The development and application of guidance on EQ of analytical instruments: High performance liquid chromatography

 This paper describes the development and application of guidance on EQ (EQ) of high performance liquid chromatography instruments. EQ is a formal process that provides documented evidence that an instrument is fit for its intended purpose and kept in a state of maintenance and calibration consistent with its use.     

Simultaneous quantitative determination of the synthetic antioxidant ethoxyquin and its major metabolite in Atlantic salmon (Salmo salar, L), ethoxyquin dimer, by reversed-phase high-performance liquid chromatography with fluorescence detection

A method for simultaneous quantitative determination of ethoxyquin (EQ) and its major metabolite in Atlantic salmon tissues, ethoxyquin dimer (EQ dimer), has been developed. The separation was achieved on tandem coupled phenyl-hexyl and C18 columns by 2-phase gradient elution with acetonitrile-ascorbic acid-acetic acid-diethyl amine organized in a 23.5 min sequence. Compounds were extracted with hexane from samples saponified in ethanol-NaOH and protected from air- and light-mediated oxidation by addition of saturated ethylenediaminetetraacetic acid, ascorbic acid, and pyrogallol. The identity of peaks was confirmed by spiking samples with standards verified by proton nuclear magnetic resonance spectrometry, mass spectrometry, and high-performance liquid chromatography. The detection limit (at 358/433 nm) of matrix-spiked EQ was 0.02 and 0.06 microg/L for EQ dimer, with 0.5 g sample weighed and resuspension in 0.5 mL hexane. Linearity was in the range of 0.2-175 microg/L for EQ and 0.3-5100 microg/L for EQ dimer. Two more ubiquitous compounds were identified as de-ethylated EQ and quinone imine. Totally, 14 peaks sharing spectral properties of EQ were separated in a single run, including a major peak present in all muscle samples, termed unknown metabolite of EQ (UMEQ). The concentrations of EQ, EQ dimer, and de-ethylated EQ, as well as concentrations of UMEQ (in arbitrary units), in the muscle were correlated to the amount of EQ fed to the salmon, thus indicating their possible metabolic origin. The pattern of 14 peaks in the muscle showed high specificity and could be used to discriminate between wild salmon and salmon fed EQ-supplemented feed. This method will be a useful tool for studying EQ metabolism and kinetics, and for the routine surveillance of residual levels of dietary EQ in farmed Atlantic salmon.     

Equipment qualification and its application to conductivity measuring systems

It is only possible to obtain analytical results that are suitable for their intended purpose if the equipment used is capable of producing measurements of the required quality. To ensure that this requirement is met, analysts should define the performance criteria required from the instruments, ensure that only suitable instruments are selected for analytical measurements, and confirm that these instruments continue to meet these criteria for their entire operational life. This process should be conducted on a formal, documented basis, known as equipment qualification. In addition to describing the key elements of equipment qualification for all analytical instruments, this paper gives specific guidance on its application to conductivity systems that has never previously appeared in the literature. The benefits of performing equipment qualification are highlighted and guidance is given on the selection of control standards and why the equipment vendor performing stages of equipment qualification can be of benefit to the user. The relationship between equipment qualification and method validation is discussed, including how these activities play a major role in determining the quality control measures that should be applied to routine analysis.     

Global mapping of equilibrium and transition structures on potential energy surfaces by the scaled hypersphere search method: applications to ab initio surfaces of formaldehyde and propyne molecules

Technical details of a new global mapping technique for finding equilibrium (EQ) and transition structures (TS) on potential energy surfaces (PES), the scaled hypersphere search (SHS) method (Ohno, K.; Maeda, S. Chem. Phys. Lett. 2004, 384, 277), are presented. On the basis of a simple principle that reaction pathways are found as anharmonic downward distortions of PES around an EQ point, the reaction pathways can be obtained as energy minima on the scaled hypersphere surface, which would have a constant energy when the potentials are harmonic. Connections of SHS paths between each EQ are very similar to corresponding intrinsic reaction coordinate (IRC) connections. The energy maximum along the SHS path reaches a region in close proximity to the TS of the reaction pathway, and the subsequent geometry optimization from the SHS maximum structure easily converges to the TS. The SHS method, using the one-after-another algorithm connecting EQ and TS, considerably reduces the multidimensional space to be searched to certain limited regions around the pathways connecting each EQ with the neighboring TS. Applications of the SHS method have been made to ab initio surfaces of formaldehyde and propyne molecules to obtain systematically five EQ and nine TS for formaldehyde and seven EQ and 32 TS for propyne.     

A thermochemistry and kinetic study on the thermal decomposition of ethoxyquinoline and ethoxyisoquinoline

Quantum chemical calculations were used to study the production of ethylene and keto/enol tautomers from ethoxyquinoline (2‐EQ) and ethoxyisoquinoline (1‐EisoQ and 3‐EisoQ) in the gas phase and ethanol at the MP2/6‐311++G(2d,2p)//BMK/6‐31+G(d,p) level. The obtained data indicate that the elimination of ethylene from 1‐EisoQ and 2‐EQ is slightly more favorable than from 3‐EisoQ. Formation of quinolone and isoquinolone (2‐EQO, 1‐EisoQO, and 3‐EisoQO) is kinetically favored compared to their enols. Decomposition of 2‐EQ and 1‐EisoQ to ethylene and keto forms is thermodynamically and kinetically preferable more stable than the corresponding enols. However, the hydroxy form of 3‐EisoQ is more stable than its keto tautomer in the gas phase and ethanol. The enol tautomers cost less energy when formed from their keto forms rather than from the parent ethoxyquinolone and ethoxyisoquinoline.     

Cross-section calculations of proton induced (p,n) and (p,2n) reactions for production of diagnostic 67Ga, 81Rb, 111In, 123,124I, 123Cs and 123Xe radioisotopes

Investigation of pre-equilibrium (PEQ) and equilibrium (EQ) effects on proton induced reactions for production of radioisotopes are very important. Therefore, in this study, we have calculated the PEQ and EQ cross-sections for ⁶⁷Zn(p,n)⁶⁷Ga, ⁶⁸Zn(p,2n)⁶⁷Ga, ⁸²Kr(p,2n)⁸¹Rb, ¹¹¹Cd(p,n)¹¹¹In, ¹¹²Cd(p,2n)¹¹¹In, ¹²³Te(p,n)¹²³I, ¹²⁴Te(p,2n)¹²³I, ¹²⁴Te(p,n)¹²⁴I and ¹²⁴Xe(p,2n)¹²³Cs reactions for production diagnostic radioisotopes. Calculations have been performed by using the hybrid model, geometry dependent hybrid model and full exciton model of PEQ reaction mechanism with 1–40 MeV proton incident energy. We have also investigated the EQ effects on these reactions using the Weisskopf–Ewing model in the same energy range. The excitation functions including the PEQ and EQ effects on these reactions are evaluated by using the ALICE/ASH (2006) and the TALYS 1.4 (2011) codes. Our results have shown that using these codes is suitable for production diagnostic isotopes mentioned above. To obtain excitation functions for producing the diagnostic radioisotopes the PEQ mechanism has been found more dominant than that of the EQ. The results are discussed and compared with the available experimental data.     

On the Structure of Poly-(Ethylene Oxide) When Immersed in Water

It can be shown that poly-(ethylene oxide) in its monomeric form, at molecular weights greater than about 1,000, cannot be soluble in water. Nonetheless, in actual practice poly-(ethylene oxide) is widely used for its hydrophilicity and for its unlimited aqueous solubility. The explanation for this apparent contradiction lies in the fact that poly-(ethylene oxide) molecules form a nonionic surfactant of a novel category, with its hydrophilic and hydrophobic chains attached to each other over their entire length so that its hydrophilic ethylene oxide side is exposed to the water interface while the hydrophobic poly-(ethylene) side remains hidden thanks to the formation of micelles.     

Proton NMR Studies of the Electronic Effect of Substituents at the Azomethine Carbon of N,N′-Bisethylene (Salicylideniminato) Cobalt (II) Complex

The proton paramagnetic shifts of low spin N,N′-ethylenebis(salicylideniminato)cobalt(II) and its derivatives were studied to understand the effect of substituents at the azomethine carbon on the electronic structure of the Schiff-base cobalt complexes. Analysis of the ¹H paramagnetic shifts of H and CH₃ bonded to the azomethine carbon reveals that spin delocalization through a interaction is responsible for the contact contribution to the paramagnetic shift. When the phenyl group is bonded to the azomethine carbon, the plane of the phenyl group is perpendicular to the plane of the complex and the phenyl group makes a negligible contact contribution to the paramagnetic shift.     

Hidden in plain sight: unlocking the full potential of cyclic voltammetry with the thin-film rotating (ring) disk electrode studies for the investigation of oxygen reduction reaction electrocatalysts

Cyclic voltammetry conducted with a thin-film rotating disk electrode, or ring-disk electrode (CV-TF-R(R)DE) is a very popular ‘ex situ’ tool for the rapid screening of electrocatalysts for their activity in oxygen reduction reaction. Despite its popularity and broad use, in most instances only a small part of the information that could be accessed by CV-TF-R(R)DE is actually used by scientists in their research. This work outlines both innovative and more traditional (but half-forgotten) ways of using CV-TF-R(R)DE to its optimal or full potential in the ongoing quest to study the most relevant features of oxygen reduction reaction electrocatalysts and quickly identify the most promising candidates for their applications in fuel cells or other electrochemical devices.     

Neuroprotective Ability of Apocynin Loaded Nanoparticles (APO-NPs) as NADPH Oxidase (NOX)-Mediated ROS Modulator for Hydrogen Peroxide-Induced Oxidative Neuronal Injuries

Apocynin (APO) is a known multi-enzymatic complexed compound, employed as a viable NADPH oxidase (NOX) inhibitor, extensively used in both traditional and modern-day therapeutic strategies to combat neuronal disorders. However, its therapeutic efficacy is limited by lower solubility and lesser bioavailability; thus, a suitable nanocarrier system to overcome such limitations is needed. The present study is designed to fabricate APO-loaded polymeric nanoparticles (APO-NPs) to enhance its therapeutic efficacy and sustainability in the biological system. The optimized APO NPs in the study exhibited 103.6 ± 6.8 nm and −13.7 ± 0.43 mV of particle size and zeta potential, respectively, along with further confirmation by TEM. In addition, the antioxidant (AO) abilities quantified by DPPH and nitric oxide scavenging assays exhibited comparatively higher AO potential of APO-NPs than APO alone. An in-vitro release profile displayed a linear diffusion pattern of zero order kinetics for APO from the NPs, followed by its cytotoxicity evaluation on the PC12 cell line, which revealed minimal toxicity with higher cell viability, even after treatment with a stress inducer (H₂O₂). The stability of APO-NPs after six months showed minimal AO decline in comparison to APO only, indicating that the designed nano-formulation enhanced therapeutic efficacy for modulating NOX-mediated ROS generation.     

Combining of intelligent models through committee machine for estimation of wax deposition

Deposition of the wax is one of the thorny issues in the petroleum industry, invoking costly problems during the transportation and production of crude oil. Owing to its devastating impacts on oil companies' economy, it is essential to develop a simple and robust strategy for the quantitative estimation of wax deposition. In this paper, support vector regression (SVR) is first proposed to estimate the amount of wax deposition. Subsequently, an artificial neural network (ANN) is developed for wax deposition prediction. Eventually, a sophisticated committee machine (CM) is constructed for combining the results of the SVR and ANN models. Optimal contribution of each model in final prediction of the wax deposit is determined through genetic algorithm in CM. Statistical error analysis shows that the CM model performs better than the individual models performing alone.     

Simultaneous separation of mercury and lignosulfonate from aqueous solution using supported liquid membrane

This paper presents an experimental investigation on facilitated and simultaneous transport of mercury and lignosulfonate (LS) through a flat sheet supported liquid membrane (SLM) having Nylon 6,6 as support, trioctylamine (TOA) as carrier and dichloroethane as solvent. The experiments were performed at various operating conditions such as strip phase concentration, feed pH, carrier concentration and feed concentration to find the best set of parameters that would yield the maximum separation of pure mercury as well as its mixture with LS. The experiments were performed in co-transport mode using NaOH as the strip phase. It was observed that extraction of mercury as well as its mixture increases with increase in concentration of NaOH up to a certain limit 0.1 M NaOH in case of pure solution and 0.2 M NaOH in case of mixture). Feed phase pH significantly affects the mercury separation process. However, initial feed concentration does not affect the extraction process appreciably. Separation of mixture of mercury and LS behaves in a similar way as their pure solution; however the extraction is low in comparison to pure solution. The extraction of mercury from its pure solution is about 81% in 1 h. The extraction of mercury and LS from their mixture is about 52.6% and 50.2%, respectively at optimum condition and in a period of 2 h.     

Modified interdigitated arrays by novel poly(1,8-diaminonaphthalene)/carbon nanotubes composite for selective detection of mercury(II)

This study describes a novel type of interdigitated arrays (IDA), microfabricated by electropolymerizing structured Poly(1,8-diaminonaphthalene)/functionalized multi-walled carbon nanotubes (PDAN/CNT) thin film onto a silicon chip for square wave voltammetry (SWV) multi-element heavy metal ion detection. The structure of PDAN/CNT was characterized by Raman, FE-SEM and AFM techniques. Analysed experiments reveal that the uptake of Hg²⁺ by PDAN/CNT is quite specific and it can be used advantageously for electrochemical sensing of Hg²⁺ thanks to original feature of (Hg²⁺/Hg₂²⁺) redox potential with the respect to that of PDAN/CNT. As-developed IDA type electrode can extend its utility in other sensing applications.     

Theoretical studies on the structural rearrangement of ligand binding pocket in human vitamin D receptor

The structural rearrangement of the ligand binding domain (LBD) of human Vitamin D receptor (hVDR) complexed with 1α, 25‐dihydroxyvitamin D₃ (natural ligand) and its analogues (denoted as b and c ) was studied by molecular dynamics (MD) simulations. MD simulations revealed that these ligands could induce different structural changes of LBD, in which 1α, 25‐dihydroxyvitamin D₃ only led to a minute change, suggesting that LBD adopted its canonical active conformation upon binding the natural ligand, while b and c could provoke a clear structural rearrangement of the LBD. In complex of hVDR‐LBD/ b , it is found that helix 6 (H6) and subsequent loop 6‐7 shift outward and the last turn of H11 shifts away from H12, which generate a new cavity at the bottom of binding pocket to accommodate the extra butyl group on the side chain of ligand b . As for hVDR‐LBD/ c , the steric exclusion of the second side chain of ligand c makes the N‐terminal of H7 move outsides and C‐terminal of H11 close to H12, expanding the bottom of the pocket. These calculation results agree well the experimental observations. © 2010 Wiley Periodicals, Inc. Int J Quantum Chem, 2011     

Thermal,mechanical and electroactive shape memory properties of polyurethane (PU)/poly (lactic acid) (PLA)/CNT nanocomposites

Polymer blend nanocomposites based on thermoplastic polyurethane (PU) elastomer, polylactide (PLA) and surface modified carbon nanotubes were prepared via simple melt mixing process and investigated for its mechanical, dynamic mechanical and electroactive shape memory properties. Chemical and structural characterization of the polymer blend nanocomposites were investigated by Fourier Transform infrared (FT-IR) and wide angle X-ray diffraction (WAXD). Loading of the surface modified carbon nanotube in the PU/PLA polymer blends resulted in the significant improvement on the mechanical properties such as tensile strength, when compared to the pure and pristine CNT loaded polymer blends. Dynamic mechanical analysis showed that the glass transition temperature (T_g) of the PU/PLA blend slightly increases on loading of pristine CNT and this effect is more pronounced on loading surface modified CNTs. Thermal and electrical properties of the polymer blend composites increases significantly on loading pristine or surface modified CNTs. Finally, shape memory studies of the PU/PLA/modified CNT composites exhibit a remarkable recoverability of its shape at lower applied dc voltages, when compared to pure or pristine CNT loaded system.     

Dess-martin periodinane: The reactivity of a λ5-iodane catalyst explained by topological analysis

Dess-Martin periodinane (DMP) and its derivatives are popular organic catalysts. DMP is extremely reactive in the presence of alcohols, catalyzing their oxidative conversion into ketones. However, despite their widespread use, this reactivity has not yet been explained. In the present work, a quantum chemical topological approach is taken to study the electronic structure of DMP. Topological analysis revealed two of the Iodine interpuncts ligand interactions to be notably weaker than the two others. Combined with study of the domain-averaged Fermi hole (DAFH), it was confirmed that the iodine center is λ⁵-hypervalent, forming two 3-center-4-electron and two 3-center-2-electrons bonds. The weakness of these multicenter bonds is ascribed to the high reactivity displayed by DMP. The ability to tune the ligand-iodine interactions is investigated by altering the electronic structure of the ligands. It is demonstrated that DAFH analysis offers powerful insight into the understanding of molecular reactivity.     

高效液相色谱-串联质谱法测定蔬菜水果中双甲脒及其代谢产物

建立了高效液相色谱-串联质谱（HPLC-MS/MS）检测蔬菜水果中双甲脒（AMZ）及其降解或代谢产物单甲脒（DMPF）、2，4-二甲基苯基甲酰胺（DMF）和2，4-二甲基苯胺（DMA）的分析方法。样品经0.1 mol/L NaOH溶液稀释、正己烷-异丙醇（2：1，v/v）混合提取液提取，然后采用HPLC-MS/MS对目标物进行定性确证和定量分析。采用Phenomenex Kinetex C18色谱柱（100 mm×4.6 mm，2.6 μm）分离，以0.1%（v/v）甲酸水溶液和甲醇为流动相进行梯度洗脱，采用电喷雾电离（ESI）源、正离子监测模式进行检测。在1.0~200.0 μg/L范围内，4种目标化合物呈良好的线性关系，相关系数（r）大于0.99；方法的定量限为0.01~0.4 μg/kg。4种目标化合物在0.5、5.0和20.0 μg/kg 3个水平下的加标回收率为62.5%~105.0%，RSD为7.5%~17.6%。该法简便快捷，准确可靠，灵敏度高，定量限满足目前国内外残留限量要求。     

Modification of a Pt surface by spontaneous Sn deposition for electrocatalytic applications. 2. Oxidation of CO,formaldehyde, formic acid,and methanol

The electrocatalytic activity of a spontaneously tin-modified Pt catalyst, fabricated through a simple dip-coating method under open-circuit conditions and characterized using surface analysis methods, was studied in electrooxidation reactions of a preadsorbed CO monolayer and continuous oxidation of methanol, formic acid, and formaldehyde in the potentiodynamic and potentiostatic modes. The catalytic activity of the tin-modified Pt surface is compared with that of a polycrystalline Pt electrode. Spontaneously Sn-modified Pt catalyst shows a superior activity toward adsorbed CO oxidation and thus can be promising for PEFC applications. The methanol oxidation rate is not enhanced on the Sn-modified Pt surface, compared to the Pt electrode. Formic acid oxidation is enhanced in the low potential region on the Sn-modified surface, compared to the Pt electrode. The formaldehyde oxidation rate is dramatically increased by modifying tin species at the most negative potentials, where anodic formaldehyde oxidation is completely suppressed on the pure Pt electrode. The results are discussed in terms of poisoning CO intermediate formation resulting from dehydrogenation of organic molecules on Pt sites, and oxidation of poisoning adsorbed CO species via the surface reaction with OH adsorbed on neighboring Sn sites.     

MR Study of Water Distribution in a Beech (Fagus sylvatica) Branch Using Relaxometry Methods

Wood is a widely used material because it is environmentally sustainable, renewable and relatively inexpensive. Due to the hygroscopic nature of wood, its physical and mechanical properties as well as the susceptibility to fungal decay are strongly influenced by its moisture content, constantly changing in the course of everyday use. Therefore, the understanding of the water state (free or bound) and its distribution at different moisture contents is of great importance. In this study, changes of the water state and its distribution in a beech sample while drying from the green (fresh cut) to the absolutely dry state were monitored by 1D and 2D ¹H NMR relaxometry as well as by spatial mapping of the relaxation times T₁ and T₂. The relaxometry results are consistent with the model of homogeneously emptying pores in the bioporous system with connected pores. This was also confirmed by the relaxation time mapping results which revealed the moisture transport in the course of drying from an axially oriented early- and latewood system to radial rays through which it evaporates from the branch. The results of this study confirmed that MRI is an efficient tool to study the pathways of water transport in wood in the course of drying and is capable of determining the state of water and its distribution in wood.     

A pH-stat study of the reaction of some transition metal cations with disodium ethylenedinitrilotetraacetate (EDTA) and its analytical application

The pH-stat titration technique is an autonomous and very powerful tool for performing and monitoring chelatometric titrations of metal cations with great accuracy, poorly known, however, and seldom exploited. Based on measurement of the amount of strong base required to keep the pH of the test solution at a selected value during stepwise known additions of ethylenedinitrilotetraacetate (EDTA), it requires a glass electrode as the only sensor and is easily implemented on potentiometric titrators. It was introduced a quarter of century ago on an empirical basis for a very peculiar purpose (determination of calcium in diary products), but only very recently it was generalised and its fundamentals were thoroughly examined. In this work, pH-static titrations of some transition metal cations of analytical relevance (Co²⁺, Cu²⁺, Mn²⁺, Zn²⁺) were thoroughly investigated in the acid pH range between 2.3 and 5 or 7 (the highest pH depending on the metal hydroxide or carbonate solubility). The results at higher acidity showed unsuspected properties of such chelation reactions. At moderately acid pH (generally ≥4), indeed, pH-static titrations yield results of high precision and accuracy. On decreasing pH, however, the reaction stoichiomety deviates more and more from the 1:1 ratio between chelating agent and cation, seemingly because of formation of binuclear complexes, an occurrence very seldom mentioned in the current literature. The optimal titration conditions for each metal are defined, and directions for establishing a laboratory protocol for quantitative determinations are given.