固相浸渍法制备NiO/CeO2催化剂及其在CO氧化反应中的应用

采用固相浸渍法制备了一系列NiO/CeO2催化剂,并通过与常规湿浸渍法比较,考察了制备方法对催化剂和CO氧化反应性能的影响.同时结合X射线衍射(XRD),N2吸附-脱附(BET),透射电镜(TEM),氢气-程序升温还原(H2-TPR),拉曼(Raman)光谱,X射线光电子能谱(XPS)等手段对催化剂的结构和表面物种分散状态进行了表征.CO氧化活性测试结果表明,当镍负载量相同时,固相浸渍法制备的催化剂相比于湿浸渍法表现出更好的催化性能.TEM、XPS、H2-TPR结果表明,固相浸渍法更有利于加强镍铈间的相互作用和得到高分散的镍物种,从而促进镍物种的还原.Raman结果表明固相浸渍法相比于湿浸渍法能产生更多氧空位,这有利于氧气在催化剂表面的活化,使得CO氧化反应更容易进行.     

镍促进CuO-CeO2催化剂的结构表征及低温CO氧化活性（英文）

制备了一系列CO低温氧化的Ce20Cu5NiyOx催化剂,并采用氮气低温物理吸附、X射线衍射、程序升温还原、X射线光电子能谱以及拉曼光谱等手段对催化剂进行表征.结果表明,Ce20Cu5Ni0.4Ox催化剂活性最高.NiO的添加可以使得较多的Cu物种掺杂到CeO2晶格中,通过形成铈镍固溶体产生更多的氧空位.表征结果显示,Ce20Cu5Ni0.4Ox催化剂中存在大量的Cu+,Ce3+及晶格氧,催化剂中的Cu+很容易进入到氧化铈晶格,形成Cu-O-Ce固溶体,从而增强了在还原气氛下晶格氧的释放能力.Ce20Cu5Ni0.4Ox催化剂高的催化活性主要归因于大量Cu+以及形成的Cu-O-Ce和Ni-O-Ce固溶体.     

氮气气氛下焙烧的CeO_2载体负载Ni基催化剂的顺酐加氢性能研究

在氮气气氛中合成了具有较高氧缺陷浓度的CeO_2载体,采用浸渍法制备了Ni含量为10%的Ni/CeO_2-N催化剂,考察了其顺酐液相加氢性能,并与氧气气氛中制得的CeO_2载体负载Ni催化剂作了对比.N_2低温物理吸脱附,X-射线衍射,拉曼光谱,H_2程序升温还原等表征手段表明,在氮气气氛中合成的CeO_2具有较高浓度的氧缺陷位,在催化剂还原过程中可促进NiO物种的还原,同时在催化剂表面生成更多的氧缺陷位.该氧缺陷位可与活性金属Ni物种协同作用,显著提高催化剂的C=C及C=O加氢活性.     

吸附相反应技术制备MnO_x/CeO_2/SiO_2催化剂及其低温选择性催化还原NO_x

采用吸附相反应技术制备得到了MnOx/CeO2/SiO2催化剂,通过X射线衍射(XRD)、透射电子显微镜(TEM)、高分辨透射电子显微镜(HRTEM)、紫外激光拉曼(Raman)等手段对催化剂进行了表征.HRTEM分析表明活性组分MnOx与CeO2都均匀分布在载体SiO2表面;XRD分析表明Mn3O4特征峰随着CeO2含量的增加逐渐减小至完全消失,CeO2的加入降低了MnOx的结晶程度,增加了MnOx的分散性;Raman光谱表明催化剂表面的Mn离子能够进入CeO2晶格,激发出空穴氧,随着CeO2负载量的增加,催化剂氧空穴浓度先升高后降低.以NH3为还原剂,考评催化剂的NOx低温选择性催化还原(SCR)性能,催化剂催化活性随CeO2负载量增加先升高后降低,与催化剂氧空穴浓度变化规律一致,说明催化剂活性受氧空穴浓度影响,氧空穴浓度升高,催化剂催化活性升高.     

Ni2 在炭包覆氧化铝表面存在状态及加氢性能

采用等体积浸渍法制备了以炭包覆氧化铝(CCA)为载体的Ni基催化剂.利用低温N2物理吸附、XRD、UV-Vis DRS、H2-TPR、H2-TPD等手段对催化剂进行表征,并考察了催化剂粗1,4-丁二醇加氢反应性能.结果表明,均匀分散在表面的炭可以有效阻止Ni2+进入氧化铝表面四面体及八面体空位,Ni2+以与载体具有中等强度相互作用的物种形式存在.随Ni含量的增加,镍物种晶粒尺寸发生明显变化,当Ni含量低于10%时,NiO以高分散状态存在于载体表面,Ni含量达到14%时催化剂中出现了NiO微晶,进一步提高Ni含量,NiO晶粒尺寸有所长大,但仍保持了较高的分散度.由于Ni的聚集程度较小,随着Ni含量增加,Ni的总活性比表面积增加,催化剂加氢活性提高,至Ni含量达17%时,催化剂表现出最佳的催化加氢活性.     

Ru-La_2O_3/γ-Al_2O_3催化剂合成、表征及CO选择氧化

采用浸渍法制备系列Ru-La2O3/γ-Al2O3复合氧化物催化剂,通过XRD、H2-TPR、CO-TPR、XPS、BET等方法对催化剂进行表征,考察La2O3的加入量、预处理方法对催化剂上CO选择氧化性能的影响.结果表明,110-170℃时Ru1La6/Al2O3催化剂上CO转化率达到99%以上,氧气利用率达55.7%以上.和Ru/Al2O3相比,Ru1La6/Al2O3催化剂在较低温度具有高活性,活性温度区间变宽.适量La2O3的加入促进了活性组分在载体表面分散,提高了催化剂的活性.经氢气预处理的Ru1La6/Al2O3催化剂活性最佳,催化剂上Ru物种结合能降低,表面钌物种活性位增多,且表面晶格氧浓度增大,更有利于CO气体在催化剂表面上的氧化反应.     

Dispersion of Ni^（2＋） Supported on Carbon Covered Alumina Surface and Hydrogenation Performance

采用等体积浸渍法制备了以炭包覆氧化铝（CCA）为载体的Ni基催化剂.利用低温N2物理吸附、XRD、UV-Vis DRS、H2-TPR、H2-TPD等手段对催化剂进行表征,并考察了催化剂粗1,4-丁二醇加氢反应性能.结果表明,均匀分散在表面的炭可以有效阻止Ni2＋进入氧化铝表面四面体及八面体空位,Ni2＋以与载体具有中等强度相互作用的物种形式存在.随Ni含量的增加,镍物种晶粒尺寸发生明显变化,当Ni含量低于10%时,NiO以高分散状态存在于载体表面,Ni含量达到14%时催化剂中出现了NiO微晶,进一步提高Ni含量,NiO晶粒尺寸有所长大,但仍保持了较高的分散度.由于Ni的聚集程度较小,随着Ni含量增加,Ni的总活性比表面积增加,催化剂加氢活性提高,至Ni含量达17%时,催化剂表现出最佳的催化加氢活性.     

铈和镧改性γ-Al2O3担载Pd催化剂的结构效应

分别以镧-铈、铈-镧顺序浸渍和镧铈共浸渍的方式在γ-Al2O3载体上引入助剂La2O3和CeO2,然后担载Pd制备了一系列催化剂.以甲醇分解为探针反应,采用XRD、EXAFS和XPS对催化剂的体相和表面结构进行表征,用BET法测定比表面积,并进行了吸附态CO的FTIR研究.结果表明,La2O3容易进入CeO2的晶格中,促进了CeO2在γ-Al2O3上的分散.但不同的La2O3、CeO2加入方式对活性组分Pd在改性载体上的分散度、优势暴露面及其与CeO2之间的相互作用产生不同的影响.关联甲醇分解性能测试结果说明,Pd在载体上的高度分散以及Pd和CeO2之间通过界面产生的强相互作用是催化剂具有高活性的关键.     

不同CuO/CeO2催化剂上CO低温氧化反应

 分别用热解硝酸铈法和浸渍法制备了不同物性的CeO2粉体和相应的CuO/CeO2催化剂,并用XRD, HRTEM和TPR等对样品进行了表征,利用微反-色谱装置考察了其催化CO低温氧化的活性. 结果表明,热解温度影响CeO2的物性(形貌、粒度大小及分布等). 相同条件下,不同物性的CeO2载体上CuO的负载情况不同, 500 ℃热解获得的CeO2载体上非晶态CuO负载量最高,相应的CuO/CeO2催化剂活性也较高. 非晶态CuO一部分进入CeO2晶格,另一部分高度分散于CeO2表面上. 焙烧温度较低时(≤ 600 ℃), 催化剂活性受焙烧温度的影响较小,而高温(800 ℃)焙烧后,催化剂则因载体粒度增大和CuO烧结团聚等因素导致催化活性明显降低.     

铈和镧改性γ-Al2O3担载Pd催化剂的结构效应

分别以镧-铈、铈-镧顺序浸渍和镧铈共浸渍的方式在γ-Al2O3载体上引入助剂La2O3和CeO2，然后担载Pd制备了一系列催化剂.以甲醇分解为探针反应，采用XRD、EXAFS和XPS对催化剂的体相和表面结构进行表征，用BET法测定比表面积，并进行了吸附态CO的FTIR研究.结果表明,La2O3容易进入CeO2的晶格中，促进了CeO2在γ-Al2O3上的分散.但不同的La2O3、CeO2加入方式对活性组分Pd在改性载体上的分散度、优势暴露面及其与CeO2之间的相互作用产生不同的影响.关联甲醇分解性能测试结果说明,Pd在载体上的高度分散以及Pd和CeO2之间通过界面产生的强相互作用是催化剂具有高活性的关键.     

Theoretical study of the ethane ionization spectra within the correlation hole model

This work is an extension of a previous study on the assignment of the peaks of the photoionization spectrum of C₂H₆ [1]. The model of the correlation hole is reconsidered in order to carry out a new study of the states² A _1g ,² E _g ,² E _u and² A _2u of the C₂H ₆ ⁺ The qualitative relations which the average mass of the electrons in the Coulomb hole must have for the four states of the C₂H ₆ ⁺ , lead to a new criterion for the assignation of the peaks of the spectrum. The arrangement obtained for the two lower peaks is in agreement with those obtained previously [1].     

乙烷与CO2制乙烯反应的热力学和动力学研究

乙烷与ＣＯ２的主要反应及其热力学研究表明，乙烷与ＣＯ２反应很复杂，提高ＣＯ２氧化乙烷脱氢生成乙烯的选择，关键在一催化剂的开发；ＣＯ２不但可提高乙灶脱氢制乙烯的热力学平衡转化率，而且可与催化剂表面的积碳发生反应，延长催化剂的使用寿命。研究了催化剂上乙烷与ＣＯ２制乙烯反应的动力学，确定了ＣＯ２氧化乙烷脱氢反应的动力学方程及参数，表明乙烷与ＣＯ２制乙烯的反应速度比乙烷热裂解制乙烯的反应速度要大得多。     

Partial oxidation of ethane in H2/O2 fuel cell under mild conditions

The partial oxidation of ethane to ethanol and acetaldehyde in the H₂/O₂ fuel cell under mild conditions is reported. The reaction proceeds at the carbon gasdiffusion cathode in the presence of transition metal ions (Fe²⁺, Cu²⁺) at ambient pressure and temperature 343 K.     

Ni基催化剂上CH4、C2H6和C2H4的裂解积炭性能

采用脉冲微反技术研究了添加半导体氧化物对Ni基催化剂上CH4、C2H6和C2H4的裂解积炭反应特性的影响。结果表明,n型半导体CeO2的添加降低了CH4和C2H6的积炭活性,而p型半导体Co3O4的添加则加速CH4和C2H6的裂解积炭;而对于与CH4和C2H6活化机制不同的C2H4分子的活化,上述影响机制正好相反,n型半导体CeO2的添加促进C2H4的裂解积炭反应,而p型半导体Co3O4的添加则抑制C2H4的裂解积炭反应。XPS分析表明,活性金属Ni与半导体氧化物之间存在的金属 半导体相互作用是这种影响机制的主要因素。     

Infrared diode laser absorption spectroscopy of C(2)H(2) and C(2)H(6) in capacitively coupled methane RF discharges

Low-temperature RF discharges with methane as feed gas are widely used for the deposition of hydrogenated films. The film properties depend strongly on the chemical composition and therefore two of the main stable products in this kind of discharge, namely ethane (C(2)H(6)) and acetylene (C(2)H(2)), have been measured for the understanding of the reaction kinetics in the plasma. An absorption spectrometer has been built up for the investigation of the concentrations of these as a function of the input power and the flow rate. The time scales for reaching steady state after the discharge is switched on and the depletion time scale after the plasma is switched off have been determined. Assuming the recombination of CH(3) molecules to be the only production mechanism for C(2)H(6) and using a simplified rate equation, the measured densities of C(2)H(6) can be reproduced very well by analytical fitting curves.     

Behavior of ethylene and ethane within single-walled carbon nanotubes, 2: dynamical properties

The dynamical behavior of ethylene and ethane confined inside single-walled carbon nanotubes has been studied using Molecular Dynamics and a fully atomistic force field. Simulations were conducted at 300 K in a broad range of molecular densities, 0.026 mol⋅L⁻¹<ρ<15.751 mol⋅L⁻¹(C₂H₄) and 0.011 mol⋅L⁻¹<ρ<14.055 mol⋅L⁻¹(C₂H₆), and were oriented towards the determination of bulk and confined phase self-diffusion coefficients. In the infinite time limit, Fickian self-diffusion is the dominant mode of transport for the bulk fluids. Upon confinement, there is a density threshold (ρ=5.5 mol⋅L⁻¹) below which we observe a mixed mode of transport, with contributions from Fickian and ballistic diffusion. Nanotube topology seems to have only a small influence on the confined fluids’ dynamical properties; instead density (loading capacity) assumes the dominant role. In all cases studied and at a given density, the diffusivities of ethylene are larger than those of ethane, although the difference is relatively minor. We note the collapse of self-diffusivities obtained from the bulk fluids and confined phases into a unique single trend. These results suggest that it might be possible to infer dynamical properties of confined fluids from the knowledge of their bulk phase densities. Electronic Supplementary Material  The online version of this article () contains supplementary material, which is available to authorized users.     

Ammoxidation of ethane on V-Mo-Nb oxide catalysts

Summary Catalytic and physicochemical properties of V-Mo-Nb oxide catalysts (V_0.3Mo₁Nb_x, where x = 0.05, 0.15, 0.22, and 0.27) have been studied in the ammoxidation of ethane. An increase in the Nb content in the samples is accompanied by an increase in the catalytic activity and selectivity to acetonitrile. It was established that a triple Mo₅O₁₄-like phase with a variable composition (V_{0.23 ±0.3}Mo₁Nb_x, where х = 0.2?0.37) acts as an active component in the catalyst.</o:p>     

亚微米ZSM-5负载Cr催化剂上乙烷CO2气氛下脱氢制乙烯

石油资源的日趋短缺使天然气和页岩气的开发利用受到重视,因而低碳烷烃脱氢制取低碳烯烃也随之引起了人们越来越多的关注.由于乙烷纯脱氢反应的平衡收率低,能耗高,而氧气氧化脱氢又易将乙烷深度氧化为CO2或CO,因此开发具有反应条件温和、装置投资和操作费用低等优势的CO2气氛下乙烷脱氢的技术路线日益得到重视. CrOx是该反应理想的催化剂之一, CO2的加入可使CrOx对乙烷脱氢的催化活性提升3倍,然而受困于CrOx过小的比表面积,通常将CrOx制备成负载型催化剂使用. CrOx的常见载体有Al2O3, ZrO2和SiO2等氧化物及MCM-41, SBA-15, SBA-1和MSU-x等介孔硅材料, ZSM-5作为载体负载CrOx用于低碳烷烃脱氢的研究则较少,所得结果也不甚理想.我们采用亚微米尺寸的ZSM-5作为载体制备了负载型CrOx催化剂,研究了其在CO2气氛下催化乙烷脱氢反应,发现该催化剂具有非常优异的脱氢活性,高硅铝比和Na型的ZSM-5作载体对反应更加有利,而且在反应进行50 h后,催化剂依然保持很好的活性和很高的乙烯收率,这是在一般负载型CrOx催化剂上所不能实现的.
　　X射线光电子能谱(XPS)表征发现, Na型ZSM-5载体制得的催化剂具有更高的Cr6+/Cr3+比.一般认为, Cr6+是Cr系催化剂进行低碳烷烃脱氢反应时的活性位(或活性位前驱体),因此可以初步判定, Na型载体具有很好催化效果的原因可能是由它制得的催化剂具有更多的反应活性位.程序升温还原(H2-TPR)表征结果证实了这一点, Na型载体明显具有更高的H2消耗量;也就是说, Na型载体制得的催化剂具有更多的可还原Cr物种,即脱氢活性位.进一步表征发现,反应活性还与Cr物种存在形式有关.文献报道,低聚态的Cr物种和孤立态的Cr物种比Cr2O3有更好的催化活性.通过漫反射紫外-可见光谱(UV-Vis)对Cr物种的存在形态进行表征后发现, Na型载体上Cr主要以四配位形式存在,而在H型载体上出现了对应于六配位的Cr物种;激光Raman表征结果表明, Na型载体上出现的都是低聚态Cr物种和孤立态Cr物种,而H型载体上出现了明显的对应于α-Cr2O3的峰,说明相较于H型载体, Na型载体更有利于Cr组分分散,这也是Na型ZSM-5载体催化剂具有更高活性的原因之一.
　　CO2引入后对乙烷脱氢反应具有明显的促进作用,特别是在CO2/C2H6=5时,催化剂上C2H6转化率是非CO2气氛下的3.2倍;同时, CO2的引入也提高了脱氢反应的稳定性.在非CO2气氛下,反应进行6 h后, C2H6转化率降低到初活性的60%左右,而在CO2/C2H6=5时,相同时间内催化剂活性下降仅有5%左右.实验分析了CO2对脱氢反应具有促进作用的原因.在脱氢反应温度650 oC下, CO2/H2=1时进行了逆水煤气反应测试,发现CO2的转化率达到22.5%,说明引入CO2后可以通过逆水煤气反应有效地消耗掉乙烷脱氢反应生成的H2,从而促进反应向脱氢方向进行; CO2的引入也可以促进Cr物种的CrOx/CrOx-1循环,从而提高催化剂效率,减缓催化剂失活; CO2还可与反应中生成的积碳类物质发生Boudouard反应,将反应活性位暴露出来,从而提高催化剂的稳定性. CO2气氛下反应6 h后催化剂的积碳量为3.0%,低于非CO2气氛下的3.4%,同时在脱氢反应中生成的CO量与消耗掉的CO2量的比值约为1.4,也有力地说明Boudouard反应的存在.     

乙烷氧化脱氢用Ni/Al2O3催化剂中活性镍物种前驱体（英文）

Ni/Al2O3 catalysts for oxidative dehydrogenation(ODH) of ethane were prepared by impregnation of Al2O3 with nickel acetate or nickel nitrate,and by mechanical mixing of NiO and Al2O3.The Ni-based catalysts were characterized by N2 adsorption-desorption,X-ray diffraction,diffuse reflectance UV-visible diffuse reflectance spectroscopy,and temperature-programmed reduction of hydrogen.The results showed that formation of crystalline NiO particles with a size of < 8 nm and/or non-stoichiometric NiO species in the Ni/Al2O3 catalysts led to more active species in ODH of ethane under the investigated reaction conditions.In contrast,tetrahedral Ni species present in the catalysts led to higher selectivity for ethene.Formation of large crystalline NiO particles(22-32 nm) over Ni/Al2O3 catalysts decreased the selectivity for ethene.     

An ab initio study of the Cl(P)+C2H6→C2H5+HCl abstraction reaction

Electronic energies, geometries, and harmonic vibration frequencies for the reactants, products, and transition state for the Cl(³P)+C₂H₆→C₂H₅+HCl abstraction reaction were evaluated at the HF and MP2 levels using several correlation consistent polarized-valence basis sets. Single-point calculations at PMP2, MP4, QCISD(T), and CCSD(T) levels were also carried out. The values of the forward activation energies obtained at the MP4/cc-pVTZ, QCISD(T)/cc-pVTZ, and CCSD(T)/cc-pVTZ levels using the MP2/cc-pVTZ structures are equal to −0.1, −0.4, and −0.3 kcal/mol, respectively. The experimental value is equal to 0.3±0.2 kcal/mol. We found that the MP2/aug-cc-pVTZ adiabatic vibration energy for the reaction (−2.4 kcal/mol) agrees well with the experimental value −(2.2–2.6) kcal/mol. Rate constants calculated with the zeroth-order interpolated variational transition state (IVTST-0) method are in good agreement with experiment. In general, the theoretical rate constants differ from experiment by, at most, a factor of 2.6.