神府煤液化油加氢精制过程中硫氮化合物分布的变化

采用实沸点蒸馏对神府煤液化油及其加氢精制油做了馏分切割,并采用GC-PFPD与GC-NCD对液化油与精制油中的硫氮化合物类型进行了分析,研究了液化油加氢精制过程中硫氮化合物分布的变化。结果表明,液化油中硫含量随窄馏分的馏程由低到高呈现"U"型分布,氮的分布基本上随窄馏分沸点温度的升高而增大,氮的含量远高于硫的含量;经过固定床加氢精制后,97%的硫和98.9%的氮得到脱除。液化油中苯并噻吩和二苯并噻吩等二环和三环化合物占93.25%;经过加氢处理之后,硫醇、硫醚、噻吩类等低沸点含硫化合物基本消失,难脱除组分主要以苯并噻吩类、二苯并噻吩类为主。液化油中含氮化合物主要以五元杂环中性氮化物为主,占54.96%;碱性氮化物主要以苯胺类为主,占23.22%,喹啉类相对较少;经过加氢处理之后,脂肪胺类含氮化合物被完全脱除,精制油中残留的氮主要以碱性氮化物喹啉类与苯胺类含氮化合物存在。     

宝明页岩柴油碱性氮化物的梯度富集及GC-MS分析

利用溶剂萃取和柱色谱等技术浓缩分离新疆宝明页岩油柴油馏分中的碱性氮化物。以宝明页岩柴油为原料,经糠醛溶剂精制,初步得到富集碱性氮化物的抽出油。以抽出油为深度富集碱性氮化物的原料,采用柱色谱等分离方法,从抽出油中分离得到碱性氮化物。利用傅立叶变换红外光谱仪(FT-IR)和气相色谱-质谱联用仪(GC-MS)分别对富集的碱性氮化物进行官能团检测和定性、定量分析。结果表明:新疆宝明页岩油柴油馏分中的碱性氮化物经溶剂精制和柱色谱等分离方法梯度富集后,碱性氮化物的质量分数由抽出油的12.08%提高到最终产物的69.48%,并在富集分离的产物中鉴定出60种碱性氮化物,其中主要为苯胺类、喹啉类和吡啶类化合物,各占25.85%,23.56%和16.52%。     

重油催化裂化汽油中含氮化合物的分析

利用酸萃取技术浓缩分离重油催化裂化（RFCC）汽油中的氮化物，比较了两种萃取剂和两种油剂比对分离效果的影响，结果发现选用10％（体积分数）HCl作萃取剂，油剂比为10：1（体积比）时，碱性氮化物的提取率较高；浓缩分离出的氮化物用色谱－质谱联用方法对其进行了检测，结果表明RFCC汽油中的氮化物主要是C0－C2苯胺及少量吡啶类、喹啉类碱性氮化物。     

中心切割GC-MS法分析煤液化油中的酚类化合物

使用碱洗提酚法提取煤液化油中的酚类化合物,然后结合Deans Switch装置和LTM色谱柱模块,采用中心切割气相色谱(GC)-质谱(MS)法对提取的酚类化合物进行定性。采用GC建立标准曲线,对煤液化油中主要酚类化合物的质量分数进行测定,并测定了煤液化油中邻甲基苯酚、2-乙基苯酚、4-丙基苯酚和5-茚酚4种酚类化合物的加标回收率。结果表明,在煤液化油中共定性出51种酚类化合物,测定了其中的35种酚类化合物的质量分数,其量占煤液化油总量的2.54(wt)%,苯酚和烷基苯酚占35种酚类化合物的88.2(wt)%。煤液化油中4种酚类化合物的加标回收率高,重复性好。     

中心切割GC-MS法分析煤液化油中的酚类化合物

使用碱洗提酚法提取煤液化油中的酚类化合物,然后结合Deans Switch装置和LTM色谱柱模块,采用中心切割气相色谱(GC)-质谱(MS)法对提取的酚类化合物进行定性。采用GC建立标准曲线,对煤液化油中主要酚类化合物的质量分数进行测定,并测定了煤液化油中邻甲基苯酚、2-乙基苯酚、4-丙基苯酚和5-茚酚4种酚类化合物的加标回收率。结果表明,在煤液化油中共定性出51种酚类化合物,测定了其中的35种酚类化合物的质量分数,其量占煤液化油总量的2.54(wt)%,苯酚和烷基苯酚占35种酚类化合物的88.2(wt)%。煤液化油中4种酚类化合物的加标回收率高,重复性好。     

变色硅胶吸附脱除模拟柴油中各种碱性氮化物

研究了变色硅胶吸附脱除氮含量为960.56μg/g模拟柴油中的碱性氮化物喹啉、苯胺和吡啶。比较了氧化铝、硅藻土、硅胶及变色硅胶对模拟柴油中喹啉的吸附脱除效果。采用XRD、低温N_2吸附-脱附和NH_3-TPD等方法对硅胶和变色硅胶进行了表征。考察了粒径、吸附温度、吸附时间、剂油质量比及共存芳香化合物(萘、苯或甲苯)对变色硅胶吸附脱除各种碱性氮化物的影响。变色硅胶吸附脱除碱性氮化物的顺序均为苯胺吡啶喹啉。吸附时间对三种氮化物的吸附脱除没有影响;吸附温度、变色硅胶粒径和共存芳香化合物对苯胺和吡啶的吸附脱除效果影响不大,对喹啉的吸附脱除效果影响较为明显;剂油质量比对三种氮化物的吸附脱除影响均较大,尤其是对喹啉影响最大。结果表明,变色硅胶吸附各种氮化物时Co能够与其中的N原子形成配位络合吸附。经焙烧再生,变色硅胶几乎完全恢复了对喹啉和吡啶的吸附脱除能力,并可多次再生,但变色硅胶再生后对苯胺的吸附能力损失较大。     

喹啉加氢脱氮产品的气相色谱分析

在煤液化过程中,煤中的少量杂原子(如氮、硫等)转移到煤液化油中,严重影响产品的工业应用。一般以加氢精制来脱除杂原子以制取洁净的燃料。根据文献报导,喹啉、喹啉系及其衍生物在煤液化严品的碱性氮化物中占的比例较大,而且又属于较难脱除的化合物,故在催化剂评选及选择工艺过程最佳条件的研究中往往采用喹啉作为模型化合物,并考察加氢精制过程中氮的分布、脱除效果和脱氮反应机理等。     

Ag+改性NaY分子筛的制备及其吸附脱氮性能研究

采用Ag⁺改性NaY分子筛成功制备了AgY分子筛,利用XRD射线衍射、FT-IR、N₂吸附-脱附对NaY和AgY分子筛进行了表征,并用于吸附脱除模拟燃料中吡啶、苯胺、喹啉碱性氮化物,AgY分子筛的吸附能力明显优于NaY分子筛。考察了吸附温度、吸附时间对AgY分子筛吸附三种氮化物的影响,实验结果表明,吸附能力均为：苯胺>喹啉>吡啶,为了进一步研究其吸附机理,采用Materials Studio软件建立了AgY分子筛12T团簇模型并在303、323、343 K下模拟三种氮化物分子在AgY分子筛上的吸附,计算了吸附能、活性中心与吡啶、苯胺、喹啉分子的距离、前线轨道、等密度分布、径向分布函数等相关参数,计算结果也表明,AgY分子筛对苯胺的吸附优于喹啉,优于吡啶,与实验结果一致,且吸附以化学吸附为主,AgY分子筛S位和W位为主要吸附位。吸附等温线研究结果表明,AgY分子筛对吡啶的吸附符合Langmuir-Freundlich混合吸附模型,对苯胺、喹啉的吸附符合Freundlich吸附模型。吸附动力学和吸附热力学结果表明,AgY分子筛对吡啶的...     

白石湖煤液化粗油加氢精制过程硫、氮化合物转化规律

采用实沸点蒸馏仪对白石湖煤液化油进行馏分切割,切取<170℃液化粗油进行加氢精制脱除其中硫、氮化合物,采用硫化学发光气相色谱仪（GC-SCD）、氮化学发光气相色谱仪（GC-NCD）对液化粗油和精制油中硫、氮化合物进行分析表征,研究加氢精制过程硫、氮化合物的转化规律。结果表明,液化粗油中含硫化合物主要是噻吩类化合物和硫醇,经过加氢精制后基本消失,苯并噻酚类化合物脱除比例要低于噻吩类化合物,属于较难脱除含硫化合物。液化粗油中含氮化合物主要是苯胺类化合物,其次是吲哚类化合物,经过加氢精制吲哚类化合物全被脱除,苯胺和喹啉类化合物属于碱性含氮化合物,是精制油中残留的主要含氮化合物,含量达1.61 mg/kg。     

固相萃取/气相色谱-质谱分析催化裂化柴油中的含氮化合物

采用固相萃取技术分离富集催化裂化柴油中的中性和碱性含氮化合物,优化了洗脱溶剂的种类及用量,并考察了分离方法的回收率和重复性。结果表明,二氯甲烷和丙酮-二氯甲烷可以有效分离富集柴油中的中性和碱性含氮化合物;固相萃取法的回收率高达99. 5%,3次分离实验结果的相对标准偏差均小于4%。分离后的组分采用气相色谱-质谱(GC-MS)定性,数据表明,催化裂化柴油中的中性含氮化合物主要为C0～C3-吲哚及C0～C5-咔唑,碱性含氮化合物主要为C1～C4-苯胺及C0～C2-喹啉。采用气相色谱-氮化学发光检测器对含氮化合物进行定量,发现中性含氮化合物占已定性含氮化合物总量的96. 6%;咔唑类含氮化合物的含量最高,占已定性含氮化合物总量的64. 3%;从化合物结构上看,化合物含量随着甲基取代基数目的增多呈先增加后降低的趋势。该方法可用于催化裂化柴油中含氮化合物的类型分布分析。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.