Synthesis of graft polymers with poly(isoprene) as main chain by living anionic polymerization mechanism

The graft polymers [poly(isoprene)‐graft‐poly(styrene)] (PI‐g‐PS), [poly(isoprene)‐graft‐poly(isoprene)] (PI‐g‐PI), [poly(isoprene)‐graft‐(poly(isoprene)‐block‐poly(styrene))] PI‐g‐(PI‐b‐PS), and [poly(isoprene)‐graft‐(poly(styrene)‐block‐poly(isoprene))] PI‐g‐(PS‐b‐PI) with PI as main chain were synthesized through living anionic polymerization (LAP) mechanism and the efficient coupling reaction. First, the PI was synthesized by LAP mechanism and epoxidized in H₂O₂/HCOOH system for epoxidized PI (EPI). Then, the graft polymers with controlled molecular weight of main chain and side chains, and grafting ratios were obtained by coupling reaction between PI^?Li⁺, PS^?Li⁺, PS‐b‐PI^?Li⁺, or PI‐b‐PS^?Li⁺ macroanions and the epoxide on EPI. The target polymers and all intermediates were well characterized by SEC,¹H NMR, as well as their thermal properties were also evaluated by DSC. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Electrochemical Performance of PEO10LiX-Li2TiO3 Composite Polymer Electrolytes

Introduction Recently, polymer electrolytes have attracted much attention for their potential use in replacing flammable organic solvent electrolytes currently used in lith-ium-ion batteries, thus improving the safety of re-chargeable lithium batteries. Moreover, the batteries with PE can be made in any shape, which make fully use of the space of electronic devices. PEO is a linear polymer with helix structure, and its structure makes it have much higher dissolution ability for salt even tho…     

Degradation of poly(acrylates) under SF5+ primary ion bombardment studied using time‐of‐flight secondary ion mass spectrometry. 2. Poly(n‐alkyl methacrylates)

Polyatomic primary ions offer low penetration depth and high damage removal rates in some polymers, facilitating their use in the molecular depth profiling of these polymers by secondary ion mass spectrometry (SIMS). This study is the second in a series of systematic characterizations of the effect of polymer chemistry on degradation under polyatomic primary ion bombardment. In this study, time‐of‐flight SIMS (ToF‐SIMS) was used to measure the damage of ～90 nm thick spin‐cast poly(methyl methacrylate), poly(n‐butyl methacrylate), poly(n‐octyl methacrylate) and poly(n‐dodecyl methacrylate) films under extended (～2 × 10¹⁴ ions cm^?2) 5 keV SF₅⁺ bombardment. The degradation of the poly(n‐alkyl methacrylates) were compared to determine the effect of the length of the alkyl pendant group on their degradation under SF₅⁺ bombardment. The sputter rate and stability of the characteristic secondary ion intensities of these polymers decreased linearly with alkyl pendant group length, suggesting that lengthening the n‐alkyl pendant group resulted in increased loss of the alkyl pendant groups and intra‐ or intermolecular cross‐linking under SF₅⁺ bombardment. These results are partially at variance with the literature on the thermal degradation of these polymers, which suggested that these polymers degrade primarily via depolymerization with minimal intra‐ or intermolecular cross‐linking. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis and characterization of well‐defined ABC 3‐Miktoarm star‐shaped terpolymers based on poly(styrene), poly(ethylene oxide), and poly(ϵ‐caprolactone) by combination of the “living” anionic polymerization with the ring‐opening polymerization

A series of well‐defined ABC 3‐Miktoarm star‐shaped terpolymers [Poly(styrene)‐Poly(ethylene oxide)‐Poly(ε‐caprolactone)](PS‐PEO‐PCL) with different molecular weight was synthesized by combination of the “living” anionic polymerization with the ring‐opening polymerization (ROP) using macro‐initiator strategy. Firstly, the “living” poly(styryl)lithium (PS^?Li⁺) species were capped by 1‐ethoxyethyl glycidyl ether(EEGE) quantitatively and the PS‐EEGE with an active and an ethoxyethyl‐protected hydroxyl group at the same end was obtained. Then, using PS‐EEGE and diphenylmethylpotassium (DPMK) as coinitiator, the diblock copolymers of (PS‐b‐PEO)_p with the ethoxyethyl‐protected hydroxyl group at the junction point were achieved by the ROP of EO and the subsequent termination with bromoethane. The diblock copolymers of (PS‐b‐PEO)_d with the active hydroxyl group at the junction point were recovered via the cleavage of ethoxyethyl group on (PS‐b‐PEO)_p by acidolysis and saponification successively. Finally, the copolymers (PS‐b‐PEO)_d served as the macro‐initiator for ROP of ε‐CL in the presence of tin(II)‐bis(2‐ethylhexanoate)(Sn(Oct)₂) and the star(PS‐PEO‐PCL) terpolymers were obtained. The target terpolymers and the intermediates were well characterized by ¹H‐NMR, MALDI‐TOF MS, FTIR, and SEC. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1136–1150, 2008     

Miscible blends of poly(ethylene oxide) with brush copolymers of poly(vinyl alcohol)‐graft‐poly(l‐lactide)

Even though poly(ethylene oxide) (PEO) is immiscible with both poly(l ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA), this article shows a working route to obtain miscible blends based on these polymers. The miscibility of these polymers has been analyzed using the solubility parameter approach to choose the proper ratios of the constituents of the blend. Then, PVA has been grafted with l ‐lactide (LLA) through ring‐opening polymerization to obtain a poly(vinyl alcohol)‐graft‐poly(l ‐lactide) (PVA‐g‐PLLA) brush copolymer with 82 mol % LLA according to ¹H and ¹³C NMR spectroscopies. PEO has been blended with the PVA‐g‐PLLA brush copolymer and the miscibility of the system has been analyzed by DSC, FTIR, OM, and SEM. The particular architecture of the blends results in DSC traces lacking clearly distinguishable glass transitions that have been explained considering self‐concentration effects (Lodge and McLeish) and the associated concentration fluctuations. Fortunately, the FTIR analysis is conclusive regarding the miscibility and the specific interactions in these systems. Melting point depression analysis suggests that interactions of intermediate strength and PLOM and SEM reveal homogeneous morphologies for the PEO/PVA‐g‐PLLA blends. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1217–1226     

A novel tridentate nitrogen donor as ligand in copper catalyzed ATRP of methyl methacrylate

A tridentate ligand, BPIEP: 2,6‐bis[1‐(2,6‐diisopropyl phenylimino) ethyl] pyridine, having central pyridine unit and two peripheral imine coordination sites was effectively employed in controlled/“living” radical polymerization of MMA at 90°C in toluene as solvent, Cu^IBr as catalyst, and ethyl‐2‐bromoisobutyrate (EBiB) as initiator resulting in well‐defined polymers with polydispersities M_w/M_n ≤ 1.23. The rate of polymerization follows first‐order kinetics, k_app = 3.4 × 10^?5 s^?1, indicating the presence of low radical concentration ([P*] ≤ 10^?8) throughout the reaction. The polymerization rate attains a maximum at a ligand‐to‐metal ratio of 2:1 in toluene at 90°C. The solvent concentration (v/v, with respect to monomer) has a significant effect on the polymerization kinetics. The polymerization is faster in polar solvents like, diphenylether, and anisole, as compared to toluene. Increasing the monomer concentration in toluene resulted in a better control of polymerization. The molecular weights (M_n,SEC) increased linearly with conversion and were found to be higher than predicted molecular (M_n,Cal). However, the polydispersity remained narrow, i.e., ≤1.23. The initiator efficiency at lower monomer concentration approaches a value of 0.7 in 110 min as compared to 0.5 in 330 min at higher monomer concentration. The aging of the copper salt complexed with BPIEP had a beneficial effect and resulted in polymers with narrow polydispersitities and higher conversion. PMMA obtained at room temperature in toluene (33%, v/v) gave PDI of 1.22 (M_n = 8500) in 48 h whereas, at 50°C the PDI is 1.18 (M_n = 10,300), which is achieved in 23 h. The plot of lnk_app versus 1/T gave an apparent activation energy of polymerization as (ΔE^≠_app) 58.29 KJ/mol and enthalpy of equilibrium (ΔH⁰_eq) to 28.8 KJ/mol. Reverse ATRP of MMA was successfully performed using AIBN in bulk as well as solution. The controlled nature of the polymerization reaction was established through kinetic studies and chain extension experiments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4996–5008, 2005     

Synthesis of a water‐soluble diblock copolymer of polysulfonic diphenyl aniline and poly(ethylene oxide)

We report the synthesis of a water‐soluble diblock copolymer composed of polysulfonic diphenyl aniline (PSDA) and poly(ethylene oxide) (PEO), which was prepared by reacting an amine‐terminated PSDA and tosylate PEO (PEO‐Tos). First, a HCl‐mediated polymerization of sulfonic diphenyl aniline monomer with the formation of HCl‐doped PSDA was carried out. After its neutralization and reduction, a secondary amine‐functionalized PSDA was obtained. Second, PEO‐Tos was synthesized via the tosylation of the monohydroxyl PEO methyl ether with tosylol chloride. Diblock copolymers with various PEO segment lengths (PSDA‐b‐PEO‐350 and PSDA‐b‐PEO‐2000) were obtained with PEO‐350 [number‐average molecular weight (M_n) = 350] and PEO‐2000 (M_n = 2000). The prepolymers and diblock copolymers were characterized by Fourier transform infrared spectroscopy, NMR, mass spectrometry, and ultraviolet–visible light. They had relatively low conductivities, ranging from 10^?6 to 10^?3 S/cm, because of the withdrawing effect of the sulfonic group as well as the steric effects of the bulky aromatic substitutuents at the N sites of the polyaniline backbone and of the PEO block. These polymers were self‐doped, and an intermolecular self‐doping was suggested. The external doping was, however, more effective. The self‐doping induced aggregation in water among the PSDA backbones, which was also stimulated by the presence of hydrophilic PEO blocks. Furthermore, the electrical conductivities of the diblock copolymers were strongly temperature‐dependent. PSDA‐b‐PEO‐2000 exhibited about one order of magnitude increase in conductivity upon heating from 32 to 57 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2179–2191, 2004     

Ab initio quantum chemistry and molecular dynamics simulations studies of LiPF6/poly(ethylene oxide) interactions

Ab initio and molecular mechanics studies of LiPF₆ and the interaction of the salt with the poly(ethylene oxide) (PEO) oligomer dimethylether have been performed. Optimized geometries and energies of Li⁺/PF₆^? complexes obtained from quantum chemistry revealed a preference for C_3V symmetry structures for Li⁺–P separations under 2.8 Å, C_2V symmetry for Li⁺–P in the range of 2.8–3.3 Å and C_4V symmetry for Li⁺–P separations larger than 3.3 Å. Electron correlation effects were found to make an insignificant contribution to binding in the Li⁺/PF₆^? complex. By contrast, analogous studies of PF₆^?/PF₆^? and PF₆^?/dimethyl ether complexes revealed important contributions of electron correlation to the complex interaction energy. A molecular mechanics force field for simulations of PEO/LiPF₆ melts was parameterized to reproduce the geometries and energies of Li⁺/PF₆^?, PF₆^?/PF₆^?, PF₆^?/dimethylether complexes. Molecular dynamics simulations of PEO/LiPF₆ melts were performed to validate this quantum chemistry‐based force field. Accurate reproduction of the increase in solution density with addition of salt was found while the electrical conductivity of PEO/LiPF₆ solutions was found to be within an order of magnitude of the experimental values. © 2001 John Wiley & Sons, Inc. J Comput Chem 22: 641–654, 2001     

Degradation of poly(acrylates) under SF5+ primary ion bombardment studied using time‐of‐flight secondary ion mass spectrometry. 3. Poly(hydroxyethyl methacrylate) with chemical derivatization

Molecular depth profiling of polymers by secondary ion mass spectrometry (SIMS) has focused on the use of polyatomic primary ions due to their low penetration depth and high damage removal rates in some polymers. This study is the third in a series of systematic characterizations of the effect of polymer chemistry on degradation under polyatomic primary ion bombardment. In this study, time‐of‐flight SIMS (ToF‐SIMS) was used to assess 5 keV SF₅⁺‐induced damage of ～90 nm thick spin‐cast poly(2‐hydroxyethyl methacrylate) (PHEMA) and ～130 nm thick trifluoroacetic anhydride‐derivatized PHEMA (TFAA‐PHEMA) films. The degradation of these polymers under extended SF₅⁺ bombardment (～2 × 10¹⁴ ions cm^?2) was compared to determine the effect of the pendant group chemistry on their degradation. The sputter rate and ion‐induced damage accumulation rate of PHEMA were similar to a poly(n‐alkyl methacrylate) of similar pendant group length, suggesting that the addition of a terminal hydroxyl group to the alkyl pendant group does not markedly change the stability of poly(n‐alkyl methacrylates) under SF₅⁺ bombardment. The sputter rate and ion‐induced damage accumulation rate of TFAA‐PHEMA were much higher than a poly(n‐alkyl methacrylate) of similar pendant group length, suggesting that derivatization of the terminal hydroxyl group can significantly reduce degradation of the polymer under SF₅⁺ bombardment. This result is in good agreement with the literature on the thermal and radiation‐induced degradation of fluorinated poly(alkyl methacrylates), which suggests that the electron‐withdrawing fluorinated pendant group increases the probability of depolymerization. Copyright © 2004 John Wiley & Sons, Ltd.     

Single Lithium‐Ion Conducting Polymer Electrolytes Based on a Super‐Delocalized Polyanion

A novel single lithium‐ion (Li‐ion) conducting polymer electrolyte is presented that is composed of the lithium salt of a polyanion, poly[(4‐styrenesulfonyl)(trifluoromethyl(S‐trifluoromethylsulfonylimino)sulfonyl)imide] (PSsTFSI^?), and high‐molecular‐weight poly(ethylene oxide) (PEO). The neat LiPSsTFSI ionomer displays a low glass‐transition temperature (44.3 °C; that is, strongly plasticizing effect). The complex of LiPSsTFSI/PEO exhibits a high Li‐ion transference number (t_Li⁺=0.91) and is thermally stable up to 300 °C. Meanwhile, it exhibits a Li‐ion conductivity as high as 1.35×10^?4 S cm^?1 at 90 °C, which is comparable to that for the classic ambipolar LiTFSI/PEO SPEs at the same temperature. These outstanding properties of the LiPSsTFSI/PEO blended polymer electrolyte would make it promising as solid polymer electrolytes for Li batteries.     

Li1.3Al0.3Ti1.7(PO4)3 filler effect on (PEO)LiClO4 solid polymer electrolyte

Composite polymer electrolyte (CPE) films consisting of PEO, LiClO₄, and Li_1.3Al_0.3Ti_1.7(PO₄)₃ with fixed EO/Li = 8 but different relative compositions of the two lithium salts were prepared by the solution casting method. The CPE films were characterized using SEM, DSC, electrical impedance spectroscopy (EIS), and ion transference number measurement. It was found that the incorporation of LiClO₄ and Li_1.3Al_0.3Ti_1.7(PO₄)₃ into PEO by keeping EO/Li = 8 reduced the crystallinity of PEO from 50.34% to the range of 3.57–15.63% depending upon the relative composition of the two salts. The room temperature impedance spectra of the CPE films all exhibited a shape of depressed semicircle in the high frequency range and inclined line in the low frequency range, but the high temperature ones were mainly inclined lines. The Li⁺ ionic conductivity of the CPE films mildly increased and then decreased with increasing Li_1.3Al_0.3Ti_1.7(PO₄)₃ content, and the maximum conductivities were obtained at Li_1.3Al_0.3Ti_1.7(PO₄)₃ content of 15 wt % for all measuring temperatures, for example, 1.378 × 10^?3 S/cm at 100 °C and 1.387 × 10^?5 S/cm at 25 °C. The temperature dependence of the ionic conductivity of the CPE films follows the Vogel–Tamman–Fulcher (VTF) equation The pseudo activation energies (E_a) were rather low, 0.053–0.062 eV, indicating an easy migration of Li⁺ in the amorphous phase dominant PEO. The pre‐exponent constant A and ion transference number t_Li+ were found to have a similar variation tendency with increasing Li_1.3Al_0.3Ti_1.7(PO₄)₃ content and reached their maximums also at Li_1.3Al_0.3Ti_1.7(PO₄)₃ content of 15 wt %. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 743–751, 2005     

Synthesis and self‐assembly morphologies of amphiphilic multiblock copolymers [poly(ethylene oxide)‐b‐polystyrene]n via trithiocarbonate‐embedded PEO macro‐RAFT agent

An amphiphilic multiblock copolymer [poly(ethylene oxide)‐b‐polystyrene]_n [(PEO‐b‐PS)_n] is synthesized by using trithiocarbonate‐embedded PEO as macro‐RAFT agent. PEO with four inserted trithiocarbonate (M_n = 9200 and M_w/M_n = 1.62) groups is prepared first by condensation of α, ω‐dihydroxyl poly(ethylene oxide) with S, S′‐Bis(α, α′‐dimethyl‐α″‐acetic acid)‐trithiocarbonate (BDATC) in the presence of pyridine, then a series of goal copolymers with different St units (varied from 25 to 218 per segment) are obtained by reversible addition‐fragmentation chain transfer (RAFT) polymerization. The synthesis process is monitored by size exclusion chromatography (SEC), ¹H NMR and FT‐IR. The self‐assembled morphologies of the copolymers are strongly dependent of the length of PS block chains when the chain length of PEO is fixed, some new morphologies as large leaf‐like aggregates (LLAs), large octopus‐like aggregates (LOAs), and coarse‐grain like micelles (CGMs) are observed besides some familiar aggregates as large compound vesicles (LCVs), lamellae and rods, and the effect of water content on the morphologies is also discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6071–6082, 2006     

High capacity and cycling stability of poly(diaminoanthraquinone) as an organic cathode for rechargeable lithium batteries

Poly(1,5‐diaminoanthraquinone) is synthesized by oxidative polymerization of diaminoanthraquinone monomers and investigated as an organic host for Li‐storage reaction. Benefiting from its high density of redox‐active, Li⁺‐associable benzoquinone groups attached to conducting polyaniline backbones, this polymer undergoes its cathodic reaction predominately through Li⁺‐insertion/extraction processes, delivering a very high reversible capacity of 285 mAh g^?1. In addition, the PDAQ polymer cathode exhibits an excellent rate capability (125 mAh g^?1 at 800 mA g^?1) and a considerable cyclability with a capacity retention of ～160 mAh g^?1 over 200 cycles, possibly serving as a sustainable, high capacity Li⁺ host cathode for Li‐ion batteries. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 235–238     

Mechanism of Dissolution of a Lithium Salt in an Electrolytic Solvent in a Lithium Ion Secondary Battery: A Direct Ab Initio Molecular Dynamics (AIMD) Study

The mechanism of dissolution of the Li⁺ ion in an electrolytic solvent is investigated by the direct ab initio molecular dynamics (AIMD) method. Lithium fluoroborate (Li⁺BF₄^?) and ethylene carbonate (EC) are examined as the origin of the Li⁺ ion and the solvent molecule, respectively. This salt is widely utilized as the electrolyte in the lithium ion secondary battery. The binding of EC to the Li⁺ moiety of the Li⁺BF₄^? salt is exothermic, and the binding energies at the CAM–B3LYP/6‐311++G(d,p) level for n=1, 2, 3, and 4, where n is the number of EC molecules binding to the Li⁺ ion, (EC)_n(Li⁺BF₄^?), are calculated to be 91.5, 89.8, 87.2, and 84.0 kcal mol^?1 (per EC molecule), respectively. The intermolecular distances between Li⁺ and the F atom of BF₄^? are elongated: 1.773 Å (n=0), 1.820 Å (n=1), 1.974 Å (n=2), 1.942 Å (n=3), and 4.156 Å (n=4). The atomic bond populations between Li⁺ and the F atom for n=0, 1, 2, 3, and 4 are 0.202, 0.186, 0.150, 0.038, and 0.0, respectively. These results indicate that the interaction of Li⁺ with BF₄^? becomes weaker as the number of EC molecules is increased. The direct AIMD calculation for n=4 shows that EC reacts spontaneously with (EC)₃(Li⁺BF₄^?) and the Li⁺ ion is stripped from the salt. The following substitution reaction takes place: EC+(EC)₃(Li⁺BF₄^?)→(EC)₄Li⁺?(BF₄^?). The reaction mechanism is discussed on the basis of the theoretical results.     

Comparison of Li+‐ion conductivity in linear and crosslinked poly(ethylene oxide)

Polymer electrolytes are of tremendous importance for applications in modern lithium‐ion (Li⁺‐ion) batteries due to their satisfactory ion conductivity, low toxicity, reduced flammability, as well as good mechanical and thermal stability. In this study, the Li⁺‐ion conductivity of well‐defined poly(ethylene oxide) (PEO) networks synthesized via copper(I)‐catalyzed azide–alkyne cycloaddition is investigated by electrochemical impedance spectroscopy after addition of different lithium salts. The ion conductivity of the network electrolytes increases with increasing molar mass of the PEO chains between the junction points which is completely opposite to the behavior of their respective uncrosslinked linear precursors. Obviously, this effect is directly related to the segmental mobility of the PEO chains. Furthermore, the ion conductivity of the network electrolytes under investigation increases also with increasing size of the anion of the added lithium salt due to a weaker anti‐plasticizing effect of the more bulky anions. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 21–28     

Design of alkaline metal ion conducting polymer electrolytes

Polysiloxanes with covalently attached oligo ethylene oxide and di-t-butylphenol ( I ), naphthol ( II ), and hexafluoropropanol ( III ) were synthesized. The crosslinked polymers with a hexamethylene spacer were also prepared. The ion conductivities of the Li, Na, and K salts were measured as a function of temperature. The highest conductivities for K and Na of I at 30°C were 5.5 × 10^?5 and 5.0 × 10^?5 S/cm, respectively, when the ratio of the ion to ethylene oxide unit was 0.014. On the other hand, Li conductivity was 8.0 × 10^?6 S/cm when the ratio between Li and ethylene oxide unit was 0.019. The maximum conductivities of Li ions of II and III were in the order of 10^?6 and 10^?7 S/cm at 30°C, respectively. When the polymers were crosslinked by a hexamethylene residue, the ion conductivities decreased while the degree of crosslinking increased. The temperature dependence of the cation conductivities of these systems could be described by the Williams-Landel-Ferry (WLF) and the Vogel-Tammann-Fulcher (VTF) equation. The results demonstrate that ion movement in these polymers is correlated with the polymer segmental motion. The order of ionic conductivity was K⁺ > Na⁺ ? Li⁺. This suggests that steric hindrance and π-electron delocalization of the anions attached to polymer backbone have a large effect on ion-pair separation and their ionic conductivities. Thermogravimetric analysis of the polymers indicated that the degradation temperature for I and II were about 100°C higher than for poly(siloxane-g-ethylene oxide). This is due to the antioxidant properties of sterically hindered phenols and naphthols. © 1993 John Wiley & Sons, Inc.     

Effect of chain architecture on the phase transition of star and cyclic poly(N‐isopropylacrylamide) in water

The heat‐induced phase transition of aqueous solutions of Poly(N‐isopropylacrylamide) (PNIPAM) in water is examined for a four‐arm PNIPAM star (s‐PNIPAM), a cyclic PNIPAM (c‐PNIPAM), and their linear counterparts (l‐PNIPAM) in the case of polymers (1.0 g L^?1) of 12,700 g mol^?1 < M_n < 14,700 g mol^?1. Investigations by turbidity, high‐sensitivity differential scanning calorimetry (HS‐DSC), and light scattering (LS) indicate that the polymer architecture has a strong effect on the cloud point (T_c: decrease for s‐PNIPAM; increase for c‐PNIPAM), the phase transition enthalpy change (ΔH decrease for s‐PNIPAM and c‐PNIPAM), and the hydrodynamic radius of the aggregates formed above T_c (R_H: c‐PNIPAM < s‐PNIPAM < l‐PNIPAM). The properties of s‐PNIPAM are compared with those of previously reported PNIPAM star polymers (3 to 52 arms). The overall observations are described in terms of the arm molecular weight and the local chain density in the vicinity of the core of the star, by analogy with the model developed for PNIPAM brushes on nanoparticles or planar surfaces. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2059–2068.     

Fluorine‐containing vinyl ether polymers: Living cationic polymerization in fluorinated solvents as new media and unique solubility characteristics in organic solvents

Living cationic polymerization of fluorine‐containing vinyl ethers [CH₂?CH? O? C₂H₄? O? C₃H₆? C_nF_2n+1: 5FVE (n = 2), 13FVE (n = 6)] was investigated in various solvents with a CH₃CH(OiBu)OCOCH₃/Et_1.5AlCl_1.5 initiating system in the presence of an added base. 5FVE was polymerized quantitatively in toluene at 0 °C, and the obtained polymers had predetermined molecular weights with narrow molecular weight distributions (M_w/M_n < 1.1). On the other hand, for the polymerization of 13FVE, the product polymers precipitated due to their extremely poor solubility in nonfluorinated organic solvents. Therefore, fluorinated solvents such as hydrochlorofluorocarbons, hydrofluorocarbons, hydrofluoroethers, or α,α,α‐trifluorotoluene, as‐yet uninvestigated for cationic polymerization, were employed. In these solvents, living polymerization was achieved even with 13FVE, yielding well‐defined polymers (M_w/M_n < 1.1, by size exclusion chromatography using a fluorinated solvent as an eluent). The solvents were also shown to be good for living polymerization of isobutyl vinyl ether. The obtained fluorine‐containing polymers underwent temperature‐responsive solubility transitions in organic solvents. Poly(5FVE) showed sensitive upper critical solution temperature (UCST)‐type phase separation behavior in toluene. Copolymers of 13FVE and isobutyl vinyl ether showed UCST‐type phase separation in common organic solvents with different polarities depending on their composition, while a homopolymer of 13FVE was insoluble in all nonfluorinated organic solvents. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of sugar‐based macromolecules via sono‐ATRP in miniemulsion

Ultrasound‐mediated atom transfer radical polymerization (sono‐ATRP) in miniemulsion media is used for the first time for the preparation of complex macromolecular architectures by a facile two‐step synthetic route. Initially, esterification reaction of sucrose or lactulose with α‐bromoisobutyryl bromide (BriBBr) is conducted to receive multifunctional ATRP macroinitiators with 8 initiation sites, followed by polymerization of n‐butyl acrylate (BA) forming arms of the star‐like polymers. The brominated lactulose‐based molecule was examined as an ATRP initiator by determining the activation rate constant (k_a) of the catalytic process in the presence of a copper(II) bromide/tris(2‐pyridylmethyl)amine (Cu^IIBr₂/TPMA) catalyst in both organic solvent and for the first time in miniemulsion media, resulting in k_a = (1.03 ± 0.01) × 10⁴ M^?1 s^?1 and k_a = (1.16 ± 0.56) × 10³ M^?1 s^?1, respectively. Star‐like macromolecules with a sucrose or lactulose core and poly(n‐butyl acrylate) (PBA) arms were successfully received using different catalyst concentration. Linear kinetics and a well‐defined structure of synthesized polymers reflected by narrow molecular weight distribution (M_w/M_n = 1.46) indicated 105 ppm wt of catalyst loading as concentration to maintain controlled manner of polymerization process. ¹H NMR analysis confirms the formation of new sugar‐inspired star‐shaped polymers.     

Polyphosphonates as ionic conducting polymers

Polyphosphonates, a class of polymers with the generic formula –[P(R)(X)–OR'O]_n–, exhibit a high degree of modularity due to the range of R, R', and X groups that can be incorporated. As such, these polymers may be designed with a polyethylene oxide (PEO) backbone (R' group) and employed as solid polymer electrolytes (SPEs). Two PEO-containing polyphosphonate analogs (R = Ph; X = S or Se) were doped with LiPF₆ and their conductivities were measured. Conductivities were similar (X = S) to or exceeding (X = Se) those of standard PEO systems (just below 10⁻⁴ S/cm at 100°C). Binding models for Li⁺ were generated using ³¹P{¹H}NMR titration experiments. Binding of Li⁺ by these polyphosphonates followed a positive cooperativity model, and varying the X group (S or Se) affected the observed cooperativity (Hill coefficient = 1.73 and 4.16, respectively). The presence of Se also leads to an increase in conductivity as temperature is raised above the T_g, which is likely an effect of reduced Columbic interactions. Because of their modularity and ease with which cation binding can be evaluated using ³¹P{¹H} NMR titration experiments, polyphosphonates offer a unique approach for the modification of Li⁺ ion battery technology.