Y_2O_3∶Eu~(3+)纳米线阵列的制备与表征

Y2 O3∶ Eu3+红色荧光粉由于色纯度高、化学性质稳定和量子效率接近 1 0 0 %而广泛用于荧光灯和投影电视等方面 .近年来 ,Y2 O3∶Eu3+的大量研究工作主要集中于纳米粉末的制备方法及其与体相材料不同的发光特性 [1～ 3] .最近 ,有关 Y2 O3∶ Eu3+及其稀土化合物的纳米管、纳米线和纳米带一维材料的制备成为研究热点 . Wu Changfeng等[4 ,5] 利用表面活性剂合成了 Y2 O3∶ Eu3+纳米管 .激光格位选择激发测试结果表明 ,Eu3+在纳米管中占据 3个不同的格位 ,其 61 1 nm处的红色发光峰出现了宽化 .HeYu等 [6 ] 采用水热法及退火处理制备出…     

空气中合成M2B4O7:Eu3+(M=Na,K)荧光体及其性质表征

以M2B4O7(M=Na,K)为基质,在空气中掺杂稀土元素Eu3+得到了Na2B4O7:Eu3+和K2B4O7:Eu3+荧光体.探讨了体系的烧结条件和荧光性质,分析了晶体的结构.结果表明,虽然两种体系的最佳合成条件不同,但是体系中都同时存在[BO4]和[BO3]结构;稀土离子Eu3+的发光以电偶极跃迁5D0-7F2为主,处于非中心对称的格位上,并且可以很好地存在于基质中,Na2B4O7:Eu3+具有较强的发光强度.     

溶剂热合成纳米球状La2O2S:Eu3+荧光粉

Eu3+离子激活的硫氧化物荧光粉是目前国内外广泛使用的CRT红色发光材料[1]. 它具有色纯度高、色彩不失真、亮度-电流饱和度特性好和稳定性高等特性, 已成为CRT不可替代的红色荧光粉. 此外, 掺杂或不掺杂Eu3+的硫氧化镧是还原SO2有害气体为S单质的优良催化剂[2,3]. 近年来兴起的纳米材料是有可能在本世纪得到广泛应用的材料; 掺杂稀土离子的硫氧化物有望应用于各种显示技术及催化剂中. 最近, 吴长峰等[4]在Y2O3∶Eu3+纳米管中观察到发射峰展宽等特性. 因而, 研究Eu3+离子激活的硫氧化镧纳米荧光粉是很有意义的.     

YBO3:Eu荧光粉的水热法制备及形貌控制

用水热法在低于300℃成功地制备出具有不同形貌的YBO3:Eu3+荧光粉,其反应温度比固相反应了约800℃.研究了初始原料、pH值、反应温度、反应溶剂和催化剂等条件对目的产物形貌及粒度的,得到了具有Vaterite结构、粒度分布均匀的球形荧光粉的最佳合成工艺.在254nm激发下,水热法的球形Y0.95Eu0.05BO3荧光粉最强发射峰位于598nm处,属于Eu3+的5D0→7F1的跃迁,是固相反应所品的1.5倍.这些结果表明,在PDP和荧光灯等显示和照明用荧光粉的制备中水热法具有潜在的应用.     

蓝色长余辉材料CaAl2O4:Eu2+,Nd3+的合成及其发光性能

采用高温固相法合成了系列单相Ca(1-x-y)Al2O4:Eu2+x,Nd3+y(0≤x≤0.045,0≤y≤0.0037)粉末样品,并表征了其发光特性.研究结果表明,样品的发射光谱为最大发射峰位于440nm的宽带谱,属于Eu2+的4f65d→4f7跃迁.通过对Eu2+,Nd3+掺杂量与样品发光性能之间关系的研究发现,Eu2+和Nd3+最佳掺杂量分别为x=0.00125和y=0.0025,并且Nd3+对改善蓝色长余辉材料CaAl4:Eu2+的余辉性能具有重要的作用.在最佳掺杂条件下,样品的余辉时间可达1000min,初始亮度大于1200mcd/m2,60min后发光粉的亮度仍然在10mcd/m2以上.利用正电子湮灭技术和热释光技术,研究了Eu2+和Nd3+对CaAl2O4:Eu2+,Nd3+材料的发光性能的影响.     

Al2O3/蒙脱土:Eu2+架状结构发光材料的制备及发光性能研究

采用高温固相法,在还原气氛下制备出Al2O3/蒙脱土:Eu2+光致发光材料。研究了原料配比、烧结温度、保温时间以及激活剂Eu2+的含量对发光性能的影响。实验结果表明:加入蒙脱土后,所制备的样品仍保持Al2O3的架状结构,晶格常数发生变化,晶体产生畸变,使得Eu2+更容易进入到晶格中。荧光光谱分析显示,发射光谱是两个宽峰组成,对应于Eu2+的4f65d→4f7(8S7/2)宽带允许跃迁。发光机制分析认为,宽峰结构由Eu0.92[Al1.76Si2.24O8]新相产生,生成的新相增加了Eu2+的取代格位,形成新的发光中心。因此Eu2+不仅取代了Al2O3八面体中Al的格位,而且取代了蒙脱土层间所吸附的阳离子格位,使样品发光强度提高了220%。     

WO3/YF3:Eu3+复合纳米材料的制备与发光性能

采用直接沉淀法制备了WO_3/YF_3∶Eu~(3+)复合纳米材料,并对其结构、组成、形貌和发光性能进行了研究。XRD分析表明:复合纳米材料由纳米粒子WO3和结晶良好的正交晶系的YF3∶Eu~(3+)组成。SEM照片表明:片状WO3颗粒表面沉积了分散性较好、粒径均匀(尺寸为10~50 nm)的YF3∶Eu3纳米颗粒。荧光光谱分析表明:该复合纳米材料具有良好的发光性,以593 nm附近的5D0→7F1磁偶极跃迁为最强发射峰,与纯的YF3∶Eu~(3+)相比WO_3/YF_3∶Eu~(3+)发光强度明显增强,表明具有表面等离子共振效应的WO3纳米粒子对壳层的YF3∶Eu~(3+)起到发光增强作用。     

纳米晶Y_2O_3∶Eu~(3+)的合成及其热分析动力学

以Y(NO3)3、Eu2O3、CO(NH2)2为原料,使用超声波作用下的均匀沉淀法合成了纳米晶荧光粉Y2O3∶Eu3+。利用不同升温速率的热重及差热分析研究了纳米晶Y2O3∶Eu3+的合成动力学及晶粒生长动力学。研究表明,纳米晶Y2O3∶Eu3+的前驱体分解过程可分为3个步骤,利用Doyle-Ozawa法和Kissinger法分别计算了各个反应阶段的表观活化能,用Kissinger法确定每个反应阶段的反应级数和频率因子,并给出了各个阶段的动力学方程。根据晶粒生长动力学理论计算纳米荧光粉Y2O3∶Eu3+晶粒生长活化能为17.80kJ·mol-1,表明热处理过程中纳米晶粒的长大为扩散生长机制。     

Yb3+/Tm3+共掺杂的钨酸镉纳米晶发光性能的研究

本文采用水热法制备了稀土离子Yb³⁺/Tm³⁺共掺杂的钨酸镉纳米晶。运用X-射线粉末衍射、场发射环境扫描电子显微镜和光谱分析对制备的样品的结构和发光性能进行了表征。根据XRD图谱可知, 钨酸镉为单斜晶系, 晶粒平均尺寸在28 nm左右。从ESEM图片可明显看出, 钨酸镉呈纳米棒结构, 直径在30 nm左右, 长径比在5~8之间。利用980 nm半导体激光器激发钨酸镉纳米晶得到样品的发射光谱, 存在一个较强的蓝光发射, 发光峰位于481 nm,对应于Tm³⁺的¹G₄→³H₆能级的跃迁, 分析了Tm³⁺/Yb³⁺离子共掺体系的发光机制。讨论了发光强度随稀土离子浓度的变化, 当Tm³⁺离子的掺杂浓度在2%, Yb³⁺/Tm³⁺物质的量浓度比为10:1时钨酸镉纳米晶的发光强度最强。根据泵浦功率与发光强度之间的关系, 可知处于481 nm的蓝光发射属于三光子过程, 由发光强度与掺杂浓度之间的双对数衰减曲线可知, 引起蓝光发射源于Tm³⁺的电偶极跃迁。     

纳米MgBO_2(OH):Eu~(3+)的制备及发光性能研究

利用水热法,制备得到了纳米线组装的绒球状和纳米带聚集的絮状Mg BO2(OH):Eu3+,对它们进行了EDS、XRD、IR、SEM等表征及发光性能研究。研究发现两个产品的最高激发峰和发射峰分别都位于λ=250nm和λ=615nm处,为红色发光材料;且发现绒球状Mg BO2(OH):Eu3+的峰强度明显强于絮状Mg BO2(OH):Eu3+,但絮状Mg BO2(OH):Eu3+的红橙比(R/O)更高。     

Ce3+,Tb3+,Eu3+共掺杂Sr2MgSi2O7体系的白色发光和能量传递机理

通过正交试验,采用高温固相法制备了Sr2-x-y-zMgSi2O7∶xCe3+,yTb3+,zEu3+系列样品.使用X射线衍射仪和荧光光谱仪表征了样品的物相和发光性质,并讨论了Ce3+-Tb3+-Eu3+共掺杂Sr2MgSi2O7体系中的能量传递过程.实验结果表明,在327 nm波长激发下,所合成荧光粉的发射峰主要位于387 nm(蓝紫)、542nm(绿)和611 nm(红)处;分别以387,542和611 nm为监控波长,所得激发光谱显示荧光粉在327 nm处有最好的激发.在327 nm光激发下,系列样品发光进入白光区.最优化的荧光粉为Sr1.91MgSi2O7∶0.01Ce3+,0.05Tb3+,0.03Eu3+,其色坐标为(0.337,0.313),是一种潜在的发光二极管(LED)用白色荧光粉.     

白色荧光粉NaGd（MoO4）2:Dy3+,Eu3+的水热合成及发光性能

采用谷氨酸辅助水热法合成了八面体形NaGd(MoO4)2:Dy3+,Eu3+白色荧光粉.X射线衍射结果表明,合成的样品为四方晶系的NaGd(MoO4)2纯相.扫描电子显微镜照片显示所制备的粒子为八面体形,各边长约为2μm.荧光光谱结果表明,在NaGd(MoO4)2:4%Dy3+,yEu3+(y=0,0.5%,0.6%,0.7%,0.8%,0.9%,1.0%)样品中,随着Eu3+掺入量的增加,Dy3+的发射峰逐渐减弱,而Eu3+的发射峰逐渐增强,说明Dy3+-Eu3+之间存在能量传递.通过色坐标图可知,当Eu3+掺杂量y=0.9%时,荧光粉的色坐标(0.338,0.281)与标准的白光色坐标(0.33,0.33)接近,表明NaGd(MoO4)2:4%Dy3+,0.9%Eu3+是很好的近紫外光激发下的白色荧光粉.     

Effects of precipitant on microstructure and luminescent properties of Lu2O3:Eu3+ nanopowders and ceramics

Nanocrystalline Lu(2)O(3):Eu(3+) was prepared by co-precipitation method using ammonium hydrogen carbonate and ammonium oxalic acid as precipitants, respectively. The crystal structure and morphology were analyzed by means of XRD and TEM. The resultant powders were sintered into transparent ceramics in vacuum and then in nitrogen without any additive. The surface morphology of the unpolished sintered specimens was characterized using SEM. The effect of different precipitants on microstructure of the nanopowders and transparency of the ceramics are compared. The excitation and emission spectra of Lu(2)O(3):Eu(3+) powders and ceramics were measured at room temperature by using synchrotron radiation as the light source. The fluorescence decay times of all specimens were analyzed. Luminescence of the ceramics decays faster than the corresponding nanopowders.     

花瓣形YBO3∶Eu3+发光薄膜的制备与表征

本文报道了通过水热合成在AAO模板上组装出花瓣形YBO3∶Eu3+薄膜的研究工作.     

Synthesis and Photoluminescence Properties of Uniform Y2O3:Eu3+ Hollow Spheres with Tunable Shell Thickness

Y2O3:Eu3+ hollow spheres were successfully prepared with melamine formaldehyde(MF) spheres as template. The MF spheres played a significant role in directing the formation of the hollow shells which are composed of numerous primary nanoparticles. Furthermore, the shell thickness of these hollow spheres could be readily tailored by adjusting the dosage of MF template. Based on the photoluminescence(PL) investigation, the red emission intensities(613 nm) of these Y2O3:Eu3+ hollow spheres are greatly influenced by their shell thickness and it was found that hollow spheres with thin shell thickness and intact hollow structures permit a better PL performance.     

NaGdF4:Eu3+/AAO薄膜的制备与表征

采用水热法在多孔阳极氧化铝(AAO)模板上制备了NaGdF<,4>:Eu<'3+>(摩尔分数5.0%)/AAO薄膜,并研究了制备方法、溶液浓度和退火温度对薄膜样品形貌、结构和发光性质的影响.XRD结果表明,在低于500 ℃退火,得到具有NaGdF<,4>六方相结构的NaGdF<,4>:Eu<'3+>/AAO薄膜;而在5...     

Template induced sol-gel synthesis of highly ordered LaNiO3 nanowires

The highly ordered LaNiO₃ nanowires of the rare-earth perovskite-type composite oxide were controlled synthesized within a porous anodic aluminum oxide (AAO) template by means of sol-gel method using nitrate as raw materials and citric acid as chelating agent. The results of scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that the obtained LaNiO₃ nanowires had a uniform length and diameter, which were determined by the thickness and the pore diameter of the applied AAO template. The results of X-ray diffraction (XRD) and the selected-area electron diffraction (SAED) indicated that the LaNiO₃ nanowires were perovskite-type crystalline structures. Furthermore, X-ray photoelectron spectroscopy (XPS) and the energy dispersive X-ray (EDX) spectroscopy demonstrated that the stoichiometric LaNiO₃ was formed.     

水热法制备具有光滑表面的球形Y2O3∶Eu3+发光材料

The spherical Y₂O₃∶Eu³⁺ luminescent particles with size of 0.5～3 μm and smooth surface were synthesized by hydrothermal method. The resulted Y₂O₃∶Eu³⁺ precursors and the calcined particles were characterized by differential thermal analysis (DTA) and thermogravimetric (TG) analysis, X-ray diffraction (XRD), Fourier-transform IR spectroscopy (FTIR), scanning electron microscopy (SEM) and photoluminescence spectra (PL). FTIR, TG-DTA, XRD measurements show that the precursors are crystal with hydroxyl and carbonate group, and the pure cubic yttria is obtained after annealing above 700 ℃. The SEM images indicate that the Y₂O₃∶Eu³⁺ particles are in spherical shape and with smooth surface. PL analysis shows that the particles present characteristic red emission of Eu³⁺.