疏水性有序介孔氧化硅薄膜的制备

采用溶胶−凝胶技术并结合蒸发诱导自组装工艺, 以三嵌段共聚物EO₂₀PO₇₀EO₂₀ (P123)为模板剂, 使用浸渍提拉法制备了有序介孔氧化硅薄膜, 并使用不同的表面修饰剂对薄膜进行表面处理, 制备了疏水性有序介孔氧化硅薄膜. 利用FT-IR、小角XRD、HRTEM分别表征薄膜的化学物种和孔结构, 探讨了热处理温度和老化时间对薄膜介孔结构的影响, 通过接触角测试研究薄膜的疏水性能, 考察了修饰剂种类、修饰浓度和修饰时间对薄膜疏水性的影响, 结果表明所制备的薄膜为高度有序的介孔氧化硅薄膜, 孔径大小约为8 nm|表面修饰对薄膜的有序性有一定影响, 经三甲基氯硅烷(TMCS)和g-氨丙基三乙氧基硅烷(KH-550)修饰后的薄膜具有很好的疏水性能, 接触角分别为112°和96°|修饰后薄膜的水汽稳定性良好, 仍能保持有序介孔结构, 孔径达7.5 nm, 接触角达93°.     

PET表面锐钛矿-板钛矿相TiO2薄膜的制备及表征

利用改进的溶胶-凝胶法在经表面改性的PET(聚对苯二甲酸乙二醇酯)表面制备得到TiO2薄膜. 利用X射线衍射(XRD)、原子力显微镜(AFM)、UV-Vis 透光率曲线、接触角测试仪等测试手段对TiO2样品的性能进行表征.结果表明, PET表面过渡层的引入有效地改善了有机基底与无机薄膜之间的界面相容性, 在其表面形成透明、均一、附着力良好且具有光催化活性的TiO2薄膜.通过控制实验过程, 在低温下成功制备了不同锐钛矿/板钛矿比的TiO2薄膜,同时发现适量板钛矿相的存在能有效提高薄膜的光致亲水性.     

医用多孔NiTi合金表面溶胶-凝胶法制备TiO2涂层

采用溶胶-凝胶法结合浸渍提拉工艺在多孔NiTi合金表面制备出了结构均一的锐钛矿型TiO2涂层,并在溶胶中添加聚乙二醇(PEG)作为造孔剂,进而在多孔NiTi合金表面制备出内层致密、外层多孔的TiO2复合涂层。SEM分析结果表明,TiO2涂层均匀地覆盖了多孔NiTi合金基体的外表面以及孔的内表面。Hanks溶液中的阳极极化曲线结果表明,与未处理的多孔NiTi合金相比,具有致密TiO2涂层的多孔NiTi合金其耐腐蚀性能有了显著提高。而多孔TiO2复合涂层进一步增大了多孔NiTi合金的实际表面积,提高了材料表面的生物活性。     

Sr2+-TiO2薄膜的制备及超亲水性

以钛酸丁酯作为前驱物,采用溶胶-凝胶法及浸渍-提拉法在载玻片上制备SrO-TiO2薄膜。通过X射线衍射和红外光谱等测试技术表征了SrO-TiO2粉末的结构,用紫外可见分光光度计测定薄膜的透光率,用接触角测试仪测定水与薄膜的接触角。结果表明,掺杂适量Sr2+后,SrO-TiO2粉末中TiO2晶粒的尺寸变小,SrO-TiO2薄膜表面吸附的羟基含量增多且稳定,可提高TiO2薄膜的超亲水性。经紫外光照１ｈ或自然光照５ｈ后,掺杂Sr2+（摩尔分数））为1.0％的SrO-TiO2薄膜与水的接触角接近于0°,表现出良好的亲水性。     

二氧化钛/聚乙烯吡咯烷酮纳米复合薄膜的制备与表征

采用溶胶-凝胶法(so1 gel)制备了TiO2/聚乙烯吡咯烷酮(PVP)有机 无机纳米复合薄膜.采用扫描电子显微镜、接触角测定仪、红外光谱仪、紫外 可见吸收光谱仪和静 动摩擦系数测定仪对所制备的TiO2/PVP纳米复合薄膜进行了结构表征和性能研究.结果表明:所制备的TiO2/PVP纳米复合薄膜表面平整光滑、无裂纹、具有一定的疏水性、良好的透明性、防紫外线性能和减摩抗磨性能.     

TiO2修饰的镍基光电极的制备及光电化学性能

通过溶胶 凝胶法，直接在导电的金属镍基上制备多孔TiO2纳米薄膜，利用STM观察电极的表面形貌，所制TiO2粒径约为20～80 nm，随着烧结温度的升高，TiO2纳米薄膜表面孔的数量增多、孔径增大.用循环伏安法分析了电极的光电化学性能，结果表明，电极的光电响应随烧结温度的升高和薄膜厚度的增加而增大.     

TiO2薄膜优化对染料敏化太阳电池性能的影响

纳米TiO2多孔薄膜微结构对染料敏化太阳电池(DSC)光伏性能有很大的影响。本文采用不同实验和测试方法研究和分析了溶胶-凝胶法制备纳米TiO2颗粒时的热处理温度、TiO2多孔薄膜厚度、纳米TiO2大颗粒光散射、TiCl4溶液处理和电沉积致密TiO2层对纳米多孔薄膜电极和染料敏化太阳电池光伏性能的影响,得到了最佳的优化条件,为纳米TiO2薄膜材料的批量化制作打下了良好基础。     

BPA对低温制备锐钛矿型TiO2薄膜表面形貌的控制

采用4,4’-二羟基二苯基丙烷(BPA)作为TiO2薄膜表面形貌控制的模板剂. 将BPA的乙醇溶液与具有锐钛矿晶粒的TiO2溶胶均匀混合制得涂膜液, 采用浸渍提拉法制备薄膜; 用无水乙醇将薄膜中的BPA选择性溶解去除, 实现了低温下锐钛矿型TiO2薄膜的制备及其表面形貌的调控. 采用SEM考察了TiO2溶胶用量、BPA用量、以及无水乙醇用量等因素对TiO2薄膜表面形貌的影响, 并对其控制机理进行了探讨. 结果表明, 涂膜液的组成会影响到湿膜烘干过程中粒子的迁移和聚集, 从而改变TiO2与BPA 在薄膜表面的分布状态, 最终对TiO2薄膜的表面形貌产生影响. 随BPA浓度的降低,其影响逐渐由薄膜内部转向薄膜的表面区域. 而低TiO2胶粒浓度和高乙醇含量则有利于TiO2薄膜产生粗糙的形貌或多孔性的结构.     

掺杂铈对玻璃表面TiO_2薄膜上油酸光催化降解的影响

采用旋转涂膜工艺 ,以溶胶 凝胶法在玻璃表面制备了掺杂铈的TiO2 薄膜 .利用高压液相色谱、紫外 可见光分光光度计、扫描电镜和能谱仪等手段对掺杂铈的TiO2 薄膜进行了表征 ,考察了掺杂铈对油酸光催化降解效率及TiO2 薄膜表面晶粒分布的影响 ,并对薄膜的化学成分进行了定性和定量分析 .结果表明 ,掺杂 3%Ce的TiO2 薄膜对油酸有最高的光催化降解效率 ,40 0℃为掺杂铈TiO2 薄膜的最佳热处理温度     

二氧化硅溶胶的形成与硅胶膜性能

采取溶胶-凝胶成膜技术,以正硅酸乙酯(TEOS)为原料,分别以水为溶剂NH3催化、乙醇为溶剂HCl催化和冰醋酸为溶剂各自制备出粒状结构、簇状结构和网状结构的二氧化硅溶胶,丙三醇作为添加剂与TEOS水解中间体以氢键结合控制二氧化硅溶胶形态,聚乙烯醇(PVA)与二氧化硅溶胶形成有机/无机互穿网络结构,易于成膜。热处理能使二氧化硅凝胶薄膜中的添加剂逸出并形成疏松结构,塑性形变使硅胶薄膜形成多孔、疏松、致密结构二氧化硅薄膜。实验表明,催化剂和溶剂效应直接影响着二氧化硅溶胶微观结构,从而影响着所形成的硅胶薄膜的微结构。多孔硅胶膜的平衡吸湿量是致密硅胶薄膜的3倍;而疏松结构的硅胶薄膜的吸湿量高于多孔硅胶薄膜的吸湿量,且其吸附速率明显大于多孔硅胶薄膜的吸附速率。     

TiO2纳米粒子膜的表面态性质及其光催化活性的研究

TiO₂纳米粒子膜催化剂光催化降解水中污染物,与粉末相比具有可重复使用、易回收等优点,近年来,在光化学领域受到人们的高度重视^[1～3].膜催化剂的表面性质与其光催化活性直接相关,研究这些性质能够为研制、开发高效催化剂提供理论依据.本文采用TiCl₄水解法,制备了酸性、碱性条件下TiO₂纳米粒子膜.利用原子力显微镜(AFM)、X-射线衍射谱(XRD)、红外光谱(IR)和场诱导表面光电压谱(EFISPS)测定其表面微结构.考察了它们对苯酚降解的光催化活性,讨论了膜催化剂的表面性质对光催化活性的影响.     

Preparation and characterization of highly photoactive nanocrystalline TiO_2 powders by solvent evaporation- induced crystallization method

Highly photoactive bi-phase nanocrystalline TiO2 photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO2 photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO2 at 100℃. When calcination temperatures are below 600℃, the prepared TiO2 powders show bimodal pore size distributions in the mesoporous region. At 700℃, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100℃, the obtained TiO2 photocatalyst by this method shows good photocatalytic activity, and at 400℃, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact t     

阳极氧化水解法制备TiO2纳米膜

TiO2在光电化学电池领域已成为比较重要的半导体材料，自从1972年，Fuishima和Honda首次把TiO2电极用于光电解水以来，人们已经使用多种方法，如化学气相沉积、TiO2粉的烧结、RF射频溅射、等离子体喷涂或用胶体TiO2涂膜等各种方法，来制备单晶（金红石），多晶（金红石、锐钛矿     

Dye-sensitized solid-state solar cells fabricated by screen-printed TiO_2 thin film with addition of polystyrene balls

The screen-printed nanoporous TiO2 thin film was employed to fabricate dye-sensitized solid-state solar cells using CuI as hole-transport materials. The solar cell based on nanoporous TiO2 thin film with large pores formed by the addition of polystyrene balls with diameter of 200 nm to the TiO2 paste exhibits photovoltaic performance enhancement, which is attributed to the good contact of CuI with surface of dye-sensitized thin film due to easy penetration of CuI in the film with large pores.     

TiO2纳米粒子膜的制备、表面态性质和光催化活性

在酸性和碱性条件下,用TiCl4水解法制备了TiO2纳米粒子膜催化剂.采用原子力显微镜(AFM),X射线衍射(XRD),表面光电压谱(SPS)和场诱导表面光电压谱(EFISPS)测定了催化剂表面的微结构及能级结构.对催化剂进行了光催化降解苯酚实验,测定了其光催化活性.结果表明,酸性条件下制备的TiO2膜催化剂的光催化活性较高,其结果接近于P25.用能带理论解释了TiO2纳米粒子膜催化剂光催化活性的差异,分析了膜厚对光催化活性的影响.     

Three-phase system in solvent bar microextraction: An approach for the sample preparation of ionizable organic compounds prior to liquid chromatography

In this article, a simple new solvent microextraction technique is described for the extraction of ionizable organic compounds. This involves performing simultaneous forward- and back-extraction across an organic film immobilized in the pores of a porous polypropylene hollow fiber. Four chlorophenoxyacetic acid herbicides were chosen as model compounds. The target compounds are extracted from the stirred acidic aqueous sample (adjusted to 0.5 M HCl; donor phase) through a thin film of an organic solvent residing in the pores of a polypropylene hollow fiber; they are then finally extracted into another alkaline aqueous phase (1 M NaOH; acceptor phase). Both ends of the fiber are pressure-sealed. The acceptor phase was analyzed by liquid chromatography (LC). This method gave good enrichment (by a factor of 438-553) of the analytes in 40 min extraction time with reasonably good reproducibility. The analytical potential of the method was demonstrated by applying the method to spiked river water sample.     

聚苯乙烯-嵌段-聚丁二烯有序多孔膜在可收缩膜上的形变研究和光学性质

利用溶剂散逸自组装法在潮湿的条件下,制备了聚苯乙烯-聚丁二烯嵌段聚合物（PS-b-PB）有序多孔膜。 利用聚乙烯可收缩膜将PS-b-PB多孔膜进行两次收缩,形成小孔径的有序多孔膜。 通过收缩,膜上的孔由圆形变为长方形或者梭形,孔的尺寸从微米级收缩至亚微米级。 利用扫描电子显微镜对膜收缩过程中2种形状产生的机理进行了研究。 结果表明,PS-b-PB结合了聚苯乙烯（PS）和聚丁二烯（PB）两个均聚物的优点,收缩后仍然保持膜结构的平整性,从而将不可见的热场变化转变为可见的光学变化。     

Nonlithographic micro- and nanopatterning of TiO2 using polymer stamped molecular templates

The polymer-on-polymer stamping technique was used to template patterned TiO2 onto polymer thin films. Polystyrene-b-polyvinyl pyridine diblock copolymer (PS-b-PVP) was stamped on a layer-by-layer assembled thin film of poly(allylamine hydrochloride) and poly(acrylic acid). After rinsing the surface with a good solvent for the block copolymer, an adsorbed PS-b-PVP monolayer remained on the polyelectrolyte film, resulting in a pattern of alternating hydrophobic and carboxylic acid containing hydrophilic regions. The surface was used as a template for the selective deposition of TiO2 on the multilayer surface, using an acid-catalyzed hydrolysis of(NH4)2TiF6. Using this novel approach, we have successfully demonstrated the patterning of TiO2 film on a polyelectrolyte multilayer. Finally, nanoscale features consisting of 200 nm lines alternating with a 350 nm period was accomplished. This paper represents the first such attempt to create an all-polymer nonlithographic template for the directed deposition of TiO2 or related metal oxides; this technique, which utilizes the versatile polyelectrolyte multilayer process, enables the construction of complex polymer-inorganic microstructures suitable for electrooptical and photonic applications.     

Hydrolysis and Polymerization of Dimethyldiethoxysilane, Methyltrimethoxysilane and Tetramethoxysilane in Presence of Aluminum Acetylacetonate. A Complex Catalyst for the Formation of Siloxanes

Hydrolysis and polymerization of dimethyldiethoxysilane (DMDE), methyltrimethoxysilane (MTMS) and tetramethoxysilane (TMOS) in the presence of aluminum acetylacetonate (Al(acac)₃) have been investigated by infrared and NMR spectroscopy. In the absence of acidic catalyst, Al(acac)₃ catalyzes the hydrolysis of all the silanes. The catalytic activity of Al(acac)₃ is less than that of HNO₃, but larger than that of NH₃. The hydrolysis rate increases with increasing concentration of Al(acac)₃ in DMDE. The hydrolysis of TMOS occurs rapidly after an inductive period, which becomes longer with addition of Al(acac)₃. The results are explained by assuming an Al(acac)₃ catalyzed hydrolysis and a silanol catalyzed hydrolysis. The addition of Al(acac)₃ causes changes in polymerization of the resultant silanols. In DMDE and MTMS, it stabilizes the silanols at the early stage, and then enhances their polymerization. The polymerization in TMOS leads to the formation of precipitates that have a high degree of polymerization. The polymerization appears to proceed via a deprotonation mechanism including transfer of protons from silanols to Al(acac)₃. The present results strongly suggest that, besides acids and bases, metal complexes can be used as catalysts for the formation of siloxanes under ambient conditions.     

Latex Surface and Bulk Coagulation Induced by Solvent Vapors

Latex exposure to solvent vapors leads to highly specific changes in latex stability as well as on the morphologies of the particle association products, depending on the latex and solvent used. Examples of solvent vapor-induced aggregation are given: surface films are obtained on two PS latexes; in one case, the film surface is mirror-reflective and very flat, as evidenced by AFM. Another PS latex coagulates under exposure to acetone vapors, and the morphologies of the coagula are highly sensitive to the exposure conditions. This latex yields a highly porous foam-like structure, in which particles are strongly coalesced but form percolating patches around the pores. The same latex but under other conditions produces a coagulum of large numbers of aggregated particles with a raspberry-like morphology. Density centrifugation experiments show that the effect of solvents on different latex fractions is not uniform, and some fractions show larger density changes than others, thus evidencing a variability in their swelling ability. Copyright 2000 Academic Press.