稀土在电沉积锌—镍合金中的作用

锌—镍合金镀层具有耐蚀性高、低氢脆性和与基体的结合力好等特性 ,是良好的防护性镀层。当合金镀层的镍含量在 7～ 1 8% (质量 )时 ,镀层的耐蚀性最高 ,因此它可代替传统的锌镀层、锡镀层和镉镀层而广泛应用于电镀汽车钢板、航空航天及家电等行业[1～ 3] 。稀土元素 ( RE)包括了 1 5个镧系元素和钇元素 ,共 1 6个元素。由于稀土元素具有独特的电子层结构和化学性能 ,使稀土及其化合物在材料科学领域中的应用越来越广泛 ,尤其是稀土在电沉积过程中的研究及应用正日趋深入。文献资料表明 ,在电镀溶液中加入少量的稀土化合物后 ,可以改善镀液…     

火焰原子吸收光谱法测定钴镍合金镀层中钴

为了研究电流密度对电镀钴镍合金中钴含量的影响，利用原子吸收光谱法研究了在氨基磺酸钴一镍镀液中，赫尔槽试片上不同电流密度区合金镀层中钴的含量。结果表明，随着阴极电流密度的增加，合金镀层中钴的含量不断降低。同时原子吸收光谱法测定钴一镍电沉积合金镀层中钴含量的回收率为96．0％～104．0％，相对标准偏差为0．289／6～1．61％。该方法简便、快捷，结果准确度好，精密度高。原子吸收光谱法与赫尔槽方法的联合使用，能方便地研究合金电沉积过程中阴极电流密度对合金组成的影响。     

稀土添加剂对镀铬质量的影响

针对普通电镀镀层光亮性和结合强度差, 分散性和沉积速度低的实际, 应用远近阴极的研究方法, 系统地研究了稀土添加剂在常温和中温镀铬时对镀层光亮性、镀液分散性、离子的沉积速度和电流效率的影响, 实验结果表明稀土添加剂在中温镀铬时, 对镀层的光亮性、镀液的分散性、离子沉积速度和电流效率均有增强作用, 常温时对电流效率和离子沉积速度有较大的增强作用. 对电镀铬综合性能提高较大的稀土为Pr6O11, CeO2.     

甲基磺酸亚锡溶液中不同稳定剂的作用机制及电化学性质

研究了对苯二酚、邻苯二酚、间苯二酚和抗坏血酸4种稳定剂对甲基磺酸亚锡电镀液稳定性、电极极化及镀层表面形貌的影响.采用循环伏安法探究了镀液稳定性与稳定剂电化学性质的关系,通过交流阻抗和计时电位考察了稳定剂对镀液阴极极化性能的影响,分析了对苯二酚在电镀过程中的循环使用原理及对苯二酚的最佳使用浓度.结果表明,镀液的稳定性与稳定剂自身的还原能力及电化学活性之间存在重要联系,4种稳定剂对镀液稳定作用的大小顺序为对苯二酚邻苯二酚抗坏血酸间苯二酚,稳定效果最好的对苯二酚可以将镀液的储存时间延长一倍;苯二酚类稳定剂可以提高锡沉积的阴极极化程度,使晶粒细化,而抗坏血酸对锡沉积起到去极化作用;对苯二酚在电镀锡过程中兼具抗氧化剂、光亮剂和整平剂的作用,镀层的耐蚀性能测试结果表明,对苯二酚的最佳浓度为1.0 g/L.     

Cu含量对Ni-Cu-P化学镀层组织结构和性能影响

利用化学镀法制备出Ni-Cu-P合金镀层,研究了镀液中CuSO4·5H2O含量对合金镀层沉积速率和成分的影响. 通过XRD和SEM表征了不同CuSO4·5H2O质量浓度下Ni-Cu-P合金镀层的组织结构和表面形貌,运用极化曲线评价了合金镀层在质量分数为3.5%NaCl溶液中的耐蚀性能. 结果表明,随着镀液中CuSO4·5H2O质量浓度的增加,镀层沉积速率和P含量不断下降,Ni-P镀层中P的质量分数为14.98%. 当镀液中CuSO4·5H2O质量浓度为1.0 g/L时,P的质量分数为4.21%;镀层中Cu的含量随着镀液中CuSO4·5H2O含量的增加而增加. 当添加量为1.0 g/L时,镀层中Cu的质量分数达19.04%;镀层的结晶度随着Cu含量的上升不断增大,Cu的加入使镀层的表面形貌更加光滑;镀层的耐蚀性能随着镀液中CuSO4·5H2O含量的增加先上升后下降,当镀液中CuSO4·5H2O质量浓度为0.4 g/L时,Ni-Cu-P镀层表现出最优的耐蚀性能.     

主盐浓度和工艺条件对Sn-Ag-Cu合金镀层组成和形貌的影响

在弱酸性镀液中电沉积得到无铅Sn-Ag-Cu可焊性合金镀层。采用X射线荧光光谱仪(XRF)和扫描电子显微镜(SEM)研究了镀液中主盐浓度和电镀工艺条件对镀层的组成和形貌的影响。研究表明,Sn-Ag-Cu合金的电沉积是正则共沉积。镀液中Sn²⁺和Ag⁺浓度改变对镀层晶粒大小影响较大,Cu²⁺浓度的改变对镀层的平整度影响较大。电流密度增加、pH值下降、温度降低,都能使镀层结晶细致。     

稀土对电沉积Ni-P合金镀层耐蚀性的影响

研究了稀土对电沉积Ｎｉ－Ｐ合金度层耐蚀性及组织的影响,通过浸泡实验和极化曲线的测定。得出在镀液中添加一定量的稀土元素能显著改善镀层的耐蚀性能。ＸＲＤ,ＴＥＭ,ＥＤＳ结果表明,稀土元素具有促进Ｎｉ－Ｐ合金形成非晶组织的作用,由于稀土的加入,在远低于８％的Ｐ含量下,获得了以非晶态为主的组织。     

电化学方法制备铜钴纳米多层膜

采用旋转圆盘电极、双脉冲电位法从单一的含有铜离子和钴离子的镀液中电沉积Ｃｕ－Ｃｏ纳米多层膜、并用ＴＥＭ．ＡＥＳ和Ｘ－射线衍射研究镀层的形貌和组成。结果表明：多层膜结构为纯铜和含有少量铜的铜钴合金层交替组成,铜在钴层中的含量,随镀液中的铜含量的增大和转速的提高而提高。     

化学沉积镍-铁-磷合金和它的伏安行为(英文)

在以次亚磷酸钠为还原剂 ,硼酸为缓冲剂和柠檬酸钠为络合剂的碱性介质中 ,研究了镍_铁_磷合金化学沉积条件 (pH值 ,温度及 [Fe2 + ]/([Ni2 + ]+[Fe2 + ])物质的量比 )对沉积速率和镀层组成的影响 ;并由此建立镀液稳定的最佳沉积工艺 .实验表明 ,镀液中硫酸亚铁对沉积镍_铁_磷合金有阻碍作用 (降低了化学沉积速率 ) ,造成镀层中铁含量不高 (小于 2 0 % ) ,使用循环伏安技术研究了镍_铁_磷合金的电沉积机理 .结果发现铁对次亚磷酸钠的氧化不起催化作用 ,提高镀液温度和pH值有增加沉积速率之效     

非晶态Ni-Ce-P合金的共沉积与耐蚀性能

采用恒电位沉积、循环状安等方法研究了在水溶液中电沉积稀土合金的可能性 ,首次在含有CeCl3的弱酸性NaH2 PO2 镀液中获得了不同铈含量的Ni Ce P合金镀层 ,XPS、AES、XRD和SEM等实验技术表征了镀层的组成和结构 ,极化电阻和腐蚀电位的测试数据表明此镀层与Ni P无定形合金相比 ,具有更强的耐腐蚀能力 ,同时 ,讨论了沉积条件与镀层耐蚀性能的关系 ,结论是 :镀层中铈含量越高 ,其耐腐蚀性能越好 ,此外还对Ni Ce P的共沉积机理进行了初步探讨 ,指出在所研究的电沉积条件下 ,Ni Ce P合金共沉积可以用“诱导共沉积理论”合理解释     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。     

Stages of thermal decomposition of sodium oxo-salts of sulphur

Thermal behaviour of sodium oxo-salts of sulphur: Na₂SO₄, Na₂S₂O₇, Na₂S₂O₆, Na₂SO₃, Na₂S₂O₅, Na₂S₂O₄, Na₂S₂O₃, Na₂S₃O₆ and of sulphides Na₂S and Na₂S₂ was studied on heating up to 1000°C. The experiments were performed with anhydrous compounds obtained from commercial products by recrystallisation and dehydration. The stage mechanisms of decomposition of anionic sub-lattices of the salts have been proposed basing on the Górski’s morphological classification of simple species. The thermal stability and the stage decomposition mechanisms were correlated with the structure and the potential chemical properties of the salt anions. The thermal decomposition processes were studied by means of thermal analysis, and the decomposition products were identified by means of X-ray phase analysis.