Ba0.4Sr0.6Co1-xFexO3-δ系阴极材料的制备和表征

采用甘氨酸-硝酸盐(GNP)法合成了中温固体氧化物燃料电池阴极材料Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ(x=0.0～0.8)系列粉体。利用XRD和SEM对材料的结构和微观形貌进行分析,用直流四端子法测量了烧结陶瓷体在中温(450～800 ℃)范围内的电导率。结果表明,制备的样品为单一钙钛矿相,随着Fe含量增加,XRD衍射峰值向高角度方向稍有偏移。电导率随着温度及Fe含量的变化出现极大值,在x＜0.2时,Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ系列烧结体在中温(450～800 ℃)区的电导率,随Fe掺入量的增大而增大,x=0.2样品的电导率最高,800 ℃时达244.7 S·cm^-1,远超过文献报道值,进一步增大Fe含量导电性能变差。     

Ba0.98Bi0.02(Ti0.9Zr0.1)1-xCuxO3陶瓷的介电性能、弛豫行为与结晶化学特性

采用固相合成法, Bi3+作施主掺杂A位, Cu₂₊作受主掺杂B位, 制备了Ba_0.98Bi_0.02(Ti_0.9Zr_0.1)_1-xCu_xO₃(x=0, 0.01, 0.02, 0.03)陶瓷样品。借助XRD、LCR等研究了该陶瓷的结构与介电性能。结果表明:当x=0.03时, 陶瓷样品出现第二相。通过GULP模拟, 缺陷偶极子的稳定性从低到高依次为:[2Bi_Ba^·+V_Ba"]、[2Bi_Ba^·+Cu_Ti/Zr"]、[Cu_Ti/Zr"+V_O^··], 结合实验可知:介电弛豫程度与晶体中缺陷偶极子的存在形式相关, 其中x=0.01时, 晶体中以[2Bi_Ba^·+Cu_Ti/Zr"]为主。随Cu₂₊掺杂量的增加, 介电常数增加, 介电常数与B位键价和呈反比变化、与八面体BO₆的体积呈正比变化。     

(Zn1-xMnx)C2O4·2H2O在空气中的热分解动力学研究

用热分析（TG-DTG/DTA）、X射线衍射（XRD）技术和透射电镜（TEM）研究了固态物质Zn_1-xMn_xC₂O₄•2H₂O在空气中热分解的过程。热分析结果表明，Zn_1-xMn_xC₂O₄•2H₂O在空气中分两步分解，其失重率与理论计算失重率相吻合。 XRD和TEM结果表明，Zn_1-xMn_xC₂O₄•2H₂O分解的最终产物为Zn_1-xMn_xO,其颗粒大小约为10-13 nm。在非等温条件下对Zn_1-xMn_xC₂O₄•2H₂O的热分解动力学进行了分析。用Friedman法和Flynn-Wall-Ozawa(FWO)法求取了分解过程的活化能E，并用多元线性回归给出了可能的机理函数。Zn_1-xMn_xC₂O₄•2H₂O两步热分解的活化能分别为155.7513 kJ/mol 和215.9397 kJ/mol。     

阴极材料LaFe0.8-xCuxNi0.2O3的合成和烧结性能

LaFe_0.8-xCu_xNi_0.2O₃ (x=0.0~0.2) (LFCN), a new cathode material of solid oxide fuel cell (SOFC), was synthesized by Co-precipitation method using sodium bicarbonate. The lattice structures of samples with different x contents were characterized by XRD. Porosity and density of the porous LaFe_0.8-xCu_xNi_0.2O₃ (x=0.0~0.1) as a function of sintering temperature were investigated. It was found that the orthorhombic structure could be formed after calcination at 900 ℃ for 4 h. The particle size of LFCN was about 350 nm. The density of the porous LFCN increased with sintering temperature, but the opposite was true for the porosity. On the other hand, at the same sintering temperature, the porosity of LaFe_0.8-xCu_xNi_0.2O₃ (x=0.0~0.1) decreased with increasing x contents. It is indicated that the dopant of Cu on LaFe_0.8Ni_0.2O₃ can facilitate the sintering of the materials. After sintering at 1 100 ℃ for 4 h, the porous LaFe_0.7Cu_0.1Ni_0.2O₃ was still with appropriate structure, and its porosity was 29%.     

电荷补偿对Ba2ZnGe2O7：Bi3+荧光粉发光性质的影响

采用高温固相法制备了2个系列的荧光粉样品：Ba_2-xZnGe₂O₇：xBi³⁺（系列Ⅰ）和Ba_1.994-yK_yZnGe₂O₇：0.006Bi³⁺（系列Ⅱ）。X射线衍射（XRD）测试结果表明,少量Bi³⁺、K⁺的掺杂不会明显改变材料的物相结构。样品的荧光光谱测试结果表明,虽然2个系列样品的发光光谱都随组成成分变化有少量变化,但发光颜色基本上均为黄绿色。在358 nm的激发下,荧光粉的发射光谱呈现一个峰值在500 nm的宽发射带,归属于³P₁→¹S₀能级跃迁。在500 nm监测下,荧光粉的最强激发峰位于358 nm,归属于¹S₀→³P₁能级跃迁,此外还有一个位于320 nm的肩峰归属于O^2--Bi³⁺电荷转移带。系列Ⅰ样品的光谱数据结果指出,Bi³⁺的最佳掺杂量x为0.006。在该基质中,Bi³⁺掺杂取代Ba²⁺属于不等价取代,会在晶格中产生Ba²⁺空位或间隙O^2-,对材料的发光强度产生负面影响。对此,采用K⁺与Bi³⁺协同掺杂起到电荷补偿的作用,填补Ba²⁺空位或捕获间隙O^2-缺陷。空位被填补或间隙被捕获均减少了晶格畸变,从而使发光强度明显提高。系列Ⅱ样品的光谱数据表明,完全电荷补偿的荧光粉样品相比于没有掺K⁺的样品,其发光强度提高了约2.5倍。     

电荷补偿对Ba2ZnGe2O7∶Bi3+荧光粉发光性质的影响

采用高温固相法制备了2个系列的荧光粉样品：Ba_2-xZnGe₂O₇∶xBi³⁺(系列Ⅰ)和Ba_1.994-yK_yZnGe₂O₇∶0.006Bi³⁺(系列Ⅱ)。X射线衍射(XRD)测试结果表明,少量Bi³⁺、K⁺的掺杂不会明显改变材料的物相结构。样品的荧光光谱测试结果表明,虽然2个系列样品的发光光谱都随组成成分变化有少量变化,但发光颜色基本上均为黄绿色。在358 nm的激发下,荧光粉的发射光谱呈现一个峰值在 500 nm 的宽发射带,归属于 ³P₁→^1S₀能级跃迁。在 500 nm 监测下,荧光粉的最强激发峰位于 358 nm,归属于¹S₀→³P₁能级跃迁,此外还有一个位于320 nm的肩峰归属于O^2--Bi³⁺电荷转移带。系列Ⅰ样品的光谱数据结果指出,Bi³⁺的最佳掺杂量x为0.006。在该基质中,Bi³⁺掺杂取代Ba²⁺属于不等价取代,会在晶格中产生Ba²⁺空位或间隙O^2-,对材料的发光强度产生负面影响。对此,采用K⁺与Bi³⁺协同掺杂起到电荷补偿的作用,填补Ba²⁺空位或捕获间隙O^2-缺陷。空位被填补或间隙被捕获均减少了晶格畸变,从而使发光强度明显提高。系列Ⅱ样品的光谱数据表明,完全电荷补偿的荧光粉样品相比于没有掺K⁺的样品,其发光强度提高了约2.5倍。     

BaCe0.8-xNbxGd0.2O3-δ(0≤x≤0.45)的制备及性能研究

采用高温固相反应法制备了质子导体BaCe_0.8-xNb_xGd_0.2O_3-δ(0≤x≤0.45)。结合XRD、SEM、EIS等技术对其物相、微观形貌、稳定性及电导率进行了研究。结果表明,在1 600 ℃烧结5 h制备的质子导体BaCe_0.8-xNb_xGd_0.2O_3-δ(0≤x≤0.45)均能保持主相为斜方晶的钙钛矿结构。Nb的加入可明显提高烧结样品的致密性及在CO₂和水蒸气气氛下的稳定性。在湿润H₂/Ar(0.4%,V/V)气氛中800 ℃下,x=0.1样品的电导率为5.73 mS·cm^-1,电导活化能为0.35 eV,与x=0的样品相当。     

低温合成超导体Ba1-xKxBiO3

先以BaCO3和Bi2O3为原料由传统的固相反应制备纯BaBiO3,然后在低温下将用KOH-KF熔盐处理这样的拓扑反应合成了Ba1-xKxBiO3超导体.所有样品均进行了粉末X射线衍射(XRD)和磁性表征.XRD结果表明,所得Ba1-xKxBiO3样品均为纯相,且均可用赝立方晶胞指标化.磁性测量表明所有样品具有超导电性,最高超导转变温度(Tc)为30.6 K.讨论了反应时间、前驱体与熔盐质量比对超导转变温度的影响.最佳的反应条件为:反应温度450°C,反应时间4 h,BaBiO3:KOH:KF质量比1:5:2.5.     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

La1-xSrxFeO3-δ系钙钛矿材料的表征和性能

采用甘氨酸-硝酸盐(GNP)法合成了中温固体氧化物燃料电池阴极材料La_1-xSr_xFeO_3-δ(x=0.0~0.6)系列粉体。用FTIR、TG-DTA、XRD等对产物形成过程及结晶学特征进行了研究，考察了合成样品与Sm_0.2Ce_0.8O_1.9(SDC)的化学相容性；利用碘滴定法测定了该系列产物中Fe元素的平均表观化合价和氧的非化学计量值。结果表明，所合成的系列样品均形成具有ABO₃型结构的钙钛矿固溶体。随A位取代Sr含量的增加，IR谱图上560 cm^-1附近B-O键伸缩振动的红外吸收峰蓝移，意味着钙钛矿产物中Fe-O键的共价性成分增强。实验还发现，Fe元素的平均化合价先随样品中Sr含量的增加而升高，并以La_0.6Sr_0.4FeO_3-δ样品达最高，而后降低；样品中氧的非化学计量值则随掺Sr量的增加单调增大。四探针法电导测量结果表明，在x≤0.4时，La_1-xSr_xFeO_3-δ系列陶瓷烧结体在中温(450~800 ℃)区的电导率，随Sr掺入量的增大而增大，La_0.6Sr_0.4FeO_3-δ样品的电导率最高，进一步增大Sr含量导电性能变差。在低温段，样品的导电行为符合小极化子导电机制。该系列材料与SDC电解质材料具有良好的化学相容性。     

Effect of BaBiO3 and Ba0.6K0.4BiO3 additives on the rechargeability of manganese oxide cathodes in alkaline cells

The effect of the incorporation of small amounts (1–5 wt%) of semiconducting BaBiO₃ and metallic Ba_0.6K_0.4BiO₃ additives on the rechargeability of electrolytic manganese dioxide (EMD) cathodes in alkaline cells in the one-electron regime has been investigated. Both the BaBiO₃ and Ba_0.6K_0.4BiO₃ additives lead to better cyclability compared to the previously known binary oxide additive Bi₂O₃. X-ray diffraction patterns recorded before and after 30 cycles as well as cyclic voltammograms recorded after first and 30 cycles reveal that the better cyclability in the presence of BaBiO₃ and Ba_0.6K_0.4BiO₃ additives is due to the suppression of the formation of unwanted, electrochemically inactive birnessite and hausmannite phases and a shifting of the second-electron capacity of Mn to higher potentials.     

中温固体氧化物燃料电池La1.6Sr0.4Ni1-xCuxO4阴极材料的制备及电化学性能

采用甘氨酸-硝酸盐法合成了中温固体氧化物燃料电池阴极材料La_1.6Sr_0.4Ni_1-xCu_xO₄ (x=0.2, 0.4, 0.6,0.8), 利用X射线衍射(XRD)和扫描电子显微镜(SEM)对其结构和微观形貌进行了表征. 结果表明, 该阴极材料与固体电解质Ce_0.9Gd_0.1O_1.95(CGO)在1000 °C烧结时不发生化学反应, 且烧结4 h 后, 二者之间可形成良好的接触界面. 利用电化学交流阻抗谱技术对阴极材料的电化学性能进行研究, 结果显示, 当Cu离子掺杂量(x)为0.6 时, La_1.6Sr_0.4Ni_0.4Cu_0.6O₄阴极具有最小的极化电阻, 在空气中当测试温度为750 °C时, 极化电阻为0.35 Ω·cm². 在不同氧分压条件下电化学阻抗谱分析结果表明, 电极上的两个氧还原反应主要包含氧离子从三相界面向电解质CGO 转移的过程和电荷的迁移过程, 其中电荷的迁移过程为电极反应的速率控制步骤.La_1.6Sr_0.4Ni_0.4Cu_0.6O₄电极在空气中700 °C和阴极电流密度为45 mA·cm^-2时, 阴极过电位为45 mV. 本研究的初步结果表明La_1.6Sr_0.4Ni_1-xCu_xO₄材料是一种电化学性能较为优良的新型中温固体氧化物燃料电池(IT-SOFC)阴极材料.     

BaFeO3-x与Cu-ZSM-5耦合催化剂的NOx储存还原性能

为替代传统的贵金属基NO_x储存还原（NSR）催化剂,本文设计并制备了不含贵金属的BaFeO_3-x+Cu-ZSM-5 耦合催化剂,用于催化消除稀燃发动机尾气中的NO_x. 在稀燃阶段,NO在BaFeO_3-x催化剂上发生了氧化和储存反应;在富燃阶段,从BaFeO_3-x催化剂中脱附出来未能消除的NO_x被置于其后的Cu-ZSM-5催化剂进一步催化消除. 实验结果表明,BaFeO_3-x+Cu-ZSM-5 耦合催化剂的工作温度窗口被拓宽到250-400 ℃,同时NO_x消除性能得到了显著提高：NO_x转化率最高可达98%,N₂选择性接近100%.     

室温电化学沉积Ba1-xCaxMoO4多晶固溶体薄膜

近年发展起来的制备功能薄膜的电化学沉积技术,是软溶液工艺路线(Soft Solution Processing简记为SSP)中的重要技术[1]。与传统的薄膜制备技术相比,电化学沉积技术在反应控制、形貌控制、沉积速度、能量消耗、环境影响、薄膜晶化以及沉积设备等方面都有较明显的优势,同时避免了     

Composition-induced structural phase transitions in the (Ba1−xLax)2In2O5+x (0?x?0.6) system

Composition-induced structural phase changes across the high temperature, fast oxide ion conducting (Ba_1−xLa_x)₂In₂O_5+x, 0?x?0.6, system have been carefully analysed using hard mode infrared (IR) powder absorption spectroscopy, X-ray powder diffraction and electron diffraction. An orthorhombic brownmillerite to three-dimensionally disordered cubic perovskite phase transition in this system is signalled by a drastic change in slope of both wavenumber and average line widths of IR spectra as a function of composition. Some evidence is found for the existence of an intermediate tetragonal phase (previously reported to exist from electron diffraction data) around x∼0.2. The new spectroscopic data have been used to compare microscopic and macroscopic strain parameters arising from variation in composition. The strain and spectroscopic data are consistent with first-order character for the tetragonal→orthorhombic transition, while the cubic→tetragonal transition could be continuous. Differences between the variation with composition of spectral parameters and of macroscopic strain parameters are consistent with a substantial order/disorder component for the transitions. There is also evidence for precursor effects within the cubic structure before symmetry is broken.     

Cs取代对Ni-H3PW12O40/SiO2催化剂结构性质和催化性能的影响

采用两步浸渍法和载体上的原位反应制备了一系列Cs部分取代的Ni-Cs_xH_3-xPW₁₂O₄₀/SiO₂催化剂,并用N₂吸附比表面积测定(BET)、电感耦合等离子体发射光谱(ICP)、X射线衍射(XRD)、拉曼光谱(Raman)、原位X射线衍射(in situ XRD)、NH₃程序升温脱附(NH₃-TPD)、H₂程序升温还原(H₂-TPR)、H₂程序升温脱附(H₂-TPD)、吡啶吸附傅里叶变换红外(FTIR)光谱等分析测试技术对催化剂进行了表征. 以正癸烷为模型化合物,对催化剂的加氢裂化性能进行了评价. 结果表明,8%Ni-50%Cs_1.5H_1.5PW/SiO₂催化剂具有最高的C₅₊收率,明显优于8%Ni-50%H₃PW/SiO₂催化剂和工业催化剂. 随着Cs 在Cs_xH_3-xPW中比例的增加,正癸烷的转化率逐渐降低,而C₅₊选择性则逐渐提高. 当催化剂具有合适的孔径时,选择性的提高是由于催化剂酸性的减弱,而转化率的降低则是由于催化剂加氢能力的减弱.     

La1-xCaxMnO3纳米颗粒的制备及氧还原催化性能

本文采用溶胶凝胶法制备了一系列不同Ca含量的钙钛矿型氧化物La1-xCaxMnO3(x=0~0.4)纳米颗粒,X射线粉末衍射及精修、扫描电镜表征显示其相纯度和结晶度高,颗粒平均粒径约40 nm。在0.1 mol.L-1KOH水溶液中进行的氧还原电催化性能测试显示,La0.7Ca0.3MnO3样品催化活性最高,表观电子转移数接近4,还原电流密度与Pt/C催化剂相当,而催化稳定性优于Pt/C。进一步研究了La1-xCaxMnO3样品中Mn价态、晶胞参数的改变对氧还原催化活性的影响,结果表明当x=0.3时,催化剂中Mn处于混合价态,Mn-O键长适中,最有利于电催化反应。     

La1-xCaxMnO3纳米颗粒的制备及氧还原催化性能

本文采用溶胶凝胶法制备了一系列不同Ca含量的钙钛矿型氧化物La_1-xCa_xMnO₃(x=0~0.4)纳米颗粒, X射线粉末衍射及精修、扫描电镜表征显示其相纯度和结晶度高, 颗粒平均粒径约40 nm。在0.1 mol·L^-1 KOH水溶液中进行的氧还原电催化性能测试显示, La_0.7Ca_0.3MnO₃样品催化活性最高, 表观电子转移数接近4, 还原电流密度与Pt/C催化剂相当, 而催化稳定性优于Pt/C。进一步研究了La_1-xCa_xMnO₃样品中Mn价态、晶胞参数的改变对氧还原催化活性的影响, 结果表明当x=0.3时, 催化剂中Mn处于混合价态, Mn-O键长适中, 最有利于电催化反应。     

A TEM, XRD, and crystal chemical investigation of oxygen/vacancy ordering in (Ba1−xLax)2In2O5+x, 0x0.6

A careful TEM and XRD study of the (Ba_1−xLa_x)₂In₂O_5+x, 0x0.6, ‘defect-perovskite’-type solid solution has been carried out. A well-defined structural phase transition is shown to occur between x=0.1 and 0.2 from the orthorhombic brownmillerite structure type on the low x side to a multiple twinned, tetragonal 1×1×2 perovskite-related superstructure phase on the high x side at x=0.2. This phase transition correlates with an important phase transition previously observed in electrical conductivity versus temperature measurements. The existence of additional satellite reflections close to the regions of reciprocal space was found to be typical of all (Ba_1−xLa_x)₂In₂O_5+x specimens, although their intensity relative to the parent Bragg reflections systematically reduces as x increases. As x increases beyond 0.2, the -type satellite reflections initially become weaker and rather more diffuse for x=0.3 before splitting into pairs of rather weak and somewhat diffuse incommensurate satellite reflections for x=0.4 and beyond. An interpretation in terms of oxygen vacancy ordering and associated structural relaxation is given. Additional structured diffuse scattering is also observed and a tentative explanation in terms of Ba/La ordering and associated local strain distortions put forward.     

Synthesis, Characterization and Humidity Sensitive Properties of Nanocrystalline LaCoxFe1-xO3

The nanocrystalline LaCo_xFe_1-xO₃ with different concentrations of Co was prepared by polyethylene glycol (PEG) sol-gel method and characterized by differential thermal analysis and thermal gravimetric analysis (DTA-TGA), X-ray diffraction (XRD), and scanning electron microscope (SEM). It was found that the crystal structure of perovskite-type could be obtained at 600 °C, and the concentration of Co had significant effects on the solid-state reaction and the average particle size of the obtained nanocrystals. Furthermore, the humidity-sensitive properties of nanocrystalline LaCo_xFe_1-xO₃ were investigated, and it was found that LaCo_0.3Fe_0.7O₃ exhibited higher sensitivity to humidity compared with other samples. The addition of Na₂CO₃ improved the humidity-sensitive properties of this sample, and made its response to humidity good in the whole humidity range of 11%-95% relative humidity (RH).