碱性纳米复合聚合物电解质研究

为了提高聚氧化乙烯(PEO)/KOH 基碱性聚合物电解质的电导率, 制电解质膜时分别将纳米 TiO2、纳米β-Al2O3和纳米 SiO2添加到 PEO/KOH 体系中, 制备出了兼顾电学和力学性能的碱性纳米复合聚合物电解质. 交流阻抗测试显示, 其室温(28 ℃)电导率可达到 10-3 S?cm-1数量级. 循环伏安研究表明, 制得的电解质膜在不锈钢惰性电极上的电化学稳定窗口约为 1.6 V. 分别研究了聚合物电解质膜中 KOH, H2O, 无机纳米粉末的含量以及温度对体系电导率的影响.     

“Water-in-salt”聚合物电解质制备及其电化学性能研究

为提高柔性锂离子电池安全性和循环稳定性能,本实验以自由基聚合结合冷冻干燥得到的聚丙烯酰胺膜为电解质载体,引入21 mol·kg^-1 LiTFSI 高浓度电解液,得到“water-in-salt”聚合物电解质。通过聚合物膜的形貌和孔道结构表征,红外光谱分析,离子电导率及电化学稳定窗口测试等对其基本物化特性进行了研究。冷冻干燥得到的聚丙烯酰胺膜内部具有大量微孔结构,有利于电解液的载入。将该吸附了电解液的聚合物电解质膜与锰酸锂(LiMn₂O₄)正极和磷酸钛锂(LiTi₂(PO₄)₃)负极组装全电池进行充放电性能测试。结果表明,制得的柔性聚合物电解质具有良好的拉伸性能,高离子电导率(20°C,4.34 mS·cm^-1)和宽电化学稳定窗口(3.12 V)。以“water-in-salt”聚合物电解质为隔膜组装的LiMn₂O₄||LiTi₂(PO₄)₃ 全电池表现出优异的倍率性能和长循环稳定性。     

PVA-膨润土-KOH-H2O复合碱性聚合物电解质的制备与表征

以聚乙烯醇(PVA)与膨润土(bentonite)和氢氧化钾为原料, 采用溶液浇铸法制备了PVA-膨润土-KOH-H2O复合碱性聚合物电解质膜. 运用X衍射(XRD)、扫描电镜(SEM)和循环伏安(CV)等技术对复合膜进行了表征, 分析了膨润土对聚合物膜电导率的影响. 结果表明, 膨润土对电解质的导电性能具有双重作用: 一方面膨润土本身会阻塞PVA内部结构中的部分离子通道, 导致复合电解质的电导率降低; 另一方面, 膨润土有助于体系中KOH含量的增加, 同时PVA-膨润土相界面高导电性缺陷层的形成有助于体系电导率的提高. 当体系水的质量分数较低时, 复合电解质体系电导率存在极大值; 当w(H2O)为65%时, 则观察到电导率的线性增加趋势; 电解质最高室温电导率达0.110 S·cm-1. XRD图谱显示适当配比的复合膜中PVA呈无定形态; SEM结果证实了适当配比的复合膜中存在大量微米级孔径的微孔通道. 循环伏安曲线表明PVA-膨润土-KOH-H2O碱性聚合物电解质膜有约2.0 V的较宽电化学稳定窗口.     

一种高离子电导率复合聚合物电解质的简易热处理制备

固态聚合物电解质是发展柔性全固态锂离子电池的核心,但是目前室温离子电导率低限制了其应用.本研究以热聚合方法制备石墨相氮化碳(g-C_3N_4),并将其与聚氧化乙烯/高氯酸锂(PEO/LiClO_4)共混制备复合聚合物固态电解质.采用X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、光学显微镜(OM)、扫描电子显微镜(SEM)、差示扫描量热仪(DSC)和电化学工作站对复合聚合物电解质膜进行表征.结果表明,通过120℃退火-淬冷热处理及复合聚合物电解质内部的相互作用,可以较大程度抑制PEO的结晶,从而使该复合聚合物固态电解质膜的离子电导率在25℃时达到2.4×10~(-5)S cm~(-1),提高了3个数量级.     

用于聚合物镍氢电池的新型PVA/SiO2碱性微孔聚合物电解质

采用溶胶凝胶法,结合相转移法和碱液活化法制备了PVA/SiO2碱性微孔聚合物电解质,通过SEM、XRD、交流阻抗法和循环伏安法表征了电解质的结构与电化学性能.研究表明,PVA/5ωSiO2(ω为质量分数)共混膜上的微孔大小合适,聚合物电解质的离子电导率最大可达1.62×10-2 S·cm-1,电化学稳定窗口2V以上;将PVA/SiO2碱性微孔电解质组装成聚合物镁基镍氢电池,与传统镍氢电池相比,循环稳定性大大增加.     

碱性聚合物电解质膜的表面锥形阵列结构提升燃料电池性能

燃料电池作为一种清洁高效的能量转换装置,被认为是构建未来社会可再生能源结构的关键一环。不同于质子交换膜燃料电池(PEMFC),碱性聚合物电解质燃料电池(APEFC)的出现使非贵金属催化剂的使用成为可能,因而受到了日益广泛的关注和研究。APEFC的关键结构是膜电极,主要由聚合物电解质膜和阴阳极(含催化层、气体扩散层)组成,膜电极是电化学反应发生的场所,其优劣直接决定着电池性能的好坏。因此,基于现有的碱性聚合物电解质及催化剂体系,如何构筑更加优化的膜电极结构,使APEFC发挥出更高的电池性能是亟待开展的研究。本文首先通过模板法在碱性聚合物电解质膜的表面构建出有序的锥形阵列,再将具有阵列结构的一侧作为阴极来构筑膜电极,同时,作为对比,制备了由无阵列结构的聚合物电解质膜构筑而成的膜电极,最后对基于两种不同膜电极的APEFC的电化学性能进行了对比研究。实验结果表明,锥形阵列结构可以将APEFC的峰值功率密度由1.04 W·cm-2显著提高到1.48 W·cm-2,这主要归因于在APEFC的阴极侧具有锥形阵列结构的聚合物电解质膜的亲水性的提升和催化剂电化学活性面积的增加。本工作为碱性聚合物电解质燃...     

用于聚合物镍氢电池的新型PVA/SiO2碱性微孔聚合物电解质（英文）

采用溶胶凝胶法,结合相转移法和碱液活化法制备了PVA/SiO2碱性微孔聚合物电解质,通过SEM、XRD、交流阻抗法和循环伏安法表征了电解质的结构与电化学性能.研究表明,PVA/5ωSiO2(ω为质量分数)共混膜上的微孔大小合适,聚合物电解质的离子电导率最大可达1.62×10-2 S cm-1,电化学稳定窗口2 V以上;将PVA/SiO2碱性微孔电解质组装成聚合物镁基镍氢电池,与传统镍氢电池相比,循环稳定性大大增加.     

增塑剂对PVA碱性聚合物电解质电化学性能的影响

通过溶解―铸膜法制备聚乙烯醇(PVA)-KOH-H2O碱性聚合物电解质膜。向聚合物中添加增塑剂丙三醇(GROL)和碳酸丙烯酯(PC)来提高离子电导率。X射线晶体衍射分析(XRD)结果表明,添加增塑剂未改变聚合物的物相结构,薄膜仍主要为不定形态。差示扫描热分析(DSC)结果显示,添加增塑剂后聚合物电解质膜的玻璃化转变温度降低,促进了电解质膜向不定形态转变。电解质膜室温离子电导率随增塑剂添加而增大,增塑剂超过一定量后离子电导率开始下降。PC对提高离子电导率的作用优于GROL。循环伏安测试结果显示,电解质膜的电化学稳定性窗口随增塑剂的添加而有所变窄,但仍显示了较好的电化学稳定性。     

聚乙烯醇/聚乙烯吡咯烷酮碱性复合膜的制备及其性能

通过在不同浓度KOH溶液中进行掺杂,制备出了聚乙烯醇/聚乙烯吡咯烷酮(PVA/PVP)碱性聚合物电解质膜.详尽考察了膜的组成、微观结构、热稳定性、离子电导率和甲醇吸收率.结果表明,PVA与PVP两者具有较好的相容性,当m(PVA)∶m(PVP)=1∶0.5时,膜断面致密、均匀,未发生大尺度相分离.PVP的混入可以极大提高复合膜的电导率和热稳定性.当m(PVA)∶m(PVP)=1∶1时,复合膜的电导率可达2.01×10-3 S.cm-1.PVA/PVP/KOH膜的甲醇吸收率随温度的升高没有明显变化,100℃时其甲醇吸收率仅为同条件下Nafion 115膜的1/4.这表明该复合膜有望作为一种新型的碱性直接甲醇燃料电池用固体电解质膜且可提高膜的使用温度.     

表面覆CoOOH的球形Ni(OH)_2的制备及快充性能

应用化学沉淀-电化学氧化法,于球形N i(OH)2颗粒表面生成CoOOH包覆层,研究包覆处理对AA型高容MH/N i电池快充性能的影响,并由红外光谱和扫描电镜表征覆钴样品.结果表明,以包覆CoOOH的N i(OH)2作正极活性材料装配的电池较之于正极单一添加CoO的电池,其内阻降低了约3.4 mΩ,该电池快充时充电电压平台较低且在充电末期电池温度不超过55℃,首次放电效率达90.6%,快充循环寿命达300周次.     

A lithium secondary battery using a thin film of polymer electrolyte as a separator

Ion-conductive polymer which shows an ionic conductivity (σ_i) of 1.4 × 10^?4S/cm at 25°C when mixed with LiClO₄ (molar ratio in Li/OE = 0.05) was used as a separator of electrodes in a lithium secondary battery. The effect of high ionic conductivity on the performance of the battery was studied. The polymer structure was and the cathode was comprised of poly(1,3,4-thiadiazole disulfide), graphite powder and the polymer electrolyte. The cell [(?)Li/polymer electrolyte/graphite–poly(disulfide) (+)] had an open circuit voltage (V_oc) of 3.25 V, a plateau voltage of 2.75 V, a discharge density (i_d) of 0.05 mA/cm² with the cathode utilization of 63%, and achieved over several tens of cycles at 25°C.     

锂离子电池PMMA-VAc聚合物电解质的制备与性质研究

以甲基丙烯酸甲酯(MMA)和醋酸乙烯酯(VAc)为单体, 用乳液聚合法合成聚甲基丙烯酸甲酯-醋酸乙烯酯聚合物(PMMA-VAc), 并以此聚合物制备了新型聚烯烃膜支撑的聚合物膜及聚合物电解质. 用红外光谱(FTIR)、凝胶色谱(GPC)、差热和热重分析(DSC/TG)、扫描电镜(SEM)及电池充放电实验等方法研究了聚合物、聚合物膜和聚合物电解质的性质. 红外光谱结果表明, MMA与VAc通过各自的C＝C双键打开聚合成PMMA-VAc. PMMA-VAc易于分散在混合碳酸酯溶剂中并形成凝胶, 凝胶粘度随PMMA-VAc浓度的增加而增加, 当浓度为4%时成膜效果最佳. PMMA-VAc膜具有大量的微孔结构, 具有极强的吸液性能. PMMA-VAc膜具有良好的热稳定性: 在380 ℃范围内保持稳定. 聚烯烃膜支撑的PMMA-VAc膜室温下的离子电导率为1.85×10^－3 S•cm^－1, 用作为锂离子电池的聚合物电解质时, 电池具有良好的循环稳定性和倍率性能.     

Influence of solvent type on porosity structure and properties of polymer separator for the Li-ion batteries

Polyethylene-supported polymethyl methacrylate/poly(vinylidene fluoride-co-hexafluoropropylene) separator for gel polymer lithium-ion battery use was prepared with a mixed solvent of n-butanol and acetone. The prepared separator was characterized with scanning electron spectroscopy and X-ray diffraction, and its performance was investigated by electrochemical impedance spectroscopy and battery charge/discharge test. Compared to the separator prepared with acetone, the separator prepared with the mixed solvent shows an enhanced porosity (from 42 to 49 %) and electrolyte uptake (from 104 to 125 %). The ionic conductivity of the corresponding gel polymer electrolyte is improved from 2.81 to 3.39 mS cm^?1, the discharge capacity retention of the LiCoO₂/artificial graphite battery is increased from 95 to 98 % after 100 cycles at 0.5 C, and the discharge capacity of the battery at 1 C increases by 4 %.     

Synthesis and Characterization of a Novel Polymer Electrolyte for Lithium-ion Battery

A novel polymer electrolyte with the formula of Li2B4O7-PVA for lithium-ion battery was synthesized and its ion conductivity and mechanical properties were also tested. It is found that the conductivity of the prepared polymer electrolytes is higher than that of LiClO4/PEO or LiClO4/EC-DMC by two or three orders in magnitude and a large delocalized bond formed in Li2B4O7-PVA lead to transportation of Li ion easier, this electrolyte possesses high thermo-stability and can be used under 200℃.     

Optical and dielectric properties of PVP based composite polymer electrolyte films

Solid polymer electrolyte films were prepared by adding Al₂O₃ particles to poly(vinylpyrrolidone)-MgCl₂ ? 6H₂O salt using solution cast technique. Various analytical techniques have been applied to characterize the prepared polymer films such as XRD, SEM, UV–Vis spectroscopy and AC conductivity. The structural analysis of pure poly(vinylpyrrolidone) complexed with MgCl₂ ? 6H₂O salt showed orthorhombic lattice structure indicating its semi-crystalline nature. SEM analysis reveals the heterogeneous phase of nanocomposite polymer electrolyte systems. The conductivity of Al2O3 doped poly(vinylpyrrolidone) based solid polymer electrolyte was found to be 1.22 × 10^–6 S/cm at room temperature for 85: 15 weight composition. Electrochemical cell has been fabricated with the configuration Mg⁺/(PVP + MgCl₂ ? 6H₂O + Al₂O₃)/(I₂ + C + electrolyte) and its discharge characteristics were studied for a constant load of 100 kΩ. Various cell parameters such as open-circuit voltage, short circuit current, energy density and power density were calculated for the prepared samples.     

聚苯并咪唑-锂盐-聚乙二醇单甲醚共混全固态聚合物电解质的制备及性能

使用共混后浇铸成膜的方法,制备了聚苯并咪唑-锂盐-聚乙二醇单甲醚组成的锂离子电池共混全固态聚合物电解质。通过傅里叶红外光谱(FT-IR)、X射线衍射(XRD)、差示扫描量热(DSC)、拉伸与交流阻抗测试表征了共混全固态电解质的结构与性能。研究了不同锂盐以及各组分含量对共混全固态电解质的力学性能与电导率的影响。结果表明:聚苯并咪唑与聚乙二醇单甲醚之间存在氢键;共混全固态电解质中聚乙二醇单甲醚处于无定形态;锂盐的加入使聚乙二醇单甲醚的玻璃化转变温度下降;聚乙二醇单甲醚含量越高,共混膜强度越低,电导率越高,并且使用三氟甲磺酸锂作为锂盐时其电导率最高,室温下可以达到3.58×10~(-5) S/cm,高温下可以达到3.3×10~(-3) S/cm,高温下满足对锂离子电池的使用需求。     

Influence of additives on the thermal behavior of nickel/metal hydride battery

This study discusses the thermal behavior of the 6.5 Ah cylinder Ni/MH hydride battery with 0.5 wt% ytterbium oxide (Yb₂O₃) in nickel electrode and 1.0 wt% super absorbent polymer (SAP) in hydrogen-storage alloy (MH) electrode during charging to 150% of its rating capacity. Quantity of heat and heat generation rate of the battery during charging are studied by quartz frequency microcalorimeter. Heat generation curve is fitted into a function, and heat transport equation is solved. Using measured data, the internal temperature profiles at the terminal moment of charging at 1C, 3C, and 5C are simulated by FEM. Influence of Yb₂O₃ and SAP on the thermal behavior of Ni/MH battery is examined by the two-dimensional thermal model. Results show that addition of Yb₂O₃ and SAP can achieve substantial improvement for thermal behavior of Ni/MH battery at 1C,3C, and 5C charging.     

MH/Ni电池用稀土系储氢合金的失效及回收研究

探讨了深度过放电对MH／Ni电池负极储氢合金的影响。发现在过放电后，负极储氢合金的XRD结构图中，除了储氢合金的主相外，还出现了十分明显的Al(OH3),La(OH)3的衍射峰。结合各种情况下储氢合金失效的,原因利用化学处理及再熔炼的方法对失效MH／Ni电池的负极粉进行了回收实验，并对比了回收合金与原合金的结构及电化学性能。XRD测试结果表明回收合金与原合金的结构相同，均为CaCu5型。恒电流充放电实验发现，回收合金与原合金粉相比，放电容量接近，放电电位高。不寿命测试结果表明，回收合金较原合金容量衰减更缓慢。     

掺杂NiO的Ni(OH)_2电化学性能研究

于Ni(OH)2中添加具有电容特性和大电流充放电性能良好的NiO.研究发现掺杂5%NiO的Ni(OH)2在0.2C倍率下放电容量可达310.1mAh/g,而3C放电容量还可以保持79.5%.其循环伏安扫描氧化还原峰电位差仅为164mV,表明该材料的循环可逆性好.由此可见在Ni(OH)2掺杂适量的NiO,对于Ni(OH)2的大电流充放电性能确有改进作用.     

PVDF/PAN/SiO<Subscript>2</Subscript> polymer electrolyte membrane prepared by combination of phase inversion and chemical reaction method for lithium ion batteries

PVDF/PAN/SiO₂ polymer electrolyte membranes based on non-woven fabrics were prepared via introducing a chemical reaction into Loeb-Sourirajan (L-S) phase inversion process. It was found that physical properties (porosity, electrolyte uptake and ionic conductivity) and electrochemical properties were obviously improved. A favorable membrane structure with fully connective porous and uniform pore size distribution was obtained. The effects of PVDF/PAN weight ratio on the morphology, crystallinity, porosity, and electrochemical performances of membranes were studied. The optimized PVDF/PAN (70/30 w/w) (designated as M_pc30) polymer electrolyte membrane delivered excellent electrolyte uptake of 246.8 % and the highest ionic conductivity of 3.32 × 10^?3 S/cm with electrochemical stability up to 5.0 V (vs. Li/Li⁺). In terms of cell performance, the Li/M_pc30 polymer electrolyte/LiFePO₄ battery exhibited satisfactory electrochemical properties including high discharge capacity of 149 mAh/g at 0.2 C rate and good discharge performance at different current densities. The promising results reported here clearly indicated that PVDF/PAN/SiO₂ polymer electrolyte membranes prepared by the combination of phase inversion and chemical reaction method were promising enough to be applied in power lithium ion batteries.