TiO2纳米管阵列光电催化氧化处理氨氮废水

用电化学阳极氧化法制备了高度有序的钛基二氧化钛纳米管阵列薄膜。用场发射扫描电镜(FE-SEM)、X射线衍射(XRD)表征样品的形貌与晶型特征。以二氧化钛纳米管阵列为光阳极,石墨为对电极,测试了不同pH值和外加偏压条件下的光电流响应和光电催化氧化降解NH4Cl水溶液(以N计,100 mg·L-1)的效率。结果表明:所制备的TiO2纳米管阵列具有锐钛矿和金红石的混晶结构,且主要晶型为锐钛矿。光电流响应的强弱与光电催化氧化效率的高低相对应,降解氨氮废水的最佳条件为pH=11,偏压为1.0 V。     

二氧化钛纳米晶溶胶内渗透电极对染料敏化太阳能电池的光伏性能的提高

以自制的过氧钛酸(PTA)水溶液为前驱体,用水热法制备了透明锐钛矿相二氧化钛溶胶.无需有机添加剂可得到直径小于7 nm的棒状二氧化钛纳米晶溶胶.通过将溶胶内渗透到染料敏化太阳能电池(DSSCs)的多孔二氧化钛电极后,消除了多孔电极内的大孔并改善了电极内纳米晶之间的连通性.用扫描电子显微镜(SEM)和光学轮廓仪对溶胶内渗透后的光阳极进行了表征.结果表明:小颗粒棒状二氧化钛纳米晶附着在多孔的二氧化钛表面,填充了电极由于烧结产生的大孔,并在多孔的二氧化钛内部形成了有利于电子传输的网络结构.与未经处理的多孔电极相比,改性后的光阳极组装成染料敏化太阳能电池后光电转化效率提高了64%.     

NH4F/H3PO4体系中阳极氧化法制备TiO2纳米管阵列

以价廉的Ni板代替常用的Pt片为阴极,纯钛为阳极,采用电化学阳极氧化法在NH4F-H3PO4体系中制备出TiO2纳米管阵列.详细研究了制备参数(溶液酸度、氟离子浓度、外加电压和氧化时间)对所获纳米管阵列形貌的影响.采用场发射扫描电镜(FE-SEM)和X射线衍射(XRD)对样品的形貌和晶相结构进行了表征.在最优化的条件下,可以获得形貌规整、表面干净、有序的TiO2纳米管阵列.纳米管阵列的平均管径为60 nm.管长约530 nm.采用阳极氧化法制备的纳米管阵列是非晶态的.经400℃热处理2 h后,可以转变为锐钛矿相.实验结果还发现,经过热处理后,纳米管阵列变得更为有序,管径扩大至约95 nm.     

水热法可控合成二氧化钛纳米晶及其在染料敏化太阳能电池中的应用

本文报道了水热法可控合成二氧化钛纳米晶及其在染料敏化太阳能电池中的应用.选择合适的有机碱胶化剂,能很好地控制二氧化钛纳米晶的生长,形成不同形貌和粒径的锐钛矿型二氧化钛纳米晶颗粒.染料敏化太阳能电池光电性能测试结果表明,以四乙基氢氧化铵为胶化剂合成的边长为8～13nm的正方形二氧化钛纳米晶构成的光阳极光电性能优于以四丁基氢氧化铵为胶化剂合成的边长为7～10nm的正方形二氧化钛纳米晶以及长18～35nm,宽10～18nm的长方形二氧化钛纳米晶构成的光阳极.用较高浓度的四甲基氢氧化铵胶化剂能合成球形或椭球形亚微米级二氧化钛颗粒,以其为散射中心在光阳极中构建散射层,染料敏化太阳能电池的光电转换效率能由6.77%提高到8.18%.     

脉冲电沉积法制备Pt-TiO2 纳米管电极及其电催化性能

采用阳极氧化法在高纯钛片上原位组装TiO2纳米管阵列, 然后用脉冲电沉积方法将Pt沉积到TiO2纳米管阵列上, 制备出Pt-TiO2纳米管电极. 利用XRD和SEM对所获电极的微观结构和形貌进行表征, 结果表明, Pt纳米颗粒以花簇状分散在TiO2纳米管上, 晶粒大小约为25.6 nm. 对甲醇的电催化性能的研究结果表明, 脉冲电沉积制得的Pt-TiO2纳米管电极比TiO2纳米管电极和纯Pt片电极具有更高的电催化活性, 是Pt电极的40多倍.     

阳极氧化法制备二氧化钛纳米管阵列的研究

采用电化学阳极氧化法,将纯钛浸入HF酸水溶液,在钛基体表面原位构建高度有序的二氧化钛纳米管阵列,探讨阳极氧化电压、电解液浓度和电解液温度等对二氧化钛纳米管阵列尺寸和形貌的影响。通过SEM、XRD对二氧化钛纳米管阵列的结构特征进行表征,结果表明,不同的阳极氧化电压、电解液浓度和温度都将影响TiO2纳米管阵列的尺寸和形貌,在阳极氧化电压为20V,HF电解液浓度为0.5%t条件下,可制备出结构规整有序的TiO2纳米管阵列。     

TiO2纳米片/巢状分级结构纳米阵列薄膜的制备及其在染料敏化太阳能电池中的应用

采用水热合成法在氟掺杂二氧化锡(FTO)导电玻璃基底上得到TiO2纳米阵列薄膜,并进一步通过NaOH溶液水热处理制备了由巢状纳米阵列及纳米片覆盖层构成的TiO2纳米阵列分级结构一体化薄膜.采用场发射扫描电镜(FE-SEM),X射线衍射(XRD),紫外-可见(UV-Vis)漫反射光谱和吸收光谱技术对TiO2薄膜的结构和性质进行表征.FE-SEM结果表明:分级结构TiO2薄膜膜厚为1.5μm,薄膜由一层纳米片覆盖层(约0.2μm高)和一层巢状纳米阵列层(约1.3μm高)组成.XRD谱图表明TiO2薄膜为锐钛矿相.UV-Vis光谱显示分级结构TiO2薄膜具有较强的光捕获能力和染料吸附能力.TiO2纳米片/巢状分级结构纳米阵列薄膜作为光阳极,可有效地提高染料敏化太阳能电池的光电转换效率,其短路电流(Jsc)为7.79mA·cm-2,开路电压(Voc)为0.80V,填充因子(FF)为0.40,光电转换效率(η)为2.48%,其光电转换效率较TiO2纳米阵列薄膜提高了近10倍.     

TiO_2纳米管阵列薄膜制备及生长机理的研究

本论文采用阳极氧化的方法,在NH4HF2+NH4H2PO4的混合水溶液中于室温下以金属钛为基体原位合成氧化钛纳米管阵列薄膜。讨论了电解液成分、外加电压、溶液的pH值对氧化钛纳米管阵列薄膜微观结构及形貌的影响,并建立了阳极氧化钛纳米管阵列薄膜的生长模型。氧化钛纳米管的结构与外加电压有很大的关系,只有电压在5～35V范围内才能制备出二氧化钛纳米管阵列薄膜,其管径随着电压的升高而增加,且管径范围为30～160nm。而薄膜的厚度与电解液有关,通过控制电解液的成分及pH值,可获得厚度为6.5μm的氧化钛纳米管阵列薄膜。     

导电玻璃上室温沉积钛膜及TiO2纳米管阵列的制备与表征

在掺氟的杂nO2(FTO)导电玻璃衬底上采用射频磁控溅射的方法室温沉积纯Ti薄膜, 以NH4F/甘油为电解液, 经电化学阳极氧化得到结构有序、微米级的TiO2纳米管阵列/FTO复合结构, 并通过场发射扫描电子显微镜(FESEM)、X射线衍射(XRD)以及光电化学的方法对纳米管阵列进行了表征. 研究表明, 在氩气气压为0.5 Pa, 功率为150 W, 时间为0.5 h条件下在导电玻璃上室温沉积获得钛膜的结构为晶带T型组织, 表面均匀性好且致密度较高; 在电压为30 V下, 随着阳极氧化时间从1 h延长至3 h, 纳米管的管径从50 nm增加到75 nm, 纳米管的长度从750 nm增至1100 nm后减至800 nm, 管壁由平滑变为波纹状; 随氧化电压的升高, 纳米管管径逐渐增大, 而表面覆盖物逐渐减少, 可通过在稀的HF溶液(0.05%(w, 质量分数))中超声清洗去除; 此外, 瞬态光电流测试表明结晶的电极表现出更好的光电转换性能, 紫外光照射下能促进TiO2光生载流子有效分离, 在热处理温度为450 ℃时, 具有较高的光电化学性能.     

导电玻璃上室温沉积钛膜及TiO2纳米管阵列的制备与表征

在掺氟的SnO2(FTO)导电玻璃衬底上采用射频磁控溅射的方法室温沉积纯Ti薄膜,以NH4F/甘油为电解液,经电化学阳极氧化得到结构有序、微米级的TiO2纳米管阵列/FTO复合结构,并通过场发射扫描电子显微镜(FESEM)、X射线衍射(XRD)以及光电化学的方法对纳米管阵列进行了表征.研究表明,在氩气气压为0.5Pa,功率为150W,时间为0.5h条件下在导电玻璃上室温沉积获得钛膜的结构为晶带T型组织,表面均匀性好且致密度较高;在电压为30V下,随着阳极氧化时间从1h延长至3h,纳米管的管径从50nm增加到75nm,纳米管的长度从750nm增至1100nm后减至800nm,管壁由平滑变为波纹状;随氧化电压的升高,纳米管管径逐渐增大,而表面覆盖物逐渐减少,可通过在稀的HF溶液(0.05%(w,质量分数))中超声清洗去除;此外,瞬态光电流测试表明结晶的电极表现出更好的光电转换性能,紫外光照射下能促进TiO2光生载流子有效分离,在热处理温度为450℃时,具有较高的光电化学性能.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.