The separation of arsenic species in soils and plant tissues by anion-exchange chromatography with inductively coupled mass spectrometry using various mobile phases

Anion-exchange chromatography (Hamilton, PRP-X100) with inductively coupled plasma mass spectrometry (ICP-MS) is commonly used for the speciation of arsenic in environmental and biological samples. However, retentions for As species are frequently different because of the use of widely different mobile phases. In addition, chloride in matrices interferes with arsenic determination. In this study, we systematically investigated various mobile phases based on ammonium salts affecting arsenic retention to eliminate chloride interference chromatographically. Hence, various mobile phases based on ammonium salts, including NH₄H₂PO₄, NH₄HPO₄, NH₄Ac, NH₄HCO₃ and NH₄NO₃, were examined for reasonable resolution and to separate chloride from arsenic species. The best result was obtained with a mobile phase containing 30 mM NH₄H₂PO₄ at pH 5.6, where the separation of arsenic species, including arsenite [As(III)], arsenate [As(V)], dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA)], was achieved within 9 minutes with reasonable resolution and free of chloride interference at its high level (500 mg L^− 1). The detection limits for the arsenic species were in the range of 0.1-0.3 μg L^− 1 with a direct injection of sample without removing matrix. Finally, the proposed method was used for the determination of arsenic species in contaminated soil and plant tissues.     

Determination of arsenite, arsenate, and monomethylarsonic acid in seawater by ion-exclusion chromatography combined with inductively coupled plasma mass spectrometry using reaction cell and hydride generation techniques

This paper describes a robust and sensitive method for the determination of arsenic species in seawater by ion-exclusion liquid chromatography (LC) combined with inductively coupled plasma mass spectrometry (ICP-MS) using reaction cell and hydride generation (HG) techniques. A good separation of arsenite, arsenate, and monomethylarsonic acid was achieved using an ion-exclusion column packed with a sulfonated polystyrene resin and a dilute nitric acid at pH 2.0 as the eluent, even when a large volume, i.e. 200 mul, of seawater samples containing a large amount of matrix was repeatedly injected. Separations of the chloride ion due to the matrix and arsenic species were partially performed; however, the extensive peak of ArCl due to high content of Cl(-) in a sample overlapped peaks of the three arsenic species on (75)As measurement by ICP-MS. This ArCl polyatomic interference was efficiently eliminated by collision of ArCl molecules with helium in an octopole reaction cell which was introduced prior to a mass spectrometer. Detection limits of the three arsenic species in a sample containing 2% Cl(-), the concentration of which is comparable to that in a seawater sample, by LC-ICP-MS with the octopole reaction system (ORS), ranged from 21 to 25 pg As ml(-1); these values were three-six times lower than those by LC-ICP-MS without ORS. As another technique for ArCl interference elimination, HG prior to ICP-MS was also successfully used not only to reduce the interference but also to improve the detection limits to 3.4-4.5 pg As ml(-1). The developed LC-ICP-ORS-MS and LC-HG-ICP-MS were validated by analyzing a certified reference material (CRM) of seawater. In addition, no serious decrease in analytical performance of present methods was observed in the experimental periods of half a year for LC-ICP-ORS-MS and 1 year for LC-HG-ICP-MS, respectively. The latter method was successfully applied to characterize seasonal variations of three arsenic species in deep seawater and surface seawater.     

Elimination of the chloride interference on the determination of arsenic using hydride generation inductively coupled plasma mass spectrometry.

In the determination of arsenic, attention has recently focused on the speciation of As(III) and As(V). Reversed-phase HPLC can be used to efficiently separate these two arsenic species. When inductively coupled plasma mass spectrometry is used for arsenic detection, an isobaric interference at m/z 75 is caused by the presence of chloride in the sample. These experiments describe the use of hydride generation in conjunction with a polypropylene-membrane gas-liquid separator to completely eliminate the transport of chloride to the plasma. A detection limit of 0.46 ppb for As(III) was achieved with this system. The chromatographic resolution of the system was not compromised by the addition of the gas-liquid separator. A determination of the arsenic content of a NIST urine sample was performed to demonstrate the effectiveness of the chloride elimination.     

Speciation and instrumental neutron activation analysis for arsenic in water samples

Ground water samples obtained from West Bengal, India were analyzed for total arsenic and its inorganic species contents by instrumental neutron activation analysis (INAA). Two anion exchange separation methods using Dowex 1X8 in chloride and acetate forms were standardized for the speciation of As(III) and As(V) using radiotracers. The method by Dowex 1X8 in the acetate form was validated using synthetic mixtures of As(III) and As(V), and applied to water samples; the species concentrations were determined by INAA. The accuracy of the INAA method was evaluated by analyzing the NRCC CRM DORM-2 for total arsenic.     

Substoichiometric speciation for inorganic arsenic and methylated arsenic and its application to samples of marine organisms

A substoichiometric isotope-dilution method is described for the determination of monomethylarsonate, MeAs(V), and dimethylarsinate, Me₂As(V). After the separation of MeAs(V) and Me₂As(V) by extraction as their iodides into benzene, these methylated arsenic species are complexed with a substoichiometric amount of diethyldithiocarbamate in benzene, and the uncomplexed methylarsenic species are removed. The relative standard deviations for the substoichiometric extraction of MeAs(V) and Me₂As(V) are 0.55% and 1.1%, respectively. This substoichiometric speciation of methylated arsenic together with an earlier substoichiometric method for speciation of inorganic arsenic species was applied to the speciation of arsenic in an acid-digested solution of a macro-algae sample. It was demonstrated that almost all the arsenic in this solution was Me₂As(V) even after the digestion with nitric acid.     

Multielemental determination of arsenic, selenium and chromium(VI) species in water by high-performance liquid chromatography-inductively coupled plasma mass spectrometry

A new method for the simultaneous chromatographic separation and determination of arsenite, arsenate, mono-methylarsonic acid, dimethylarsinic acid, selenite, selenate and hexavalent chromium in water is presented. Speciation was achieved by on-line coupling of anion-exchange LC and inductively coupled plasma mass spectrometry (ICP-MS). Optimisation of the chromatographic conditions led to baseline separation of the seven species in 14 min using gradient elution with NH4NO3 20 mM, pH 8.7-NH4NO3 60 mM, pH 8.7 as mobile phase. Detection limits are in the range 40-60 ng l(-1) for arsenic species, around 130 ng l(-1) for Cr(VI), and higher for Se(IV) and Se(VI) (1.2 and 1.4 microg l(-1) respectively). The method showed good accuracy and repeatability, and no interference of chloride on 75As, 77Se or 53Cr was observed. The developed method was applied to the analysis of several environmental surface water samples.     

Application of central composite designs for optimisation of the chromatographic separation of monomethylarsonate and dimethylarsinate and of selenomethionine and selenite by ion-pair chromatography coupled with plasma mass spectrometric detection

Central composite designs (CCDs) were used in the study of the ion-pair chromatographic separation of arsenic and selenium species in tap water: monomethylarsonate, dimethylarsinate, selenomethionine and selenite. The ternary eluent consisted of tetrabutylammonium phosphate (TBA), sodium hydrogenphosphate (Na2HPO4) and 1% acetonitrile. CCD allowed the investigation of the influence of the eluent parameters, which varied from 0.5 to 4.2 mmol l-1 Na2HPO4, 0.5 to 4.2 mmol l-1 TBA and pH 4.9 to 8.2, on the capacity factors (k') of arsenic and selenium compounds. Furthermore, another mathematical model that permitted the variation of the chromatographic selectivity of species, computed from their retention data to be followed, was investigated. This showed the ability to locate the optimum conditions within the experimental design, so that arsenic and selenium species could be simultaneously quantified with good efficiency and resolution. A comparison between the predicted and the experimental response values was made in order to assess the prediction quality of the model. Response surfaces and isoresponse curves obtained from the mathematical models allowed the determination of the optimum chromatographic conditions and the robustness of the method. The predicted optimum zone allowing satisfactory determination of both arsenic and selenium compounds was pH 5.5-6.5, 2.5 mmol l-1 Na2HPO4 and 3.0-4.0 mmol l-1 TBA.     

毛细管电泳-电感耦合等离子体质谱法测定藻类中6种不同形态的砷化合物

建立了一种利用毛细管电泳与电感耦合等离子体质谱联用技术(CE-ICP-MS)分析检测6种不同形态砷化合物的方法。详细研究了缓冲溶液的种类、pH值和浓度,分离电压以及进样时间等因素对6种砷化合物的分离度、灵敏度和重现性等的影响。结果表明,在最佳条件下,三价砷(As3+)、一甲基砷(MMA)、二甲基砷(DMA)、五价砷(As5+)、砷胆碱(AsC)和砷甜菜碱(AsB)6种化合物在25 min内得到完全分离。6次平行测定中,6种砷化合物峰面积的相对标准偏差(RSD)为3%～5%,检出限(以As计)(3倍信噪比)为0.08～0.12 μg/L。应用该方法成功地对海带中6种砷化合物进行了分析,回收率为90%～103%。该方法具有耗时短、灵敏度高、样品消耗量少、稳定性好等优点,可用于藻类样品中不同形态砷化合物的分析。     

液相色谱-双通道原子荧光检测联用法同时测定砷和硒的形态

建立了一种利用高效液相色谱-双通道原子荧光检测联用同时进行砷和硒形态分析的方法。以10 mmol/L NH4H2PO4溶液(pH 5.6)(添加2.5%(体积分数)的甲醇)为流动相,在12 min内同时分离了三价砷(As(III))、一甲基砷(MMA)、二甲基砷(DMA)、五价砷(As(V))、硒代胱氨酸(SeCys)、硒代蛋氨酸(SeMet)和四价硒［Se(IV)］等化合物。As(III)、DMA、MMA、As(V)、SeCys、SeMet和Se(IV)的检出限分别为1,3,2,3,4,18和3 μg/L (进样量为200 μL),5次测定的相对标准偏差为1.9%～6.1%(As 100 μg/L, Se 300 μg/L)。应用该方法对人体尿样及硒酵母片中砷和硒的形态进行了分析,目标物在尿样中的加标回收率为83%～108%,在硒酵母片中的加标回收率为88%～105%。实验结果表明,该方法可用于尿样及药品中砷和硒形态的日常分析。该方法减少了样品的分析时间和试剂用量,降低了工作强度,提高了工作效率。     

Separation of arsenic species by capillary electrophoresis with sample-stacking techniques

A simple capillary zone electrophoresis procedure was developed for the separation of arsenic species (AsO(2)(2-), AsO(4)(2-), and dimethylarsinic acid, DMA). Both counter-electroosmotic and co-electroosmotic (EOF) modes were investigated for the separation of arsenic species with direct UV detection at 185 nm using 20 mmol L(-1) sodium phosphate as the electrolyte. The separation selectivity mainly depends on the separation modes and electrolyte pH. Inorganic anions (Cl(-), NO(2)(-), NO(3)(-) and SO(4)(2-)) presented in real samples did not interfere with arsenic speciation in either separation mode. To improve the detection limits, sample-stacking techniques, including large-volume sample stacking (LVSS) and field-amplified sample injection (FASI), were investigated for the preconcentration of As species in co-CZE mode. Less than 1 micromol L(-1) of detection limits for As species were achieved using FASI. The proposed method was demonstrated for the separation and detection of As species in water.     

Elimination of chloride interference on arsenic speciation in ion chromatography inductively coupled mass spectrometry using an octopole collision/reaction system

Anion-exchange chromatography with inductively coupled plasma mass spectrometry (ICP-MS) is often used for the speciation of arsenic (As). In this work, either He or H₂ was introduced to the octopole collision/reaction cell to eliminate chloride (Cl⁻) interferences during As speciation by ICP-MS. Polyatomic species, ⁴⁰Ar³⁵Cl and ³⁸Ar³⁷Cl, which are formed in high chloride matrices interfere with the ICP-MS detection of ⁷⁵As. These interferences were reduced or eliminated by introducing He or H₂ to the collision/reaction cell, with some loss in sensitivity when compared to the standard mode (no gas). For example, the sensitivity of As(V) was 30.4 and 17.7% of that observed in standard mode when introducing He and H₂, respectively. Chloride interference was completely eliminated using a flow rate of 3.0 mL min^− 1 with H₂ as a reaction gas with detection limits in the range of 0.3-0.6 μg L^− 1. The developed method was applied to determination of arsenic species in waters containing high concentrations of chloride by following a simple procedure and without modification of the ICP-MS instrument.     

Coupled high performance liquid chromatography-microwave digestion-hydride generation-atomic absorption spectrometry for inorganic and organic arsenic speciation in fish tissue

A high performance liquid chromatography-microwave digestion-hydride generation-atomic absorption spectrometry (HPLC-MW-HG-AAS) coupled method is described for As(III), As(V), monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), arsenobetaine (AsB) and arsenocholine (AsC) determination. A Hamilton PRP-X100 anion-exchange column is used for carrying out the arsenic species separation. As mobile phase 17 mM phosphate buffer (pH 6.0) is used for As(III), As(V), MMA and DMA separation, and ultrapure water (pH 6.0) for AsB and AsC separation. Prior to injection into the HPLC system AsB and AsC are isolated from the other arsenic species using a Waters Accell Plus QMA cartridge. A microwave digestion with K(2)S(2)O(8) as oxidizing agent is used for enhancing the efficiency of conversion of AsB and AsC into arsenate. Detection limits achieved were between 0.3 and 1.1 ng for all species. The method was applied to arsenic speciation in fish samples.     

Inorganic and Organic Arsenic Speciation in Seawaters by IEC-HG-AAS

Abstract

Arsenic (III), arsenic (V), monomethylarsonic acid (MMA), and dimethylarsinic acid (DMA) were separated by ion-exchange chromatography. The elution sequence was as follows: 1.5 M ammonia followed by 0.12 M hydrochloric acid yielding As(III) 1 M hydrochloric acid followed by water yielding first As(V) and then MMA. Detection was by hydride generation-atomic absorption spectrometry. No interference was noted from 13 metallic ions.

The method provides a good linearity, precision, accuracy, and sensitivity. It has been applied to the speciation of arsenic in seawaters from the North West coast of Spain (1200 Km).     

CZE for the speciation of arsenic in aqueous soil extracts

We developed two separation methods using CZE with UV detection for the determination of the most common inorganic and methylated arsenic species and some phenylarsenic compounds. Based on the separation method for anions using hydrodynamic sample injection the detection limits were 0.52, 0.25, 0.27, 0.12, 0.37, 0.6, 0.6, 1.2 and 1.0 mg As/L for phenylarsine oxide (PAO), p-aminophenylarsonic acid (p-APAA), o-aminophenylarsonic (o-APAA), phenylarsonic acid (PAA), 4-hydroxy-3-nitrobenzenearsonic acid (roxarsone), monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), arsenite or arsenious acid (As(III)) and arsenate (As(V)), respectively. These detection limits were improved by large-volume sample stacking with polarity switching to 32, 28, 14, 42, 22, 27, 26 and 27 microg As/L for p-APAA, o-APAA, PAA, roxarsone, MMA, DMA, As(III) and As(V), respectively. We have applied both methods to the analysis of the arsenic species distribution in aqueous soil extracts. The identification of the arsenic species was validated by means of both standard addition and comparison with standard UV spectra. The comparison of the arsenic species concentrations in the extracts determined by CZE with the total arsenic concentrations measured by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) indicated that CZE is suited for the speciation of arsenic in environmental samples with a high arsenic content. The extraction yield of phenylarsenic compounds from soil was derived from the arsenic concentrations of the aqueous soil extracts and the total arsenic content of the soil determined by ICP-AES after microwave digestion. We found that 6-32% of the total amount of arsenic in the soil was extractable by a one-step extraction with water in dependence on the type of arsenic species.     

Speciation of arsenic in chicken meat by anion-exchange liquid chromatography with inductively coupled plasma-mass spectrometry

A method was developed for speciation analysis of arsenic in chicken meat. Different procedures were optimized for the recovery of arsenic compounds without destroying the original compounds, and 2 anion-exchange liquid chromatography columns were compared for the separation of arsenic species prior to on-line detection by inductively coupled plasma-mass spectrometry. The 2 species found were dimethylarsinic acid (106 +/- 5 ng/g) and arsenobetaine (37 +/- 4 ng/g). The stability of arsenic species in a chicken meat candidate reference material for at least 12 months was demonstrated.     

Determination of arsenite,arsenate, monomethylarsonic acid and dimethylarsinic acid in cereals by hydride generation atomic fluorescence spectrometry

A fast, sensitive and simple non-chromatographic analytical method was developed for the speciation analysis of toxic arsenic species in cereal samples, namely rice and wheat semolina. An ultrasound-assisted extraction of the toxic arsenic species was performed with 1 mol L^− 1 H₃PO₄ and 0.1% (m/v) Triton XT-114. After extraction, As(III), As(V), dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA) concentrations were determined by hydride generation atomic fluorescence spectrometry using a series of proportional equations corresponding to four different experimental reduction conditions. The detection limits of the method were 1.3, 0.9, 1.5 and 0.6 ng g^− 1 for As(III), As(V), DMA and MMA, respectively, expressed in terms of sample dry weight. Recoveries were always greater than 90%, and no species interconversion occurred. The speciation analysis of a rice flour reference material certified for total arsenic led to coherent results, which were also in agreement with other speciation studies made on the same certified reference material.     

Speciation determination of arsenic in urine by high-performance liquid chromatography-hydride generation atomic absorption spectrometry with on-line ultraviolet photooxidation

A coupled system for arsenic speciation determination based on high-performance liquid chromatography (HPLC), on-line UV photooxidation and continuous-flow hydride generation atomic absorption spectrometry (HGAAS) was built from commercially available modules with minor modifications to the electronic interface, the software and the gas-liquid separator. The best results were obtained with strong anion-exchange columns, Hamilton PRP X-100 and Supelcosil SAX 1, and gradient elution with phosphate buffers containing KH2PO4-K2HPO4. The on-line UV photooxidation with alkaline peroxodisulfate, 4% m/v K2S2O8-1 mol l-1 NaOH, in a PTFE knotted reactor for 93 s ensures the transformation of inorganic AsIII, monomethylarsonate, dimethylarsinate, arsenobetaine, arsenocholine, trimethylarsine oxide and tetramethylarsonium ion to arsenate. About 32-36 HPLC-UV-HGAAS runs could be performed within 8 h, with limits of detection between 2 and 6 micrograms l-1 As, depending on the species. The method was applied to the analysis of spot urine samples and certified urine reference materials (CRMs). Upon storage at 4 degrees C, reconstituted CRMs are stable for at least 2 weeks with respect to both their total arsenic content and the individual species distribution.     

微波辅助提取-液相色谱-氢化物发生-原子荧光光谱法分析沉积物中砷的形态

采用微波辅助提取-液相色谱-氢化物发生-原子荧光光谱法(LC-HG-AFS)联用技术分析了太湖沉积物中砷的形态[亚砷酸(As(III))、二甲基砷酸钠(DMA)、一甲基砷酸二钠(MMA)和砷酸As(V)]。测得沉积物中以无机砷为主,且以As(V)居多。选定以1mol/L的磷酸和0.1mol/L抗坏血酸为提取液,在微波辅助萃取(功率为60W,时间12min)下,萃取率达79.84%～91.57%,回收率在94.78%～107.6%之间。4种砷的形态在0～160μg/L之间时线性良好,检测限为0.6～2.3μg/L,相对标准偏差RSD为1.62%～2.20%。方法具有简便、快速、灵敏的特点。     

Separation and determination of arsenic species in water by selective exchange and hybrid resins

A simple and efficient method for separation and determination of inorganic arsenic (iAs) and organic arsenic (oAs) in drinking, natural and wastewater was developed. If arsenic is present in water prevailing forms are inorganic acids of As(III) and As(V). oAs can be found in traces as monomethylarsenic acid, MMA(V), and dimethylarsenic acid, DMAs(V). Three types of resins: a strong base anion exchange (SBAE) and two hybrid (HY) resins: HY-Fe and HY-AgCl, based on the activity of hydrated iron oxides and a silver chloride were investigated. It was found that the sorption processes (ion exchange, adsorption and chemisorptions) of arsenic species on SBAE (ion exchange) and HY resins depend on pH values of water. The quantitative separation of molecular and ionic forms of iAs and oAs was achieved by SBAE and pH adjustment, the molecular form of As(III) that exists in the water at pH <8.0 was not bonded with SBAE, which was convenient for direct determination of As(III) concentration in the effluent. HY-Fe resin retained all arsenic species except DMAs(V), which makes possible direct measurements of this specie in the effluent. HY-AgCl resin retained all iAs which was convenient for direct determination of oAs species concentration in the effluent. The selective bonding of arsenic species on three types of resins makes possible the development of the procedure for measuring and calculation of all arsenic species in water. In order to determine capacity of resins the preliminary investigations were performed in batch system and fixed bed flow system. Resin capacities were calculated according to breakthrough points in a fixed bed flow system which is the first step in designing of solid phase extraction (SPE) module for arsenic speciation separation and determination. Arsenic adsorption behavior in the presence of impurities showed tolerance with the respect to potential interference of anionic compounds commonly found in natural water. Proposed method was established performing standard procedures: with external standard, certified reference material and standard addition method. Two analytical techniques: the inductively coupled plasma mass spectrometry (ICP-MS) and atomic absorption spectroscopy-hydride generation (AAS-GH) were comparatively applied for the determination of arsenic in all arsenic species in water. ICP-MS detection limit was 0.2 μg L⁻¹ and relative standard deviation (RSD) of all arsenic species investigated was between 3.5 and 5.1%.     

Arsenic speciation based on ion exchange high-performance liquid chromatography hyphenated with hydride generation atomic fluorescence and on-line UV photo oxidation

An on-line method capable of the separation of arsenic species was developed for the speciation of arsenite As(III), arsenate As(V), monomethylarsenic (MMA) and dimethylarsenic acid (DMA) in biological samples. The method is based on the combination of high-performance liquid chromatograph (HPLC) for separation, UV photo oxidation for sample digestion and hydride generation atomic fluorescence spectrometry (HGAFS) for sensitive detection. The best separation results were obtained with an anion-exchange AS11 column protected by an AG11 guard column, and gradient elution with NaH2PO4 and water as mobile phase. The on-line UV photo oxidation with 1.5% K2S2O8 in 0.2 mol L(-1) NaOH in an 8 m PTFE coil for 40 s ensures the digestion of organoarsenic compounds. Detection limits for the four species were in the range of 0.11-0.15 ng (20 microL injected). Procedures were validated by analysis of the certified reference materials GBW09103 freeze-dried human urine and the results were in good agreement with the certified values of total arsenic concentration. The method has been successfully applied to speciation studies of blood arsenic species with no need of sample pretreatment. Speciation of arsenic in blood samples collected from two patients after the ingestion of realgar-containing drug reveals slight increase of arsenite and DMA, resulting from the digestion of realgar.