聚丙烯共混物一步法反应共混增容的研究

研究了影响聚丙烯／（丙烯腈 苯乙烯）共聚物（ＰＰ／ＡＳ）合金反应挤出生成的各项因素,发现在过氧化二异丙苯（ＤＣＰ）存在的条件下进行反应共混可以发生接枝反应,生成ＰＰ与ＡＳ的相互接枝物．接枝物的生成显著地细化了分散相粒子,改善了合金相形态．为抑制反应共混过程中聚丙烯的降解,同时促进接枝反应,在ＰＰ／ＡＳ／ＤＣＰ反应共混中加入了含适量双键组分的添加剂亚油酸三甘酯（ＧＴＬ）．结果发现,较少量ＧＴＬ的加入就显著抑制了聚丙烯的降解,且进一步改善了合金的相形态．在合适的ＧＴＬ与ＤＣＰ用量下,反应共混不但显著改善了ＰＰ／ＡＳ合金的相形态,而且提高了合金的力学性能,初步确立了聚丙烯共混物一步反应共混挤出增溶的方法．     

马来酸酐-苯乙烯熔融接枝聚丙烯的影响因素及其性能研究

用单螺杆挤出机制备了马来酸酐 (MAH) 苯乙烯 (St)对聚丙烯 (PP)的多组分单体自由基熔融接枝体系 .研究证实了当两种单体物质的量比约为 1∶1时 ,接枝物的接枝率最高 ,而熔体流动速率 (MFR)最大 .对反应体系影响因素的研究表明单体用量和引发剂用量对不同单体用量比的系列接枝物的接枝率会产生不同的影响 ;另外 ,单体用量增加 ,接枝物的MFR减小 ,过氧化二异丙苯 (DCP)用量增加 ,接枝物的MFR增加 .对多单体熔融接枝聚丙烯PP g (MAH co St)的力学性能研究发现 ,选用合适的单体用量比、单体用量和DCP用量时 ,所制备的接枝物可具有与纯PP相当或更佳的力学性能     

多组分单体熔融接枝聚丙烯及其性能研究

利用单螺杆挤出机研究聚丙烯的多组分极性单体熔融接枝，从而改善和提高聚丙烯的极性。红外和熔体流动速率的结果表明，对于单组分接枝体系，在适当的反应条件下，甲基丙烯酸缩水甘油酯、甲基丙烯酸羟乙酯等极性单体均可以接枝在聚丙烯上，但同时也伴随着较严重的聚丙烯降解。而采用多组分单体接枝体系，通过加入甲基丙烯酸缩水甘油酯和苯乙烯单体，或甲基丙烯酸羟乙酯和苯乙烯单体，能够有效地控制聚丙烯的降解，大幅度提高接枝率，     

聚丙烯熔融法接枝HEMA的研究

采用熔融接枝法制备了聚丙烯接枝甲基丙烯酸β－羟乙酯考察了反应温度，反应时间，甲基丙烯酸β－羟乙酯及过氧化二异丙苯浓度对甲基丙烯酸β－羟乙酯接枝率的影响，同时，用红外光谱对接枝物进行了定性表征，测定了接枝物的拉伸性能。     

多官能团单体对马来酸酐接枝聚丙烯流变行为的影响

研究了多官能团辅助单体偏苯三酸三丙烯酯(TATM)对马来酸酐接枝聚丙烯的熔体流动速率(MFR)和流变行为的影响.当以不含抗氧剂的聚丙烯粉料为原料时,TATM的加入对稳定接枝产物MFR的效果并不理想.但将聚丙烯粉料添加抗氧剂并造粒后,TATM的加入则可有效稳定体系的MFR,各种流变曲线显示出接枝产物的熔体弹性明显提高,说明有枝化或交联结构出现.针对PP粉料和粒料间接枝产物流变行为存在的重大差异,结合熔体自由基接枝反应的机理进行了解释.TATM能够起到稳定MFR的效果是由于其提高了接枝物的熔体弹性,从而抵消了聚丙烯熔体接枝反应中所不可避免的β断链所造成的剪切黏度下降.聚丙烯粉料和粒料中抗氧剂的差异对聚丙烯的加工降解有严重影响,造成了TATM在不同聚丙烯体系中效果的差异.     

PP/EPDM共混体系的辐射效应

聚丙烯和三元乙丙橡胶(EPDM)的γ辐射效应及辐射后的聚丙烯熔体流动速率的测定表明,在限定空气中聚丙烯随着辐照剂量的增加,熔体流动速率急剧下降,而三元乙丙橡胶随辐射剂量的增加,凝胶含量逐渐增加。在20kGy的剂量辐照下,凝胶含量为22．7％,加入2％的三聚异氰酸三烯丙酯,在相同的剂量辐照下,凝胶含量达到68％。在低剂量下辐照对共混物的拉伸强度影响不大,对冲击强度有很大的影响。在20kGy的剂量辐照下,加入50％EPDM的聚丙烯的缺口冲击强度由1．95kJ／m^2提高到30kJ／m^2,维卡软化温度由85．9℃提高到97．0℃。     

反应挤出条件对PP-g-GMA接枝率、接枝效率和熔体流动速率的影响

聚丙烯;反应挤出条件对PP-g-GMA接枝率、接枝效率和熔体流动速率的影响;甲基丙烯酸环氧丙烷;接枝共聚;共聚     

预辐射聚丙烯反应挤出接枝丙烯酸的研究

利用电子束(EB)预辐照方法和反应挤出技术制备了聚丙烯接枝丙烯酸共聚物PP-g-AA. 采用化学滴定、红外光谱、偏光显微镜(PLM)、DSC和广角X射线衍射(WAXD)对接枝产物进行了表征. 研究结果表明, 接枝率随辐照剂量增加而增大并逐渐达到平台值, 但随单体浓度增大而表现为线性增加, 接枝链能起到异相成核作用, 从而提高了结晶速率并细化了球晶. 同时, 熔体流动速率(MFR)和力学性能测试结果表明, 预辐射和挤出过程造成了PP严重降解, 据此可认为接枝反应主要发生在聚丙烯断裂分子链的末端.     

HIPS／PP熔融反应共混及其动态力学性质

研究了高抗冲聚苯乙烯（HIPS）／聚丙烯（PP）共混物在过氧化二异丙苯（DCP）存在下的熔融反应过程及其动态力学性质．HIPS在DCP存在下以聚苯乙烯（PS）的降解为主，伴随着聚丁二烯（PB）的交联和接枝，PP在DCP存在下以降解为主，HIPS／PP在DCP存在下以PP同HIPS的反应接枝为主，这种原位生成的增容剂显著地改善了HIPS／PP两组份间的相容性，其分子运动特征较前两者发生明显变化，PS的Tg下降，PB和PP的Tg升高．     

影响熔喷料聚丙烯熔体流动速率测试精密度的因素

采用熔体流动速率仪检测熔喷料聚丙烯材料的熔体流动速率,考察了三种不同熔喷料聚丙烯在不同测试条件下的熔体流动速率测试精密度的影响因素,结果标明当仪器恒温预热时间大于30 min、样品加入量8 g、料筒使用氮气吹扫8 s以上、精确控制仪器温度、装料时间控制在50~60 s以内、采用较小活塞位移距离并增加取样次数时,会大大提高测试结果的精密度。     

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性;均苯四甲酸二酐;联苯四羧酸二酐;二羟基联苯胺;聚酰亚胺;聚苯并噁唑;耐热性     

Synthesis of Some Novel Class of Bis(isoxazoline) and Bis(aziridine) Derivatives

Synthesis of some new bis(isoxazoline) derivatives has been described from terepthaldehyde derived bis(nitrones) using microwave irradiation via 1,3‐dipolar cycloaddition reaction. Bis(isoxazoline) derivatives in turn successfully converted into new bis(aziridine) derivatives via Baldwin rearrangement. Simple reaction methodology, non involvement of catalysts, and good to excellent yields are the important features noticed in this synthesis.     

柴油加氢精制催化剂制备技术

柴油加氢精制催化剂制备技术的发展大致经历了3个阶段,由此形成了三代柴油加氢催化剂:单层分散的负载型金属硫化物催化剂,多层分散的负载型金属硫化物催化剂和非负载型金属硫化物催化剂。本文对金属硫化钼基柴油加氢精制催化剂的应用背景、制备思想及催化剂研究开发现状进行了系统的总结,对柴油加氢催化剂的发展方向进行了展望。     

Magnetism of metal-nitroxide compounds involving bis-chelating imidazole and benzimidazole substituted nitronyl nitroxide free radicals

Coordination compounds based on imidazole and benzimidazole substituted nitronyl nitroxide radicals with transition metal ions and trivalent lanthanide ions are described from the perspective of their magnetic properties.For the transition metal compounds the crystal structures show various metal-nitroxide dimensionalities including mononuclear (0D), one-dimensional (1D) and two-dimensional (2D) complexes. The mononuclear complexes were isolated with most metal ions of the first transition series. One copper(II) complex shows a copper(II)-radical ferromagnetic coupling (J = +75 cm⁻¹) while for the other mononuclear compounds, mainly with manganese(II), the metal-radical interactions are antiferromagnetic. The one-dimensional and two-dimensional complexes are manganese(II) compounds which show canting effects leading to weak ferromagnetism.For the trivalent lanthanide ions [La(III), Gd(III) and Eu(III)], three series of mononuclear complexes were obtained in which the metal center is bound to four, two or one nitroxide radicals depending on the counter ions and ancillary ligands. Unexpectedly, in most gadolinium(III) complexes, the Gd(III)-radical interactions were found to be antiferromagnetic in contradiction with other foundings and previous theoretical models. In support to the magnetic studies, the optical properties of the lantanide complexes have also been investigated and are briefly described.     

Transition metal complexes of the tripodal ligand 4-(2′-pyridylmethyl)-4-azaheptane-1,7-diamine. Crystal structures of [CuLCl]ClO4 and [NiL(MeCN)2](ClO4)2

The tripodal ligand 4-(2′-pyridylmthyl)-4-azaheptane-1,7-diamine has been prepared by reaction of 2-aminemethyl pyridine with acrylonitrile, followed by the reduction of the nitrile groups. Copper(II), nickel(II), zinc(II), cobalt(III) and chromium(III) complexes of the ligand have been prepared and characterized and the crystal structures of the complexes [CuLCl]ClO₄ and [NiL(MeCN)₂](ClO₄)₂ determined. The copper complex is five coordinate with approximate square pyramidal stereochemistry with the apical position occupied by a primary amine donor. The nickel complex is octahedral with the pyridine nitrogen donor lying trans to an acetonitrile ligand.     

Simple,Selective, and Sensitive Spectrophotometric Method for Determination of Trace Amounts of Nickel（Ⅱ）, Copper （Ⅱ）, Cobalt （Ⅱ）, and Iron （Ⅲ） with a Novel Reagent 2-Pyridine Carboxaldehyde Isonicotinyl Hydrazone

A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone（2-PYAINH） was synthesized and studied for the spectrophotometric determination of nickel, copper, cobalt, and iron in detail. At a pH value of 7.0, 9,0, 9.0, and 8.0, respectively, which greatly increased the selectivity; nickel, copper, cobalt, and iron reacted with 2-PYAINH to form a 1：2 yellow-orange, 1：2 yellow-green, 1：2 yellow and 1：1 yellow complexes, with absorption peaks at 363, 352, 346, and 359 nm, respectively. Under the optimal conditions, Beer＇s law was obeyed over the ranges of 0.01-1.4, 0.01-1.5, 0.01-2.7, and 0.01-5.4 mg/L respectively. The apparent molar absorptivity and Sandell＇s sensitivities were 8.4×10^4, 5.2×10^4, 7.1×10^4, and 3.9×10^4 L·mol^-l·cm^-1, respectively, and 0.00069, 0.0012, 0.00078, and 0.0014 μg·cm2, respectively. The detection limits were found to be 0.001, 0.002, 0.003, and 0.01 mg/L, respectively. The detailed study of various interfering ions to make the method more sensitive was carried out and selective and several real samples were analyzed with satisfactory results.     

Sample preparation and current applications of liquid chromatography for the determination of non-structural carbohydrates in plants

This article summarizes the current methods of determination of non-structural carbohydrates (NSCs) in plant samples based on liquid chromatography (LC). NSCs comprise several types of carbohydrates: sugar alcohols (e.g., sorbitol), monosaccharides (e.g., glucose and fructose), disaccharides (e.g., sucrose), oligosaccharides (e.g., raffinose) and polysaccharides [e.g., starch and polyfructans (e.g., inulin)]. NSCs are important in plant metabolism and have to be strictly distinguished from all sorts of structural carbohydrates (e.g., polysaccharide cellulose) that make up the backbone of the plants. Consequently, preservation of structural carbohydrates is a crucial step during sample preparation for NSC determination and is therefore addressed.Sugar alcohols, monosaccharides, disaccharides and those oligosaccharides that are easily soluble in polar solvents can be analyzed directly by high-performance LC. They are also referred to as free carbohydrates (FCs).However, polysaccharides are generally submitted to hydrolyzation into monomers prior to their quantitative analysis. This can be done either chemically, using acids, or enzymatically - both methods are discussed. For identification and quantification of the NSCs after LC separation, the following detectors are used: pulsed amperometry, refractive index, evaporate light scattering and finally, mass spectrometry.     

Electrochemically selective determination of dopamine in the presence of ascorbic and uric acids on the surface of the modified Nafion/single wall carbon nanotube/poly(3-methylthiophene) glassy carbon electrodes

A voltammetric method based on a combination of incorporated Nafion, single-walled carbon nanotubes and poly(3-methylthiophene) film-modified glassy carbon electrode (NF/SWCNT/PMT/GCE) has been successfully developed for selective determination of dopamine (DA) in the ternary mixture of dopamine, ascorbic acid (AA) and uric acid (UA) in 0.1M phosphate buffer solution (PBS) pH 4. It was shown that to detect DA from binary DA-AA mixture, the use of NF/PMT/GCE was sufficient, but to detect DA from ternary DA-AA-UA mixture NF/SWCNT/PMT/GCE was required. The later modified electrode exhibits superior electrocatalytic activity towards AA, DA and UA thanks to synergic effect of NF/SWCNT (combining unique properties of SWCNT such as high specific surface area, electrocatalytic and adsorptive properties, with the cation selectivity of NF). On the surface of NF/SWCNT/PMT/GCE AA, DA, UA were oxidized respectively at distinguishable potentials of 0.15, 0.37 and 0.53 V (vs. Ag/AgCl), to form well-defined and sharp peaks, making possible simultaneous determination of each compound. Also, it has several advantages, such as simple preparation method, high sensitivity, low detection limit and excellent reproducibility. Thus, the proposed NF/SWCNT/PMT/GCE could be advantageously employed for the determination of DA in real pharmaceutical formulations.     

The development and application of guidance on equipment qualification of analytical instruments

 This paper describes the development of guidance for the equipment qualification (EQ) of analytical instruments. EQ is a formal process that provides documented evidence that an instrument is fit for its intended purpose and kept in a state of maintenance and calibration consistent with its use.     

Simultaneous determination of mercury and arsenic by anodic stripping voltammetry

An electrochemical method for the simultaneous determinations of Hg^II concentration and total As^III and As^V concentration has been developed. The method does not require the additional preliminary step of the chemical reduction of As^V to As^III, or oxidation of As^III to As^V before stripping analysis takes place. Also, the method for the simultaneous determination of Hg^II concentration and As^III concentration is described. Measurements were performed in 0.1 M HCl using a gold-plated graphite electrode as sensor. Detection limits for both methods are below 0.4 ppb. Relative standard deviation did not exceed 15%. The possible interference by other trace metals was investigated. Analyses of natural water and industrial solutions were made using proposed methods and AAS. The t-test demonstrates that there was no significant difference between the results obtained with these methods. Proposed methods decrease the time of analysis because concentrations of the Hg^II and arsenic ions were measured simultaneously. Also, the removal of the additional step of chemical reduction of As^V to As^III or oxidation of As^III to As^V decreases analysis time, and also reduces the chance of contamination due to the use of additional reagents.