所成腐蚀膜的膜电阻和传递电阻增大,这表明随着pH值得增大和温度的降低X80钢表面所成腐蚀膜对基体的保护性增强。X80钢在模拟土壤环境中表面所成腐蚀膜呈n型半导体特性,膜内施主密度随介质pH值增大而降低,随溶液温度升高而增大。平带电位和pH值之间呈现线性关系。     

[SiNi(H2O)W11O39]6-多层组装膜修饰电极及其电化学行为

采用电化学生长法制备包含杂多酸[SiNi(H2O)W11O39]6-(SiNiW11)和聚合物阳离子PDDA的多层膜修饰电极, 利用循环伏安法研究其电化学行为、 pH的影响及其对BrO3-和NO2-体系还原的电催化性能;并对多层膜电化学过程机理进行了初步探讨. 结果表明: 多层膜的增长均匀, 峰电流随层数的增加而增加;多层膜的峰电流随扫速的增加而增加;还原峰的峰电位随pH的增加而负移.     

基于聚硫堇和层层组装碳纳米管/HRP的过氧化氢传感器研究

将电聚合和层层组装方法有效结合构筑了聚硫堇（PTH）电子介体修饰的碳纳米管（CNTs）/辣根过氧化物酶（HRP）多层膜无试剂H2O2传感器.利用电化学阻抗谱对CNTs/HRP多层膜的组装过程进行监测,用循环伏安法和计时电流法研究了该HRP电极的电化学行为.探讨了酶组装层数、工作电位、pH值和碳纳米管对电极响应的影响.该...     

牛血清蛋白对二硬脂酰基磷脂酰乙醇胺单层膜结构的影响

利用Langmuir-Blodgett(LB)技术结合原子力显微镜(AFM),研究了牛血清蛋白(BSA)在气/液界面上对二硬脂酰基磷脂酰乙醇胺(DSPE)单层膜结构的影响.通过改变亚相的pH值和BSA浓度,获得了不同条件下DSPE单层膜的等温线、吸附曲线和压缩循环曲线等.实验结果表明,亚相中BSA的存在对DSPE单层膜的压缩性、稳定性以及相变行为产生了较大的影响.吸附动力学结果表明,DSPE单层膜对BSA分子的吸附量存在一定的阈值,且该阈值的大小与亚相pH值相关.通过分析实验数据可知,当亚相pH=3时,BSA的疏水残基几乎全部暴露在外面,2种分子之间的相互作用最强;而pH=7时,BSA仅有少量的疏水残基暴露在外面,2种分子之间的相互作用最弱.原子力显微镜观测到的单层膜形态变化特点与曲线分析结果一致.该研究为了解牛血清蛋白与磷脂分子之间的相互作用机理提供了重要的实验基础和理论依据.     

壳糖胺在铝表面阴极电泳涂膜的形成及机理

研究了CS在铝阴极表面的电泳沉积行为和成膜机理 ,试验了槽压、CS浓度、溶液 pH值、温度、支持电解质品种等对成膜的影响 ,采用XRD、SEM等技术确证涂膜的生成 ,表征了膜层形貌 ,讨论CS电泳沉积的反应历程 .     

钛合金表面铁氧化物膜层类Fenton催化剂制备及降解苯酚性能

采用微弧氧化法在硅酸盐电解液体系中于钛合金表面成功制备了铁氧化物膜层类Fenton催化剂。采用SEM、XRD以及XPS对所得膜层的表面形貌、晶体结构及物相组成进行表征,发现膜层中含有金红石相TiO_2(R-TiO_2),和非晶态的铁氧化物Fe_3O_4;对膜层的表面形貌分析发现电解液中加入铁氰化钾后表面粗糙度及平均孔尺寸增大。以苯酚作为目标降解物,研究了膜层类Fenton催化活性,同时研究了铁源含量、苯酚浓度、H_2O_2投料量以及pH值对膜层降解苯酚效率的影响,优化了降解条件,研究发现在pH 3.0、温度30℃、H_2O_26.0 mmol·L~(-1)、苯酚35 mg·L~(-1)及铁氰化钾含量10 g·L~(-1)的条件下降解90 min,苯酚降解效率可达90%。通过对不同温度下降解苯酚的反应动力学研究,利用阿伦尼乌斯方程得到了该膜层类Fenton降解苯酚的反应活化能Ea为96.9 kJ·mol~(-1)。最后,评价了膜层的稳定性并分析了稳定性衰减的原因。     

一种偶氮聚电解质在不同pH值条件下的静电逐层自组装研究

研究了一种光响应偶氮聚电解质(PEAPE)在不同pH值条件下的自组装,重点讨论了pH值对静电逐层自组装以及对光响应性能的影响.研究表明,在所研究的pH范围内,pH值越低,越有利于生成吸光度高的自组装膜,对应的自组装膜厚度也越大.红外光谱分析表明,偶氮聚电解质在不同pH溶液中存在不同的电离情况.pH值越低,用于自组装的溶液中的聚合物链上的电荷数越少,链构象越卷曲.解释了不同pH值条件下自组装膜吸光度和厚度差别的原因.     

壳聚糖溶液pH对载细胞海藻酸钠-壳聚糖微胶囊性能的影响

以激光共聚焦扫描显微镜为研究手段, 原位直观地考察了在不同pH条件下聚电解质膜的络合程度和蛋白扩散情况. 通过分析pH值对微胶囊膜性能的影响规律, 并结合不同种类细胞对环境pH的敏感特性, 确定了制备细胞培养用海藻酸钠-壳聚糖微胶囊的最佳pH值. 结果表明, 当壳聚糖溶液的pH值由3.50增加到6.50, 微胶囊膜的络合深度呈现高-低-高的趋势, 而微胶囊膜的膨胀性能呈现低-高-低的趋势, 模型蛋白通过微囊膜的扩散呈现低-高-低的趋势, 拐点均出现在pH=4.00和5.50处. 结合动物细胞及微生物细胞对环境pH耐受能力的考察, 确定制备微囊化动物细胞时, 微胶囊成膜反应溶液的最佳pH值为5.50; 制备微囊化大肠杆菌时, 反应溶液的最佳pH值为5.00; 制备微囊化酵母菌时, 反应溶液的最佳pH值为4.50.     

Multilayer film assembled from charged derivatives of chitosan: physical characteristics and biological responses

Polyelectrolyte multilayer films were successfully assembled from each of the three charged derivatives of chitosan; N-[(2-hydroxyl-3-trimethylammonium)propyl]chitosan chloride (HTACC), N-succinyl chitosan (SCC) and N-sulfofurfuryl chitosan (SFC), paired with one of the two oppositely charged polyelectrolytes, poly(acrylic acid) (PAA) and poly(allylamine hydrochloride) (PAH) on surface-treated poly(ethylene terephthalate) (treated PET) substrates by alternate layer-by-layer adsorption. Surface coverage and wettability of the multilayer films were determined by AFM and water contact angle measurements, respectively. Analysis by quartz crystal balance with dissipation (QCM-D) has suggested that all multilayer films are relatively rigid and have a high water content associated within their structures, accounting for up to 85-90% (w/w) for films having 7-10 layers. In vitro cytocompatibility tests for the fibroblast-like L929 cell line revealed a slight dependency for cell adhesion and proliferation on the outermost layer. The multilayer film containing HTACC exhibited moderate antibacterial activity against E. coli and S. aureus. Bearing negative charges, the multilayer films terminating with SFC and having at least 10 layers were capable of suppressing the adsorption of plasma proteins and platelet adhesion at a comparable level to the multilayer film assembled from heparin, a well-known antithrombogenic polymer.     

聚合物层状组装膜

介绍了近几年来我们研究组在层状组装膜的构筑以及功能化研究方面取得的一些最新进展.包括结合表面溶胶-凝胶技术与静电层状组装技术,实现了二阶非线性基团在层状组装多层膜中的非对称排列,制备了具有二阶非线性效应的膜材料;采用室温压印技术,发展了一种简便、经济和具有普适性的层状组装聚合物膜图案化方法;以轻度交联的聚合物微凝胶为构筑基元,制备了具有高负载量的聚合物层状组装膜;发展了一种基于离子剥离技术的层状组装自支持膜制备方法;基于层状组装技术,制备了具有超疏水和抗反射功能的涂层.     

Nanoporosity-driven superhydrophilicity: a means to create multifunctional antifogging coatings

Multifunctional nanoporous thin films have been fabricated from layer-by-layer assembled silica nanoparticles and a polycation. The resultant multilayer films were found to exhibit both antifogging and antireflection properties. The antifogging properties are a direct result of the development of superhydrophilic wetting characteristics (water droplet contact angle <5 degrees within 0.5 s or less). The nearly instantaneous sheetlike wetting promoted by the superhydrophilic multilayer prevents light scattering water droplets from forming on a surface. The low refractive index of the multilayer film (as low as 1.22) resulting from the presence of nanopores was found to impart excellent antireflection properties. Glass slides coated on both sides with a nanoporous multilayer film exhibited transmission levels as high as 99.8%. Stable superhydrophilic wetting characteristics were obtained only after a critical number of bilayers were deposited onto a surface. The assembly conditions (solution pH and nanoparticle concentration), as well as the choice of nanoparticle size, were found to strongly influence film properties. It is suggested that the superhydrophilic behavior is driven by the rapid infiltration of water into a 3D nanoporous network created under specific assembly conditions.     

Assembly of multilayer films from polyelectrolytes containing weak and strong acid moieties

Multilayer films were assembled from a copolymer containing both weakly and strongly charged pendant groups, poly(4-styrenesulfonic acid-co-maleic acid) (PSSMA), deposited in alternation with poly(allylamine hydrochloride) (PAH). The strongly charged groups (styrene sulfonate, SS) are expected to form electrostatic linkages (to enhance film stability), while the weakly charged groups (maleic acid, MA) can alter multilayer film properties because they are responsive to external pH changes. In this study, we varied several assembly conditions such as pH, SS/MA ratio in PSSMA, and the ionic strength of the polyelectrolyte solutions. The multilayer films were also treated by immersion into pH 2 and 11 solutions after assembly. Quartz crystal microgravimetry and UV-visible spectrophotometry showed that the thickness of PSSMA/PAH multilayers decreases with increasing assembly pH regardless of whether salt was present in the polyelectrolyte solutions. When no salt was added, the multilayers are thinner, smoother, and grow less regularly. Atomic force microscopy images indicate that the presence of salt in polyelectrolyte solutions results in rougher surface morphologies, and this effect is especially significant in multilayers assembled at pH 2 and pH 11. When both polyelectrolytes are adsorbed at conditions where they are highly charged, salt was necessary to promote regular multilayer growth. Fourier transform infrared spectroscopy studies show that the carboxylic acids in the multilayers are essentially ionized when assembled from different pHs in 0.5 M sodium chloride solutions, whereas some carboxylic acids remain protonated in the multilayers assembled from solutions with no added salt. This resulted in different pH stability regimes when the multilayers were exposed to different pH solutions, post assembly.     

Fabrication of free-standing multilayer films by using pH-responsive microgels as sacrificial layers

A facile way to prepare free-standing polyelectrolyte multilayer films of poly(sodium 4-styrenesulfonate)(PSS)/poly(diallyldimethylammonium)(PDDA) was developed by applying a new pH-dependent sacrificial system based on cross-linked poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA) microgels. The tertiary amine groups of PDMAEMA microgels can be protonated in acidic environment, and the protonated microgels were deposited by layer-by-layer (LbL) technique with PSS. PSS/PDDA multilayer films were constructed on the top of the PSS/microgels sacrificial layers. The LbL assembly process was investigated by UV–vis spectroscopy. Further study shows that the free-standing PSS/PDDA multilayer films can be obtained within 3 min by treating the as-prepared films in alkali aqueous solution with a pH of 12.0. The pH-triggered exfoliation of PSS/PDDA multilayer films provides a simple and facile way to prepare LbL assembled free-standing multilayer films.     

Electric-field-induced fabrication of covalently linked second-order nonlinear optical multilayer films on nonconductive substrates

A highly stable second-order nonlinear optical multilayer film was constructed on insulating substrates using the electric-field-induced layer-by-layer assembly technique. The substrates used in this method could be arbitrary. In another, the substrates could be modified with polyanion solution by spin coating as cladding layer. Then, the nonlinear optical multilayer films were assembled on the cladding layer directly by the electric-field-induced layer-by-layer assembly technique. The resulting cross-linked multilayer films fabricated by this method displayed high optical transparency, good thermal stability, and excellent nonlinear optical properties which can be made into waveguide devices directly.     

pH-controlled construction of chitosan/alginate multilayer film: characterization and application for antibody immobilization

In this work, a chitosan/alginate multilayer film was constructed via layer-by-layer self-assembly and studied by in situ surface plasmon resonance monitoring and contact angle measurements. The results demonstrate that the surface composition of the self-assembled multilayer film can be simply tailored through pH control during the assembly process. The biological property of the assembled film was further characterized via antigen-antibody interactions, showing that the loading capacity of the antibody on the multilayered film and the binding activity of the antigen to the immobilized antibody could be also well-tuned by pH control. This work can provide more scientific insight in the interaction between protein and polymer matrix and render a novel simple approach to build high-performance biointerfaces through pH control for potential applications of highly sensitive immunosensors.     

Mussel-inspired chemistry for robust and surface-modifiable multilayer films

In this article, we report a bioinspired approach to preparing stable, functional multilayer films by the integration of mussel-inspired catechol oxidative chemistry into a layer-by-layer (LbL) assembly. A polyanion of poly(acrylic acid-g-dopamine) (PAA-dopamine) bearing catechol groups, a mussel adhesive protein-mimetic polymer, was synthesized as the building block for LbL assembly with poly(allylamine hydrochloride) (PAH). The oxidization of the incorporated catechol group under mild oxidative condition yields o-quinone, which exhibits high reactivity with amine and catechol, thus endowing the chemical covalence and retaining the assembled morphology of multilayer films. The cross-linked films showed excellent stability even in extremely acidic, basic, and highly concentrated aqueous salt solutions. The efficient chemical cross-linking allows for the production of intact free-standing films without using a sacrificial layer. Moreover, thiol-modified multilayer films with good stability were exploited by a combination of thiols-catechol addition and then oxidative cross-linking. The outstanding stability under harsh conditions and the facile functionalization of the PAA-dopamine/PAH multilayer films make them attractive for barriers, separation, and biomedical devices.     

Durable antifog films from layer-by-layer molecularly blended hydrophilic polysaccharides

Mechanically durable, long-lasting antifog coatings based on polysaccharides were developed using a layer-by-layer (LBL) assembly process. The unique properties of these coatings are a result of a molecular-level blending of the polysaccharides, with multilayers containing chitosan and carboxymethyl cellulose providing the best overall properties. The antifog properties resulted from a strong interaction between the polar and H-bonding elements of the assembled polymers and water molecules and the concomitant formation of thin films of water. Environmental scanning electron microscopy (ESEM) studies confirmed that fogging coatings are decorated with light scattering, micrometer-sized droplets of water whereas antifogging coatings remain droplet free. To improve the mechanical durability of the multilayer films on substrates, the surface was modified via self-assembly of epoxy-functionalized silane molecules. Cross-linking chemistry was then applied to improve the mechanical robustness of the LBL films on various surfaces. These films were characterized using several techniques: optical profilometery (PL), spectroscopic ellipsometry (EL), contact angle goniometry (CA), and atomic force microscopy (AFM). The antifog properties of the films were evaluated by several tests under different environmental conditions. This work demonstrates that the unique water-adsorbing properties of polysaccharides can be exploited to create permanent antifog properties, which may be useful for various applications.     

Molecular dynamics simulations of multilayer films of polyelectrolytes and nanoparticles

We performed molecular dynamics simulations of multilayer assemblies of flexible polyelectrolytes and nanoparticles. The film was constructed by sequential adsorption of oppositely charged polymers and nanoparticles in layer-by-layer fashion from dilute solutions. We have studied multilayer films assembled from oppositely charged polyelectrolytes, oppositely charged nanoparticles, and mixed films containing both nanoparticles and polyelectrolytes. For all studied systems, the multilayer assembly proceeds through surface overcharging after completion of each deposition step. There is almost linear growth in the surface coverage and film thickness. The multilayer films assembled from nanoparticles show better layer stratification but at the same time have higher film roughness than those assembled from flexible polyelectrolytes.