GC-MS法测定白酒中邻苯二甲酸酯残留量

采用正己烷提取白酒中的16种邻苯二甲酸酯类增塑剂,建立了气相色谱-质谱联用法测定白酒中污染物邻苯二甲酸酯类增塑剂残留量的检测方法。该方法对白酒中16种邻苯二甲酸酯化合物的检测限为0.05 mg/kg,方法的检测浓度线性范围为0.5~5.0 mg/L,样品的加标回收率为80.0%~95.0%,测定结果的相对标准偏差为2.1%~7.0%(n=6)。该方法可以满足白酒中污染物邻苯二甲酸酯检测的需要。     

超声提取-气相色谱-质谱法测定塑料包装食品中16种邻苯二甲酸酯类增塑剂

建立超声提取–气相色谱–质谱法同时测定塑料包装食品中16种邻苯二甲酸酯类增塑剂的残留量。以甲醇为萃取溶剂,采用超声萃取法进行样品处理,超声提取时间为30 min,超声提取温度为50℃。16种邻苯二甲酸酯类物质的质量浓度在0.1～50 mg/L范围内与峰面积具有良好的线性关系,线性相关系数均大于0.99,方法检出限为0.05 mg/L。样品的加标回收率为83.4%～97.0%,测定结果的相对标准偏差为1.91%～4.64%(n=6)。该方法简单、灵敏且准确,适用于塑料包装食品中16种邻苯二甲酸酯类增塑剂残留量的测定。     

真空离心浓缩/气相色谱-质谱联用法测定白酒中6种邻苯二甲酸酯类增塑剂

建立了测定白酒中6种邻苯二甲酸酯类增塑剂的真空离心浓缩/气相色谱-质谱联用(GC-MS)分析方法。样品经真空离心浓缩,正己烷提取,取上层正己烷,4000r/min离心5min,采用GC-MS测定,外标法定量。在0.10～5.00μg/mL范围内,相关系数r20.992,样品在0.10～2.00 mg/kg范围内加标,平均回收率在88.83%～111.67%之间,相对标准偏差(RSD)为4.85%～11.35%,检出限(LOD)在0.02～0.05 mg/kg之间。采用该方法对16个白酒样品进行测定,结果表明该法简便、快速、结果准确可靠、灵敏度高,能够满足白酒中6种邻苯二甲酸酯增塑剂检测需求。     

高效液相色谱法测定建筑用胶中苯系物和邻苯二甲酸酯类增塑剂

采用高效液相色谱法同时测定建筑用胶中苯系物和邻苯二甲酸酯类增塑剂。样品以乙酸乙酯为萃取剂超声提取,采用C18柱为固定相,乙腈、水为流动相进行梯度洗脱,采用二极管阵列检测器,在254 nm处测定。5种苯系物和5种邻苯二甲酸酯类增塑剂的峰面积与其质量浓度呈线性关系,线性范围在1~3个数量级之间,对苯系物的检出限(3S/N)在0.003~0.006 g.L-1之间,对邻苯二甲酸酯类增塑剂的检出限(3S/N)在0.003 g.L-1之内。对水基型和溶剂型建筑用胶中各物质的回收率在98.1%~101.9%之间。5个实验室间对相同建筑用胶样品中不同目标物测定的相对标准偏差(n=6)在0.8%~4.2%之间。     

真空离心浓缩/气相色谱-质谱联用法测定白酒中6种邻苯二甲酸酯类增塑剂

建立了测定白酒中6种邻苯二甲酸酯类增塑剂的真空离心浓缩/气相色谱-质谱联用(GC-MS)分析方法。样品经真空离心浓缩,正己烷提取,取上层正己烷,4000r/min离心5min,采用GC-MS测定,外标法定量。在0.10～5.00μg/mL范围内,相关系数r2>0.992,样品在0.10～2.00 mg/kg范围内加标,平均回收率在88.83%～111.67%之间,相对标准偏差(RSD)为4.85%～11.35%,检出限(LOD)在0.02～0.05 mg/kg之间。采用该方法对16个白酒样品进行测定,结果表明该法简便、快速、结果准确可靠、灵敏度高,能够满足白酒中6种邻苯二甲酸酯增塑剂检测需求。     

超临界流体色谱同时测定运动饮料中的8种邻苯二甲酸酯类增塑剂

建立了同时快速测定运动饮料中邻苯二甲酸二甲酯、邻苯二甲酸二乙酯、邻苯二甲酸二丙酯、邻苯二甲酸二丁酯、邻苯二甲酸二戊酯、邻苯二甲酸丁基苄基酯、邻苯二甲酸二（2-乙基己基）酯、邻苯二甲酸二辛酯8种邻苯二甲酸酯（PAEs）类增塑剂的超临界流体色谱-紫外检测分析方法。实际样品经液相萃取后,用超临界流体色谱分析,以超临界态二氧化碳-3%（体积分数）甲醇作为色谱流动相进行等度洗脱,检测波长为225 nm,6 min即可实现分离。8种PAE类增塑剂在0.05~25 mg/L范围内均具有良好的线性关系,相关系数为0.9991~0.9997,方法检出限为7.5~15 μg/L。8种PAE类增塑剂在运动饮料样品中的加标回收率为91.7%~100.2%,相对标准偏差均不大于6.5%（n=3）。应用该方法对多种市售运动饮料中的8种PAE类增塑剂进行检测,结果表明,该方法环保、快速、灵敏、选择性高、结果准确,能满足运动饮料中增塑剂含量检测的要求。     

仿真饰品中邻苯二甲酸酯类增塑剂的含量测定和迁移风险考察

建立了仿真饰品中14种邻苯二甲酸酯类增塑剂的含量和迁移量测定的气相色谱-质谱(GC-MS)检测方法。考察了微波萃取、超声波萃取、快速溶剂萃取和索氏提取4种前处理方法对增塑剂含量测定的影响。在模拟人体温度及汗液环境下,考察了0～168 h内塑料仿真饰品中邻苯二甲酸二丁酯(DBP)、邻苯二甲酸二(2-乙基己基)酯(DEHP)和邻苯二甲酸二辛酯(DOP)3种增塑剂的迁移风险。结果表明微波萃取法的提取效率优于其余3种方法。所建立方法的定量限为5 mg/kg (邻苯二甲酸二异壬酯(DINP)、邻苯二甲酸二异癸酯(DIDP)为25 mg/kg),在0.1～50 mg/L(DINP、DIDP在0.5～250 mg/L)范围内,线性相关系数在0.99以上,在3个添加水平下的回收率在90.95%与98.67%之间。在模拟条件下,DEHP的迁移风险较高,浸泡72 h后约有0.75%溶出,而DBP和DOP的溶出风险较低。该法的灵敏度高、回收率高、选择性好,能满足实际工作的要求。     

超声萃取/气相色谱-串联质谱法同时测定皮革制品中20种邻苯二甲酸酯类增塑剂

建立了同时测定皮革制品中20种邻苯二甲酸酯类增塑剂的气相色谱-串联质谱方法。该方法以正己烷为提取溶剂,室温下超声提取皮革制品中的邻苯二甲酸酯类增塑剂,提取液经中性氧化铝固相萃取柱净化后进行气相色谱-串联质谱分析。该方法简便快速,定性定量准确,灵敏度高,DIDP、DINP和DMPP的定量下限(S/N=10)分别为0.2、0.2、0.1 mg/kg,其余17种邻苯二甲酸酯类增塑剂的定量下限均小于50μg/kg,RSD小于12%,平均加标回收率为86%～95%。采用该方法对47个市售皮革制品进行测定,结果在2个样品中检出多种邻苯二甲酸酯类增塑剂。     

涡旋混合辅助超声提取-高效液相色谱法同时测定水基胶中的苯系物和邻苯二甲酸酯类增塑剂

采用涡旋混合辅助超声提取样品的前处理方式,应用高效液相色谱法同时测定水基胶中的苯系物和5种邻苯二甲酸酯类增塑剂.基于样品基质的属性,采用漩涡混合器混合样品,使样品均匀分散于萃取溶剂中,再使用超声萃取的方式提取目标物.研究了不同萃取溶剂、提取方式及其条件对目标物检测结果的影响.优选了色谱分析所用的流动相、检测波长、流量和进样量等条件.在优化条件下,5种苯系物和5种邻苯二甲酸酯类增塑剂的峰面积与其质量浓度呈线性关系,相关系数(R2)都大于0.997,回收率分别在91.9%~111.4%和88.3%~121.4%之间,相对标准偏差RSD分别在1.41%~2.80%和1.24%~2.94%之之间.检出限分别在0.3~0.6 mg/kg和0.2~0.3 mg/kg之间.研究表明方法简便、耗溶剂量少、准确,与现行标准方法具有较好的吻合性,适合于同时测定水基胶中的苯系物和5种邻苯二甲酸酯类增塑剂.     

气相色谱–质谱法测定纤维板和刨花板中邻苯二甲酸酯类增塑剂

建立气相色谱–质谱方法测定纤维板和刨花板中6种邻苯二甲酸酯的方法。样品用正己烷提取后,采用HP–5MS毛细管柱(30 m×0.25 mm,0.25μm)分离,以内标法进行定量。邻苯二甲酸酯BBP,DBP,DEHP,DNOP在0.2~2μg/m L范围内线性均良好,检出限为2 mg/kg;DINP,DIDP在2.0~20μg/m L范围内线性均良好,检出限为10 mg/kg。线性相关系数均大于0.999。样品加标回收率为86.00%~95.17%,测定结果的相对标准偏差为3.06%~9.72%(n=6)。该方法具有较高的灵敏度,可应用于各类纤维板和刨花板产品中邻苯二甲酸酯类增塑剂的检测。     

Analysis of 16 phthalic acid esters in food simulants from plastic food contact materials by LC‐ESI‐MS/MS

An RP LC‐ESI‐MS/MS method for the determination of the migration of 16 primary phthalic acid esters from plastic samples has been developed using distilled water, 3% acetic acid, 10% alcohol, and olive oil as food simulants. Detection limits were 1.6–18.5 μg/kg in distilled water, 1.4–17.3 μg/kg in 3% acetic acid, 1.4–19.2 μg/kg in 10% alcohol, and 31.9–390.8 μg/kg in olive oil. The RSDs were in the range of 0.07–11.28%. The real plastic products inspection showed that only few analyzed samples were phthalates contaminated. Bis‐2‐ethylhexyl ester and dibutyl phthalate were the common items migrated from the plastic products into food and feeds, but the migration concentrations were far below the limits set by European Union (1.5 mg/kg for bis‐2‐ethylhexyl ester and 0.3 mg/kg for dibutyl phthalate).     

Determination of ink photoinitiators in packaged beverages by gas chromatography-mass spectrometry and liquid chromatography-mass spectrometry

A new analytical method, using gas chromatography-mass spectrometry (GC/MS) and liquid chromatography-mass spectrometry (LC/MS) techniques, was developed for the determination in packaged food beverages of five ink photoinitiator residues: 2-isopropylthioxanthone (ITX), benzophenone, 2-ethylhexyl-4-dimethylaminobenzoate (EHDAB), 1-hydroxycyclohexyl-1-phenyl ketone (IRGACURE 184) and ethyl-4-dimethylaminobenzoate (EDAB). Samples were extracted from selected beverages (milk, fruit juices and wine) and relative packagings, using n-hexane and dichloromethane, respectively, purified on solid-phase extraction (SPE) silica gel cartridges, and then analyzed in GC/MS and LC/MS. The recovery percentages, obtained spiking the beverage samples at concentrations of 4 and 10 microgl(-1) with a standard mixture of photoinitiators, were in the range 42-108% (milk), 50-84% (wine), and 48-109% (fruit juices). The repeatability of the method was assessed in all cases by the % of correlation value, that was lower than 19%. The lowest limits of detection (LODs) and limits of quantification (LOQs), obtained using GC/MS, were in the range 0.2-1 and 1-5 microgl(-1), respectively. The method was applied to the analysis of forty packaged food beverages (milk, fruit juices and wine samples). The most significant contamination was that of benzophenone, found in all samples in a concentration range of 5-217mugl(-1). Its presence was confirmed by an LC/Atmospheric-Pressure PhotoIonization (APPI)/MS/MS analysis. The photoinitiator (EHDAB) was found in eleven out of forty beverages in a concentration range of 0.13-0.8 microgl(-1). Less important was the ITX contamination, found in three out of forty samples in a range 0.2-0.24 microgl(-1). The work proposes a new method to analyze ink photoinitiator residues in polycoupled carton packaging and in contained food beverages.     

Detection of migration of phthalates from agglomerated cork stoppers using HPLC-MS/MS

Agglomerated stoppers are manufactured from natural cork granules and adhesives. Esters, such as phthalates and adipates, are commonly used in adhesives at concentrations of typically 2-5%. Because of this, and regarding consumer safety, it is necessary to ensure that these compounds do not migrate into the beverage where the cork stopper is used. A reversed-phase high performance liquid chromatography method with tandem mass spectrometry detection is developed for the separation of nine phthalates into 12% ethanol, used as simulant of alcoholic beverages. The chromatographic separation was carried out with a Luna C18 (2) HSTcolumn (50 × 3.0 mm, 2.5 μm) with a gradient elution of water/methanol with 0.1% acetic acid at 300 μL min(-1). The method was validated for four selected phthalates: di-butylphthalate, di-isononylphthalate, di-isodecylphthalate, and butyl-benzyl phthalate, with recoveries ranging between 95% and 112% and intralaboratory precision (RSD) between 5 and 14%, depending on the phthalate. The lowest quantification limit, 0.15 mg kg(-1), was achieved for di-butylphthalate. Nevertheless, in all cases, the limits obtained guarantee the method utility if restriction limits set in Commission Regulation No 10/2011 for plastic materials are taken into account.     

Simultaneous determination of trans-resveratrol and sorbic acid in wine by capillary zone electrophoresis

A method for separation and determination of sorbic acid, a food and beverage preservative, and trans-resveratrol, a biomedically active substance, in wine by capillary zone electrophoresis is described. A solid-phase extraction step on C18-column prior to the electrophoretic separation providing lower detection limits was used for trans-resveratrol determination. For determination of sorbic acid direct analysis of wine (without a preconcentration step) was used. The method is rapid and sensitive and was applied to the analysis of wines from Alsace, France.     

Extraction and gas chromatographic evaluation of plasticizers content in food packaging films

Cling films are prepared by adding (5-30% w/w) adipates, citrates, and phthalates. The adverse effects on human health of the plasticizers have been demonstrated, and then their content in food contact plastics and possible migration to foodstuffs must be carefully checked. To offer an easier tool to perform these controls, a Soxhlet extraction by ethyl acetate and a multi residue chromatography analysis, with Flame Ionization Detector, have been optimised for the application in evaluating both the real content of plasticizers in films and freezing bags, and their migrated amounts in simulants. The average extraction yield was 95 ± 10%. The chromatographic analysis was able to determine 16 different compounds, clearly separated, taking only 25 min to complete the assay. The detection limits ranged from 0.07 to 0.7% (w/w). The total amount of plasticizers in the packaging products was comprised between 3 and 10% (w/w). Extracted and migrated amounts were compared, and they resulted in good agreement. No migration of Phthalates, whose presence has been demonstrated in some samples, has been observed. It has been also demonstrated that a prolonged contact (till 60 days) did not increase the amount of migrated plasticizers, and then the risks for health.     

Basalt fibers grafted with a poly(ionic liquids) coating for in‐tube solid‐phase microextraction

To improve the durability and extraction efficiency of an ionic liquid coating, 1‐dodecyl‐3‐vinylimidazolium bromide was polymerized and grafted onto basalt fibers for in‐tube solid‐phase microextraction. To develop an extraction tube, basalt fibers grafted with the poly(ionic liquids) coating were filled into a polyether ether ketone tube with a 0.75 mm inner diameter. The extraction tube was connected to high‐performance liquid chromatography system equipped with a sampling pump to build an online enrichment and analysis system. Using four common phthalates as model analytes, the extraction tube was investigated by the online analysis system. Good enrichment performance was exhibited by high enrichment factors ranging from 851 to 1858. Under the optimum conditions, an online analysis method was established, and good linearity (0.03–12 and 0.15–12 μg/L) and low limits of detection (0.01–0.05 μg/L) were achieved. This analysis method was applied to real samples including water in a disposable plastic box and the bottled water, some targets were detected but not quantified, and the relative recoveries spiked at 2, 5 and 10 μg/L were in the range of 86.4–119.5%.     

Determination of phthalates in wine by headspace solid-phase microextraction followed by gas chromatography-mass spectrometry. Use of deuterated phthalates as internal standards

This study proposes the use of deuterated phthalates as internal standards for the accurate determination of phthalates in wine by headspace solid-phase microextraction followed by gas chromatography-mass spectrometry. Unlike other internal standards proposed previously such as benzyl benzoate, deuterated phthalates enabled matrix-error free determinations to be performed without standard addition because statistically equal slopes were obtained for synthetic, white, rose and red wines. The relative standard deviation values under intermediate precision conditions ranged from 0.24 to 4.6%, and detection limits below 35 ng L(-1) were obtained. Recovery values were around 100% in most of cases and the method provided similar results to standard addition. Finally, the method was used to screen phthalate levels in 10 wine samples.     

前吸附技术-超高压液相色谱-串联质谱法同时测定酒中24种邻苯二甲酸酯

建立了前吸附技术-超高压液相色谱-串联质谱测定酒中24种邻苯二甲酸酯含量的方法。酒类样品经稀释、净化后采用前吸附技术排除仪器管路中的本底干扰,经超高压液相色谱-串联质谱仪进行测定。采用多反应监测模式、电喷雾电离源正离子(ESI⁺)模式进行检测,外标法定量。24种邻苯二甲酸酯在0.005~2.00 mg/L范围内线性关系良好,相关系数(r)均大于0.99,检出限(S/N=3)为0.003~0.05 mg/kg。以不含增塑剂的酒类样品作为空白样品进行加标回收率试验,各种邻苯二甲酸酯化合物的回收率为75.4%~118.2%,相对标准偏差(RSD)为4.0%~11.2%。该法不但可以有效排除管路中邻苯二甲酸酯本底的干扰,而且简单、灵敏、稳定。     

Analysis of polycyclic aromatic hydrocarbons in water and beverages using membrane-assisted solvent extraction in combination with large volume injection-gas chromatography-mass spectrometric detection

Membrane-assisted solvent extraction (MASE) in combination with large volume injection-gas chromatography-mass spectrometry (LVI-GC-MS) was applied for the determination of 16 polycyclic aromatic hydrocarbons (PAHs) in aqueous samples. The MASE conditions were optimized for achieving high enrichment of the analytes from aqueous samples, in terms of extraction conditions (shaking speed, extraction temperature and time), extraction solvent and composition (ionic strength, sample pH and presence of organic solvent). Parameters like linearity and reproducibility of the procedure were determined. The extraction efficiency was above 65% for all the analytes and the relative standard deviation (RSD) for five consecutive extractions ranged from 6 to 18%. At optimized conditions detection limits at the ng/L level were achieved. The effectiveness of the method was tested by analyzing real samples, such as river water, apple juice, red wine and milk.     

Assessment of specific migration to aqueous simulants of a new active food packaging containing essential oils by means of an automatic multiple dynamic hollow fibre liquid phase microextraction system

The determination of specific migration in the three aqueous food simulants (water, 3% acetic acid and 10% ethanol) from experimental active packaging polypropylene-based films containing natural essential oils as active agents has been carried out for the first time by a two-phase hollow fibre liquid phase microextraction (HFLPME). Due to the high number of variables involved, an experimental design has been applied. High throughput, with six samples running simultaneously in a highly automated system working in dynamic extraction mode, has been achieved. The main analytical characteristics are detection limits as low as 0.01 μg kg⁻¹, linearity higher than 0.99 for almost 5 magnitude orders, average precision below 16% as RSD and concentration factors ranging from 4 to 189. Migration of 43 compounds including terpenes, alkanes, plastic additives and degradation compounds is reported. According to the results obtained and European legislation, the packaging prototypes tested could be safely marketed.