碳载体的预处理对Pt/C催化剂结构和性能的影响

采用一种新的调变多元醇制备方法,通过调节碳载体热处理条件,制备得到不同的Pt/C燃料电池催化剂。采用pH计及物理吸附仪表征碳黑表面的含氧官能团和比表面积,利用电感耦合等离子光谱、X射线衍射、透射电镜和循环伏安法分别表征催化剂的成分、物相组成、微观组织形貌和电化学性能,并与进口的Johnson Matthey(JM) Pt/C催化剂的性能进行对比。结果表明:采用调变多元醇法,以400 ℃热处理碳黑作载体所制备的Pt/C催化剂的电化学比表面积达到83 m²·g^-1,质量电流密度为49.03 A·g^-1。而进口催化剂JM 20% Pt/C的电化学比表面积为77 m²·g^-1,质量电流密度仅11.13 A·g^-1,自制催化剂即使Pt载量降低3wt%~4wt%,其电催化活性仍优于进口催化剂。     

新型钴-聚吡咯-碳载Pt燃料电池催化剂的制备与表征

采用脉冲微波辅助化学还原法制备了钴-聚吡咯-碳(Co-PPy-C)载Pt催化剂(Pt/Co-PPy-C),其中Pt的总质量占20%.利用透射电镜(TEM)、光电子射线能谱分析(XPS)和X射线衍射(XRD)研究了催化剂的结构,用循环伏安(CV)、线性扫描伏安(LSV)等方法考察了其电化学活性及氧还原反应(ORR)动力学特性及耐久性.Pt/Co-PPy-C电催化剂的金属颗粒直径约1.8 nm,略小于商用催化剂Pt/C(JM)颗粒尺寸(约2.5 nm);催化剂在载体上分散均匀,粒径分布范围较窄.Pt/Co-PPy-C的电化学活性比表面积(ECSA)(75.1 m2·g-1)高于商用催化剂的ECSA(51.3 m2·g-1).XPS测试表明,自制催化剂表面的Pt主要以零价形式存在.而XRD结果显示,自制催化剂中Pt(111)峰最强,Pt主要为面心立方晶格.Pt/Co-PPy-C具有与Pt/C(JM)相同的半波电位;在0.9 V下,Pt/Co-PPy-C的比活性(1.21 mA·cm-2)高于商用催化剂的比活性(1.04 mA·cm-2),表现出更好的ORR催化活性.动力学性能测试表明催化剂的ORR反应以四电子路线进行.CV测试1000圈后,Pt/Co-PPy-C和Pt/C(JM)的ECSA分别衰减了13.0%和24.0%,可见自制催化剂的耐久性高于商用Pt/C(JM),在质子交换膜燃料电池(PEMFC)领域有一定的应用前景.     

石墨纳米纤维用作质子交换膜燃料电池催化剂载体

利用质子交换膜燃料电池用过的废旧碳纸,采用球磨法制备了石墨纳米纤维(GNF,BET比表面积为229·3m2/g),并以GNF作为载体制备了Pt/GNF催化剂(电化学比表面积为98m2/g).与传统的以VulcanXC-72碳黑为载体的Pt/XC-72催化剂相比,其电化学比表面积及Pt粒径大小相近.采用恒电位氧化法考察了GNF,XC-72,Pt/GNF和Pt/XC-72的电化学稳定性.结果表明,在相同条件下,XC-72的峰电流增加了60%,而GNF增加了2%;Pt/XC-72的腐蚀电流比Pt/GNF的大40%;恒电位氧化60h后,Pt/XC-72约有84·7%的电化学比表面积损失,Pt/GNF仅损失37·2%.这表明GNF的抗腐蚀性优于XC-72,有希望成为质子交换膜燃料电池抗腐蚀的催化剂载体.     

酸处理石墨化碳载体对燃料电池催化剂性能的影响

通过1700 ℃高温处理XC-72CB得到石墨化碳黑(GCB), 并采用酸处理对GCB碳载体进行官能团修饰. 透射电子显微镜(TEM)、 X射线粉末衍射(XRD)和拉曼光谱的结果显示, 酸处理后GCB的石墨化程度增加; N₂吸附-脱附结果证明GCB比表面积减小, 微孔数量减少; 热重分析结果表明, GCB热稳定性增强; 红外光谱和拉曼光谱结果显示, GCB表面引入了含氧官能团, 并同时保持了GCB的有序化结构. 采用循环伏安(CV)法和线性扫描伏安(LSV)法测试了不同预处理后催化剂的电化学性能, 表明其电化学活性表面积(ECSA, 75.25 m²/g)和质量比活性(MA, 0.093 A/mg)均高于商业Pt/C(JM)催化剂. TEM结果表明, 使用经过浓硫酸和浓硝酸混合酸处理的GCB(简称OGCB)作为载体得到的Pt/OGCB平均粒径为2.28 nm, 略小于商业Pt/C(JM)催化剂(约2.5 nm); 经5000周电化学循环伏安测试后, Pt/OGCB的电化学活性表面积衰减17.3%, 质量比活性衰减29.5%, 而Pt/C(JM)的ECSA衰减达到25.1%, MA衰减达到42.5%.     

不同方法制备Pt/C催化剂对燃料电池催化活性的影响

分别采用高压有机溶剂法和回流法不同的制备方法,制备了含铂20%(w)的催化剂Pt/C-HP(高压有机溶剂法)和Pt/C-Reflux(回流法)。实验发现:对于甲醇的阳极氧化过程,高压有机溶胶法制得的催化剂活性较高,催化剂Pt/C-HP甲醇氧化峰电流密度是Pt/C-Reflux的1.5倍,且远远高于商业催化剂JM3000含铂20%(w)Pt/C催化剂,催化剂Pt/C-Reflux甲醇氧化峰电流密度与商业催化剂JM3000催化剂相当。采用X射线衍射(XRD)、透射电镜(TEM)、循环伏安法(CV)等方法对催化剂进行表征的结果表明:高压有机溶胶法制得的催化剂分散性比回流法制得的催化剂好,使得前者催化剂的电化学活性比表面积得到了显著的提高。     

扫帚状氧化铈制备及其对Pt基阳极催化剂催化性能的影响

采用水热合成法,合成了比表面积为175 m~2·g~(-1),孔径在2~4nm范围内的扫帚状CeO_2。通过微波辅助乙二醇还原氯铂酸法制备了Pt-CeO_2/RGO催化剂,探究扫帚状CeO_2的添加对Pt基催化剂电催化性能的影响。利用X射线衍射仪(XRD)、扫描电镜(SEM)、N_2吸附-脱附、X射线光电子能谱(XPS)对所制备的CeO_2及催化剂进行表征。利用电化学工作站对催化剂进行电化学性能测试。结果表明,催化剂中CeO_2保持原有扫帚状,Pt纳米粒子均匀分布于石墨烯载体表面;当m_(RGO)∶m_(CeO2)=1∶2时,添加了扫帚状CeO_2的Pt-CeO_2/RGO催化剂的电催化性能最优,电化学活性表面积为102.83 m~2·g~(-1),对乙醇氧化的峰值电流密度为757.17A·g~(-1),1 000 s的稳态电流密度为108.17 A·g~(-1),对乙醇催化氧化反应的电荷转移电阻最小,活化能最低。     

热处理温度对沥青基硼氮共掺杂多孔炭结构与电化学性能的影响

以煤液化沥青质为碳源、硝酸为氮源、硼酸为硼源和造孔剂制备硼氮共掺杂多孔炭,研究了热处理温度对其孔结构和表面性质的影响,测试了产品作为超级电容器电极材料的性能.用X射线衍射(XRD)、拉曼光谱、扫描电镜(SEM)、透射电镜(TEM)、N2吸附、元素分析、电感耦合等离子体发射光谱(ICP-AES)、X射线光电子能谱(XPS)、电化学工作站等对材料的结构、组成及电化学性能进行了表征.结果表明:随着热处理温度的升高,产品的石墨化程度逐渐升高;比表面积、总孔容呈先增加后减小的趋势;氮含量随着热处理温度的升高逐渐降低,而硼含量则随着热处理温度的升高逐渐增加;材料的比电容随着热处理温度的升高先逐渐增加后减小.其中900°C热处理的样品比表面积达到1103 m2·g-1,总孔容为0.921 cm3·g-1,氮含量为5.256%(w),硼含量为1.703%(w),在6 mol·L-1KOH电解液中当电流密度为100 mA·g-1时质量比电容为349 F·g-1;而经过1000°C热处理的样品表现出最好的倍率特性,电流密度从100 mA·g-1增加到10A·g-1时比电容保持率为75%.     

惰性盐辅助合成介孔石墨化碳片及其电容性能

以惰性盐KCl为模板、硝酸镍为金属催化剂镍源、葡萄糖为碳源,通过碳化处理制备了介孔石墨化碳片。利用扫描电子显微镜、透射电子显微镜、X-射线衍射仪和比表面测试仪对介孔石墨化碳片进行了表征。探讨了碳片形成的机理,采用三电极测试体系研究了介孔石墨化碳片电极材料的电化学性能。结果表明,10 g KCl制备的碳片比表面积最大(989 m2·g-1),在6 mol·L-1KOH电解液中,当电流密度为0.5 A·g-1时,比电容达到180 F·g-1;当电流密度达到10 A·g-1时,比电容维持在148 F·g-1,显示了电极具有较好的倍率性能;在10 A·g-1条件下,2 000次循环充放电测试后电容没有发生衰减,展示了在超级电容器方面的应用潜力。     

高分散直接甲醇燃料电池Pt／C阴极电催化剂的制备过程机理与表征

 通过调变的多元醇法制备了40％Pt／C直接甲醇燃料电池阴极电催化剂，应用透射电镜（TEM）及X射线衍射（XRD）方法表征催化剂．结果表明，由该制备方法可得到高分散，金属粒子粒径分布窄的高载量贵金属催化剂．TEM统计结果表明，调变多元醇法制备的40％Pt／C催化剂的金属粒子平均粒径约为2．9nm．直接甲醇燃料电池单池性能测试表明，该方法制得的40％Pt／C的电催化氧还原能力比同型商品催化剂更好．另外，利用UV－Vis光谱研究了催化剂的制备过程．结果表明，在调变的多元醇法中，Pt4＋的还原是一步完成的．     

无模板剂合成用于超级电容器的二氧化锰/石墨烯复合材料(英文)

以尿素、四水合氯化锰和氧化石墨烯为原料,采用水热法并通过热分解制备了一种具有石墨烯包覆结构的石墨烯-二氧化锰复合材料,利用扫描电子显微镜、X射线衍射、比表面积(BET)、拉曼光谱和热失重等技术对其形貌、晶体结构及表面结构进行了表征;在三电极条件下利用循环伏安法、恒流充放电法和交流阻抗法测试了材料的电化学性能,并考察了不同石墨烯含量对材料比电容的影响.结果表明,在不添加模板剂的条件下制备的复合材料中二氧化锰是具有介孔结构的α-MnO2,当复合15%(质量分数)的石墨烯后材料的比表面积从109 m2·g-1提高到168 m2·g-1.复合材料具有更好的电化学性能,在0.2 A·g-1电流密度下复合材料的比电容达到最大值(454 F·g-1),远高于纯二氧化锰的值(294 F·g-1).在2 A·g-1的电流密度下恒流充放电2000次后复合材料的比电容保持率为92%.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。