CS-CMC聚合物电解质膜的制备及在电生成FeO2-4中的应用

以戊二醛为交联剂,制备了壳聚糖(CS)-羧甲基纤维素(CMC)聚合物电解质膜.用电子显微镜观察其表面形貌.IR分析表明该聚合物薄膜含有COOH,NH3+官能团,具有两性离子的特征.与CS膜或CMC膜相比,该膜能稳定存在于酸碱溶液中.膜特性研究表明CS-CMC聚合物电解质膜具有离子交换和选择性渗透能力,可作为隔膜电解制备高铁酸盐.     

CS-CMC聚合物电解质膜的制备及在电生成FeO42-中的应用

以戊二醛为交联剂, 制备了壳聚糖(CS)-羧甲基纤维素(CMC)聚合物电解质膜. 用电子显微镜观察其表面形貌. IR分析表明该聚合物薄膜含有COOH, NH₃⁺官能团, 具有两性离子的特征. 与CS膜或CMC膜相比, 该膜能稳定存在于酸碱溶液中. 膜特性研究表明CS-CMC聚合物电解质膜具有离子交换和选择性渗透能力, 可作为隔膜电解制备高铁酸盐.     

CS-CMC聚合物电解质膜的制备及在电生成FeO42-中的应用

以戊二醛为交联剂, 制备了壳聚糖(CS)-羧甲基纤维素(CMC)聚合物电解质膜. 用电子显微镜观察其表面形貌. IR分析表明该聚合物薄膜含有COOH, NH₃⁺官能团, 具有两性离子的特征. 与CS膜或CMC膜相比, 该膜能稳定存在于酸碱溶液中. 膜特性研究表明CS-CMC聚合物电解质膜具有离子交换和选择性渗透能力, 可作为隔膜电解制备高铁酸盐.     

PVA-CMC-KOH-H_2O碱性聚合物电解质研究

由聚乙烯醇(PVA)与羧甲基纤维素钠(CMC)制备PVA-CMC-KOH-H2O碱性聚合物电解质膜,应用交流阻抗、循环伏安、差热分析和红外光谱等实验方法表征、研究其性能.结果表明,该碱性聚合物电解质的室温电导率可达到10-2S.cm-1数量级,在不锈钢惰性电极上的电化学稳定窗口约为1.6 V.另外,还研究了聚合物电解质膜中KOH、H2O和CMC对体系电导率的影响以及PVA-CMC-KOH-H2O碱性聚合物电解质在N i/MH电池中的初步应用.初步结果表明,由PVA-CMC-KOH-H2O聚合物电解质组装的N i/MH电池,其低倍率放电性能较好.     

多羧基酞菁铜、乙酰基二茂铁改性CMC/CS双极膜的制备及表征

柔性链高分子聚乙二醇(PEG)分别与阳离子交换膜层羧甲基纤维素钠(CMC)、阴离子交换膜层壳聚糖(CS)共混以增强界面的相容性和膜的机械性能.以金属有机高分子多羧基酞菁铜(CuPc)改性CMC、乙酰基二茂铁改性CS,采用流延法制备了CuPc-mCMC/mCS双极膜.双极膜溶胀性和热重分析结果表明膜改性后稳定性能得到提高.膜交流阻抗、I-V工作曲线的测定结果表明该双极膜阻抗及工作电压均较小.双极膜经改性具有较高的离子渗透性能。     

分子复合法制备新型聚合物驱油剂CMC/P(AM-DMDAAC)

通过具有互补结构的阴离子聚合物羧甲基纤维素(CMC)与阳离子聚合物聚(丙烯酰胺-二甲基二烯丙基氯化铵)[P(AM-DMDAAC)]间的聚电解质分子复合作用,制备了分子复合型CMC/P(AM-DMDAAC)新型驱油剂.电导率测定及紫外光谱分析结果表明,CMC与P(AM-DMDAAC)可以在水相通过库仑力形成均相聚电解质复合溶液.由于分子复合形成的独特超分子结构,复合溶液粘度显著增加,分别为组分聚合物溶液的5.2倍和9.0倍,在高温和高剪切环境中的粘度保持能力也明显优于其组分聚合物.     

改性壳聚糖膜用于醇水混合液分离的研究(Ⅱ)─壳聚糖－羧甲基纤维素共混物膜

制备了壳聚糖(CS)─羧甲基纤维素(CMC)共混物膜(I-2),对其成膜反应、溶胀度、交联度及拉伸强度进行了研究,结果表明,壳聚糖与羧甲基纤维素共混物在成膜的同时还发生交联反应;当CS/CMC=1时,交联度最大,此时共混物膜不溶于稀醋酸水溶液。首次将此共混物膜用于乙醇/水混合液的分离,该膜具有优良的醇水分离性能,当CS/CMC=1时,渗透通量和分离因子皆达到最大值[J=0.9kg/(m²·h),a=800,90wt%乙醇,45℃],且该膜的分离因子基本上不随温度变化,醇水透过I-2膜的表现活化能△E为32.6kJ/mol.对CS/CMC2+2+2+2+次序递增,分离因子变化次序则刚好相反。     

聚偏氟乙烯电纺膜及其电化学性能的研究

用电纺的方法制备了聚偏氟乙烯纳米纤维膜,它们具有多微孔结构,能够作为锂电池聚合物电解质.电纺中聚合物溶液的浓度对制备的电纺膜的结构形态有很大的影响,低浓度(10 wt%)时得到珠丝结构的膜,浓度15 wt%时则为纤维结构,而高浓度(18 wt%)时,电纺膜为交联的网状结构.用电纺法制备的聚偏氟乙烯纳米纤维微孔膜具有较高的孔隙率,而且它们与锂金属电极具有良好的界面稳定性;在25℃时吸液率最高可达340%,以这种膜制备的聚合物电解质室温电导率可达到1.57×10-3S.cm-1;由该电解质组装的扣式电池以0.5 mA.cm-2恒流充放电,25℃时50次循环后几乎无容量损失,具有良好的循环性能;即使60℃时,电池仍能保持良好的工作稳定性.     

磷酸化P-mCMC/mCS双极膜的制备及其性能的研究

以五氧化二磷,磷酸三乙酯和磷酸为反应剂,制备了磷酸化羧甲基纤维素(CMC),经Fe³⁺改性后用作为阳膜;以壳聚糖(CS)和聚乙烯醇共混物用戊二醛改性后用作为阴膜溶胶,将阴膜溶胶流延于阳膜上,制备了P-mCMC/mCS双极膜。测定了CS、CMC胶体的电荷密度,离子透过率,P-mCMC/mCS双极膜的红外光谱与离子交换能力。IR与接触角测定的结果表明,CMC经改性后其亲水性能得到了显著提高。膜交流阻抗、I-V工作曲线的测定结果表明该双极膜阻抗及工作电压均较小。     

一种高离子电导率复合聚合物电解质的简易热处理制备

固态聚合物电解质是发展柔性全固态锂离子电池的核心,但是目前室温离子电导率低限制了其应用.本研究以热聚合方法制备石墨相氮化碳(g-C_3N_4),并将其与聚氧化乙烯/高氯酸锂(PEO/LiClO_4)共混制备复合聚合物固态电解质.采用X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、光学显微镜(OM)、扫描电子显微镜(SEM)、差示扫描量热仪(DSC)和电化学工作站对复合聚合物电解质膜进行表征.结果表明,通过120℃退火-淬冷热处理及复合聚合物电解质内部的相互作用,可以较大程度抑制PEO的结晶,从而使该复合聚合物固态电解质膜的离子电导率在25℃时达到2.4×10~(-5)S cm~(-1),提高了3个数量级.     

用聚电解质渗透汽化膜进行乙醇脱水

渗透汽化 (PV)膜过程由于可用于有机 /有机及有机 /水的恒沸或近沸混合物的分离而成为近年来膜技术研究开发的热点[1,2 ] .德国 GFT公司所制的富马酸交联 PVA脱水膜[3] 对温度为 80℃的 80 %Et OH料液 ,其分离因子为 350 ,渗透通量为 2 0 0 g/ (m2 ·h) .优秀的分离膜要求渗透通量大 ,同时具有较高的分离因子和良好的稳定性 .因此 ,提高膜的分离性能是渗透汽化技术开发应用的关键 .周继青等 [4 ]研究了 PVA/ PVP互穿网络膜的渗透汽化性能 ,发现膜的渗透通量虽有明显提高 ,但膜的选择性下降 .聚电解质具有优良的亲水性 ,可制得高水通…     

Evaluation of modified CMC and CMC-PVA as miscible polymer blend membranes for hepatocytes

CMC and CMC-PVA were blended either with type I collagen, BSA or CS to obtain biocompatible membranes for evaluation as potential hepatocyte culture substrates. Pure and modified forms of CMC showed distinct surface, mechanical, and cell attachment properties. While the hydrophilicity decreased, the mechanical stability and the porosity of CMC membranes increased after blending. Serum proteins were adsorbed by all types of membranes. Among eight membranes tested, collagen-modified CMC was found to be a suitable membrane material for hepatocyte culture, in terms of mechanical and cell interaction properties.     

Chondroitin Sulfate Fluorescence Biosensor Based on Graphere Quantum Dots Aggregating on CMC/CS Polyelectrolyte Microspheres

Here, we report an efficient fluorescence biosensor for chondroitin sulfate(CHS) based on polyelectrolyte microspheres of carboxymethyl cellulose(CMC) and chitosan(CS) composites inducing the aggregation of graphene quantum dots(GQDs), calling CMC/CS-GQDs. The polyelectrolyte microspheres(CMC/CS microspheres) were fabricated by using anioniccationic electrostatic attraction between CMC and CS by high voltage electrostatic spray technology. The aggregating process of GQDs was based on the anionic-cationic electrostatic attraction as well. After combing with the polyelectrolyte microspheres, the fluorescence of GQDs disappeared. CHS, which widely consists in the cell surface of human beings and animals, carries a large number of negative charges on the surface. The addition of CHS enabled CHS and GQDs to compete with each other to composite with the CMC/CS microshpheres. As a result of the higher surface charge density of CHS, CMC/CS-CHS formed accompanied by the release of GQDs, and the fluorescence of the system recovered. The CHS content was detected by analyzing the system's fluorescence recovery, which suggested that the obtained fluorescence biosensor can accurately detect the concentration of CHS. The test results showed that the linear range of the fluorescence recovery for this biosensor with respect to CHS was 0~12.00 mg/mL, and the detection limit was 10-8 M. Besides, to test the stability of the biosensor, the CMC/CS-GQDs micropsheres persisted for one month, with a low fluorescence quenching of 9.48%. These results suggested that CMC/CS-GQDs can be utilized as efficient fluorescence biosensor for the detection of CHS. Moreover, the detection method was simple and efficient, and could be widely popularized.     

mCMC-PEG-CS双极膜在电还原制备巯基乙酸中的应用

以Fe3+改性羧甲基纤维素(CMC)和聚乙二醇(PEG)共混物为阳膜, 以戊二醛改性壳聚糖(CS)和聚乙二醇共混物为阴膜, 制备了mCMC-PEG-CS双极膜, 并将其用作电解还原制备巯基乙酸(TGA)电解槽中阴阳两室间的隔膜. 以硫代硫酸钠法合成的巯基乙酸(TGA)和二硫代二乙酸(DTDGA)混合物为原料, 研究了酸浓度、温度及电解电流密度对电还原DTDGA制备TGA的生成量和电流效率的影响. 实验结果表明, 在TGA初始合成质量分数为2.79%, 电流密度为10 mA/cm2, 35 ℃电解时, 阴极室电还原产物巯基乙酸的电流效率为74.69%, 电解过程中的平均电流效率为54.02%. 与传统的金属还原法还原DTDGA制备的TGA相比, 不仅避免了昂贵的金属还原剂锌的消耗, 而且消除了反应副产物锌泥对环境的污染.     

Ni-P-mCMC/mCS双极膜技术在成对电解制备糠醇、糠酸中的应用

以磷酸化试剂改性羧甲基纤维素钠(mCMC)制备了阳膜层,以戊二醛改性壳聚糖(mCS)制备了阴膜层溶胶,将阴膜层溶胶流延于阳膜层上,制备了P-mCMC/mCS双极膜,而后以化学镀方法在阳膜层表面镀镍,制备了Ni-P-mCMC/mCS双极膜,并应用于成对电合成糠醇(阴极室中)、糠酸(阳极室中)。在电场的作用下,双极膜中水电离后生成的H+透过mCMC阳离子膜进入阴极室,促进糠醛电还原生成糠醇过程的进行;OH-透过mCS阴离子膜进入阳极室,与糠醛电氧化生成糠酸过程中产生的H+结合生成H2O,以增大正向反应的速度。在电流密度为2.5×10-2A/cm2,30℃下电解,阴阳两极室的电解效率分别为83.0%和77.4%,电解槽电压稳定在3.0V左右。     

Chitosan‐modified graphene oxide as a modifier for improving the structure and performance of forward osmosis membranes

Chitosan (CS) with good hydrophilicity and charged property was used to modify graphene oxide (GO), the obtained GO‐CS was used as a novel modifier to fabricate thin film composite forward osmosis (FO) membranes. The results revealed that the amino groups on CS reacted with carboxyl groups on GO, and the lamellar structure of the GO nanosheets was peeled off by CS, resulting in the reducing of their thicknesses. The GO‐CS improved the hydrophilicity of polyethersulfone (PES) substrate, and their contact angles decreased to 64° with the addition of GO‐CS in the substrate. GO‐CS also increased the porosity of the substrate and surface roughness of FO membrane, thereby optimizing the water flux and reverse salt flux of FO membrane. The average water flux of the FO membrane reached the optimal flux of 21.34 L/(m² h) when GO‐CS addition was 0.5 wt%, and further addition of GO‐CS to the substrate would decrease the water flux of FO membrane, and the reverse salt flux also decreased to the lowest value of 2.26 g/(m² h). However, the salt rejection of the membrane increased from 91.4% to 95.1% when GO‐CS addition increased from 0.5 to 1.0 wt% under FO mode using 1 mol/L sodium chloride (NaCl) solution as draw solution (DS). In addition, high osmotic pressure favored water permeation, and at the same concentration of DS, magnesium chloride (MgCl₂) exhibited better properties than NaCl. These results all suggested that GO‐CS was a good modifier to fabricate FO membrane, and MgCl₂ was a good DS candidate.