Pt/K2La2Ti3O10催化剂的合成及其光催化分解甲醇水溶液制氢

用高温固相法合成了具有类钙钛矿型结构的层状化合物K₂La₂Ti₃O₁₀, 用XRD, UV-DRS对其进行表征. 利用不同还原方法制备了Pt/K₂La₂Ti₃O₁₀光催化剂, 并且用脉冲氢氧滴定法(HOT)测定了K₂La₂Ti₃O₁₀表面Pt的分散度. 考察了Pt/K₂La₂Ti₃O₁₀光催化分解甲醇水溶液制氢的活性. 比较了负载Pt与负载Ni和纯的K₂La₂Ti₃O₁₀的光催化活性. 研究了Pt负载量、不同还原方法对光催化分解水制氢反应活性的影响. 在最佳的Pt负载量2%(质量百分比)下, 产氢速率达到233.88 mmol·h^&;#8722;1. 讨论了该催化剂的能带结构及反应机理.     

Ce掺杂K2La2Ti3O10催化剂的可见光高效催化制氢的研究

采用高温固相法合成了铈掺杂的K₂La₂Ti₃O₁₀催化剂, 利用X射线衍射(XRD)、紫外-可见漫反射(UV-vis DRS)、透射电镜(TEM)和X射线光电子能谱(XPS)对催化剂进行了表征. 考察了催化剂的可见光催化分解甲醇水溶液制氢的活性, 并对可见光催化机理进行了分析. 研究表明, 铈的掺杂没有改变K₂La₂Ti₃O₁₀的微晶结构, 并使催化剂粒径有所减小. 紫外可见漫反射分析表明禁带宽度为2.3 eV左右, 对可见光具有较高吸收. XPS表明La和Ti为＋3和＋4价, 而Ce则是＋3和＋4的混合价态. 担载2 wt% Pt后, 在可见光下光催化活性大大提高, 当铈的掺杂量为0.5 mol%(即Ce取代La的摩尔百分量)时, 光催化活性达到最大, 产氢速率为0.05 mmol/h; 光照5 h后产氢量为0.22 mmol, 而纯K₂La₂Ti₃O₁₀的产氢量只有0.037 mmol.     

硬脂酸法制备超细K2La2Ti3O10及其酸交换性质研究

A new stearic acid method(SAM) has been used to prepare ultrafine K₂La₂Ti₃O₁₀ nanocrystalline. Each state of synthesis process was followed by the use of FT-IR analysis. The resulting materials have been characterized by means of XRD， TEM， BET surface area analysis. The acid-exchanging property of the obtained product was also studied. The experimental results showed that comparing with the product of traditional solid-state reaction， the particle size of the K₂La₂Ti₃O₁₀ synthesized by SAM is greatly reduced， BET surface area is high(more than 11.83m²·g^-1) and has different acid-exchanging properties. It can be easily exfoliated in 2mol·L^-1 HNO₃ so-lution.     

La3+掺杂CaFe2O4材料的制备及室温检测超低浓度甲醛

采用静电纺丝法成功制备了La³⁺掺杂CaFe₂O₄材料。通过X射线衍射、扫描电子显微镜和X射线光电子能谱对La³⁺掺杂CaFe₂O₄材料的结构和形貌进行了表征。随后，研究了La³⁺的掺杂量（质量分数）对CaFe₂O₄气敏性能的影响。研究表明，3% La³⁺掺杂CaFe₂O₄材料在室温下对100 μL·L^-1甲醛的响应最高（R_a/R_g=14.1）。更为重要的是，对甲醛的最低检测限低至0.1 nL·L^-1，并且响应/恢复时间仅为4.3 s/8.4 s。     

固体电解质La2-xCaxMo1.7W0.3O9-δ(0≤x≤0.2)的合成、表征及电性能

在氧离子导体La₂Mo_1.7W_0.3O₉的基础上，采用固相法合成了La位掺杂的Ca系列新型氧化物La_2-xCa_xMo_1.7W_0.3O_9-δ(0≤x≤0.2)。通过XRD、Raman和XPS等手段对化合物结构进行表征，交流阻抗谱测试其电性能。结果表明：掺杂离子Ca²⁺的半径小于基质离子La³⁺的半径导致晶格收缩；Ca的掺杂在La₂Mo_1.7W_0.3O₉自身内置氧空位的基础上增加了额外的氧空位，提高了氧离子导体的电导率，550 ℃电导率由0.79 × 10^-4 S·cm^-1 (x=0.0)增加到1.5 × 10^-4 S·cm^-1 (x=0.16，0.2)，电导率增加89.9%。     

Sb2O3/BiVO4/WO3异质结构建及光电催化合成过氧化氢

采用溶剂热法-旋涂法构建了Sb₂O₃/BiVO₄/WO₃半导体异质结,并采用X射线衍射、扫描电子显微镜、X射线光电子能谱等手段表征了其物化性质。在1.23 V(vs RHE)电位下,BiVO₄/WO₃的光电流密度相对于BiVO₄提高了2倍。进一步复合Sb₂O₃之后,虽然Sb₂O₃/BiVO₄/WO₃薄膜的光电流密度有所下降,但其光电催化产H₂O₂的法拉第效率和产生速率得到明显提升。在1.89V(vs RHE)电位下,3c-Sb₂O₃/BiVO₄/WO₃薄膜产 H₂O₂的法拉第效率提高到约 19%;1c-Sb₂O₃/BiVO₄/WO₃薄膜 H₂O₂产生速率从约2.1 μmol·h^-1·cm^-2提高到约3.6 μmol·h^-1·cm^-2。此外,Sb₂O₃的复合显著提高了BiVO₄/WO₃电极材料的光电催化稳定性。     

Cu/SO42-/La2O3-ZrO2-Al2O3催化剂的制备及其对C3H6选择还原NO的催化性能

以Al₂O₃为基质，添加ZrO₂和La₂O₃，制成La₂O₃-ZrO₂-Al₂O₃复合载体，然后采用SO₄^2-进行改性，再负载上Cu²⁺，制备了铜基SO₄^2-改性的复合载体催化剂(Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃)。考察了它在富氧条件下对丙烯选择还原NO的催化性能，并借助XRD、SEM、TG、Py-IR、NH₃-TPD、FTIR和TPR等方法研究了Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃的结构和性能的关系。结果表明，ZrO₂的加入主要有利于提高催化剂的低温活性；La₂O₃的加入则主要有利于提高催化剂的热稳定性和还原性能；SO₄^2-能够与Zr形成螯合双配位结构，大幅度促使催化剂表面酸量增加并且酸性增强；因此，有效地提高了Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃在富氧条件下对丙烯选择还原NO的催化活性和水热稳定性。在无水条件下，Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃能使NO的最大转化率高达84.3%，即使在275 ℃ 10%水蒸气存在的情况下，仍能使NO的转化率高达81.2%。     

TiO2/石墨烯复合材料的合成及光催化分解水产氢活性

利用石墨粉根据Hummers氧化法制得氧化石墨,并进一步还原得到石墨烯。采用溶胶-凝胶法以钛酸四丁酯和石墨烯为起始材料制备了二氧化钛(TiO₂)和石墨烯的复合光催化材料。研究了该复合材料在紫外-可见光以及可见光条件下的光催化分解水制氢活性。结果表明,紫外-可见光照射下,TiO₂/石墨烯复合光催化材料的光催化分解水产氢速率为8.6 μmol·h^-1,远大于同条件下商业P25的产氢速率 (4.5 μmol·h^-1),光解水产氢活性提高了近2倍;可见光下光照3 h,TiO₂/石墨烯复合材料的光催化分解水产氢量约为0.2 μmol。     

Cr2O3和CrO3/Cr2O3催化剂的2-氯-1,1,1-三氟乙烷气相氟化反应的活性物种和失活

采用沉淀法和浸渍法制备了2种铬基（Cr₂O₃和CrO₃/Cr₂O₃）催化剂,用于气相氟化2-氯-1,1,1-三氟乙烷合成1,1,1,2-四氟乙烷。研究发现含有低价铬（Cr³⁺）物种的Cr₂O₃催化剂上2-氯-1,1,1-三氟乙烷的稳态转化率为18.5%,而含有高价铬（Cr⁶⁺）物种和低价铬（Cr³⁺）物种的CrO₃/Cr₂O₃催化剂初始转化率达到30.6%,然而存在明显的失活。含有Cr⁶⁺物种的CrO₃/Cr₂O₃催化剂的2-氯-1,1,1-三氟乙烷氟化反应初始TOF值为1.71×10^-4 mol_HCFC-133a·mol_Cr（Ⅵ）^-1·s^-1,高于含有Cr³⁺物种的Cr₂O₃催化剂（4.16×10^-5 mol_HCFC-133a·mol_Cr（Ⅲ）^-1·s^-1）。Cr₂O₃催化剂在氟化反应前后催化剂的物相结构保持不变;而含有高价铬物种的CrO₃/Cr₂O₃催化剂经HF反应后生成了CrO_xF_y活性物种。然而,CrO_xF_y物种在反应中挥发或转化成稳定但无活性的CrF₃,从而导致催化剂失活。     

Cr2O3和CrO3/Cr2O3催化剂的2-氯-1，1，1-三氟乙烷气相氟化反应的活性物种和失活

采用沉淀法和浸渍法制备了2种铬基（Cr₂O₃和CrO₃/Cr₂O₃）催化剂,用于气相氟化2-氯-1,1,1-三氟乙烷合成1,1,1,2-四氟乙烷。研究发现含有低价铬（Cr³⁺）物种的Cr₂O₃催化剂上2-氯-1,1,1-三氟乙烷的稳态转化率为18.5%,而含有高价铬（Cr⁶⁺）物种和低价铬（Cr³⁺）物种的CrO₃/Cr₂O₃催化剂初始转化率达到30.6%,然而存在明显的失活。含有Cr⁶⁺物种的CrO₃/Cr₂O₃催化剂的2-氯-1,1,1-三氟乙烷氟化反应初始TOF值为1.71×10^-4 mol_HCFC-133a·mol_Cr(Ⅵ)^-1·s^-1,高于含有Cr³⁺物种的Cr₂O₃催化剂（4.16×10^-5 mol_HCFC-133a·mol_Cr(Ⅲ)^-1·s^-1）。Cr₂O₃催化剂在氟化反应前后催化剂的物相结构保持不变;而含有高价铬物种的CrO₃/Cr₂O₃催化剂经HF反应后生成了CrO_xF_y活性物种。然而,CrO_xF_y物种在反应中挥发或转化成稳定但无活性的CrF₃,从而导致催化剂失活。     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

The reaction of MgCl2·4H2O with CCl2F2

A new reaction of MgCl₂·4H₂O with CCl₂F₂ is investigated by DTA and TG from room temperature to 350 °C. It is observed that MgF₂ was obtained between 252 and 350 °C, Below the temperature, MgCl₂·4H₂O dehydrates and hydrolyzes to MgCl₂ and Mg(OH)Cl, which are the real reactants of the reaction with CCl₂F₂. The formation of MgF₂ is ascribed to the reaction of MgCl₂ and Mg(OH)Cl with HF, which forms by decomposition of CCl₂F₂ with the taking part in of H₂O released from dehydration of hydrated magnesium chloride on the surface of MgCl₂ and Mg(OH)Cl, which catalyzes the decomposition of CCl₂F₂ in this case. Consequently, the reactions are tested in the fluid-bed condition. It is found that MgF₂ formed at temperatures down to 200 °C in a fluid-bed reactor. This reaction may be used as a method of disposing of the environmentally sensitive CCl₂F₂ (rather than release into the atmosphere). It is also a method for the preparation of MgF₂.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

(Cl2AlNH2)n和(H2AlNH2)n(n=1～5)簇结构及其热力学性质

用HF自洽场理论和密度泛函理论(DFT)的B3LYP方法,在6 31G水平上研究了低聚物(Cl2AlNH2)n和(H2AlNH2)n(n=1～5)簇的几何构型、电子结构和聚合反应热力学性质,比较了两个系列化合物中化学键的强度.结果表明,Cl2AlNH2和H2AlNH2分子为C2 (EC)平面型结构,其中Al－N为由一个σ键和一个键组成的双键.(Cl2AlNH2)n和(H2AlNH2)n(n=1～5)分子为Dnh对称,Al－N是典型的σ单键 .低聚物(Cl2AlNH2)n和(H2AlNH2)n的稳定性顺序分别为: 3 > 2 > 4> 5 > 1和8 > 7 > 9 > 11 > 6.     

The crystal structure determinations and refinements of K2S2O7, KNaS2O7 and Na2S2O7 from X-ray powder and single crystal diffraction data

The crystal structures of K₂S₂O₇, KNaS₂O₇ and Na₂S₂O₇ have been solved and/or refined from X-ray synchrotron powder diffraction data and conventional single-crystal data. K₂S₂O₇: From powder diffraction data, monoclinic C2/c, Z=4, a=12.3653(2), b=7.3122(1), , β=93.0792(7)°, R_Bragg=0.096. KNaS₂O₇: From powder diffraction data; triclinic , Z=2, a=5.90476(9), b=7.2008(1), , α=101.7074(9), β=90.6960(7), γ=94.2403(9)°, R_Bragg=0.075. Na₂S₂O₇: From single-crystal data; triclinic , Z=2, a=6.7702(9), b=6.7975(10), , α=116.779(2), β=96.089(3), γ=84.000(3)°, R_F=0.033. The disulphate anions are essentially eclipsed. All three structures can be described as dichromate-like, where the alkali cations coordinate oxygens of the isolated disulphate groups in three-dimensional networks. The K-O and Na-O coordinations were determined from electron density topology and coordination geometry. The three structures have a cation-disulphate chain in common. In K₂S₂O₇ and Na₂S₂O₇ the neighbouring chains are antiparallel, while in KNaS₂O₇ the chains are parallel. The differences between the K₂S₂O₇ and Na₂S₂O₇ structures, with double-, respectively single-sided chain connections and straight, respectively, corrugated structural layers can be understood in terms of the differences in size and coordinating ability of the cations.     

EuZn2Si2 and EuZn2Ge2 Grown from Zn or Ga(ln)/Zn Flux

Single crystals of the novel ternary compounds EuZn₂Si₂ and EuZn₂Ge₂ were grown from pure gallium, indium, or zinc metal used as a flux solvent. Crystal properties were characterized using X-ray single-crystal analyses via Gandolfi and Weissenberg film techniques and by four-circle X-ray single-crystal diffractometry. The new compounds crystallize with ternary derivative structures of BaAl₄, i.e., EuZn₂Si₂ with ThCr₂Si₂-type (a=0.42607(2) nm, c=1.03956(5) nm, I4/mmm, R₁=0.038) and EuZn₂Ge₂ with CaBe₂Ge₂-type (a=0.43095(2) nm, c=1.07926(6) nm, P4/nmm, R₁=0.067). XAS and magnetic measurements on EuZn₂Si₂ and EuZn₂Ge₂ revealed in both compounds the presence of Eu²⁺ ions carrying large magnetic moments, which order magnetically at low temperatures. The magnetic phase transition occurs at T_N=16 and 7.5 K for the silicide and the germanide, respectively. In EuZn₂Si₂ there occurs a spin reorientation at 13 K and furthermore some canting of antiferromagnetically ordered moments below about 10 K. In EuZn₂Ge₂ a canted antiferromagnetic structure is formed just at T_N.     

Energetics of copper diphosphates – Cu2P2O7 and Cu3(P2O6OH)2

Differential scanning calorimetry and high temperature oxide melt solution calorimetry are used to study enthalpy of phase transition and enthalpies of formation of Cu₂P₂O₇ and Cu₃(P₂O₆OH)₂. α-Cu₂P₂O₇ is reversibly transformed to β-Cu₂P₂O₇ at 338–363 K with an enthalpy of phase transition of 0.15 ± 0.03 kJ mol⁻¹. Enthalpies of formation from oxides of α-Cu₂P₂O₇ and Cu₃(P₂O₆OH)₂ are −279.0 ± 1.4 kJ mol⁻¹ and −538.8 ± 2.7 kJ mol⁻¹, and their standard enthalpies of formation (enthalpy of formation from elements) are −2096.1 ± 4.3 kJ mol⁻¹ and −4302.7 ± 6.7 kJ mol⁻¹, respectively. The presence of hydrogen in diphosphate groups changes the geometry of Cu(II) and decreases acid–base interaction between oxide components in Cu₃(P₂O₆OH)₂, thus decreasing its thermodynamic stability.     

XRD and Si MAS-NMR spectroscopy across the β-Lu2Si2O7-β-Y2Si2O7 solid solution

Samples in the system Lu_2−xY_xSi₂O₇ (0?x?2) have been synthesized following the sol-gel method and calcined to 1300 °C, a temperature at which the β-polymorph is known to be the stable phase for the end-members Lu₂Si₂O₇ and Y₂Si₂O₇. The XRD patterns of all the compositions studied are compatible with the structure of the β-polymorph. Unit cell parameters are calculated as a function of composition from XRD patterns. They show a linear change with increasing Y content, which indicates a solid solubility of β-Y₂Si₂O₇ in β-Lu₂Si₂O₇ at 1300 °C. ²⁹Si MAS NMR spectra of the different members of the system agree with the XRD results, showing a linear decrease of the ²⁹Si chemical shift with increasing Y content. Finally, a correlation reported in the literature to predict ²⁹Si chemical shifts in silicates is applied here to obtain the theoretical variation in ²⁹Si chemical shift values in the system Lu₂Si₂O₇-Y₂Si₂O₇ and the results compare favorably with the values obtained experimentally.     

CeO2改性Ag-V2O5/TiO2催化剂的甲基吡啶氧化脱甲基性能

以锐钛矿TiO_2为载体,考察了CeO_2改性对Ag-CeO_2-V_2O_5/TiO_2催化3-甲基吡啶氧化脱甲基性能的影响,并优化了催化剂组成与制备条件.结果表明:Ce掺杂改性不仅能够与V物种作用形成Ce VO_4,而且促进V_2O_5分散,改善活性组分的氧化还原性能,从而提高3-甲基吡啶脱甲基转化率与选择性,改善Ag-V_2O_5/TiO_2催化性能.适宜的催化剂组成为V_2O_5负载量15%,Ce/V的摩尔比0.33,Ag质量分数1.0%.过高的焙烧温度将导致TiO_2载体向金红石型转变,Ag-CeO_2-V_2O_5/TiO_2适宜制备条件为450℃焙烧4 h.