Li4Ti5O12溶胶-凝胶法合成及其机理研究

The precursors of Li₄Ti₅O₁₂ were prepared from tetrabutyl titanate and lithium acetate by sol-gel process. The Li₄Ti₅O₁₂ samples were synthesized by calcining the gel precursors at 400～900 ℃ in air for 6～20 h. Its reaction mechanism was investigated by infrared spectroscopy(IR), thermogravimetry(TG) and X-ray diffraction(XRD). The effects of sinter-temperature, calcination-time and thermal-treatment for the products were discussed. The samples were characterized by X-ray diffraction(XRD), scanning electron microscopy(SEM). The results showed that the single-phase products were obtained by calcining the gel precursors at 800 ℃ in air for 20 h, the sinter-temperature was lower than that of solid-state method, the particles were narrowly distributed, well crystallized with a size range from 0.3μm to 0.5 μm.     

梯度材料LiNi0.8Co0.2O2的合成与表征

The gradient composite LiNi_0.8Co_0.2O₂ was synthesized using spherical Ni(OH)₂ particle coated by a sol-gel containing cobalt and lithium. The precursor was examined by DSC-TG. The gradient composite was characterized by SEM, EDS, XPS, XRD and ICP-AES. The XPS, EDS and ICP-AES results show that content of cobalt in the surface is higher than in the center of the spherical particle of the gradient composite. The first discharge specific capacity of the gradient composite sintered at 700 ℃ is 187.3 mAh·g^-1.     

洗涤时pH值对纳米级β-Ni(OH)2的团聚程度和电化学性能的影响

Nano-scale nickel hydroxide was prepared by precipitate transformation method in the paper. Effect of rinse pH on the agglomeration degree and electrochemical performance of nano-scale Ni(OH)₂ was investigated. The mea-surement results of XRD and TEM indicate that the prepared nano-scale Ni(OH)₂ is β(Ⅱ)-phase,the grain size is in the rang of 10～50nm,and rinse pH exerts a great influence on the agglomeration degree of nano-scale Ni(OH)₂. The agglomeration of material becomes very obvious when rinse pH=11, and the density of nano-scale Ni(OH)₂ is enhanced obviously.Cyclic voltammetry(CV) and simulate cells experiment show that nano-scale Ni(OH)₂ with suitable agglomeration degree have better electrochemical CV performance than those with ideal disperse Ni(OH)₂ and micron Ni(OH)₂, and its proton diffusion coefficient is also the highest. It can elevate the discharge potential platform and prolongs discharge time, so the utilization ratio of Ni(OH)₂ is raised.     

掺钇锆酸锶-TiO2复合光催化剂的制备及性能研究

SrZrO₃ particles were prepared by a co-precipitation method and Sr(Zr_1-xY_x)O_3-δ -TiO₂ composite particles were then synthesized by Sr(Zr_1-xY_x)O_3-δ and titanium dioxide. The composite particles were characterized by XRD, SEM, FTIR and TG-DTA techniques. The photocatalytic degradation of methylene blue (MB) in aqueous solution was used as a probe reaction to evaluate the photocatalytic activity of the composite particles. The effect of the preparation method for SrZrO₃, doping content of yttrium and TiO₂ amount in the composite particles on the photocatalytic activity of composite particles was also discussed. The results show that the methylene blue solution could be completely degraded by Sr(Zr_1-xY_x)O_3-δ -TiO₂ composite particles under UV-light or visible light irradiation. The photocatalytic activity of composite particles was higher than that of pure TiO₂. The fast recombination of photogenerated electrons and holes were restrained by the heterojunction formed in composite particles. The particle of SrZrO₃ prepared by co-precipitation was small, and the photocatalytic activity of composite particles prepared from this kind of SrZrO₃ was higher than that of particles prepared by solid sintering method. The best doping content of yttrium is 5%. The optimal content of TiO₂ in composite particles is 90wt%, 70wt%, respectively under UV-light and visible light irradiation, the degradation rates of MB are 98.8% and 93.5% , respectively after 50 min irradiation.     

锐钛矿型TiO2水溶胶的低温制备及其表征

Anatase titanium dioxide hydrosol was prepared at low temperature by a simple method. The title material was characterized by TEM, XRD, FTIR and BET, respectively. The photocatalytic activity of the as-prepared TiO₂ was evaluated by the degradation of methyl orange solution under sunlight and the photocatalytic oxidation of acetone in air. The results showed that the titanium dioxide hydrosol was composed of anatase phase with average grain size of about 7 nm, and the crystallinity became more perfect with the increase of temperature. The BET surface areas were more than 220 m²·g^-1 for these samples. It is found that the photocatalytic activity was much better for the higher heat processing temperature. Especially, the photocatalytic activity of the sample with a heat treatment of 110 ℃ was better than that of P25. In addition, TiO₂ hydrosol also possessed good photocatalytic activity under the sunlight illumination.     

碱土金属掺杂纳米TiO2催化剂的制备与光催化活性的评价

The nanometer TiO₂ were prepared by the hydrolyze-gel method and fellowed by doping alkaline-earth metals (Mg, Ca, Sr, Ba). XRD, SEM, diffuse reflection spectra were used to investigate their characteristices. The result indicates that the average particles size of the TiO₂ is about 80 nm and keep uniformity in distributing. The product was mainly anatase in 300～400 ℃ calcinations, the einstein shift of absorption spectrum was observed after doping the alkaline-earth metals. The best mole percentages of Mg, Ca, Sr and Ba are 0.5%, 1.0%, 1.5%, 1.5% respectively. Under the same reaction conditions, it is more effective to the UV-catalyed degradation reaction that the catalysts containing Mg and Ca were calcined at 300 ℃ for 1h or containing Sr and Ba were calcined at 400 ℃ for 1 h. The photocatalystic activity is considerably depondent on pH and the concentration of the oxidant. Using the sunlight to do the degradation experimental, the result also show that the doping catalysts has higher degradation efficiency than that of pure TiO₂.     

在LaNiO3-Pt复合电极上Pb(Zr，Ti)O3铁电薄膜及其成分梯度薄膜的制备和研究

LaNiO₃(LNO) thin films were prepared on Pt(111) / Ti / SiO₂/ Si substrate by metal-organic decomposition (MOD) method. Pb(Zr,Ti)O₃ ferroelectric thin films and their compositionally graded thin films were prepared on LNO / Pt / Ti / SiO₂ /Si substrates by Sol-gel method. The composition depth profile of a typical up-graded film was determined by using a combination of Auger Electron Spectroscopy (ASE) and Ar Ion Etching. The results confirm that the processing method produces graded composition changes. XRD analysis showed that the graded thin films possessed composite structure of tetragonal and rhombohedral. The dielectric constants of Up-graded and Down-graded thin films were higher than that of each thin film unit. The dielectric constants were 277 and 269 at 10 kHz, respectively. The loss tangents were 0.019 and 0.018 at 10 kHz, respectively. The Hysteresis loops showed that the remanent polarizations of graded thin films were higher than that of each thin film unit, but the coercive fields were smaller. The remanent polarizations of Up-graded and Down-graded thin films were 30.06 and 26.96 μC·cm^-2, respectively. The coercive fields were 54.14, 54.23 kV·cm^-1, respectively. The pyroelectric coefficients of Up-graded and Down-graded thin films were 4.62, 2.51×10^-8 C·cm^-2·K^-1 at room temperature, respectively. They were higher than that of each thin film unit.     

锂离子电池正极材料LiMn2O4的合成与晶体结构（英）

Spinel LiMn₂O₄ powders were prepared using two-step synthesis method consisting of solid-state reaction method and citrate modified sol-gel method. The effects of the calcination temperature and the Li/Mn ratio of raw materials were studied on the physicochemical and electrochemical properties of the spinel LiMn₂O₄ powders, such as crystallinity, lattice constant and density. The title compound was characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Polycrystalline LiMn₂O₄ powers calcined at 750 ℃ were found to be composed of very uniformly-sized microcrystal with an average particle size of 300 nm. The improvement in electrochemical properties was mainly attributed to the process of re-grinding by absolute alcohol.     

纳米SrTiO3对高铁酸盐电化学性能影响研究

Two ferrates, K₂FeO₄ and BaFeO₄, had been prepared and characterized by XRD, IR and SEM. The electrochemical tests of the samples were carried out in the voltage range of 0.8～2.0 V and current density of 0.5～3.0 mA·cm^-2. The results indicated that performance of Zn-BaFeO₄ battery was superior to that of Zn-MnO₂ and Zn-K₂FeO₄ batteries. Nanometer SrTiO₃ prepared by Sol-gel methode with different ratio was added to the BaFeO₄ cathode in order to improve the discharge performance. The discharge capacity of the BaFeO₄ cathode was increased from 224 mAh·g^-1 to 246 mAh·g^-1 by addition of 5% nanometer SrTiO₃. The reason of enhancing BaFeO₄ electrochemical performance was discussed.     

LiV3O8的合成及其电化学性能研究

The layered trivanadate, LiV₃O₈, was prepared by sol-gel method with LiOH, V₂O₅ and H₂O₂ as initial reagents. The materials at different heat treatment conditions were characterized by XRD and TG-DTA. Their electrochemical behaviors were studied by galvanostatic charge-discharge and cyclic voltammetry. The results show that LiV₃O₈ prepared by sintering at 300 ℃ for 16 h has higher capacity, and its initial discharge capacity is 333.1 mAh·g^-1, and maintains a discharge capacity of 302.8 mAh·g^-1 after 10 cycles at 0.2 C and the voltage range of 1.8～4.0 V.     

碳包覆LiFePO4的一步固相法制备及高温电化学性能

Carbon coated LiFePO₄ cathode material was synthesized by one-step solid-state reaction and characterized by X-ray diffraction (XRD), field-emission-scanning electron microscope (FESEM). Electrochemical performances of the material as cathode in lithium-ion battery were investigated at medium and elevated temperature (30 and 55 ℃) by galvanostatic charge-discharge and A.C. impedance tests. The results show that carbon coated LiFePO₄ powder exhibits a well-crystallized olivine structure and spherical morphology with an average particle size of about 500 nm. Galvanostatic charge-discharge tests show that the reversible discharge capacity at 1 C and 1.5 C rates was improved from 121 and 105 mAh·g^-1 at 30 ℃ to 136 and 123 mAh·g^-1 at 55℃, respectively, while the enhancement of high temperature on electrochemical performance is less obvious at a rate lower than 0.5 C. Impedance spectra analyses indicate that the cathode material has a remarkably higher lithium-ion diffusivity at 55 ℃ than that at 30 ℃, which improves the electrochemical performance at high temperature.     

预氧化固气法合成LiNiO2的研究

LiNiO₂ was prepared by reaction of stoichiometric amounts of thoroughly-mixed LiOH·H₂O and preoxidation nanometer-scale Ni₃O₂(OH)₄ powders in O₂ at the temperature of 700℃ for 6h. The products were tested by XRD， XPS， SEM and electrochemistry methods. It was shown that product was LiNiO₂ single-phase， and the valence of nickel was +3; the average size of it was 40nm; its initial charge specific capacity is 168mAh·g^-1 and the coulomb efficiency is 90%; the second charge specific capacity is 160mAh·g^-1 and the coulomb efficiency is 96%.     

N 掺杂TiO2光催化剂的制备及其可见光活性研究

A visible-light-active photocatalyst was prepared by calcination of the hydrolysis product of tetrabutyl titanate with ammonia as precipitant. The photocatalyst was characterized by X-ray diffraction (XRD), UV-Vis diffuse reflection spectra (DRS), thermal gravimetric-differential thermal analysis (TG-DTA), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM). The color of the photocatalyst was yellow and could absorb light wavelength under 550 nm as measured by DRS. The catalyst calcined at higher temperature will give lower absorbance for visible light. Structures of the sample were characterized mainly to be anatase by XRD except for the sample calcined at 700 ℃ which gave mixtures of anatase and rutile. TG-DTA results showed that temperature for anatase formation was 415 ℃. XPS results showed that doped-nitrogen was presented in the sample, they are important to show visible-light absorbency. The photocatalytic activities were evaluated using methyl orange and phenol as model pollutants, the results showed that over 90% of phenol could be degraded under visible light using N/TiO₂ as the catalyst after 4 hours reaction. Almost the same activity was found for the TiO₂ photocatalyst calcined at different temperature under sunlight but activities were different when the treatment was under UV light.     

混合溶剂前体法制备纳米CuO粉体及其性能表征

Nano-CuO was prepared by heating nano-Cu₂(OH)₂CO₃ precursors in different calcination temperatures. The precursor was synthesized from water-alcohol mixed solution of Cu(Ac)₂ using mixed solution of NaOH and Na₂CO₃as precipitants. XRD, FT-IR, TEM, TG-DTA and surface area measurement techniques were used to investigate the properties of the CuO powder. The results show that the spherical, well dispersed nano-CuO powder with the average size of 15 nm and higher catalytic activity for H₂O₂ decomposition was obtained at 300 ℃. With the increasing of calcination temperature, crystal of CuO grows up, agglomeration of the powder becomes heavier and catalytic activity decreases. FT-IR patterns revealed that the vibration fine structure of Cu-O bond in nano-CuO powder disappears and main absorption is red-shifted with the average size of nano-CuO reducing.     

电镀烧结法制备Ti/SnO2-Sb2O4电极的研究

The Ti/SnO₂-Sb₂O₄ electrode has been prepared by the electroplate-sinter method. The effect of SbCl₃ adding amount and sintering temperature on its electrode lifetime and oxygen evolution potential were investigated by means of EDX, SEM and XRD analysis. The results indicated that the electrode appeared the best performance when the SbCl₃ adding amounts was 0.2g and the sintering temperature was 550℃. In optimized conditions Ti substrate was entirely covered by SnO₂-Sb₂O₄ and the combinations among them were tight. Due to the use of electroplate method, the electrical conductivity, the oxygen evolution potential and the electrode lifetime were increased, so the elec-tro-catalytic activity and the electrochemical stability of the prepared electrode were found to be superior.     

有机体系中纳米TiO2 / ZrO2修饰电极的制备及电催化活性

The complexes Ti(OCH₂CH₂O)₂ and Zr(OCH₂CH₂O)₂ were directly synthesized by using HOCH₂CH₂OH dissolution in 50 mL flask. The nano-ZrO₂ / TiO₂ powders were prepared by a direct sol-gel synthesis using the above solution and followed by drying at 400 ℃ for 2 h. The complexes were characterized by FTIR and ¹H NMR. XRD and TEM were used to investigate the structure of nano-ZrO₂ / TiO₂. The results show that the complexes containing ^-OCH₂CH₂O^- group could prevent the precursor from agglomeration and sintering during the hydrolysis and calcination process. The ZrO₂ / TiO₂ powders of 20～35 nm was thus obtained in a high purity. The highly active nano-ZrO₂ / TiO₂ modified electrode was prepared by using daubing and calcination. The electro-catalytic activities of this electrode in (COOH)₂ were investigated. The discharge current of nano-ZrO₂ / TiO₂ electrode increased obviously. In preparative electrolysis under optimal conditions, the average yield and current efficiency for HOOC-CHO were 84.7% and 91.6 %, respectively.     

纳米尖晶石LixMn2O4的制备与电化学性能表征

Nano-spinel Li_xMn₂O₄(0.6 ≤x≤ 1.0) was synthesized by two steps of coprecipitation and calcination. The influences of calcination temperature, time and Li/Mn ratio on the crystal structure and the particle size of Li_xMn₂O₄ were investigated. It was shown that the higher the calcination temperature, the more complete the crystal structure, and the larger the particle size. Moreover, the influence of calcination time on the crystal structure was insignificant when it was more than 3h at 700℃. With the increase of x in Li_xMn₂O₄ in the range of 0.6～1.0, the d111 and lattice parameter a increased first and then decreased. The electrochemical properties of nano-spinel LiMn₂O₄ using as cathode material of lithium-ion battery were studied. The low discharge capacity might be due to the irreversible capacity loss brought by the large surface area and lattice vacancies of the nano-spinel.     

γ-Fe2O3纳米粉的低热固相制备及其电磁损耗特性(英)

The Fe(OH)₃ precursor was prepared by solid -state reaction with Fe(NO₃)₃·9H₂O, NaOH and dispersed poly-ethylene glycol at low heating temperature(25 ℃). Synthesis of iron oxide (γ-Fe₂O₃) nanoparticle was achieved by thermal decomposition of Fe(OH)₃·xH₂O precursor. The nanoparticle was characterized by TG-DTA, X-ray diffra-ction, TEM etc. The results showed that the nanoparticle was composed of γ-Fe₂O₃ and was a better absorber for electromagnetic wave within the low frequency band.     

LiMn2O4的湿法合成及锰的光度法测定研究

The LiMn₂O₄ spinel was prepared by wet method using Li₂CO₃， Mn(CH₃COO)₂·4H₂O and CO₂ as raw ma-terials. The products were measured by TG/DTA， XRD， IR. The results Showed that the sample calcined at 800℃ for 10h was well crystallized monophase product. The contents of Mn(Ⅲ) and Mn(Ⅳ) of LiMn₂O₄ spinel were determined simultaneously by spectrophotometric analysis with pyrophosphoric acid.     

纳米MgNb2O6微波介质陶瓷粉体制备及表征

Nano-crystalline MgNb₂O₆ was prepared using Mg(NO₃)₂·6H₂O, Nb₂O₅, HF and citric acid as raw materials by auto-ignition route. The process involves the formation of a viscous gel by thermal dehydration of the citrate-nitrate solution at about 80 ℃. The auto-ignition (at about 200 ℃) of the gel resulted in a high reactivity powder containing intimate blending of MgNbF₇ and NbF₃. The crystalline phase of MgNb₂O₆ could be formed easily at 700 ℃, which is 400 ℃ lower than that of common solid-state reaction process. The nano-crystalline MgNb₂O₆ (～30 nm) powder with good dispersity could be obtained at 850 ℃.