pH响应性P(MMA-co-MAA-co-HEMA)微凝胶的制备及其性能

利用预乳化乳液法制备了不同单体配比的聚(甲基丙烯酸甲酯-co-甲基丙烯酸-co-甲基丙烯酸羟乙酯)(P(MMA-co-MAA-co-HEMA))微凝胶分散液;采用透射电子显微镜、动态光散射仪研究了微凝胶的微观形态、粒径大小及其溶胀率;利用试管倒转法对微凝胶分散液的凝胶化相转变行为进行了研究,借助椎板流变仪考察了所形成胶态凝胶的储能模量与单体配比、微凝胶分散液浓度和温度的关系.结果表明,所制备的微凝胶的数均粒径为90 nm左右,当MMA与MAA的投料质量不变时,随着HEMA含量的增加,分散液凝胶化所需的临界最小浓度增大,临界最大pH值减小,胶态凝胶的储能模量增加.当保持单体MMA与HEMA的投料质量不变时,随着单体MAA投料质量的增多,微凝胶的数均粒径和溶胀率增大,胶态凝胶的储能模量先升高后降低;当MAA占单体总摩尔数的25%时,浓度为15 wt%的微凝胶分散液在扫描频率为100 rad/s时,胶态凝胶的储能模量最高可达2×104Pa.这类微凝胶分散液在组织工程支架材料方面有潜在的应用价值.     

侧链含不同功能性羟基的温敏性N-异丙基丙烯酰胺共聚物微凝胶的制备及性能比较

选择含有活性羟基的亲水单体多缩乙二醇单甲基丙烯酸酯(PEGMA)、甲基丙烯酸羟乙酯(HEMA),分别和N-异丙基丙烯酰胺(NIPAM)交联共聚,制备了侧链含有功能性羟基、链长不同的温敏性微凝胶.研究发现,亲水单体HEMA和PEGMA的引入对微凝胶的去溶胀性能有不同的影响,PEGMA的引入使得微凝胶的体积相转变温度升高,微凝胶的去溶胀比随着PEGMA投料比的增加而降低.而HEMA的引入使得微凝胶的体积相转变温度降低;微凝胶的去溶胀比随着HEMA投料比的增加先是增加然后降低,当HEMA的投料比为8mol%时,去溶胀比达到最大.     

浊度法表征温敏性微凝胶体积的相转变行为

以N-异丙基丙烯酰胺(NIPAM)、甲基丙烯酸(MAA)为单体,N,N-亚甲基双丙烯酰胺(MBA)为交联剂,制备了温敏性聚(N-异丙基丙烯酰胺)(PNIPAM)和具有温度、pH敏感性的聚(N-异丙基丙烯酰胺-co-甲基丙烯酸)(PNIPAM-MAA)微凝胶。通过测定不同温度和pH条件下微凝胶浊度变化,表征微凝胶的温度及pH敏感性,描述了NaCl浓度和pH对微凝胶体积相转变温度的影响。同时,测定了微凝胶的临界聚沉浓度及临界絮凝温度,表征了微凝胶的稳定性,讨论了影响微凝胶的稳定性因素。     

疏水改性无规共聚物水凝胶体积相变研究

以偶氮二异丁腈(AIBN)为引发剂,合成了一系列疏水改性的甲基丙烯酸β-羟乙酯(HEMA)无规共聚物水凝胶,研究了离子强度、pH、温度等条件对凝胶体积相变的影响。结果表明,疏水基末端端基的疏水程度决定凝胶体积相变的速率,随着疏水性单体甲基丙烯酸酯烷基链的增长,凝胶的疏水性增强,凝胶的相转变pH向低pH处迁移;温度高于LCST时,分子间的氢键作用减弱,疏水基团间的相互作用加强,凝胶发生体积相变。     

温度和pH双重敏感荧光复合微凝胶制备和表征

通过反相悬浮聚合法制备N-异丙基丙烯酰胺(NIPAM)和甲基丙烯酸(MAA)的共聚微凝胶P(NIPAM-co-MAA), 以其为模板, 利用3-氨丙基三乙氧基硅烷(APTES)在碱性条件下的水解缩合反应, 制备得到了由氨基修饰的P(NIPAM-co- MAA)/SiO₂高分子/无机复合微凝胶, 再通过异硫氰酸荧光素(FITC)与氨基的键和作用, 得到了具有核-壳结构的温度和pH双重敏感荧光复合微凝胶. 通过扫描电子显微镜(SEM)、傅立叶变换红外光谱(FT-IR)、热台偏光显微镜(POM)和共聚焦激光扫描显微镜(CLSM)等手段对复合微凝胶进行了结构和性质表征, 结果表明, 该复合微凝胶对温度和pH均具有良好的响应特性, 并在可见光激发下发出荧光.     

pH响应性阳离子型微凝胶的制备及性质研究

以甲基丙烯酸-(N,N-二甲氨基)乙酯(DMAEMA)和丙烯酸乙酯(EA)为共聚单体, 二甲基丙烯酸乙二醇酯(EGDMA)为交联剂, 采用半连续乳液聚合法, 制备了具有pH响应性的阳离子型微凝胶, 并研究不同聚合条件对所合成的微凝胶性质的影响. 利用透射电子显微镜(TEM)、激光粒度分析仪和流变仪对微凝胶进行一系列表征. 研究了介质pH值对微凝胶的形态、平均粒径、zeta电位、溶液浊度(透光率)的影响, 以及NaCl盐溶液对微凝胶分散体系稳定性的影响. 结果表明, 这类阳离子型微凝胶体系具有良好的pH响应性, 在pH＝7左右发生相转变. 此外, 研究表明不同浓度NaCl溶液对微凝胶的稳定性有一定影响, 临界絮凝浓度约为1.3 mol•L－1.     

PMAA纳米水凝胶的水相制备

利用表面活性剂间的疏水作用以及表面活性剂与单体间的氢键作用,促使甲基丙烯酸(MAA)单体在原位生成的聚甲基丙烯酸甲酯(PMMA)种子乳胶表面的选择性聚合,实现了PMAA纳米水凝胶的水相"绿色"制备。利用动态光散射、傅里叶红外光谱、透射电子显微镜表征了PMAA纳米水凝胶的尺寸、组成、形貌和pH响应性。研究了聚氧乙烯失水山梨醇单月桂酸酯(吐温20)的用量、N,N’-亚甲基双丙烯酰胺(MBA)的用量、MAA的用量和加入方式、十二烷基硫酸钠(SDS)的补加速率等对PMAA纳米水凝胶的尺寸和溶胀性能的影响。结果表明:PMAA纳米水凝胶为核-壳结构;随着MBA用量的减小、吐温20用量的增加、MAA用量的增加,PMAA纳米水凝胶的尺寸和溶胀比均增大;当采用半连续加入MAA时,PMAA纳米水凝胶的尺寸和溶胀比变小;当SDS的补加时间由60min延长到100min时,PMAA纳米水凝胶的尺寸逐渐变小。PMAA纳米水凝胶具有良好的pH响应性,当介质的pH从1增加到6时,其流体力学体积扩张了64倍。     

温度/pH敏感性接枝共聚物水凝胶P(DMAEMA-g-NIPAM)的 合成及性质研究

利用大分子单体技术, 采用自由基溶液聚合合成了温度/pH敏感性聚甲基丙烯酸-N,N-二甲氨基乙酯接枝聚N-异丙基丙烯酰胺[P(DMAEMA-g-NIPAM)]水凝胶. 用红外光谱及扫描电镜对凝胶的组成及形貌进行了表征. 凝胶的去溶胀和溶胀动力学研究表明, 所合成的凝胶具有温度和pH敏感性. 与传统的聚丙烯酸系水凝胶相比, P(DMAEMA-g- NIPAM)具有相反的pH敏感性; P(DMAEMA-g-NIPAM)凝胶在55 ℃时具有较快的去溶胀速率, 随着凝胶中接枝链PNIPAM量的增加, 凝胶的去溶胀速率加快.     

温度、pH敏感性核壳结构微凝胶的制备及性质

以无皂乳液分步聚合的方法, 将N-异丙基丙烯酰胺(NIPAM)与N,N-亚甲基双丙烯酰胺(MBA)交联反应3 h, 制得种子乳液, 再向种子乳液中加入甲基丙烯酸(MAA)功能性单体继续反应2 h, 制备了具有温度、pH敏感性的核壳结构微凝胶. 通过透射电子显微镜(TEM)、红外光谱(IR)等表征了微凝胶外貌形态及结构组成, 动态光散射(DLS)测定了微凝胶粒径响应热、pH的变化及微凝胶Zeta电位的变化. 结果表明凝胶形貌为异型核壳结构; Zeta电位与微凝胶粒径随温度、pH变化相关.     

核壳结构葡萄糖敏感微凝胶的制备

用先合成聚N-异丙基丙烯酰胺(PNIPAM)微凝胶核再包一层N-异丙基丙烯酰胺/丙烯酸共聚物(P(NIPAM-co-AA))壳的办法合成了一系列核壳结构微凝胶.微凝胶壳层厚度随投入的壳储备溶液的增加而增加.研究了pH=3.5时核壳微凝胶的温敏体积相转变行为.由于PNIPAM核和P(NIPAM-co-AA)壳的相转变温度很接近,因此只观察到一个相转变.在EDC催化下使3-氨基苯硼酸与壳层中的羧基反应,将苯硼酸基(PBA)引入微凝胶,得到核为PNIPAM、壳为P(NIPAM-co-AMPBA)的核壳结构微凝胶.改性后的微凝胶表现出3个体积相转变过程.其中第一个对应于P(NIPAM-co-AMPBA)壳层的体积相转变.第二和第三个则是PNIPAM核的相转变过程.由于在沉淀聚合时交联剂BIS反应性更大,PNIPAM核结构不均一,形成BIS含量高的"核"和BIS含量低的"壳".BIS含量低的"壳"被一层疏水的P(NIPAM-co-AMPBA)壳包裹,拉大了其与"核"的相转变温度的差别,因此随着温度升高表现出两个相转变过程.PBA改性的微凝胶同样表现出葡萄糖敏感性,但在葡萄糖存在下溶胀度的改变较小.     

Adsorption and controlled release of Chlortetracycline HCl by using multifunctional polymeric hydrogels

Adsorption and controlled release of Chlortetracycline HCl to and from multifunctional polymeric materials (HEMA/MAA) hydrogels were investigated. P(HEMA/MAA) hydrogels were synthesized by gamma radiation-induced copolymerization of 2-hydroxyethylmethacrylate (HEMA) and methacrylic acid (MAA) in aqueous solution. The influence of copolymer composition and pH value of the surrounding medium on the type of water diffusion into the glassy polymer were discussed. Drug, Chlortetracycline HCl containing hydrogels, with different drug concentration to polymer ratios, was loaded by direct adsorption method. The influence of MAA content in the gel on the adsorption capacities of hydrogel was studied. Chlortetracycline HCl adsorption capacity of hydrogels was found to increase from 8 to 138 mg Chlortetracycline HCl per gram dry gel with increasing amount of MAA in the gel system and drug concentration. The effect of pH on the releasing behavior of Chlortetracycline HCl from gel matrix was investigated. In vitro drug release studies in different buffer solutions show that the basic parameters affecting the drug release behavior of hydrogel are the pH of the solution and MAA content of hydrogel.     

Copolymerization of 2‐isothiocyanatoethyl methacrylate and 2‐hydroxyethyl methacrylate or methacrylic acid based on a nucleophile‐tolerant property of the isothiocyanato group

Radical copolymerizations of 2‐isothiocyanatoethyl methacrylate (ITEMA) and 2‐hydroxyethyl methacrylate (HEMA) or methacrylic acid (MAA) were examined, and fundamental properties of the obtained copolymers were investigated. The copolymerizations of various ITEMA/HEMA or ITEMA/MAA compositions proceeded effectively in THF or DMF by using 2,2′‐azobisbutyronitrile (AIBN) as an initiator, keeping the isothiocyanato groups and hydroxyl or carboxyl groups unchanged. Glass transition temperatures (T_g)s of poly(ITEMA‐co‐HEMA)s ranged from 68 to 100 °C, and they were thermally stable up to 200 °C. Meanwhile, T_gs of poly(ITEMA‐co‐MAA)s (ITEMA/MAA = 91/9, 76/24) were determined to be 91 and 109 °C, respectively. However, poly(ITEMA‐co‐MAA)s were thermally unstable, and significant weight loss was observed around 180 °C, which may be due to an addition of carboxyl groups to isothiocyanato groups followed by an elimination of COS to form amide structure in the copolymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5221–5229     

Microgels containing methacrylic acid: effects of composition on pH-triggered swelling and gelation behaviours

pH-responsive microgels are cross-linked polymer colloids that swell when the pH approaches the pK _a of the particles. In this work, we present a comprehensive investigation of pH-triggered particle swelling and gel formation for a range of microgels containing methacrylic acid (MAA). The microgels investigated have the general composition poly(A/MAA/X), where A and X are the primary co-monomer and cross-linking monomer, respectively. The primary co-monomers were methyl methacrylate (MMA), ethyl acrylate (EA) or butyl methacrylate. The cross-linking monomers were either butanediol diacrylate (BDDA) or ethyleneglycol dimethacrylate (EGDMA). The microgels were studied using scanning electron microscopy, photon correlation spectroscopy (PCS) and dynamic rheology measurements. Gel phase diagrams were also constructed. The particles swelled significantly at pH values greater than approximately 6.0. It was shown that poly(EA/MAA/X) microgels swelled more strongly than poly(MMA/MAA/X) microgels. Furthermore, greater swelling occurred for particles prepared using EGDMA than BDDA. Concentrated dispersions of all the microgels studied exhibited pH-triggered gel formation. It was found that the fluid-to-gel transitions for the majority of the six microgel dispersions investigated could be explained using PCS data. In those cases, gelation was attributed to a colloidal glass transition. Interestingly, the microgels that were considered to have the highest hydrophobic content gelation occurred under conditions where little particle swelling was evident from PCS. The data presented show that gelled poly(EA/MAA/BDDA) and poly(MMA/MAA/EGDMA) microgel dispersions have the strongest elasticities at pH = 7.     

Microgel particles containing methacrylic acid: pH-triggered swelling behaviour and potential for biomaterial application

pH-responsive microgels are crosslinked polymer particles that swell when the pH approaches the pK(a) of the ionic monomer incorporated within the particles. In recent work from our group it was demonstrated that the mechanical properties of degenerated intervertebral discs (IVDs) could be restored to normal values by injection of poly(EA/MAA/BDDA) (ethylacrylate, methacrylic acid and butanediol diacrylate) microgel dispersions [J.M. Saunders, T. Tong, C.L. Le Maitre, T.J. Freemont, B.R. Saunders, Soft Matter 3 (2007) 486]. In this work we report the pH dependent swelling and rheological properties of poly(MMA/MAA/EGDMA) (methylmethacrylate and ethyleneglycol dimethacrylate) microgel dispersions. This system was investigated because it contains monomers that are already used as biomaterials. The poly(MMA/MAA/EGDMA) particles exhibit pH-triggered volume swelling ratios of up to ca. 250. The swelling onset for these particles occurs at pH values greater than ca. 6.0. A pK(a) for these particles of ca. 6.7 is consistent with titration and swelling data. Fluid-to-gel phase diagrams for concentrated poly(MMA/MAA/EGDMA) dispersions were determined as a function of polymer volume fraction and pH using tube-inversion measurements. The rheological properties for the gelled microgel dispersions were investigated using dynamic rheology measurements. The elastic modulus data for the poly(MMA/MAA/EGDMA) gelled dispersions were compared to data for poly(EA/MAA/BDDA) microgels. A similar pH-dependence for the elastic modulus was apparent. The maximum elastic modulus was achieved at a pH of about 7.0. The elastic modulus is an exponentially increasing function of polymer volume fraction at pH 7.0. Preliminary cell challenge experimental data are reported that indicate that gelled poly(MMA/MAA/EGDMA) microgel dispersions are biocompatible with cells from human intervertebral discs. However, the duration over which these experiments could be performed was limited by gradual redispersion of the gelled microgel dispersions. Based on the results presented it is suggested that poly(MMA/MAA/EGDMA) microgel would be a good candidate as a biomaterial for structural support of soft connective tissues.     

接枝微球PMAA-HEMA/NVP对溶菌酶的吸附行为与吸附机理

采用反相悬浮聚合法制备了甲基丙烯酸羟乙酯(HEMA)与N-乙烯基吡咯烷酮(NVP)的交联共聚微球HEMA/NVP,然后采用"接出"法,实施了甲基丙烯酸(MAA)在交联微球表面的接枝聚合,制得了接枝微球PMAA-HEMA/NVP.以溶菌酶(LYZ)为模型碱性蛋白,深入研究了接枝微球PMAA-HEMA/NVP对碱性蛋白的吸附性能与吸附机理.测定了微球PMAA-HEMA/NVP的zeta电位,考察了PMAA接枝度、介质pH值及离子强度等因素对体系吸附性能的影响.结果表明,在较大的pH范围内,接枝微球PMAA-HEMA/NVP的zeta电位为绝对值较大的负值,即其表面携带有高密度的负电荷.在强静电相互作用的驱动下,接枝微球PMAA-HEMA/NVP对溶菌酶表现出很强的吸附能力.随介质pH值的增高,接枝微球对溶菌酶的吸附容量呈现先增大后减小的变化趋势,在与溶菌酶等电点接近的pH值处(pH=9),具有最大的吸附容量(90mg.g-1);离子强度对接枝微球的吸附能力也有较大的影响,当pH9时,溶菌酶吸附容量随NaCl浓度的增高而减小;当pH9时,吸附容量随NaCl浓度的增高而增大.     

Novel porphyrin-incorporated hydrogels for photoactive intraocular lens biomaterials

Novel surface-modified hydrogel materials have been prepared by binding charged porphyrins TMPyP (tetrakis(4-N-methylpyridyl)porphyrin) and TPPS (tetrakis(4-sulfonatophenyl)porphyrin) to copolymers of HEMA (2-hydroxyethyl methacrylate) with either MAA (methacrylic acid) or DEAEMA (2-(diethylamino)ethyl methacrylate). The charged hydrogels display strong electrostatic interactions with the appropriate cationic or anionic porphyrins to give materials which are intended to be used to generate cytotoxic singlet oxygen (1O2) on photoexcitation and can therefore be used to reduce postoperative infection of the intraocular hydrogel-based replacement lenses that are used in cataract surgery. The UV/vis spectra of TMPyP in MAA:HEMA copolymers showed a small shift in the Soret band and a change from single exponential (161 micros) triplet decay lifetime in solution to a decay that could be fitted to a biexponential fit with two approximately equal components with tau = 350 and 1300 micros. O2 bubbling reduced the decay to a dominant (90%) component with a much reduced lifetime of 3 micros and a minor, longer lived (20 micros) component. With D2O solvent the 1O2 lifetime was measured by 1270 nm fluorescence as 35 micros in MAA:HEMA, compared to 67 mus in solution, although absorbance-matched samples showed similar yield of 1O2 in the polymers and in aqueous solution. In contrast to the minor perturbation in photophysical properties caused by binding TMPyP to MAA:HEMA, TPPS binding to DEAEMA:HEMA copolymers profoundly changed the 1O2 generating ability of the TPPS. In N2-bubbled samples, the polymer-bound TPPS behaved in a similar manner to TMPyP in its copolymer host; however, O2 bubbling had only a very small effect on the triplet lifetime and no 1O2 generation could be detected. The difference in behavior may be linked to differences in binding in the two systems. With TMPyP in MAA:HEMA, confocal fluorescence microscopy showed significant penetration of the porphyrin into the core of the polymer film samples (>150 microm). However, for TPPS in DEAEMA:HEMA copolymers, although the porphyrin bound much more readily to the polymer, it remained localized in the first 20 microm, even in heavily loaded samples. It is possible that the resulting high concentration of TPPS may have cross-linked the hydrogels to such an extent that it significantly reduced the solubility and/or diffusion rate of oxygen into the doped polymers. This effect is significant since it demonstrates that even simple electrostatic binding of charged porphyrins to hydrogels can have an unexpectedly large effect on the properties of the system as a whole. In this case it makes the apparently promising TPPS/DEAEMA:HEMA system a poor candidate for clinical application as a postoperative antibacterial treatment for intraocular lenses while the apparently equivalent cationic system TMPyP/MAA:HEMA displays all the required properties.     

A study of poly(butadiene/methacrylic acid) dispersions: from pH-responsive behaviour to the effects of added Ca2+

This study investigates the effects of added Ca(2+) on the properties of poly(Bd/MAA) dispersions (1,3-butadiene and methacrylic acid) and considers the effect of particle composition on the pK(a). Four latex dispersions are considered in detail. These include poly(Bd/6MAA) and poly(Bd/20MAA) which contain, 6 and 20 wt% MAA, respectively, based on the total monomer mass used for dispersion preparation. Two model systems are also used for comparison. These are poly(Bd) and poly(EA/33MAA/BDDA) (EA and BDDA are ethyl acrylate and butanediol diacrylate). The latter is a well-studied model pH-responsive microgel. The apparent pK(a) of the poly(Bd/MAA) dispersions was determined from potentiometric titrations and found to increase with Bd content. The pH-dependence of the particle size was studied using photon correlation spectroscopy. Electrophoretic mobility measurements were also used. The hydrodynamic diameters and mobilities exhibited major changes as the pH approached the pK(a) for the particles. The critical coagulation concentrations were also measured. The results indicate that Ca(2+) caused pronounced dispersion instability at low pH. Moreover, Ca(2+) prevents swelling of the poly(Bd/MAA) particles at high pH. It was found that efficient ionic binding of all of the RCOO(-) groups within the poly(Bd/20MAA) particles occurred when the mole ratio of RCOO(-) to Ca(2+) was less than or equal to 2.0. Consideration of all the data leads to the suggestion that poly(Bd/MAA) particles have a core-shell structure. It is suggested that the particle core contains mostly poly(Bd) and that the shell is comprised of lightly crosslinked poly(Bd-co-MAA) copolymer.     

Charged polystyrene nanoparticles: role of ionic comonomers structures

Emulsion copolymerizations of styrene were carried out with four structurally different ionic comonomers namely acrylic acid (AAc), methacrylic acid (MAA), 2-hydroxyethyl methacrylate (HEMA), and sodium styrene sulfonate (NaSS) to study the effect of monomer structure on the copolymerization kinetics and size, morphology, charge density, and the self-assembly of the particles. The copolymerization kinetics was found to be highly dependent upon the ionic comonomer structure, and the nature of this dependence altered from homogeneous to micellar nucleation regime. The decrease in particle size (D) with increasing surfactant concentration (S) was observed in all the cases; however, the exponents of D vs. S were not similar for all the cases. In the homogeneous nucleation regime, exponents followed the order as AAc (0.446) > MAA (0.396) > NaSS (0.252) > HEMA (0.241), whereas the order was almost reversed in the micellar nucleation regime as NaSS (0.406) > HEMA (0.228) > AAc (0.206) > MAA (0.172). The hydrophobic/hydrophilic character and the steric factors were found to be the driving force for the variation in D vs. S exponents with ionic comonomer structure. The presence of charges on the particle surface contributed by the ionic comonomers triggered the self-assembly of the particles upon sedimentation and diffracted visible light obeying Bragg's law.     

Synthesis and characterization of new cross-linked terpolymer systems containing silyl group

A series of acrylic terpolymers containing silyl pendant groups was prepared by free radical cross-linking copolymerization. Me₃Si, Et₃Si and t-BuMe₂Si together with cubane-1, 4-dicarboxylic acid (CDA) were covalently linked with 2-hydroxyethyl methacrylate (HEMA). The silyl-linked HEMA are abbreviated as TMSiEMA, TESiEMA and TBSiEMA respectively. Cubane-1, 4-dicarboxylic acid (CDA) linked to two HEMA group is the cross-linking agent (CA). Free radical cross-linking terpolymerization of the methyl methacrylate (MMA) and methacrylic acid (MAA) with two different molar ratios of organosilyl monomers and CA was carried out at 60–70 ^∘C. The compositions of the cross-linked three-dimensional polymers were determined by FT-IR spectroscopy. The glass transition temperature (Tg) of the network polymers was determined calorimetrically. The Tg of network terpolymers increases with increasing of cross-linking degree. Equilibrium swelling studies were carried out in enzyme-free simulated gastric and intestinal fluids (SGF and SIF, respectively). The gels swelled more in SIF than in SGF. The swelling behaviour of the copolymers was dependent on the content of MAA groups and caused a decrease in gel swelling in pH 1 or an increase in gel swelling in pH 7.4. Based on the great difference in swelling ratio at pH 1 and 7.4 for P-1, P-6 and P-10 appear to be good candidates for colon-specific drug delivery.