pH响应性P(MMA-co-MAA-co-HEMA)微凝胶的制备及其性能

利用预乳化乳液法制备了不同单体配比的聚(甲基丙烯酸甲酯-co-甲基丙烯酸-co-甲基丙烯酸羟乙酯)(P(MMA-co-MAA-co-HEMA))微凝胶分散液;采用透射电子显微镜、动态光散射仪研究了微凝胶的微观形态、粒径大小及其溶胀率;利用试管倒转法对微凝胶分散液的凝胶化相转变行为进行了研究,借助椎板流变仪考察了所形成胶态凝胶的储能模量与单体配比、微凝胶分散液浓度和温度的关系.结果表明,所制备的微凝胶的数均粒径为90 nm左右,当MMA与MAA的投料质量不变时,随着HEMA含量的增加,分散液凝胶化所需的临界最小浓度增大,临界最大pH值减小,胶态凝胶的储能模量增加.当保持单体MMA与HEMA的投料质量不变时,随着单体MAA投料质量的增多,微凝胶的数均粒径和溶胀率增大,胶态凝胶的储能模量先升高后降低;当MAA占单体总摩尔数的25%时,浓度为15 wt%的微凝胶分散液在扫描频率为100 rad/s时,胶态凝胶的储能模量最高可达2×104Pa.这类微凝胶分散液在组织工程支架材料方面有潜在的应用价值.     

P(AMPS-co-HEMA)凝胶的合成与吸银性能研究

以2-丙烯酰胺基-2-甲基丙磺酸(AMPS)和甲基丙烯酸羟乙酯(HEMA)为单体,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,过硫酸钾(KPS)为引发剂,采用自由基水溶液聚合法制备P(AMPS-co-HEMA)共聚凝胶,通过傅里叶红外光谱(FT-IR)对材料结构进行了表征.研究单体配比、交联剂的用量、引发剂的用量对共聚凝胶吸水性能的影响,并在此基础上对凝胶的溶胀、吸银及消溶胀性能进行研究.结果表明,当单体摩尔比n(AMPS)∶n(HEMA)=2∶1,交联剂用量ω(MBA)=0.6％,引发剂用量ω(KPS)=0.8％,所制得的凝胶吸水性能最好;凝胶在蒸馏水中的溶胀过程属于松弛平衡扩散;凝胶在AgNO3溶液中60min左右达到消溶胀平衡,且当AgNO3溶液的浓度为0.05mol/L时,银离子吸附量最大,为0.04g/g,消溶胀速率最快.     

基于超支化聚合物两性水凝胶的制备及性能

通过N-丙烯酰-1,2-乙二胺盐酸盐(ADE)的Michael加成反应制备阳离子超支化低聚物聚N-丙烯酰-1,2-乙二胺盐酸盐(HADE),以HADE为大分子单体,以丙烯酰胺(AAm)和丙烯酸(AAc)为单体,在无需外加有机交联剂的条件下制备具有高机械强度的两性聚电解质水凝胶(HAH凝胶).结果表明,HAH凝胶可以被压缩超过99%的形变而不断裂,压缩强度高达61.2 MPa;HAH凝胶的断裂伸长率和断裂强度分别达到1700%和70.2 k Pa.由于HADE末端伯胺基与强氧化引发剂通过氧化还原反应生成胺自由基和自身结构中的双键同时参与聚合反应,因而为凝胶网络形成提供了必要的化学交联作用.同时HADE结构中胺基正电荷与AAc的羧基负电荷之间的离子交联也为凝胶网络提供了物理交联作用.2种交联作用的协同作用是HAH凝胶具有良好机械性能的根本原因.     

离子键交联的聚两性电解质凝胶在不同pH和不同电解质溶液中溶胀行为研究

以丙烯酸(AA)和甲基丙烯酸二乙氨基乙酯(DEAM)形成的离子复合物与丙烯酰胺(AAm)共聚,合成了一种新型的离子键交联的聚两性电解质凝胶(PADA).由于分子之间的氢键作用,PADA凝胶并不是在A/C(负正离子单体摩尔比)为1,而是在A/C为1.55处有最大消溶胀.与共价键交联的聚两性电解质凝胶相比,PADA凝胶的溶胀行为具有更强的pH敏感性.PADA凝胶在不同pH缓冲溶液中的溶胀行为表明,在pH 3~4之间消溶胀程度最大.在偏离该pH区域时凝胶均发生溶胀.但凝胶的溶胀程度在pH<3的酸性溶液中随A/C的增加而降低;而在pH>4的偏碱性溶液中随其增加而增加.在不同价数的离子溶液中,离子浓度对于PADA凝胶的平衡溶胀有着不同的影响.对于一价的NaCl溶液,PADA凝胶有典型的反聚电解质效应.但对于高价的CaCl2和柠檬酸三钠溶液,只在较低的浓度下,才表现出反聚电解质效应.而在较高盐浓度时,随盐浓度的增加其溶胀比反而降低.这可能与高价离子形成的离子键交联有关.与pH对PADA凝胶溶胀程度的影响相似,在CaCl2溶液中,PADA凝胶的溶胀程度随A/C的增加而降低;而在柠檬酸三钠溶液中则刚好相反.这种独特的溶胀行为似乎与高价离子电荷的正负性有关.     

羧甲基纤维素与丙烯酸接枝共聚凝胶的溶胀动力学及过溶胀平衡特性的研究

采用接枝共聚合成了羧甲基纤维素钠、丙烯酸与N,N′-亚甲基双丙烯酰胺的交联凝胶, 研究了这类凝胶在不同pH值的缓冲溶液中的溶胀行为, 发现在酸性介质中凝胶的溶胀动力学行为表现出过溶胀平衡特性(overshooting effect), 即凝胶先发生溶胀到最大值, 然后再逐渐消溶胀到平衡. 这种现象可归因于凝胶溶胀过程中羧基之间通过氢键所产生的协同物理交联. 较之凝胶的组成, 缓冲溶液的pH值对过溶胀平衡现象的影响更为显著. 前者是因为凝胶羧基的总摩尔分数并不随两组分结构单元摩尔数的改变而改变, 羧基之间通过氢键形成的物理交联程度在交联剂摩尔分数接近的条件下变化不大; 后者是由于溶液的pH值显著影响凝胶羧基的质子化程度, 进而影响羧基之间通过氢键形成的物理交联程度. 凝胶在酸性介质中的溶胀过程符合E. Díez-Peña等提出的溶胀动力学定量模型, 理论曲线与实验数据有较好的相关性. 凝胶在pH≥5.0的缓冲溶液中的溶胀不产生过溶胀平衡现象, 这一现象归因于完全离子化的羧基之间不能形成物理交联. 凝胶的溶胀过程遵循Schott二级溶胀动力学.     

基于壳聚糖/聚丙烯酸/纳米银的高强抗菌水凝胶

首先以丙烯酸(AA)和壳聚糖(CS)为单体、N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,通过光聚合法制备了CS/PAA双网络水凝胶,然后将Ag~+以硝酸银的形式分散在水凝胶中并通过紫外光辐照获得CS/PAA/纳米银复合水凝胶,并对复合水凝胶的抗菌性能进行研究。采用红外光谱对其结构进行表征,研究单体含量对水凝胶力学性能以及溶胀行为的影响。结果表明,当丙烯酸质量分数为20%,壳聚糖质量分数为5%的情况下,水凝胶的拉伸性能最优。此外,纳米银的引入有效提高了水凝胶的抗菌性能。     

pH响应型P(HEMA/MAA)纳米微凝胶分散液的凝胶化行为和流变性能

制备了在修复受损组织方面有应用潜能的纳米级聚(甲基丙烯酸羟乙酯/甲基丙烯酸) (P(HEMA/MAA))微凝胶; 采用试管倒转法对不同pH值和浓度的P(HEMA/MAA)微凝胶分散液的凝胶化相转变行为进行了研究; 借助椎板流变仪考察了低浓度和高浓度微凝胶分散液的流变性能, 并对pH触发物理凝胶化相转变机理进行了推测. 结果表明: 在生理pH值环境下, 一定浓度的P(HEMA/MAA)微凝胶分散液可以发生凝胶化相转变形成凝胶态, pH=7时, HEMA/MAA进料摩尔比为8/2的微凝胶分散液凝胶化后得到的凝胶力学性能最佳, 最大弹性模量(G')可达7.58×10³ Pa; P(HEMA/MAA)微凝胶颗粒在不同条件下具有不同的溶胀效果, 导致低浓度分散液的表观粘度发生相应的变化, 并由此推测出微凝胶颗粒的溶胀过程由外及内, 分为三个阶段; 高浓度微凝胶分散液发生凝胶化相转变主要是由颗粒间或颗粒与分散介质间形成的空间静电稳定作用和氢键共同作用引起的.     

N-异丙基甲基丙烯酰胺共聚热缩温敏水凝胶

从甲基丙烯腈与异丙醇反应制备了N-异丙基甲基丙烯酰胺(NIPM),研究了其以N,N′-亚甲基双丙烯酰胺(MBA)为交联剂在不同溶剂体系的聚合及所形成的水凝胶的性质。表明NIPM-MBA凝胶具有热缩温敏性。在NIPM-MBA体系引入丙烯酸钠、甲基丙烯酸钠等负离子单体时,凝胶的溶胀比明显增加,MBA所占比例较少的体系,具有热缩、热胀双重性。     

微波辅助合成聚酰胺-胺修饰硅胶及其对牛血清白蛋白的吸附性能研究

采用微波辅助合成法制备了聚酰胺-胺树枝状大分子修饰硅胶,并考察了其对牛血清白蛋白(BSA)的吸附性能。PAMAM修饰硅胶的合成条件通过元素分析进行考察,不同代数PAMAM修饰硅胶通过傅里叶变换红外光谱法表征。结果表明,在微波辅助下制备的PAMAM修饰硅胶的红外光谱图中出现酰胺的特征吸收峰与采用传统加热方法的文献报道一致,而采用微波辅助和传统加热方法的反应时间分别为40min和24h,由此说明微波辅助合成聚酰胺-胺树枝状大分子修饰硅胶是可行的。同时研究还发现聚酰胺-胺修饰硅胶对蛋白的吸附能力比未经修饰的硅胶强,而且蛋白的吸附量随着聚酰胺-胺代数的增加而增加。     

PMAA纳米水凝胶的水相制备

利用表面活性剂间的疏水作用以及表面活性剂与单体间的氢键作用,促使甲基丙烯酸(MAA)单体在原位生成的聚甲基丙烯酸甲酯(PMMA)种子乳胶表面的选择性聚合,实现了PMAA纳米水凝胶的水相"绿色"制备。利用动态光散射、傅里叶红外光谱、透射电子显微镜表征了PMAA纳米水凝胶的尺寸、组成、形貌和pH响应性。研究了聚氧乙烯失水山梨醇单月桂酸酯(吐温20)的用量、N,N’-亚甲基双丙烯酰胺(MBA)的用量、MAA的用量和加入方式、十二烷基硫酸钠(SDS)的补加速率等对PMAA纳米水凝胶的尺寸和溶胀性能的影响。结果表明:PMAA纳米水凝胶为核-壳结构;随着MBA用量的减小、吐温20用量的增加、MAA用量的增加,PMAA纳米水凝胶的尺寸和溶胀比均增大;当采用半连续加入MAA时,PMAA纳米水凝胶的尺寸和溶胀比变小;当SDS的补加时间由60min延长到100min时,PMAA纳米水凝胶的尺寸逐渐变小。PMAA纳米水凝胶具有良好的pH响应性,当介质的pH从1增加到6时,其流体力学体积扩张了64倍。     

Study on hypochlorite degradation of aromatic polyamide reverse osmosis membrane

A serious limitation of most commercial polyamide reverse osmosis (RO) membranes is their sensitivity to chlorine attack. By studying the hypochlorite degradation of aromatic polyamide RO membrane, this work was to get some understandings in the prevention of membrane depreciation and develop membranes with improved chlorine resistance. Membrane performances, including water flux and salt rejection, were evaluated before and after hypochlorite exposure under different pH and concentration conditions. The results showed that chlorination destroyed hydrogen bonds in polyamide chains, causing a notable decline of membrane flux especially in acid environment; however, membrane performance was slightly improved after the treatment of alkaline hypochlorite solution for a certain time, which was probably due to the effect of amine groups in barrier layer. Based on the attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) characterizations and performance measurements, the results indicated that N-chlorination reaction of aromatic polyamide was also reversible, in other words, the N-chlorinated intermediate could be regenerated to initial amide with the alkaline treatment before ring-chlorination reaction. This conclusion provided several relative suggestions for membrane cleaning procedures. Finally, a method adopting surface coating was proposed to develop membranes with good chlorine resistance, and the preliminary results showed its potential for applications.     

Preparation and characterization of novel physically cross-linked hydrogels composed of poly(vinyl alcohol) and amine-terminated polyamidoamine dendrimer

Poly(vinyl alcohol) (PVA) and polyamidoamine (PAMAM) dendrimers are water-soluble, biocompatible and biodegradable polymers, which have been widely applied in biomedical fields. In this paper, novel physically cross-linked hydrogels composed of PVA and amine-terminated PAMAM dendrimer G6-NH(2) were prepared by cyclic freezing/thawing treatment of aqueous solutions containing PVA and G6-NH(2). The FT-IR analysis and elemental analysis indicated that PAMAM dendrimer G6-NH(2) was successfully introduced into the formed hydrogels, possibly via hydrogen bonds among hydroxyl groups, amide groups and amino groups in PVA and PAMAM dendrimer in the process of freezing-thawing cycle. Compared with physically cross-linked PVA hydrogel, PVA/G6-NH(2) hydrogels show higher swelling ratios and faster re-swelling rate due to the higher hydrophilicity of PAMAM dendrimer G6-NH(2). Higher contents of G6-NH(2) in PVA/G6-NH(2) hydrogels resulted in higher swelling ratios and faster re-swelling rates. With increasing freezing/thawing cyclic times, the swelling ratios and re-swelling rates of PVA/G6-NH(2) hydrogels decreased, which is similar to that of physically cross-linked PVA hydrogel. Combining the special host property of polyamidoamine dendrimer, these novel physically cross-linked hydrogels are expected to have potential use in drug delivery, including improving drug-loading amounts in hydrogels and prolonging drug release time. Swelling ratios of physically cross-linked PVA/G6-NH(2)-50 hydrogels prepared by three, six, nine freezing/thawing cycles. The swelling equilibrium experiments were carried out in distilled water at 25 degrees C.     

Swelling-shrinking behavior of chemically cross-linked polypeptide gels from poly(α-L-lysine), poly(α-DL-lysine), poly(ɛ-L-lysine) and thermally prepared poly(lysine): effects of pH, temperature and additives in the solution

We synthesized the glutaraldehyde cross-linked hydrogels using four kinds of poly(lysine)s (PLs) and measured the equilibrium swelling ratio (Q) as a function of pH. Also measured was the temperature change of Q at a fixed pH (11.6) in the absence and presence of additives (LiBr, methanol and urea) that affect the secondary structure of PLs. The swelling data were examined using a force balance approach in which the repulsive and attractive interactions among the cross-linked PL chains were considered based on the conformational properties of PLs in aqueous solutions. It was found that the formation of the helical segments in the cross-linked chain has little effect in the gel collapse, but their association acts as the attractive interaction causing the gel to shrink. The formation of the beta-sheet structure within the network also acts as the attractive interaction. These attractive interactions are mainly due to the hydrogen bonding, but hydrophobic interactions between the lysine side chains should be considered. In addition, in the swelling behavior of all the PL gels the polyampholyte nature appears due to electrostatic interactions of the basic groups with the C-terminal carboxyl group.     

利用聚乙烯醇结晶辅助制备多重交联的高强度聚丙烯酰胺水凝胶

在表面带有C=C双键的乙烯基杂化二氧化硅纳米颗粒(vinyl hybrid silica nanoparticle,VSNP)上接枝丙烯酰胺(AM),所得到的纳米刷状凝胶因子通过聚丙烯酰胺(PAM)间的氢键形成物理交联点,则多官能化的VSNP可作为拟共价交联点构筑双重交联的单一网络纳米复合物理水凝胶(nanocomposite physical hydrogel,NCP gel),表现出较高的强度和超拉伸性.为了进一步提高凝胶的强度和韧性,将少量PVA和PAM/VSNP纳米刷混合制成凝胶,通过冷冻-融化处理,使与PAM分子链相互缠绕并形成氢键作用的PVA结晶,形成新的交联点进一步交联PAM NCP gel,得到多交联的PAM NCP gel体系.通过拉曼光谱和示差扫描量热分析,证明凝胶中的PVA通过氢键既可以与PAM相互作用,又形成微晶为新交联点,大大增强了NCP gel的力学性能,与PAM NCP gel相比,凝胶的拉伸强度和断裂能分别从313 k Pa和1.41×104 J/m~2提高到了557k Pa和4.65×104 J/m~2.     

One-pot synthesis of hyperbranched poly(amido amine) clicked with a sugar shell via Michael addition polymerization and thiol click reaction

This paper reports the production of glycopolymers via a simple and flexible method. A novel glycopolymer with a hyperbranched poly(amido amine) core and a sugar shell (HPAA-GLc) was synthesized by using thiol-ene click reaction via facile one-pot method. Hyperbranched poly(amido amine) with vinyl terminals was first synthesized by Michael addition polymerization of N,N′-methylene bisacrylamide (MBA) with 1-(2-aminoethyl) piperazine (AEPZ). Subsequently, thiol-ene click reaction between vinyl units of hyperbranched poly(amido amine) and thio-glucose was performed in situ. Based on the NMR result, all the vinyl groups reacted with thiol-glucose in 120 min. Strong photoluminescence emission was observed from the aqueous solution of HPAA-GLc.     

Anisotropically Swelling Gels Attained through Axis‐Dependent Crosslinking of MOF Crystals

Anisotropically deforming objects have attracted considerable interest for use in molecular machines and artificial muscles. Herein, we focus on a new approach based on the crystal crosslinking of organic ligands in a pillared‐layer metal–organic framework (PLMOF). The approach involves the transformation from crosslinked PLMOF to polymer gels through hydrolysis of the coordination bonds between the organic ligands and metal ions, giving a network polymer that exhibits anisotropic swelling. The anisotropic monomer arrangement in the PLMOF underwent axis‐dependent crosslinking to yield anisotropically swelling gels. Therefore, the crystal crosslinking of MOFs should be a useful method for creating actuators with designable deformation properties.     

Enhancing amine terminals in an amine-deprived collagen matrix

Collagen, though widely used as a core biomaterial in many clinical applications, is often limited by its rapid degradability which prevents full exploitation of its potential in vivo. Polyamidoamine (PAMAM) dendrimer, a highly branched macromolecule, possesses versatile multiterminal amine surface groups that enable them to be tethered to collagen molecules and enhance their potential. In this study, we hypothesized that incorporation of PAMAM dendrimer in a collagen matrix through cross-linking will result in a durable, cross-linked collagen biomaterial with free -NH 2 groups available for further multi-biomolecular tethering. The aim of this study was to assess the physicochemical properties of a G1 PAMAM cross-linked collagen matrix and its cellular sustainability in vitro. Different amounts of G1 PAMAM dendrimer (5 or 10 mg) were integrated into bovine-derived collagen matrices through a cross-linking process, mediated by 5 or 25 mM 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC) in 5 mM N-hydroxysuccinimide (NHS) and 50 mM 2-morpholinoethane sulfonic acid buffer at pH 5.5. The physicochemical properties of resultant matrices were investigated with scanning electron microscopy (SEM), collagenase degradation assay, differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectra, and ninhydrin assay. Cellular sustainability of the matrices was assessed with Alamar Blue assay and SEM. There was no significant difference in cellular behavior between the treated and nontreated groups. However, the benefit of incorporating PAMAM in the cross-linking reaction was limited when higher concentrations of either agent were used. These results confirm the hypothesis that PAMAM dendrimer can be incorporated in the collagen cross-linking process in order to modulate the properties of the resulting cross-linked collagen biomaterial with free -NH 2 groups available for multi-biomolecular tethering.     

Swelling behavior of chemically crosslinked PVA gels in mixed solvents

We report the swelling behavior of chemically crosslinked polyvinyl alcohol (PVA) gels with different degrees of hydrolysis in water, several organic solvents, and their mixed solvents. The gels were dried after gelation and were put into their respective solvents. The gel volume in pure water decreased with increasing temperatures, and the total changes increased with decreasing degrees of hydrolysis. The swelling ratio depends on the solvent and its concentration. In the cases of mixed solvents of methanol–water, ethanol–water, and acetone–water, the gels shrank continuously with increasing concentrations of solvents and reached the collapsed state in the pure organic solvent. In the case of dimethyl sulfoxide (DMSO), on the other hand, the gels shrunk, swelled, and finally reached the swollen state in pure DMSO. Results of measurements using Fourier Transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD) suggested that crosslinks and microcrystallites were formed due to hydrogen bonds during the drying process after gelation. The hydrogen bonds were partly destroyed in a rich solvent, but the residual hydrogen bonds had an essential role in determining the swelling behavior in a poor solvent. The swelling behavior and the possible phase transition of the present system are discussed in terms of the solubility of polymers with different degrees of hydrolysis in given mixed solvents and in terms of the formation and destruction of physical crosslinks in the chemical PVA gels. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1978–1986, 2010     

4-Mercaptophenylboronic acid SAMs on gold: comparison with SAMs derived from thiophenol, 4-mercaptophenol, and 4-mercaptobenzoic acid

We report the formation and characterization of self-assembled monolayers (SAMs) derived from the adsorption of 4-mercaptophenylboronic acid (MPBA) on gold. For comparison, SAMs derived from the adsorption of thiophenol (TP), 4-mercaptophenol (MP), and 4-mercaptobenzoic acid (MBA) were also examined. The structure and properties of the SAMs were evaluated by ellipsometry, contact-angle goniometry, polarization-modulation infrared reflection-absorption spectroscopy (PM-IRRAS), and X-ray photoelectron spectroscopy (XPS). Specifically, ellipsometry was used to assess the formation of monolayer films, and contact angle measurements were used to determine the surface hydrophilicity and homogeneity. Separately, PM-IRRAS was used to evaluate the molecular composition and orientation as well as the intermolecular hydrogen bonding within the SAMs. Finally, XPS was used to evaluate the film composition and surface coverage (i.e., packing density), which was observed to increase in the following order: TP < MP < MPBA < MBA. A rationalization for the observed packing differences is presented. The XPS data indicate further that ultrahigh vacuum conditions induce the partial dehydration of MPBA SAMs with the concomitant formation of surface boronic anhydride species. Overall, the analytical data collectively show that the MPBA moieties in the SAMs exist in the acid form rather than the anhydride form under ambient laboratory conditions. Furthermore, stability studies find that MPBA SAMs are surprisingly labile in basic solution, where the terminal B-C bonds are cleaved by the attack of hydroxide ion and strongly basic amine nucleophiles. The unanticipated lability observed here should be considered by those wishing to use MPBA moieties in carbohydrate-sensing applications.     

Mechanism and kinetics of the crosslinking reaction between biopolymers containing primary amine groups and genipin

The reaction mechanism of chitosan, bovine serum albumin (BSA), and gelatin with genipin (a natural crosslinking reagent) was examined with infrared, ultraviolet–visible, and ¹³C NMR spectroscopies; protein‐transfer reaction mass spectrometry; photon correlation spectroscopy; and dynamic oscillatory rheometry. Two reactions that proceeded at different rates led to the formation of crosslinks between primary amine groups. The fastest reaction to occur was a nucleophilic attack on genipin by a primary amine group that led to the formation of a heterocyclic compound of genipin linked to the glucosamine residue in chitosan and the basic residues in BSA and gelatin. The second, slower, reaction was the nucleophilic substitution of the ester group possessed by genipin to form a secondary amide link with chitosan, BSA, or gelatin. A decreased crosslinking rate in the presence of deuterium oxide rather than water suggested that acid catalysis was necessary for one or both of the reactions to proceed. The behavior of the gel time with polymer concentration was consistent with second‐order gelation kinetics resulting from an irreversible crosslinking process, but was complicated by the oxygen radical‐induced polymerization of genipin that caused the gels to assume a blue color in the presence of air. The lower elastic modulus attained after a given time during crosslinking of the globular protein BSA as compared to the coiled protein gelatin, despite possessing more crosslinkable basic residues, demonstrated the importance of protein secondary and tertiary structures in determining the availability of sites for crosslinking with genipin in protein systems. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3941–3953, 2003