双槽法电沉积Cu/Ni多层纳米线有序阵列

以多孔阳极氧化铝（AAO）为模板，采用双槽法电沉积工艺制得高度有序的Cu/Ni多层纳米线阵列。利用扫描电镜（SEM）和透射电镜（TEM）对Cu/Ni多层纳米线进行了表征，观察到纳米线表面平滑，多层结构清晰，各子层厚度均匀，直径约为 100 nm，与AAO模板孔径基本一致。由选区电子衍射（SAED）照片可知，多层纳米线中Cu层和Ni层均为单晶结构。振动样品磁强计（VSM）测试结果表明，Cu/Ni多层纳米线阵列具有明显的垂直磁各向异性，外加磁场垂直和平行于AAO模板表面时，磁滞回线的矩形比分别为 0.701 和 0.101 ，矫顽力分别为 589 Oe和 202 Oe。通过控制铝阳极氧化工艺及电沉积时间，可获得不同直径、不同子层厚度的Cu/Ni多层纳米线阵列。     

Large-area highly-oriented SiC nanowire arrays: synthesis, Raman, and photoluminescence properties

Large-area highly oriented SiC nanowire arrays have been fabricated by chemical vapor reaction using an ordered nanoporous anodic aluminum oxide (AAO) template and a graphite reaction cell. Their microstructures were characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction and high-resolution transmission electron microscopy. The results show that the nanowires are single-crystalline beta-SiC's with diameters of about 30-60 nm and lengths of about 8 microm, which are parallel to each other, uniformly distributed, highly oriented, and in agreement with the nanopore diameter of the applied AAO template. The nanowire axes lie along the [111] direction and possess a high density of planar defects. Some unique optical properties are found in the Raman spectroscopy and photoluminescence emission from oriented SiC nanowire arrays, which are different from previous observations of SiC materials. The growth mechanism of oriented SiC nanowire arrays is also analyzed and discussed.     

Sb有序单晶纳米线阵列的制备

采用直流电沉积的方法在氧化铝模板（AAM）中成功地制备了Sb单晶纳米线阵列. X射线衍射（XRD）证明所制得的纳米线阵列为(110)取向的六方相Sb.透射电镜（TEM）显示Sb纳米线平滑而均匀,直径40～50 nm,长径比大于1000.选区电子衍射（SAED）结果表明,所制得的纳米丝为Sb单晶丝.场发射扫描电镜（FE-SEM）显示Sb纳米线阵列规则,填充率接近100％.     

InSb纳米线阵列的可控制备与光谱表征

采用脉冲电沉积结合阳极氧化铝模板技术制备了不同生长方向的闪锌矿型InSb纳米线阵列. 结果表明, 控制电解液中十二烷基硫酸钠(SDS)的浓度, 可使纳米线的择优生长方向从[400]向[220]方向转变. 利用X射线衍射仪、 场发射扫描电子显微镜、 高分辨透射电子显微镜对所制备纳米线的相组成和微结构进行了表征. 激光拉曼光谱结果表明, 不同生长方向的InSb纳米线阵列的拉曼光谱有明显差异. 与体材料相比, InSb纳米线阵列的红外吸收声子散射峰发生强烈红移, 其吸收带边发生了明显蓝移.     

铅纳米线阵列的制备

使用电化学沉积方法,在有序的氧化铝模板(AAO)孔洞中制备了铅纳米线有序阵列。用X射线衍射仪(XRD)、场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)对样品的结构、形貌、进行表征和观测。XRD的结果表明所制备的样品为纯的立方面心铅,且纳米线生长沿<220>有很好的取向。FE-SEM的图片清晰地说明铅纳米线阵列是大面积、高填充率和高度有序的。TEM的结果显示纳米线直径均匀、表面光滑且长径比大。     

Co、Ni及其合金纳米线阵列的制备及磁性研究

采用交流电化学沉积法,在多孔阳极氧化铝(AAO）模板孔洞中成功组装了铁磁性金属Co、Ni、CoNi合金纳米线阵列并采用扫描电子显微镜(SEM）、X射线衍射(XRD）等对样品进行表征。结果表明,Co、Ni及CoNi合金阵列体系中纳米线均匀有序,形状各向异性较大(长径比达30以上）,有显著的结晶择优取向。对Co、Ni、CoNi合金纳米线阵列体系进行磁性分析,振动样品磁强计(VSM）测试结果显示,纳米线有明显的磁各向异性,适合用作垂直磁记录介质。纳米线阵列退火后沿纳米线方向矫顽力和矩形比减小,样品的垂直磁各向异     

Size-dependent orientation growth of large-area ordered Ni nanowire arrays

Large-area ordered Ni nanowire arrays with different diameters have been fabricated by the direct current electrodeposition into the holes of porous anodic alumina membrane. The crystal structure and micrograph of nanowire arrays are characterized by X-ray diffraction, field-emission scanning electron microscopy and high-resolution transmission electron microscopy. The results indicate that the growth orientation of Ni nanowires turns from [110] to [111] direction with increasing diameters of nanowires. The mechanism of the growth was discussed in terms of interface energy minimum principle. The size-dependent orientation of Ni nanowire arrays has the important significance for the design and control of nanostructures.     

大面积Bi单晶纳米线阵列的制备

在有序的氧化铝模板(AAO)的孔洞中, 采用电化学沉积工艺成功地制备了准金属Bi纳米线有序阵列. 使用X射线衍射仪(XRD)、场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)及高分辨电子显微镜(HRTEM)对样品的结构和形貌进行了表征. XRD结果表明, 所制备的铋样品为六方相, 且沿[110]方向有很好的生长取向; FE-SEM图片清晰地说明铋纳米线阵列是大面积、填充率高和高度有序的; TEM的结果显示纳米线直径均匀、表面光滑且长径比大; HRTEM图片中清晰的晶格条纹和选区电子衍射(SAED)结果表明纳米线是单晶.     

Ordered nickel oxide nanowire arrays and their optical absorption properties

Ordered NiO nanowire arrays embedded in anodic alumina membranes have been prepared by using an electrochemical deposition method. After annealing at 300 °C, the NiO nanowire arrays were characterized using SEM, TEM, SAED, and XRD. SEM and TEM observations reveal that these nanowires are dense, continuous and arranged roughly parallel to one another. XRD and SAED analysis together indicate that these NiO nanowires crystallize with a polycrystalline structure. The optical absorption band gap of NiO nanowire arrays is 3.74 eV, and no obvious blue shift or red shift with respect of that of the bulk NiO can be observed.     

One-dimensional Intrinsic Ferromagnetic Semiconductor CuCl_2: a First-principles Study

One-dimensional nanowires with robust magnetism are desirable for spintronic applications. Herein, on the basis of the first-principles calculations, systematic investigations on the electronic and magnetic properties of the CuCl2 nanowire were performed, which can be potentially tailored from its bulk form. The CuCl2 nanowire exhibits a ferromagnetic ground state. The band structures indicate that the CuCl2 nanowire is a ferromagnetic semiconductor. The spin flip gap is large enough for avoiding spin flip. Phonon dispersion and Born-Oppenheimer molecular dynamics simulation manifest that the CuCl2 nanowire is stable. In addition, distinct magnetic properties of the CuCl2 nanowires inside two types of carbon nanotubes were obtained. The study broadens the family of the existing one-dimensional materials with promising applications for spintronics.     

有序CdS纳米线阵列的制备和光学特性

应用直流电沉积法在多孔氧化铝模板中制备了高度有序的CdS纳米线阵列,并由XRD、Raman、SEM、TEM和HRTEM等进行物理化学表征.结果表明,沉积在多孔氧化铝模板中的CdS呈六角结构,c轴沿孔长度方向定向生长.紫外吸收光谱研究表明,随着纳米线尺寸的减小,纳米线阵列的吸收边向短波长方向移动,荧光光谱测量显示,CdS纳米线阵列的荧光强度高于氧化铝模板,而且在可见光区的荧光特性与激发波长无关.     

Fe-Co-Ni合金纳米线有序阵列的模板合成与磁性

以二次阳极氧化的氧化铝膜为模板，用电化学沉积的方法成功地合成了Fe-Co-Ni三组份有序纳米线阵列.扫描电子显微镜（SEM）和透射电子显微镜(TEM)观察表明纳米线表面光滑、有序、高长径比；磁性测量表明,其矫顽力较同组份的膜材料有较大的提高.将样品在惰性气体氛围中不同温度下退火，随着退火温度增加，其纵向矫顽力有一个极值，而对应的横向矫顽力没有类似的变化，关于这一现象的机理,本文进行了初步的讨论. 图5参15     

Effective deposition potential induced size-dependent orientation growth of Bi-Sb alloy nanowire arrays

The influence of effective deposition potential on the orientation and diameter of Bi(1-x)Sbx alloy nanowire arrays by pulsed electrodeposition technique was reported. X-ray diffraction, field-emission scanning electron microscopy, and transmission electron microscopy analysis show that the orientation of the Bi(1-x)Sbx nanowires can be turned from the [110] to the [202] direction by increasing the effective deposition potential, and the nanowires fully fill in the pores of the AAM in the lower potential region, while in the higher potential region the nanowires partly fill the pores of the AAM. The origin of those phenomena and the growth mechanism of the nanowire are discussed together with composition analysis.     

一种新的电化学方法制备CdS纳米线阵列

用一种新的电化学方法在多孔氧化铝模板中制备了CdS纳米线阵列体系,并用XRD、TEM对样品进行表征,结果显示CdS纳米线为立方相和六方相的多晶混合结构,对沉积机理进行了讨论.荧光光谱测量显示CdS纳米线阵列体系有三个强的紫外发光带和一个黄绿发光带.该文所使用的方法可以用来在氧化铝模板中制备其它材料的纳米线阵列体系.     

Epitaxial Growth and Thermoelectric Measurement of Bi2Te3/Sb Superlattice Nanowires

Superlattice nanowires are expected to show further enhanced thermoelectric performance compared with conventional nanowires or superlattice thin films. We report the epitaxial growth of high density Bi₂Te₃/Sb superlattice nanowire arrays with a very small bilayer thickness by pulse electrodeposition. Transmission electron microscopy, selected area electron diffraction and high resolution transmission electron microscopy were used to characterize the superlattice nanowires, and Harman technique was employed to measure the figure of merit (ZT) of the superlattice nanowire array in high vacuum condition. The superlattice nanowire arrays exhibit a ZT of 0.15 at 330 K, and a temperature difference of about 6.6 K can be realized across the nanowire arrays.     

非晶Co-Pt合金纳米线有序阵列的制备及其磁学性质

通过直流电沉积方法，以多孔阳极氧化铝(AAO)为模板，在室温下成功制备出一维非晶态Co-Pt合金纳米线有序阵列. SEM和TEM分析表明：纳米线长度均约10 μm，直径35 nm；纳米线在阳极氧化铝模板孔内互相平行. XRD结果表明，制备的纳米线为非晶态结构，经过700 ℃退火处理后则转变为面心立方(FCC)多晶结构. 采用VSM(振动样品磁强计)对退火处理前后样品的矫顽力和剩磁比进行研究，结果表明：当外加磁场与纳米线平行时，非晶态Co-Pt合金纳米线的矫顽力高达1700 Oe，剩磁比为0.83，表现出明显的垂直磁各向异性；而退火处理则使其优秀的磁学性质消失. 退火前后不同的磁学性质源于其不同的微观结构. 非晶态的Co-Pt合金纳米线由于无磁晶各向异性竞争，进而使得由纳米线一维形态引起的形状各向异性起主导作用，使其显示了很好的垂直磁各向异性；而多晶样品由于磁晶各向异性与形状各向异性竞争，导致矫顽力和剩磁比迅速降低.     

Fabrication and characterization of single-crystalline ZnTe nanowire arrays

Semiconductor ZnTe nanowire arrays have been synthesized by the pulsed electrochemical deposition from aqueous solutions into porous anodic alumina membranes. X-ray diffraction analyses show that the as-synthesized nanowires have a highly preferential orientation. Scanning electron microscopy, transmission electron microscopy, and high-resolution transmission electron microscopy indicate that high-filling, ordered, and single-crystalline nanowire arrays have been obtained. The optical absorption spectra of the nanowire arrays show that the optical absorption band edge of the ZnTe nanowire array exhibits a blue shift compared with that of bulk ZnTe. The growth mechanism and the electrochemical deposition process are discussed together with the chemical compositions analysis.     

单晶Ni纳米线阵列的制备与磁性能

采用恒电流沉积方法, 在多孔阳极氧化铝(AAO)模板中制备出了具有单晶结构的Ni纳米线阵列. 采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射(XRD)技术对制备的Ni纳米线阵列的形貌及结构进行了表征. 利用振动样品磁强计(VSM)对单晶Ni纳米线阵列的磁性能进行了研究. 结果表明, 单晶镍纳米线阵列的易磁化方向为纳米线轴向, 并且与多晶纳米线相比显示出了更高的矫顽力. 直径为30 nm的纳米线具有较高的矫顽力(8.236×104 A/m)和较高的剩磁比(Mr＝0.94Ms).     

金纳米线阵列制备及其光谱特性

利用电化学沉积方法在重离子径迹模板中制备出直径从45 nm到200 nm, 长径比达700的金纳米线阵列, 利用扫描电子显微镜(SEM)和X射线衍射(XRD)对所制备金纳米线的形貌及晶体结构进行分析, 结果表明, 在1.5 V(无参比电极)沉积电压下所制备出的直径为200 nm金纳米线沿[100]晶向具有较好择优取向. 利用紫外-可见光谱(UV-Vis)对镶嵌在透明模板中平行排列的金纳米线阵列光学特性进行研究, 发现金纳米线直径为45 nm时, 其紫外可见光谱在539 nm处有强烈吸收峰, 随着金纳米线直径增加, 吸收峰红移, 当金纳米线直径达到200 nm时, 其吸收峰峰位移至700 nm. 结合金纳米颗粒相关表面等离子体共振吸收效应对实验结果进行了讨论.     

Co/Cu多层纳米线阵列的制备与磁性能

利用双槽直流电沉积技术在阳极氧化铝(AAO)模板的纳米孔中获得调制波长为50 和200 nm 的Co/Cu多层纳米线, 多层纳米线的调制波长由电沉积时间控制. 运用扫描电子显微镜(SEM)和透射电子显微镜(TEM)表征纳米线的形貌, Co/Cu多层纳米线的长度约20 μm, 直径约80 nm; 用X射线衍射(XRD)研究多层线的结构; 用振动样品磁强计(VSM)测试纳米线阵列的磁性能; 利用可变磁场结合高灵敏度恒流装置研究巨磁电阻(GMR)特性. 结果表明, Co/Cu多层纳米线具有磁各向异性. 当磁场与纳米线平行和垂直时, 调制波长为50 nm的多层线的矫顽力分别为87500 和34200 A·m-1, 而调制波长为200 nm的多层线阵列的矫顽力分别为28600 和8000 A·m-1. 调制波长为50 nm的多层纳米线的磁电阻变化率高达-%, 而调制波长为200 nm的多层线未产生明显的GMR效应.