双环戊二烯加氢异化合成金刚烷

采用固定反应器考察了双环戊二烯连续催化加氢合成桥式氢双环戊二烯反应性能,筛选出具有良好催化性能的23％Ni/γ-AI2O3催化剂。以桥式四氢双环戊二烯为原料,采用不同类型的沸石催化剂研究了金刚烷的合成,并考察了沸石骨架阳离子改性和表面负载过渡金属等对其催化性能的影响。在n(cat)/n ( reactant)=0.25,p(H2)=1.1MPa,θ=250℃,t=3h的条件下,采用三元负载型催化剂0.8%Pt-0.2%Re-3%Co/ReUSY 可得到收率为27．7％的金刚烷。     

高活性固载化三氯化铝催化合成金刚烷

首次用固载化AlCl3催化剂催化桥式四氢双环戊二烯异构化反应合成金刚烷.结果表明,以γ-Al2O3为载体的固载化AlCl3催化剂在较低的反应温度(140℃)下具有较高的催化活性和生成金刚烷的选择性,桥式四氢双环戊二烯的转化率达到100%,金刚烷的选择性为17.7%;而以Si O2作为载体制备的催化剂,几乎没有金刚烷生成.     

双环戊二烯固定床加氢催化体系研究

本文对双环戊二烯固定床连续催化加氢合成四氢双环戊二烯进行了研究。通过对催化剂载体γＡｌ２Ｏ３不同表面预处理方法的研究，催化剂活性组分元素的评选，研制出适合该催化加氢体系的负载型镍系催化剂ＡＰＣ２，其Ｎｉ负载量１５％，载体是经表面物理化学预处理后的γＡｌ２Ｏ３。在此基础上确定了最佳活化程序。通过对该反应体系工艺条件的研究，较佳的工艺参数为：Ｔ１５０～１６０℃，ＰＨ：１．０ＭＰａ，ＳＶ：２０～３０ｈ１，Ｈ２／ＤＣＰＤ３（ｍｏｌ）。此时双环戊二烯转化率大于９８％，四氢双环戊二烯的收率可达９５％。     

AlCl3/MCM-41催化剂上桥式四氢双环戊二烯异构化反应

 分别采用介孔 MCM-41 和 SiO2 为载体制备了固载化 AlCl3 催化剂, 考察了其催化桥式四氢双环戊二烯异构化生成挂式四氢双环戊二烯反应性能. 结果表明, 180 °C 时 AlCl3/MCM-41 催化剂上挂式四氢双环戊二烯选择性可达 95.7%, 而在 AlCl3/SiO2 上仅为 86.3%. 采用 N2 吸附-脱附、Hammett 指示剂法、吡啶吸附红外光谱和化学分析等方法对催化剂进行了表征. 结果表明, AlCl3/MCM-41 催化剂较弱的表面酸性和一维孔结构有利于挂式四氢双环戊二烯的生成.     

双环戊二烯开环歧化聚合反应及合成聚合物性能研究

采用WCl6－ArOH／Et2AlCl（ArOH：2，6-二叔丁基对甲苯酚）催化体系进行了双环戊二烯的开环歧化聚合反应，考察了单体纯度以及催化体系支载化对聚合反应和合成聚合物性能的影响。在极限聚合浓度下，研究了单体与主、助催化剂摩尔比等因素对聚合反应及合成聚合物性能的影响。实验结果表明：单体纯度越高所得聚合物的机械性能越好；催化体系经聚合物支载化后能显著提高催化体系的催化聚合活性及合成聚合物的机械性能。     

双环戊二烯苯酚树脂的合成新工艺

以双环戊二烯（DCPD）和苯酚为原料,甲磺酸为催化剂,合成了双环戊二烯苯酚树脂。适宜工艺条件:苯酚与DCPD摩尔比为5、反应温度120 ℃、反应时间5 h、催化剂质量分数为1.5%,收率89%。所得的双环戊二烯苯酚树脂（DPR）经催化加氢法在H2气压力1.5 MPa、催化剂Pd/Al2O3用量为原料质量分数的0.5%、反应温度80 ℃条件下对树脂进行脱色处理。 得到浅黄色双环戊二烯苯酚树脂,收率89%,经IR和1H NMR表征分析其为目的产物,产物指标达到国际同类产品的质量标准。     

改性纳米ZSM－5催化剂脱除汽油中烯烃的性能

 在考察ZSM－5沸石晶粒大小对脱除汽油中烯烃的影响的基础上，用纳米ZSM－5沸石作为活性组分负载Co－Mo氧化物制备了改性纳米ZSM－5沸石催化剂，并用XRF，NH3－TPD和TEM等方法对催化剂进行了表征．以脱除DCC汽油中的烯烃为探针反应，临氢条件下，在固定床反应器上对催化剂脱除烯烃的性能进行了评价，考察了反应温度、压力、质量空速和氢／油比对催化剂脱除烯烃性能的影响．结果表明，由于纳米ZSM－5沸石具有晶粒小、微孔短、扩散路程短以及表面酸中心数量多等特点，因而表现出较高的催化活性和较强的抗积碳性能．在V（H2）／V（oil）＝300，WHSV＝3h－1，p（H2）＝3．0MPa和θ＝350℃的适宜条件下，DCC汽油中烯烃的含量由60．7％下降到40％左右，芳烃和烷烃的含量增加；在脱除烯烃的同时可维持汽油的辛烷值不降低．催化剂连续运行1000h以上，其脱除烯烃的性能稳定．     

双环戊二烯开环歧化聚合反应催化体系的配位体效应研究

用WCl6－Et2AlCl催化体系进行双环戊二烯的开环歧化聚合反应，考察了催化体系的配体效应。实验结果表明在催化体系中添加位阻酚—2．6-二叔丁基-对甲苯酚（DTBC）能明显提高聚合反应的转化率和合成聚合物的机械性能（如冲击强度、拉伸强度等）。利用位阻高分子酚──线形酚醛树脂（LPF）作为配体也得到类似的结果。     

Mo／La－Co－O催化剂上甲烷选择氧化制甲醇反应

 制备了一系列Mo／La－Co－O催化剂，考察了催化剂对甲烷选择氧化制甲醇反应的催化性能，并用BET，XRD，LRS，H2－TPR和XPS等技术研究了催化剂的结构和性质．结果表明，在n（CH4）∶n（O2）∶n（N2）＝10∶1∶1，SV＝14．4L／（g·h），p＝4．2MPa和θ＝420℃的反应条件下，7％Mo／La－Co－O催化剂表现出较好的催化性能，甲醇选择性为60％，甲醇收率为6．7％．Mo负载于La－Co－O上以后，Mo－O物种以无定形的状态存在于La－Co－O表面，并与La－Co－O发生相互作用．Mo的负载量影响Mo－O物种的结构及催化剂的性质．催化剂的还原性和表面O－／O2－比影响催化剂上甲烷选择氧化制甲醇反应的性能．     

乙烯直接氧化制乙酸的研究Ⅱ．助剂对Pd－Se／H4SiW12O40／SiO2催化性能的影响

 研究了不同助剂促进的负载型Pd－Se／H4SiW12O40／SiO2催化剂对乙烯直接氧化制乙酸反应的影响．采用固定床微反装置评价了催化剂的性能，并采用C2H4和O2吸附量测定、吸附C2H4的TPD－MS和TPSR－MS等技术对催化剂进行了表征．结果表明，以SiO2为载体，以硅钨酸为助剂，Pd－Se－Na－Ru组成的催化剂体系其催化性能比文献报道的结果明显提高．在原料气配比n（C2H4）∶n（N2）∶n（O2）∶n（H2O）＝55∶14∶9∶22，反应物空速GHSV＝3844h－1，反应压力p＝1．4MPa，反应温度θ＝155℃条件下，乙烯的转化率和乙酸的选择性分别为8．0％和87．4％，乙酸的单程时空产率达372．0g／（L·h）．吸附量测定表明，吸附在催化剂表面上的C2H4／O2比值高对于提高乙酸的选择性是有利的．     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.