基于Ni_(12)P_5纳米粒子的电化学传感器用于灵敏测定葡萄糖（英文）

通过改进的热溶剂胶体合成法制备了单分散的Ni_(12)P_5纳米粒子,并利用X射线衍射、透射电子显微镜、X射线光电子能谱、X射线能谱对Ni_(12)P_5纳米粒子的晶体结构、化学组成和形貌等进行了表征。基于单分散Ni_(12)P_5纳米粒子研制出的非酶葡萄糖传感器具有出色的性能,其快速响应时间小于3 s,检测范围广(0.002～4.2 mmol·L-1),灵敏度高达1 572 mA·L·mol~(-1)·cm~(-2),检测限低至0.8μmol·L~(-1)。此外,该传感器在用于人体血液中葡萄糖的实际检测中取得了满意的效果。     

微波辅助法制备氢氧化镍-石墨烯纳米复合结构及在葡萄糖检测中的应用

采用微波辅助合成法制备了氢氧化镍-石墨烯[Ni(OH)_2-graphene]纳米复合结构,利用扫描电子显微镜(SEM)、X射线光电子能谱(XPS)、电子能谱(EDS)、X射线衍射(XRD)及电化学阻抗谱(EIS)对其结构和性质进行了表征.电化学实验结果表明,与单独的Ni(OH)_2相比,Ni(OH)_2-graphene纳米复合结构对葡萄糖氧化反应表现出更高的电催化活性;同时,据此构建的无酶葡萄糖传感器具有良好的性能,检测线性范围为10μmol/L~7.5 mmol/L,灵敏度为174.7μA·cm~(-2)·mmol·L~(-1),检出限为2.0μmol/L(S/N=3),且该传感器具有良好的稳定性和选择性,可用于实际样品检测.     

氮掺杂介孔碳的制备及其电化学超电容性能（英文）

通过直接炭化沸石咪唑酯骨架结构材料(ZIF-8)纳米多面体,成功制备了氮掺杂介孔碳(NMCs).采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)、拉曼光谱、X射线光电子能谱(XPS)及比表面和孔隙度分析仪对其微观形貌和结构进行了表征,并对NMCs的电化学超电容性能进行了测试.结果表明:NMCs具有规整的形貌、介孔纳米结构和较大比表面积(2737 m2·g-1);由于氮元素掺杂所赋予的优异的表面润湿性和赝电容性能,且介孔结构有利于电解质到达电极活性材料表面,NMCs表现出优异的电化学超电容性能,在1A·g-1的电流密度下,1.0 mol·L-1H2SO4溶液中的比电容值为307 F·g-1,并具有良好的功率特性;此外,在10 A·g-1的大电流密度下充放电循环5000次后,NMCs的比电容值保持率为96.9%.     

介孔碳化钨纳米片团簇的制备及其电催化析氢性能

采用阳极氧化法与原位还原碳化法相结合,在电击穿条件下可控制备了具有介孔结构的碳化钨纳米片团簇(WC NFs).通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、N2吸附-脱附测试表征其物相、微观结构和孔径分布.在1 mol·L-1 H2SO4溶液中采用线性扫描伏安法、循环伏安法、计时电流法以...     

Cu/MoS2的熔盐电解法制备及其在碱性条件下析氢反应性能的提高

通过熔盐电解法并掺杂过渡金属Cu制备2种不同纳米结构的Cu/MoS_2。采用涂敷法制备工作电极,通过X射线衍射(XRD)、透射电子显微镜(TEM)、能量散射X射线谱(EDS)、扫描电子显微镜(SEM)、选区电子衍射(SAED)以及各种电化学手段验证了其结构和性能。结果表明,纳米片状Cu/MoS_2在碱性溶液(1 mol·L~(-1)KOH)中表现出优异的析氢催化性能:在电流密度为10 mA·cm~(-2)时过电位为199.6 mV,Tafel斜率为59 mV·dec~(-1),双电层电容为26.1 mF·cm~(-2),等效电荷转移电阻为12.4Ω,具有较为良好的电化学耐久性和稳定性。     

阴极等离子体电解法制备氧化铝纳米颗粒

以金属铝为阴极材料,以3mol·L-1浓度的NH4NO3水溶液为电解液,采用非对称电极阴极等离子体电解方法制备出氧化铝纳米颗粒.采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线能量色散谱(EDX)、X射线衍射(XRD)和X射线光电子能谱(XPS)对颗粒的形貌和结构进行了表征.结果表明颗粒以立方相Al2O3为主.还对放电过程的电流变化和发光现象进行了研究.结合实验结果提出了这种颗粒的生长机制.     

Ce掺杂In_2O_3纳米纤维的制备及其三乙胺气敏性能(英文)

用简单有效的静电纺丝法制备了Ce掺杂的In2O3纳米纤维材料.采用X射线衍射(XRD)、透射电子显微镜(TEM)、高分辨率透射电子显微镜(HRTEM)和扫描电子显微镜(SEM)对合成样品的晶体结构和形貌进行了表征.结果显示,此纤维材料的平均直径约为90nm,长度达到几十个微米.气敏性能测试结果表明,4%(w)Ce掺杂的In2O3纳米纤维对三乙胺的灵敏度最高,该气敏元件对3μL·L-1三乙胺的灵敏度达到2.6,响应时间为5s,恢复时间约为6s,且具有较好的选择性.     

葡萄糖辅助合成碲化铅纳米棒及其表征

采用简单的葡萄糖辅助溶剂热合成法制备了碲化铅纳米棒。 利用X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)、高分辨率透射电子显微镜(HRTEM)、能谱仪(EDS)等技术手段进行材料结构和形貌表征。 结果表明,产物是纯的立方相PbTe,纳米棒的直径约为50 nm,长500 nm左右。 研究了反应过程的影响因素及碲化铅纳米棒的形成机制。 产物的形貌受葡萄糖的量、反应时间、反应温度和聚乙烯吡咯烷酮(PVP)质量的控制,分析了形成这种结构的原因。     

核-壳结构TiO_2@Pt复合纳米颗粒修饰的葡萄糖生物传感器

制备了核-壳结构的TiO2@Pt复合纳米颗粒,并修饰于恒电位沉积的普鲁士蓝-壳聚糖(PB-CS)杂化膜表面,以固定葡萄糖氧化酶。由于TiO2@Pt复合纳米颗粒的引入显著增大了传感器的导电性和酶的固载量,同时CS的掺杂,防止了PB的泄露,使得传感器对葡萄糖具有较好的催化作用。该传感器在1.2×10-6~1.1×10-3mol·L-1范围内,响应电流与葡萄糖浓度呈良好的线性,相关系数(r)为0.998 6,检出限(S/N=3)达到4.0×10-7mol·L-1,灵敏度为13.31 mA·mol·L-1·cm-2。对0.3 mmol·L-1的葡萄糖标准溶液连续检测5次,其相对标准偏差为3.8%。     

水热法制备MoO3-GQDs的三甲胺气敏性能

采用水热法制备了一系列具有不同碳量子点(GQDs)含量的MoO3?GQDs纳米复合材料,利用X射线衍射、扫描电子显微镜、透射电子显微镜、FTIR等对MoO3?GQDs复合材料进行了表征,研究了其气敏性能。结果表明,复合材料中GQDs的含量对MoO3?GQDs复合材料的气敏响应和选择性有显著影响。MoO3?GQDs纳米复合材料(S?6,GQDs悬浮液的含量为6 mL)传感器在230℃时对三甲胺(TMA)表现出高的气敏响应和好的气敏选择性;该传感器对1000μL·L^-1 TMA的响应为74.08;对1000μL·L^-1 TMA的响应时间和恢复时间分别为73和34 s;S?6复合材料气敏传感器在230℃时可以检测到1μL·L^-1的TMA。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.