MCM-41负载S2O82-/TiO2固体超强酸的制备和酯化性能研究

采用液相沉积法制备了由MCM-41介孔分子筛负载S₂O₈^2-/TiO₂的固体超强酸催化剂。探讨了成酸机理，并以乙酸和异戊醇的酯化反应作为探针反应考察了焙烧温度、浸渍溶液浓度等制备条件对催化剂催化活性的影响，得到了较佳的制备条件。XRD、N₂吸附-脱附和FTIR结果表明，固体超强酸保持了MCM-41的介孔结构，BET表面积高达211 m²·g^-1，且具有强酸性(H_o<-12.70)。     

Cr/MCM-41催化剂的制备及其用于丙烷非氧化脱氢反应

实验分别采用连续吸附法和传统浸渍法制备Cr/MCM-41催化剂（分别记为Cr/MCM-41-ad和Cr/MCM-41-imp）,将制备的Cr/MCM-41催化剂用于丙烷非氧化脱氢制丙烯反应,并对反应过程中的温度、压力、空速等反应条件进行优化,在合适的条件即反应温度为630℃、压力为0.1 MPa、空速为4500 mL·h^-1·g^-1下比较两种方法制备的催化剂在丙烷脱氢制丙烯反应的催化性能.我们采用XRD、SEM-mapping、XPS、UV-vis、H₂-TPR等表征手段对催化剂上α-Cr₂O₃晶体粒径、活性组分及分布等进行表征分析,结果表明Cr/MCM-41-ad和Cr/MCM-41-imp中同时均存在Cr（VI）、Cr（Ⅲ）和α-Cr₂O₃.其中XRD和SEM-Mapping结果可知,Cr/MCM-41-ad上获得的α-Cr₂O₃晶体粒径较小且分散性好;通过UV-vis、XPS和TPR结果证明Cr/MCM-41-imp催化剂存在非活性孤立态Cr（VI）,较难还原,影响其反应活性.相比之下,吸附法制备的催化剂使Cr高分散,可避免形成非活性孤立态Cr（VI）,进而提高丙烷脱氢催化活性.因此,吸附法制备的铬基催化剂用于丙烷脱氢制丙烯有一定的借鉴作用.     

面向异丁烷脱氢介孔γ-Al2O3基催化剂的合成及其高催化性能

采用溶剂蒸发自组装法调控载体形貌及孔道结构,成功制备了有序介孔氧化铝载体。以铬氧物种为活性组分,碱金属钾为助剂,采用浸渍法制备负载型催化剂,用于异丁烷催化脱氢反应,研究了反应温度、原料流速、催化剂粒径等因素对催化性能的影响。采用X射线粉末衍射、透射电子显微镜、N₂物理吸附、氢气程序升温还原及热重等表征方法探讨了载体形貌、孔道结构与催化性能的构效关系,结果表明,低温下有利于控制异丙醇铝的水解和缩合及介孔γ-Al₂O₃的研制。与常规的γ-Al₂O₃相比,所制备的介孔γ-Al₂O₃的有更大的比表面积和良好的有序性,在600℃、101.325kPa、GHSV=1 000 h^-1的条件下,10%（w/w）Cr₂O₃/γ-Al₂O₃催化剂性能最佳,异丁烷的转化率达63.1%,异丁烯的选择性达到85.5%。与传统的催化剂相比,介孔Cr₂O₃/γ-Al₂O₃催化剂具有大的比表面积,高度分散的活性组分,优良的催化性能和良好的抗积碳能力。     

碱土金属对ZrO2-Al2O3及其负载Pd-Rh密偶催化剂的影响

采用胶溶法制备了一系列碱土金属改性的ZrO₂-Al₂O₃, 并以其为载体采用等体积浸渍法制备了Pd-Rh密偶催化剂. 采用低温N₂吸附-脱附、X射线衍射(XRD)、氨气程序升温脱附(NH3-TPD)对载体样品进行了表征. 结果表明, 碱土金属的添加增大了ZrO₂-Al₂O₃的比表面积, Sr-Zr-Al样品经1000 °C焙烧5 h后具有最大的比表面积, 为164 m²·g^-1. 对催化剂进行了H₂程序升温还原(H₂-TPR)、X射线光电子能谱(XPS)和活性表征, 考察了催化剂对C₃H₈的转化活性. 测试结果表明, 添加碱土金属能有效提高催化剂上丙烷的转化活性.     

Ni-Mo氮化物催化剂:合成及其丙烷氨氧化催化性能简

分别采用溶胶-凝胶法、旋转蒸发微波干燥法、共沉淀法、浸渍法和机械混合法制备Ni-Mo氧化物前驱体. 以H₂和N₂的混合气为氮化气体,采用程序升温氮化法合成了镍钼氮化物催化剂. 利用X射线衍射、总氮含量分析、X射线光电子能谱及H₂程序升温还原对Ni-Mo氧化物前体及氮化物催化剂进行了表征. 将上述Ni-Mo氮化物催化剂用于丙烷氨氧化反应中. 结果表明,Ni-Mo氧化物前驱体的制备方法影响其氮化物催化剂上丙烷氨氧化反应性能. Ni-Mo氮化物催化剂中氮物种的移动性及反应性对产物丙烯腈选择性的影响较大,共沉淀法制备的催化剂存在大量的活性氮物种,因而具有良好的催化丙烷氨氧化反应活性.     

SBA-15负载高分散纳米NiO的丙烷氧化脱氢制丙烯催化性能

采用浸渍法通过改变焙烧气氛制备了系列NiO/SBA-15 (w_NiO=20%)催化剂, 并考察了催化剂的丙烷氧化脱氢(ODHP)反应性能. 实验结果表明, 与在静止和流动空气中焙烧的催化剂相比, 在1%NO/He (V_NO/V_He=1:99)气氛中焙烧的NiO/SBA-15-NO具有优异的低温丙烷氧化脱氢制丙烯性能, 在350 ℃时, 丙烷的转化率和丙烯收率分别约达29%和13%. 反应温度升至450 ℃时, 丙烯的选择性仍保持在45%左右. X射线粉末衍射(XRD)和透射电镜(TEM)测试结果表明, 1%NO/He气氛可有效抑制焙烧过程中NiO纳米颗粒的团聚, 使NiO物种高分散于SBA-15 的孔道中. H₂-程序升温还原(H₂-TPR)和O₂-程序升温脱附(O₂-TPD)测试结果表明, 随着NiO在SBA-15上分散度的提高, 催化剂的抗还原性增强, ODHP活性氧物种O-的含量增加, 进而使1%NO/He气氛中焙烧的NiO/SBA-15-NO在较宽的温度范围内(350-450 ℃)均具有良好的丙烯选择性, 并显著提高了催化剂的低温活性.     

沉淀剂和Ag含量变化对甲醛降解性能的影响

采用不同沉淀剂制备CeO₂-Co₃O₄复合金属氧化物载体,通过浸渍负载不同含量Ag获得Ag/CeO₂-Co₃O₄催化剂.借助氮气物理吸附、XRD、Raman和H₂-TPR等手段研究了催化剂的物理化学性质.结果表明：当WHSV=30 000 mL·g^-1·h^-1时,催化剂能表现出良好的催化氧化甲醛性能,在≤ 90℃时实现甲醛的完全转化.草酸沉淀能有效降低Ce-Co氧化物的结晶度,使得Co²⁺含量增加,提供更多的氧空位,促进了氧分子的活化与迁移,从而提高了催化活性.随着Ag含量增加,使得由草酸沉淀制备的Ag/CeO₂-Co₃O₄催化剂的活性增强,且金属与载体间的相互作用也增强,当Ag负载量为1%（重量百分比）时活性最佳.     

制备参数对高比表面积介孔催化剂La-Co-Zr-O结构与性能的影响

采用双表面活性剂模板(十六烷基三甲基溴化铵和聚乙二醇辛基苯基醚的混合物)分解法制备了不同原子比(n_La+n_Co)/(n_La+n_Co+n_Zr)和不同温度焙烧的系列介孔混合氧化物催化剂La-Co-Zr-O。运用XRD、N₂吸附/脱附、XPS和H₂-TPR等技术对催化剂进行了表征，并以CO和C₃H₈氧化为模型反应，考察了组分配比和焙烧温度等参数对催化剂催化性能的影响。比表面积和孔径测试结果表明，样品具有很高的比表面积(108～266 m²·g^-1)和分布集中的孔径(3.4～3.9 nm)，Zr含量较高的样品比表面积较大。XRD结果表明，样品中的活性组分钴物种主要以Co₃O₄形式存在；XPS和H₂-TPR结果表明，样品中可还原的晶格氧的数量、活动度以及表面钴原子浓度均与催化剂对CO和C₃H₈的氧化性能密切相关。原子比为0.5的样品中，较多的晶格氧易于在相对低温下还原；而原子比为0.7的样品表面钴原子浓度较高，这使得两样品均表现出较高的催化活性。经650 ℃焙烧的样品仍保持较高的比表面积(108 m²·g^-1)和分布集中的介孔孔径(最可几孔径约3.8 nm)，且催化活性下降幅度也很小，表明该系列介孔催化剂具有优良的抗烧结能力和介孔热稳定性。     

介孔氧化铝负载钒催化剂上丙烷氧化脱氢制丙烯

 采用浸渍法制备了介孔氧化铝 (m-Al2O3) 负载钒催化剂 (V/m-Al2O3), 并考察了其催化丙烷氧化脱氢制丙烯反应活性. 通过 N2 吸附-脱附、透射电镜、X 射线粉末衍射、紫外-可见漫反射光谱、氢-程序升温还原和氨-程序升温脱附对催化剂进行了表征. 结果表明, 介孔氧化铝具有大比表面积、窄孔径分布和两维六方相结构, 在其上负载适量的 V 可实现 V 活性物种的高分散及催化剂的弱酸性, 从而有利于提高丙烷转化率和丙烯选择性. 与共合成法制备的含 V 介孔氧化铝 V/m-Al2O3(C) 和浸渍法制备的 V/?-Al2O3 相比, V/m-Al2O3 表现出更高的催化活性. 这与载体较弱的酸性和较大的比表面积以及 V 物种的高分散有关.     

铈钛混合氧化物负载磷钨酸吸附-分解NOx性能

通过软化学途径合成了铈钛混合氧化物(CeO₂-TiO₂)载体材料, 并分别通过等体积浸渍法和机械研磨法负载磷钨酸(H₃PW₁₂O₄₀)。采用FTIR、XRD、SEM和BET比表面积测定对CeO₂-TiO₂及负载型多酸催化剂进行了表征;考察了负载量、负载方法、吸附温度等因素对催化剂吸附NO_x效率的影响;选取吸附性能最佳的催化剂进行了NO_x催化分解实验, 探讨了NO_x吸附-分解机理。结果表明:相对于等体积浸渍法, 机械研磨法更适合此类载体负载H₃PW₁₂O₄₀, 其NO_x吸附效率均高于H₃PW₁₂O₄₀及载体本身;在0~60%的负载量范围内, 随着H₃PW₁₂O₄₀负载量的增加, 负载型催化剂吸附NO_x的效率呈上升趋势, 负载量为40%时NO_x吸附效率最佳, 达90%;吸附过程中NO_x与催化剂活性组分H₃PW₁₂O₄₀发生作用, 生成NOH⁺, H₃PW₁₂O₄₀二级结构中结晶水对催化剂吸附NO_x有重要作用;当温度从150℃升至 450℃时, 被吸附的NO_x发生分解, 分解产物的组成与N₂的收率均受升温速率的影响, 升温速率越快, N₂收率越高。向吸附分解NO_x后的催化剂床层通入含有水蒸气的空气, 可有效补充NO_x分解过程中H₃PW₁₂O₄₀失去的结晶水, 从而恢复催化剂优良的NO_x吸附分解性能, 实现催化剂的有效再生利用。     

负载Ni催化剂用于乙二醇蒸汽重整制氢催化性能研究

采用等体积浸渍法和共沉淀法制备了Ni催化剂,在固定床反应器上考察了Ni负载量、焙烧温度、反应温度等因素对乙二醇低温重整制氢反应活性和选择性的影响。应用X射线衍射、氮物理吸附、H₂程序升温还原等技术对负载型Ni催化剂进行了表征。结果表明,共沉淀法制备的Ni/CeO₂催化剂具有较小的NiO颗粒与CeO₂载体颗粒粒径,催化活性较高。添加少量氧化钴到Ni/CeO₂催化剂中可使H₂收率达72.6%,EG转化率达93.1%。在CeO₂中添加Al₂O₃能提高负载Ni催化剂的活性,乙二醇转化率达94.0%,H₂收率达67.0%;但添加SiO₂则使其活性明显变差。     

Nanostructured CoMoO4 Supported on Mesoporous SBA-15 for Catalytic Oxidative Dehydrogenation of Propane to Propene

Nanostructured cobalt molybdate catalysts supported on mesoporous silica SBA-15 with different loadings were prepared by citric acid coordination-impregnation method and characterized by XRD, TEM, and BET techniques. The characterization results showed that high loading of well-dispersed crystalline CoMoO₄ may be achieved using citric acid coordination-impregnation method and the mesoporous structure of the support remained intact. The catalytic activity of these catalysts in the oxidative dehydrogenation of propane was investigated. The catalysts of nanostructured cobalt molybdate supported on mesoporous silica SBA-15 showed better catalytic performance than the corresponding bulk composite oxide and nanostructured CoMoO₄ supported on SBA-15 with loading of 13% (mass fraction, w) displayed propene yield of 16.8% at 823 K.     

铝硼复合氧化物负载Pt-Sn催化剂的丙烷脱氢性能研究

采用蒸发自组装法制备铝硼复合氧化物((AlB_x)_2O_3),真空配合浸渍法制备PtSn双金属催化剂,并应用于丙烷脱氢制丙烯.采用N_2物理吸附、 SEM、 TEM、 XRD、 H_2-TPR、 NH_3-TPD、 TG和ICP-OES对催化剂进行表征.掺入B可大幅增加载体的总酸量和酸中心密度,降低酸强度.当B掺入量为Al的10%时, Cat-AB_(0.1)的总酸量是Cat-AB_0总酸量的2.45倍,且只有弱酸中心.当B掺入量为Al的50%时, Cat-AB_(0.5)的酸中心密度是Cat-AB_0的4.3倍.以铝硼复合氧化物负载的催化剂均优于纯氧化铝负载的催化剂,催化剂的脱氢活性和稳定性与载体的硼铝摩尔比之间存在如下规律:AB_(0.1)AB_(0.3)AB_(0.5)AB_0.     

Preparation and characterization of supports with a synthesized layer of catalytic filamentous carbon: III. Synthesis of carbon nanofibers on nickel supported onto aluminum oxide

The synthesis of catalytic filamentous carbon (CFC) on catalysts prepared by supporting Ni²⁺ compounds onto the surface of various alumina modifications (macroporous α-Al₂O₃ and mesoporous ?-Al₂O₃ and δ-Al₂O₃) using two procedures (impregnation and homogeneous precipitation) was studied. The texture characteristics (specific surface area and pore structure) of the parent supports and adsorbents with a CFC layer were compared. The effect of the supporting procedure on the surface morphology of Ni/Al₂O₃ catalysts and the synthesized CFC layer was studied by scanning electron microscopy. It was found that the carbon yield on a macroporous catalyst prepared by homogeneous precipitation was higher than that on a catalyst prepared by impregnation by a factor of ～2. The CFC layer exhibited a mesoporous structure because of a chaotic interlacing of carbon nanofibers, and the synthesis of CFC on macroporous supports resulted in the formation of a bidisperse pore structure of the adsorbent. Active and stable heterogeneous biocatalysts were prepared by the adsorptive immobilization of enzymatically active substances (glucoamylase and nongrowing baker’s yeast cells) on CFC.     

Investigation of CO and formaldehyde oxidation over mesoporous Ag/Co3O4 catalysts

CO and formaldehyde (HCHO) oxidation reactions were investigated over mesoporous Ag/Co₃O₄ catalysts prepared by one-pot (OP) and impregnation (IM) methods. It was found that the one-pot method was superior to the impregnation method for synthesizing Ag/Co₃O₄ catalysts with high activity for both reactions. It was also found that the catalytic behavior of mesoporous Co₃O₄ and Ag/Co₃O₄ catalysts for the both reactions was different. And the addition of silver on mesoporous Co₃O₄ did not always enhance the catalytic activity of final catalyst for CO oxidation at room temperature (20 °C), but could significantly improve the catalytic activity of final catalyst for HCHO oxidation at low temperature (90 °C). The high surface area, uniform pore structure and the pretty good dispersion degree of the silver particle should be responsible for the excellent low-temperature CO oxidation activity. However, for HCHO oxidation, the addition of silver played an important role in the activity enhancement. And the silver particle size and the reducibility of Co₃O₄ should be indispensable for the high activity of HCHO oxidation at low temperature.     

Isobutane dehydrogenation over chromia alumina catalysts prepared from MIL-101: Insight into chromium species on activity and selectivity

Various mesoporous chromia alumina catalysts were prepared by five different methods based on a metal-organic framework MIL-101 and their catalytic performances over isobutane dehydrogenation were investigated. The highly dispersed chromium species were produced on catalyst KCr Al-I1 with largest specific surface area of 198 m2 g-1prepared with aluminium isopropoxide(Al(i-OC3H7)3) by ultrasonic impregnation method. However, the catalyst KCr Al-I2 synthesized by stirring impregnation possessed crystalline α-Cr2O3 phase, which was poorly dispersed. Two types of Cr-rich and Al-rich Crx Al2-xO3 solid solutions, designated as Cr Al-I and Cr Al-II phase, were formed over the catalysts KCr Al-I3(prepared by Al(i-OC3H7)3with nitric acid regulation), KCr Al-C4(prepared by aluminium chloride hexahydrate) and KCr Al-N5(prepared by aluminium nitrate nonahydrate). Catalytic evaluation results revealed that KCr Al-I1 exhibited the high isobutane conversion due to its highly dispersed chromium species. However, KCr Al-I3, KCr Al-C4 and KCr Al-N5 showed the higher isobutene selectivity(95.2%-96.4%) on account of the formation of chromia alumina solid solutions in the catalysts. Moreover, the solid solution over the chromia alumina catalysts could greatly suppress the coke formation.     

介孔Al2O3负载PdO催化甲烷燃烧反应性能

采用浸渍法制备了介孔Al2O3(M-Al2O3)负载PdO催化剂,考察了其催化CH4燃烧反应性能.结果表明,以M-Al2O3为载体的PdO催化剂活性比普通Al2O3载体高得多,这很可能与M-Al2O3的孔道结构对PdO物种的限域作用有关.随着PdO/M-Al2O3催化剂焙烧温度的升高,甲烷催化燃烧活性先增加后降低,其中700oC焙烧的催化剂活性最高,400oC反应时CH4转化率为91%.此时Pd物种主要以PdO颗粒形式高度分散在载体的介孔孔道内,而高温焙烧时,Pd物种主要以Pd和PdO的混合晶相存在.尽管900oC焙烧制得的催化剂上CH4的转化率降低,但TOF值最大,这可能与该催化剂中同时存在金属Pd和PdO有关.     

The Dehydrogenation of Propane on Platinum–Tin Glass-Fiber Woven Catalysts

The reaction of propane dehydrogenation on platinum–tin catalysts supported onto different woven carriers (an aluminoborosilicate and two silica materials) was studied. It was found that the catalyst was rapidly deactivated by carbon deposits formed, and the rate of this reaction increased with the specific surface area of the glass-fiber woven material and the Pt content. It was established that the Pt: Sn ratio in surface platinum particles was about 6, and it increased to 39 after the reaction; this fact is indicative of a Sn loss, which led to an increase in the conversion of feed into carbon deposits that deactivated the catalyst. A mixture of propane and 5–10 vol % H₂ should be used for the stabilization of the catalytic system; in this case, the negative effect of hydrogen on the yield of propylene was minimal. On the catalyst supported onto a silica carrier under optimum conditions (550°C; propane space velocity, 480 h^–1), which correspond to minimum selectivity for the formation of carbon deposits, the yield of propylene was ~18%. The test glass-fiber woven catalyst was inferior to granulated platinum–tin catalysts in terms of catalytic activity; therefore, its use in the reaction of propane dehydrogenation is inexpedient.     

Supported MgO–V<Subscript>2</Subscript>O<Subscript>5</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts for oxidative propane dehydration: Effect of the molar Mg : V ratio on the phase composition and catalytic properties of samples

The physicochemical properties of V₂O₅/Al₂O₃ and MgO–V₂O₅/Al₂O₃ supported catalysts (Mg : V = 1 : 1, 2 : 1, and 3 : 2) obtained by consecutive impregnation of the support with solutions of vanadium and magnesium precursors are studied using a complex of mutually complementary methods (XRD, Raman spectroscopy, UV–Vis spectrometry, and TPR-H₂). The effect of the formation of surface magnesium vanadates of various composition and structure on the catalytic properties of the supported vanadium oxide catalysts in the oxidative dehydrogenation of propane is studied. The introduction of magnesium in the samples and an increase in its content, accompanied by a change in the structure of the surface vanadium oxide phases from polymeric VO₆/VO₅ species to surface metavanadate species, magnesium metavanadate, and further to magnesium divanadate, significantly affects their catalytic properties in the reaction of the oxidative dehydrogenation of propane to propylene.     

Clay-Supported Molybdenum-Based Catalysts for Higher Alcohol Synthesis from Syngas

A kind of clay-supported K-Co-Mo catalyst was prepared by a sol-gel method combined with incipient wetness impregnation. The catalyst structure was characterized by X-ray diffraction, N₂ adsorption-desorption, H₂ temperature-programmed reduction, and X-ray photoelectron spectroscopy techniques and its catalytic performance for higher alcohol syn-thesis from syngas was investigated. The active components has a high dispersion on the clay support surface. The increase of the Mo loading promoted reduction of M⁶⁺ but had no signi cant in fluence on the reduction of Mo⁴⁺ and Co²⁺ species. After reduction, a kind of lower state Mo^δ+ (1<δ<4) species was observed on the surface. Compared with the unsupported catalyst, the clay supported K-Co-Mo catalysts showed much higher catalytic performance for alcohol formation. The reason can be explained that the supported catalyst have a high active surface area and the mesoporous structure prolonged the residence time of intermediates for alcohol formation to some extent, which promoted the formation of higher alcohols. The high activity of the catalyst reduced at 773 K may be attributed to the high content of Mo^δ+ (1<δ<4) species on the surface, which was regarded as the active site for the adsorption of nondissociative CO and responsible for the alcohol formation.