Pt/Ce0.6Zr0.4O2催化剂在水煤气变换反应中的电导研究

采用浸渍法制备了不同载体(Ce0.6Zr0.4O2,CeO2和ZrO2)负载的Pt基水煤气变换反应(WGSR)催化剂, 并对其进行了活性评价. 利用X射线衍射(XRD), 程序升温还原(TPR)和原位电导等技术对样品进行了表征. 结果表明, Ce0.6Zr0.4O2固溶体具有比CeO2更高的氧转移能力, 因此促进了Pt/Ce0.6Zr0.4O2催化剂的WGSR活性.     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n(Ce)/n(Zr)比为0.67/0.33, 用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体. 采用这些固溶体作载体, 以Fe2O3为活性组分, 用浸渍法制备了一系列催化剂. BET结果显示, 将适量Ce0.67Zr0.33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积. TPR结果显示, 载体中引入适量的Ce0.67Zr0.33O2可以改善催化剂的氧化还原性能. XRD结果表明, Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况, 老化前后催化剂的晶相结构基本无明显变化. 特别是当载体中m(Ce0.67Zr0.33O2)∶m(Al2O3)的值为1∶2时, Fe2O3/CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能.     

Cu网负载CeO2-TiO2微纳米复合材料（CeO2-TiO2）/Cu的水热制备与性能

以Cu网为载体,Ti(OBu)4和Ce(NO3)3·6H2O为原料,Na3PO4·12H2O为矿化剂,采用一步水热法制备了多种不同形貌的Cu网负载CeO2-TiO2微纳米复合材料(CeO2-TiO2)/Cu.采用扫描电子显微镜(SEM)、X射线衍射仪(XRD)和紫外-可见漫反射分光光度计(UV-Vis DRS)对材料的形貌、结构及光吸收特性进行了表征,通过测试接触角表征了材料的浸润性.以20μmol/L亚甲基蓝(MB)溶液为目标降解物,测试了材料在可见光照射下的催化性能.结果表明,制备的TiO2为锐钛矿型,CeO2为方铈矿型;CeO2晶体比TiO2晶体更易负载于Cu网;改变制备过程中Ce(NO3)3·6H2O的用量、Na3PO4·12H2O浓度、水热反应时间及温度可实现(CeO2-TiO2)/Cu的形貌调控;(CeO2-TiO2)/Cu显示出超亲水性及可见光催化活性.     

Ce0.67Zr0.33O2对CH4燃烧催化剂Fe2O3/Al2O3的改性作用

固定n(Ce)/n(Zr)比为0.67/0.33,用共沉淀法制得一系列CeO2-ZrO2-Al2O3固溶体.采用这些固溶体作载体,以Fe2O3为活性组分,用浸渍法制备了一系列催化剂.BET结果显示,将适量Ce0.67Zr0.33O2引入到Al2O3载体中有助于催化剂保持较高的比表面积.TPR结果显示,载体中引入适量的Ce0.67Zr0.33O2可以改善催化剂的氧化还原性能.XRD结果表明,Fe2O3在CeO2-ZrO2-Al2O3载体上呈现出良好的分散状况,老化前后催化剂的晶相结构基本无明显变化.特别是当载体中m(Ce0.67Zr0.33O2)∶m(Al2O3)的值为1∶2时,Fe2O3/CeO2-ZrO2-Al2O3催化剂在甲烷催化燃烧中显示出最佳的催化性能和抗高温老化性能.     

Pt/CeO2/SBA-15催化剂上Pt-CeO2接触界面的相互作用

通过沉积沉淀法(Deposition precipitation, DP)将CeO2纳米粒子高度分散在SBA-15分子筛上, 进一步采用浸渍法负载Pt后制备了 Pt/CeO2/SBA-DP催化剂. 紫外-可见漫反射光谱分析表明, 在Pt/CeO2/SBA-DP催化剂上可以形成更多的Pt-CeO2接触界面, 有利于从CeO2到Pt的电子转移过程. CO程序升温还原(CO-TPR)测试证实, Pt/CeO2/SBA-DP催化剂上CeO2表面氧物种具有较高的还原能力.     

La2O3对CuO/CeO2水煤气变换反应催化剂微观结构及催化性能的影响（英文）

以La2O3为助剂,采用共沉淀法制备了具有良好催化活性和热稳定性的CuO/CeO2-La2O3水煤气变换反应催化剂,其中,当La2O3含量为2wt%时,催化剂的催化性能最为优异.同时运用X射线衍射、N2吸附-脱附、Raman光谱、程序升温还原等手段,研究了不同含量的La2O3对CuO/CeO2催化剂微观结构及催化性能的影响.结果表明,La2O3助剂进入了载体CeO2的晶格并对CuO/CeO2催化剂的微观结构和催化性能产生了直接影响,适量La2O3的添加可以抑制CuO和CeO2晶格的长大、增强CuO与CeO2间的相互作用、提高催化剂的比表面积、促进CeO2载体中生成更多的氧空位,CuO/CeO2催化剂的催化活性和热稳定性也明显改善.     

负载型钙钛矿催化氧化NO及抗SO_2性能研究

采用柠檬酸络合浸渍法制备了负载型钙钛矿氧化物La1-xCexCoO3/CeO2(x=0~0.3)催化剂,考察了不同Ce掺杂量对其催化氧化NO和抗硫性能的影响,并运用X射线衍射(XRD)、傅里叶红外光谱(FT-IR)、氮气物理吸附、程序升温还原(H2-TPR)、氧气程序升温脱附(O2-TPD)等手段对催化剂进行了表征。结果表明,催化剂的活性与其比表面积大小和氧化还原性质密切相关;其中,负载型钙钛矿La0.8Ce0.2CoO3/CeO2催化剂在300℃时催化氧化NO的转化率达78%。在添加CeO2作载体后,不仅改善了非负载性钙钛矿的低温活性,而且抗硫性能也显著提高。     

不同方法制备的CeO2-ZrO2体系结构研究

采用不同方法制备了几种CeO2-ZrO2二元氧化物体系,并用XRD、BET、XPS等技术研究了各个体系中氧化铈与氧化锆的存在状态.结果表明以773K焙烧过的氧化锆为载体,浸渍Ce(NO3)3溶液制得的CeO2/ZrO2体系中,氧化铈单层分散于氧化锆的表面,分散阈值约为0.03gCeO2/gZrO2.以水合氧化锆为载体,浸渍Ce(NO3)3溶液制得CeO2-ZrO2固溶体,但用此法制备的固溶体样品与用共沉淀法制备的样品不同.共沉淀法得到的是均一固溶体,浸渍法得到的是富锆固溶体和富铈固溶体的混合物;而且浸渍法制备的样品表面Ce/Zr原子比高,热稳定性好.     

制备方法对CuO-CeO2/ZrO2催化CO氧化性能的影响

以ZrO2为载体、采用不同的浸渍次序制备了3种CuO-CeO2/ZrO2催化剂并在不同的温度(500,650和800℃)下进行焙烧,利用X射线衍射(XRD)、程序升温还原(H2-TPR和CO-TPR)及CO程序升温脱附(CO-TPD)技术对所制备的催化剂进行了表征,并采用色谱流动法考察了其催化CO低温氧化反应性能。结果表明,当焙烧温度为650℃时,3种催化剂的CO催化氧化活性均最佳,且三者的催化活性大小顺序为:CuO/CeO2/ZrO2>CuO-CeO2/ZrO2>CeO2/CuO/ZrO2。结合催化剂的表征和活性测试结果,我们认为高分散的CuO是CO的吸附中心,有利于CO的低温氧化反应,而大颗粒的CuO几乎对CO没有吸附作用,不利于CO的低温氧化反应。在3种催化剂中,CuO/CeO2/ZrO2催化剂具有最佳的低温还原特性和最大的CO2脱附峰面积,相应地具有最佳的催化氧化活性。     

Pt/CexZr1-xO2催化剂上丙烷完全氧化性能研究

采用沉淀法制备了ZrO2,CeO2和Ce0.7Zr0.3O2载体,并用浸渍法制备负载型Pt催化剂。考察了500和900℃焙烧催化剂的丙烷完全氧化性能和水汽对丙烷氧化反应的影响。对于500℃焙烧的催化剂,催化剂的丙烷氧化活性顺序为:Pt/ZrO2-500>Pt/CeO2-500>Pt/Ce0.7Zr0.3O2-500;而经900℃焙烧的催化剂活性顺序为:Pt/ZrO2-900>Pt/Ce0.7Zr0.3O2-900>Pt/CeO2-900。反应气氛中水汽的存在对两种Pt/ZrO2催化剂的活性均有抑制作用(T50温度均提高了10~15℃);而对于Pt/CeO2-500催化剂有抑制作用(T50温度提高10℃),但对Pt/CeO2-900催化剂活性有促进作用(T50温度下降25℃);对于两种Pt/Ce0.7Zr0.3O2催化剂活性具有促进作用(T50温度均下降5~25℃)。表征结果表明催化剂的活性与其表面Pt物种价态密切相关,催化剂表面上Pt0物种有利于活性的提高。Pt/Ce0.7Zr0.3O2-500催化剂中只含有氧化态Pt物种(Pt^2+),而Pt/Ce0.7Zr0.3O2-900催化剂中则含有部分金属态Pt物种,因此其活性高于Pt/Ce0.7Zr0.3O2-500催化剂。     

CeO2-ZrO2-La2O3-Al2O3 composite oxide and its supported palladium catalyst for the treatment of exhaust of natural gas engined vehicles

Composite supports CeO2-ZrO2-Al2O3 (CZA) and CeO2-ZrO2-Al2O3-La2O3 (CZALa) were prepared by co-precipitation method. Palladium catalysts were prepared by impregnation and their purification ability for CH4, CO and NOx in the mixture gas simulated the exhaust from natural gas vehicles (NGVs) operated under stoichiometric condition was investigated. The effect of La2O3 on the physicochemical properties of supports and catalysts was characterized by various techniques. The characterizations with X-ray diffraction (XRD) and Raman spectroscopy revealed that the doping of La2O3 restrained effectively the sintering of crystallite particles, maintained the crystallite particles in nanoscale and stabilized the crystal phase after calcination at 1000 ℃. The results of N2-adsorption, H2-temperature-programmed reduction (H2-TPR) and oxygen storage capacity (OSC) measurements indicated that La2O3 improved the textural properties, reducibility and OSC of composite supports. Catalytic activity testing results showed that the catalysts exhibit excellent activities for the simultaneous removal of methane, CO and NOx in the simulated exhaust gas. The catalysts supported on CZALa showed remarkable thermal stability and catalytic activity for the three pollutants, especially for NOx. The prepared palladium catalysts have high ability to remove NOx, CH4 and CO, and they can be used as excellent catalysts for the purification of exhaust from NGVs operated under stoichiometric condition. They also have significant potential in industrial application because of their high performance and low cost.     

Catalytic methanol decomposition to carbon monoxide and hydrogen over Pd/CeO2-ZrO2-La2O3 with different Ce/Zr molar ratios

The catalytic behaviors of Pd (1.4 wt%) catalysts supported on CeO₂-ZrO₂-La₂O₃ mixed oxides with different Ce/Zr molar ratios were investigated for methanol decomposition. Nitrogen adsorption-desorption (BET), X-ray photoelectron spectroscopy (XPS), H₂ temperature-programmed reduction (H₂-TPR), X-ray diffraction (XRD) and Pd dispersion analysis were used for their characterization. Pd/Ce_0.76Zr_0.18 La_0.06O_1.97 catalyst showed the highest BET surface area, best Pd dispersion capability and strongest metal-support interaction. Moreover, XPS showed that there was lattice defect oxygen or mobile oxygen. According to the result of O 1s measurements the lattice defect oxygen or mobile oxygen helped to maintain Pd in a partly oxidized state and increased the activity for methanol decomposition. The Pd/Ce_0.76Zr_0.18La_0.06O_1.97 catalyst exhibited the best activity. A 100% conversion of methanol was achieved at around 260 °C, which was about 20-40 °C lower than other catalysts     

吸附相反应技术制备MnOx/CeO2/SiO2催化剂及其低温选择性催化还原Nox

采用吸附相反应技术制备得到了MnO_x/CeO₂/SiO₂催化剂,通过X 射线衍射（XRD）、透射电子显微镜（TEM）、高分辨透射电子显微镜（HRTEM）、紫外激光拉曼（Raman）等手段对催化剂进行了表征. HRTEM分析表明活性组分MnO_x与CeO₂都均匀分布在载体SiO₂表面;XRD分析表明Mn₃O₄特征峰随着CeO₂含量的增加逐渐减小至完全消失,CeO₂的加入降低了MnO_x的结晶程度,增加了MnO_x的分散性;Raman光谱表明催化剂表面的Mn离子能够进入CeO₂晶格,激发出空穴氧,随着CeO₂负载量的增加,催化剂氧空穴浓度先升高后降低.以NH₃为还原剂,考评催化剂的NO_x低温选择性催化还原（SCR）性能,催化剂催化活性随CeO₂负载量增加先升高后降低,与催化剂氧空穴浓度变化规律一致,说明催化剂活性受氧空穴浓度影响,氧空穴浓度升高,催化剂催化活性升高.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

Pt/MOx(M=Ni,Fe,Co,Ce)催化剂上CO氧化反应中抗H2O与CO2的性能研究

我们研究了4种负载型Pt催化剂（1Pt/NiO、1Pt/FeO_x、1Pt/Co₃O₄和Pt/CeO₂）上不同反应条件下CO氧化活性及抗H₂O和CO₂性能.发现反应气氛中CO₂的加入与CO形成了竞争吸附,并在催化剂表面形成了碳酸盐物种堵塞了活性位,从而导致催化剂失活.反应气氛中H₂O的加入对1Pt/CeO₂催化剂的活性有所抑制,但对1Pt/FeO_x、1Pt/NiO和1Pt/Co₃O₄催化剂的活性却有促进作用.在1Pt/FeO_x和1Pt/CeO₂催化剂上的分步反应实验和动力学研究表明,尽管H₂O的加入在两种催化剂上均与CO形成了竞争吸附,但在1Pt/FeO_x催化剂上H₂O在载体表面解离形成的羟基更易与CO反应,开辟了新的反应途径,从而提高了反应性能.此外,H₂O的加入能有效分解该催化剂上的碳酸盐物种,从而保持了其稳定性.     

Selective catalytic reduction of NO with CO on Pt/W–Ce–Zr catalysts

Various Pt catalysts (Pt/ZrO₂, Pt/CeO₂, Pt/CeZrO, Pt/WO₃/ZrO₂ and Pt/WO₃/CeZrO) were prepared and characterized, and their catalytic reduction reactions of NO by CO, with or without the presence of excess oxygen, were investigated. The results of temperature-programmed experiments showed that CO could be easily oxidized over Pt/CeO₂ and Pt/CeZrO while the introduction of WO₃ into the catalyst (Pt/WO₃/CeZrO) inhibited the reduction of catalyst surface; NO could not dissociate over those catalysts in oxidized state but after CO reduction at a low temperature, NO dissociation took place only over Pt/CeO₂ and Pt/CeZrO catalysts. For NO + CO reaction, those easily reduced catalysts Pt/CeO₂ and Pt/CeZrO exhibited better catalytic performances, and NO could be rapidly converted below 350 °C. For the reaction with the presence of excess O₂, the NO conversions were significantly inhibited, but better NO conversions were obtained over the tungstate-contained catalysts when compared with Pt/CeO₂ and Pt/CeZrO. The higher activities of Pt/W–Ce–Zr catalysts were attributed to their high acidities.     

制备方法对CuO/CeO_2-ZrO_2催化CO低温氧化活性的影响

采用微波加热分解法(一步法)和微波加热处理共沉淀+浸渍法(两步法)制备了CuO/CeO2-ZrO2催化剂,并对其进行了X射线衍射、低温氮气吸附/脱附和程序升温还原等表征,采用色谱流动法考察了催化剂的催化CO低温氧化性能.结果表明,一步法比两步法更有利于使催化剂表面CuO高度分散,CuO与CeO2-ZrO2间的相互作用更强,CuO更容易被还原,从而具有更高的催化CO氧化活性.与CeO2-ZrO2有相互作用的高分散和小颗粒CuO有利于催化剂活性的提高,与CeO2-ZrO2无相互作用的大颗粒CuO对催化剂的活性有抑制作用.     

Monolith Manganese-Based Catalyst Supported on ZrO2-TiO2 for NH3-SCR Reaction at Low Temperature

Monolith catalysts were prepared using TiO₂ and ZrO₂-TiO₂ as supports with MnO₂ as active component and Fe₂O₃ as promoter. The catalytic activities at low temperature and stability at high temperature for selective catalytic reduction of NO_x with NH₃ (NH₃-SCR) in the presence of excessive O₂ were studied after the catalysts calcined at different temperatures. The catalysts were characterized by X-ray diffraction (XRD), specific surface area measurements (BET), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results indicated that the catalyst supported on ZrO₂-TiO₂ had excellent stability at high temperature, and possessed high specific surface area and oxygen storage capacity, and had strong redox property. The results of the catalytic activities indicated that the monolith manganese-based catalyst using ZrO₂-TiO₂ as support had evidently improved the activity of NH₃-SCR reduction reaction at low temperature, and it showed great potential for practical application.     

国产航空煤油裂解催化剂Pt/ZrxTixAl1-2xO2的性能

采用共沉淀法制备了一系列Zr_xTi_xAl_1-2xO₂复合氧化物载体材料,考察了其作为裂解催化剂载体对航空煤油裂解反应的影响.?采用全自动吸附仪、X射线衍射、扫描电镜/能谱仪联用、NH₃-程序升温脱附等手段对催化剂进行了表征.?结果表明,当ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂具有最大的比表面积和孔容;具有最强的表面酸性和最集中的强酸中心密度,且具有良好的再生功能.?实验结果表明,载体ZrO₂：TiO₂：Al₂O₃质量比为1：1：3时催化剂上650?℃裂解产气量较热裂解提高了2.1倍,700?℃时提高1.4倍.?另外,该系列载体材料经1000?℃焙烧5?h后,所制得的催化剂几乎失去了催化活性.     

Catalytically Promoted NOx Sorption by ZrO2-Based Oxides

Metal promoted zirconia-based oxide sorbents, such as Pt–ZrO₂/Al₂O₃ for NO _x have been investigated. To clarify the role of the catalyst component, sorption of NO and NO₂ was compared using the samples with and without Pt. The catalytic oxidation of NO to NO₂ and successively to nitrate ions is an important role for the Pt catalyst. The experimental results indicate that a high-temperature calcination is essential to remove residual Cl from Pt–ZrO₂–Al₂O₃ prepared from H₂PtCl₆ in order to provide more active NO _x sorption sites. Of M–ZrO₂–Al₂O₃ samples investigated, ruthenium as well as Pt demonstrated relatively good performance as a catalyst component in the sorbent. The FT-IR spectra after sorption of NO and NO₂ demonstrated a strong band attributed to stored nitrate ions. The Pt catalyst was more resistant to sulfur poisoning than a base metal catalyst. However, the NO _x sorptive capacities of the Pt–ZrO₂/Al₂O₃ sorbents were expected to be deteriorated in dilute SO₂ as far as observed from FT-IR spectra.