聚丙烯酸在纳米TiO2表面吸附行为的研究

讨论了聚丙烯酸在纳米TiO₂水悬浮体系中的吸附行为.红外光谱分析和吸附实验结果表明,纳米TiO₂通过氢键吸附PAA.PAA吸附量随着浓度的升高而增大直至饱和吸附量,且分子量越大,饱和吸附量越大.pH值增大,则饱和吸附量减小.在相同条件下,表面吸附层的厚度随PAA分子量、浓度和pH值增大而增大.这是由PAA在颗粒表面构型的变化所致.吸附PAA后的纳米TiO₂的表面电荷密度和ζ电位发生变化,pHiep值向低值方向移动.表面吸附自由能的计算结果说明,PAA在纳米TiO₂表面的吸附是自发过程.     

孔结构对活性炭吸附水溶液中铅离子的影响

选取三种表面化学性质相近的活性炭(AC),通过等温吸附实验考察活性炭对水溶液中铅离子的吸附性能,利用扫描电子显微镜(SEM)观察活性炭的表面微观形貌,通过低温(77 K)液氮吸附测定活性炭的比表面积和孔容,并分别以密度泛函理论(DFT)和Barrett-Joyner-Halenda (BJH)法计算微孔和中孔的孔径分布.结果表明:选用的三种活性炭AC1、AC2、AC3在比表面积和总孔容上呈依次下降的趋势,但表面开放孔均匀分布的AC2,具有最高的饱和吸附量,孔结构类似颗粒堆积孔的AC3,具有与表面开放孔分布集中的AC1相近的饱和吸附量;通过对孔结构与吸附量的关联分析可知,在活性炭吸附铅离子的过程中, 0.4-0.6 nm的孔是有效吸附孔, 10.5-20.6 nm、20.6-55.6 nm、5.2-10.5 nm三个区间的孔则会对吸附产生阻碍作用.     

介孔碳-镍复合物对甲基橙的吸附性能研究

以三嵌段共聚物(F127)作为表面活性剂,低分子量酚醛树脂和六水合硝酸镍分别作为碳源和镍源,利用挥发诱导自组装方法制备了有序介孔碳-镍纳米复合物;采用X射线衍射仪和透射电子显微镜分析了复合物的相组成和微结构;测定了样品的氮气吸脱附特性和对甲基橙的吸附性能,采用二级动力学方程和吸附等温线对吸附结果进行了拟合.结果表明,镍纳米微粒的平均粒径约为20nm;当纳米镍的负载量为2%时,复合物样品具有很高的Brunauer-Emmett-Teller(BET)比表面积(1 610m2/g)和较大的孔容(1.29cm3/g).与此同时,复合物样品的氮气吸脱附特性与二级动力学方程拟合结果具有很好的相关性,吸附量高达324mg/g;吸附等温线拟合结果表明,样品对甲基橙的吸附过程为单分子层吸附,与Langmuir吸附等温式的相关性良好.     

NPE在有序介孔炭上的吸附行为研究

采用有序介孔硅为硬模板制备了具有不同孔径的有序介孔炭(OMCs). 氮气吸附测试表明, 有序介孔炭具有丰富的介孔表面和集中的介孔分布. 以壬基酚聚氧乙烯醚(NPE)为探针分子, 研究了大分子酚类在有序介孔炭上的吸附行为. 吸附研究表明, NPE在有序介孔炭上的吸附满足Langmuir吸附模型. 孔结构分析表明, 大于1.5 nm的孔的表面积是决定NPE吸附量的关键因素, 而有序介孔炭的最可几孔径决定吸附速率的大小. 与吸附量相比, 吸附速率更容易受环境温度的影响. 动力学研究表明, NPE在有序介孔炭上的吸附满足准二级动力学方程.     

NPE在有序介孔炭上的吸附行为研究

采用有序介孔硅为硬模板制备了具有不同孔径的有序介孔炭(OMCs). 氮气吸附测试表明, 有序介孔炭具有丰富的介孔表面和集中的介孔分布. 以壬基酚聚氧乙烯醚(NPE)为探针分子, 研究了大分子酚类在有序介孔炭上的吸附行为. 吸附研究表明, NPE在有序介孔炭上的吸附满足Langmuir吸附模型. 孔结构分析表明, 大于1.5 nm的孔的表面积是决定NPE吸附量的关键因素, 而有序介孔炭的最可几孔径决定吸附速率的大小. 与吸附量相比, 吸附速率更容易受环境温度的影响. 动力学研究表明, NPE在有序介孔炭上的吸附满足准二级动力学方程.     

用于高效去除水中孔雀石绿的三层结构磁性复合材料Fe3O4@聚丙烯酸@ZiF-8的制备

设计并合成了一种以磁性纳米粒子为核,聚合物为中间层,金属有机骨架材料为外层的三层结构磁性复合材料(Fe₃O₄@PAA@ZIF-8)。首先利用溶剂热法制备Fe₃O₄纳米粒子,然后通过蒸馏沉淀聚合法在Fe₃O₄纳米粒子表面包覆聚丙烯酸(PAA)层,最后通过原位沉积法在PAA外部包覆ZIF-8。在对Fe₃O₄@PAA@ZIF-8的组成和结构进行表征的基础上,深入研究其对孔雀石绿(MG)的吸附性能。透射电子显微镜(TEM)显示Fe₃O₄@PAA@ZIF-8具有明显的三层结构,Fe₃O₄的平均粒径为117nm,PAA层厚度约为17 nm,ZIF-8层的厚度约为14 nm。Fe₃O₄@PAA@ZIF-8对MG的吸附量随着p H的升高而增大,吸附过程符合准二阶动力学模型和Langmuir等温吸附模...     

用于高效去除水中孔雀石绿的三层结构磁性复合材料Fe3O4@聚丙烯酸@ZiF-8的制备

设计并合成了一种以磁性纳米粒子为核，聚合物为中间层，金属有机骨架材料为外层的三层结构磁性复合材料(Fe₃O₄@PAA@ZIF 8)。首先利用溶剂热法制备Fe₃O₄纳米粒子，然后通过蒸馏沉淀聚合法在Fe₃O₄纳米粒子表面包覆聚丙烯酸(PAA)层，最后通过原位沉积法在PAA外部包覆ZIF 8。在对Fe₃O₄@PAA@ZIF 8的组成和结构进行表征的基础上，深入研究其对孔雀石绿(MG)的吸附性能。透射电子显微镜(TEM)显示 Fe₃O₄@PAA@ZIF 8 具有明显的三层结构，Fe₃O₄的平均粒径为 117nm，PAA 层厚度约为 17 nm，ZIF 8层的厚度约为 14 nm。Fe₃O₄@PAA@ZIF 8对 MG 的吸附量随着 pH 的升高而增大，吸附过程符合准二阶动力学模型和 Langmuir等温吸附模型。此外，Fe₃O₄@PAA@ZIF 8还表现出良好的重复利用性能，8次循环利用后对MG(500 mg·L^-1)的最大吸附量仍可达982 mg·g^-1。     

铝离子和钛离子化学改性MCM-41介孔材料的制备及其对污水中镉离子的吸附性能(英文)

通过在MCM-41材料中引入Al 3+和Ti 4+两种诱因金属离子合成了化学改性介孔材料Al-Ti-MCM-41和Ti-Al-MCM-41;评价了两种介孔材料对污水中镉离子的吸附行为.利用氮气吸附-脱附等温线对Al-Ti-MCM-41(1∶1)样品的吸附行为进行了详细分析,考察了吸附剂投加量、Cd2+初始质量浓度和吸附温度对其吸附行为的影响.结果表明:改性Al-Ti-MCM-41(1∶1)介孔材料的最可几孔径和比孔容分别为16nm和0.04cm3/g,由BJH法计算得到的平均孔径为17.02nm;其对污水中Cd2+的吸附率达99.8%.Cd2+的吸附率随Al-Ti-MCM-41(1∶1)介孔材料投加量的增加先增加而后降低最终达到平衡,吸附容量随Cd2+初始浓度的增大而增加;吸附温度对吸附行为基本无影响.     

ZIF-8的合成、表征及正己烷吸附性能

以甲醇为溶剂,硝酸锌六水合物为锌源,2-甲基咪唑为有机配体,通过溶剂热法合成了金属有机骨架材料ZIF-8;采用X射线衍射(XRD)、氮气吸附、热重-差热分析(TG-DSC)和扫描电子显微镜(SEM)等方法对ZIF-8样品进行了表征;研究了正己烷在ZIF-8上的液相吸附动力学和动态选择性吸附性能.结果表明,合成的ZIF-8晶体具有方钠石结构,结晶度较高,孔结构主要为0.37~1.10 nm的微孔,BET比表面积为1836 m2/g,孔体积为0.65 cm~3/g.TG-DSC和高温原位XRD分析结果表明,合成的ZIF-8具有良好的热稳定性能.283~313 K时,正己烷在ZIF-8上液相吸附的扩散系数为(2.53~8.88)×10-12cm~2/s,扩散活化能为31.11 k J/mol;308 K时,ZIF-8对正己烷的动态饱和吸附量为187.3 mg/g,由吸附穿透曲线计算得出Thomas速率常数为2.17×10~(-3)m L·min~(-1)·mg~(-1).与5A分子筛相比,ZIF-8对正己烷的吸附容量高出约1倍,液相吸附表观扩散时间常数高出约70%.     

双孔道管状有序介孔炭对维生素B12的吸附缓释性能

通过纳米铸型法,以硅基介孔分子筛SBA-15为模板,糠醇为碳源,草酸作为聚合催化剂合成了具有双孔道管状有序介孔炭CMK-5.利用粉末X射线衍射(XRD)、扫描电子显微镜(SEM)和氮气物理吸附法等对其结构进行了表征.结果表明合成的CMK-5具有有序结构,比表面积和孔容积分别高达1856 m2·g-1和2.10 cm3·g-1,在3.1和5.5nm具有集中的双孔分布.由于独特的双孔道结构特点,CMK-5在120 min内快速吸附维生素B12至平衡,吸附量高达943 mg·g-1,远高于商用活性炭.CMK-5吸附维生素B12后可以直接用于缓释,动态缓释浓度维持在～9 mg·L-1,适用于维生素B12分子在人体内的缓释.     

Different Distributions of Counterions in the Surface Layer of Cationic Surfactant Solutions

We have separately determined the surface tension of pure aqueous solutions of cetyltrimethylammonium chloride and cetyltrimethylammonium bromide and their surface potentials by a Kelvin probe system. With the help of Gibbs equation, the surface excess has been determined through approximating the chemical activity of the surfactant by their dilute bulk concentration. In the following, the surface potential—surface excess isotherms were established. Those potential isotherms evidence that cetyltrimethylammonium chloride solution has a higher value compared to that of cetyltrimethylammonium bromide under equal surface excess. This phenomenon is supposed to be owed to the different distributions of chloride and bromide ions within the adsorption layer of the solutions, which can be attributed to the different properties of those two anions.     

分子自组装法制备具有可控浸润性的铜表面简

通过简单浸泡的方法在铜基底上制备出了具有微纳米复合结构的氧化铜,再利用混合硫醇溶液[含HS(CH2)9CH3和 HS(CH2)11OH]对浸泡后的表面进行修饰,通过控制溶液中HS(CH2)11OH的浓度,制备出一系列具有不同浸润性的铜表面,实现表面从超疏水到超亲水的有效调控. 研究发现,表面浸润的可控性源于表面复合结构与不同化学组成的协同作用,微纳米复合结构的存在为表面浸润性的调节提供了必要的条件.     

Surface viscoelasticity of phospholipid monolayers at the air/water interface

The surface viscoelastic properties of monolayers of two phospholipids DPPC (L--dipalmitoylphosphatidylcholine) and DMPE (L--dimyristoylphosphatidyl-ethanolamin), at the air-water interface have been investigated. Two techniques were used for the investigation. One involved use of an interfacial shear rheometer (torsion pendulum apparatus ISR1), to provide measurements of the shear viscosity _s as a function of surface pressure, and the second, a modified LB trough with an oscillating barrier to generate periodie dilation and compression so as to measure the dilational elastic modulusE as a function of surface area.Results indicate a strong dependence of _s andE upon monolayer phases. This suggests that the viscoelastic relaxation of monolayers can be understood as molecular rearrangements, domain exchange and molecular reorientations between different monolayer states.     

MgO缺陷和不规则表面的能带结构研究

用扩展休克尔紧束缚（ＥＨＴ）晶体轨道方法对ＭｇＯ表面缺陷和不规则结构进行能带计算,并对能带的结构及组成进行了讨论。计算结果表明,各种缺陷及不规则表面的表面状态与完整晶面比较,存在明显差异,前者由于其导带底部能带的变化造成导带和价带间的能隙减小。我们发现,ＭｇＯ缺陷及不规则表面吸附能力与其表面能大小及表面不同位置原子的净电荷数密切相关。缺陷模型的表面能均大于完整晶面,故缺陷有利于表面吸附     

用表面等离子共振仪进行生物分子相互作用研究的评述

表面等离子共振仪是测量生物分子问交互作用最为有效的手段之一，但多数实验数据是在不精确的实验设计下获得的，通过对用传统方法来优化试验设计、提高仪器灵敏度进行了总结，并对获得精确蛋白质相互作用动力学信息的新方法进行了讨论。     

分子自组装法制备具有可控浸润性的铜表面

通过简单浸泡的方法在铜基底上制备出了具有微纳米复合结构的氧化铜, 再利用混合硫醇溶液[含HS(CH₂)₉CH₃和 HS(CH₂)₁₁OH]对浸泡后的表面进行修饰, 通过控制溶液中HS(CH₂)₁₁OH的浓度, 制备出一系列具有不同浸润性的铜表面, 实现表面从超疏水到超亲水的有效调控. 研究发现, 表面浸润的可控性源于表面复合结构与不同化学组成的协同作用, 微纳米复合结构的存在为表面浸润性的调节提供了必要的条件.     

Investigations on the Stability of Plasma Modified Silicone Surfaces

In this work it was investigated the effect of the exposure to different plasmas on the wettability of silicone samples. We have observed that oxygen. argon, and hydrogen glow discharges are quite effective in reducing the water contact angle of such polymer. However, indifferently to efficiency of the treatment, practically all the modified surfaces recovered great part of their original hydrophobicity. We have investigated this hydrophobic recovery using surface energy measurements and theoretical simulations based on the exponential decay of the population of polar groups on the surface. According to our results such recovery can be attributed to the decrease of polar species at the interface water–polymer surface.     

First‐principles study of the (001) surface of cubic PbTiO3

We present first‐principles calculations on the (001) surfaces of cubic PbTiO₃ with PbO and TiO₂ terminations. The cleavage energy, surface energy, surface grand potential, surface relaxation and surface electronic structure have been investigated by using the projector‐augmented wave method under generalized gradient approximation (GGA). The results show that surface energy of a TiO₂‐terminated surface is a little lower than that of a PbO‐terminated one, thus allowing both terminations to coexist. The PbO‐termination is stable in O‐ and Pb‐rich environments, while on the contrary, the TiO₂‐termination is stable in O‐ and Pb‐poor conditions. In addition, the surface rumpling S of a PbO‐terminated surface is slightly larger than that of a TiO₂‐terminated one. The relaxations dominantly take place on the outermost three layers, and an oscillatory (? + ?) damping (|Δd₁₂ | > | Δd₂₃ | > | Δd₃₄|) relaxation phenomenon appears for both terminations. The band gaps of both PbO‐ and TiO₂‐terminations are slightly lower than that of the bulk. Moreover, the DOS curves of each layer show that for the TiO₂‐termination, the top of the valence band of the first and third TiO₂ layers moves toward Fermi level. Copyright © 2008 John Wiley & Sons, Ltd.     

二硫代乙二酰胺合镍在硫化镉纳米晶表面的逐层配位组装

CdS nanocrystals, which were surface modified by poly (nickel dithioxamide) [Ni(DTO)]_n, were prepared and characterized. TEM image showed that the shape and the outward aspect of the modified CdS sample were essentially the same as those of the original material and no impurities were found. The characteristic IR peaks at 1 513cm^-1 and 870 cm^-1 confirmed the success in assembling [Ni(DTO)]_n on the surface of CdS. For XPS spectra, the characteristic bands of Ni2p3/2 and Ni2p1/2 appeared at 856 eV and 877 eV indicating the nickel in Ni(Ⅱ) oxidation state. The solid state electronic spectra showed the improvement in surface energy gap, which was changed from 2.38 eV to below 1.91 eV.     

Anisotropy analysis of the surface stress in Ag stepped surfaces with the modified embedded atom method

The surface stresses in Ag stepped surfaces (910), (710), (510), (410), (310), (210), (320), (430) and (540) have been calculated by using the modified embedded atom method (MEAM). The surface stresses in the surface plane τ_xx (along the step edge) and τ_yy (normal to the step edge) have similar orders of magnitude as the surface energy. For surfaces having the (100) and (110) terraces, the change of τ_xx and τ_yy is very small and the variation of the surface energy is smooth. The stress τ_zz (normal to the surface plane) is always tensile in the unrelaxed state. The linear variation of the change in surface energy per unit change in elastic strain , and (i.e. τ_xx ? γ, τ_yy ? γ and τ_zz) with the angle α between the (hk0) and (100) planes has a turning point corresponding to the (210) surface. The anisotropic ratio in the stepped surface having the (110) terrace is larger than that having the (100) terrace, and the wider the (110) terrace or the narrower the (100) terrace, the larger the ratio τ_yy/τ_xx. Copyright © 2006 John Wiley & Sons, Ltd.