用对氨基苯酚改性的碳纳米管糊电极同时测定羟胺和苯酚(英文)

A carbon paste electrode that was chemically modified with multiwall carbon nanotubes and p-aminophenol was used as a selective electrochemical sensor for the simultaneous detection of hydroxylamine (HX) and phenol. Cyclic voltammetry, double potential-step chronoamperometry, square wave voltammetry (SWV), and electrochemical impedance spectroscopy were used to investigate the use of p-aminophenol in the carbon nanotubes paste matrixes as a mediator for the electrocatalytic oxidation of HX and phenol in aqueous solution. The coefficient of electron transfer and catalytic reaction rate constant were determined using the electrochemical methods. Under optimized conditions, the electrocatalytic oxidation current peaks for HX and phenol increased linearly with concentration in the range of 0.5-180.0 and 10.0-650.0 μmol/L for HX and phenol, respectively. The detection limits for HX and phenol were 0.15 and 7.1 μmol/L, respectively. The anodic potential peaks of HX and phenol were separated by 0.65 V in SWV. Because of good selectivity and sensitivity, the present method provides a simple method for the selective detection of HX and phenol in practical samples such as water samples.     

Addition Mechanisms of Phenol toward Formaldehyde under Acidic Condition： a Theoretical Investigation

The reaction mechanisms of phenol with formaldehyde in the first and second addition at the ortho- and para-position in acid solution were theoretically investigated at the PW91/DNP level with solvent effects included. The reaction of phenol with protonated methanediol firstly forms an adduct intermediate, via a SN2 mechanism with a water molecule as the leaving group. From the adduct intermediate, there are two reaction channels involving a proton transfer to form the addition products. One is that a proton directly transfers via a four-membered ring transition state with a notable energy barrier (Four-member mechanism). Another mechanism involving a water molecule as catalyst to mediate the proton transfer (WCP mechanism), is a barrierless process, indicating that the formation of the adduct intermediate, the first reaction step, is rate-limiting. The reaction products are free hydroxymethyl phenols and/or hydroxybenzy carbocation (HOC6H4CH2+) which plays an important role in the following formation of methylene and methylene ether linkages. The second addition reactions between formaldehyde and hydroxymethyl phenol at all possible reaction sites of the phenol ring in acid solution were also investigated and discussed.     

Vapor-Phase Alkylation of Phenol with Tert-butyl Alcohol Catalyzed by H3PO4/MCM-41

 The catalytic performance of Al-MCM-41 containing 5?5 wt% H3PO4 was studied for the vapor phase alkylation of phenol with tert-butyl alcohol (TBA) from 383 to 493 K. 4-Tert-butyl phenol was produced as the main product with moderate selectivity. The product distribution depends on the reaction temperature, number of acid sites, and the Br鰊sted to Lewis sites ratios. A lower molar ratio of reactants (TBA/phenol = 2) and a higher space velocity facilitated the production of 4-tert-butyl phenol. The influence of various parameters such as temperature, reactant feed molar ratio, feed rate, and time on stream were investigated for conversion yield and product selectivity.     

Esterification of Glycerol by Oleic Acid and Selective Hydrogenation of Oleic Acid Methylester Over Acid and Ru-Sn-B Supported Mesoporous AlMCM-41

Demand for large pore size molecular sieves has given rise to great interests in a new family of silica-based mesoporous materials designated as M41s, which expand typical molecular sieves into an extra-large pore range and generate the potential for the applications of these materials in catalysis and sorption for very bulky molecules1-6. MCM-41 possesses a hexagonal arrangement of uniform mesopore ranging from 15 to 100 ? and can be prepared with varied Si/Al ratios. The investigations of …     

Synthesis and Characterization of Magnesium Substituted Aluminophosphate Molecular Sieves with AEL Structure

MAPO-11 molecular sieves were synthesized by hydrothermal methods. The influence of precursor of magnesium, Mg/Al ratio, synthesis temperature, synthesis time and the type of template on the formation and properties of MAPO-11 molecular sieves was examined. The samples were characterized by the techniques of X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric/differential thermogravimetric analysis (TG-DGA), etc. The results show that the shape and size of crystal were influenced by the precursor of Mg, the Mg/Al ratio and the type of template, and the TG-DGA analysis shows that MAPO-11 molecular sieves as-synthesized have poor thermal stability.     

Preparation and characterization of vanadium(IV) oxide supported on SBA-15 and its catalytic performance in benzene hydroxylation to phenol using molecular oxygen

Preparation of dispersed transition metal oxides catalyst with low oxidation state still remains a challenging task in heterogeneous catalysis.In this study,vanadium oxides supported on zeolite SBA-15 have been prepared under hydrothermal condition using V 2 O 5 and oxalic acid as sources of vanadium and reductant,respectively.The structures of samples,especially the oxidation state of vanadium,and the surface distribution of vanadium oxide species,have been thoroughly characterized using various techniques,including N 2-physisorption,X-ray diffraction(XRD),transmission electron microscopy(TEM),X-ray photoelectron spectroscopy(XPS),UV-visible spectra(UV-Vis) and UV-visible-near infrared spectra(UV-Vis-NIR).It is found that the majority of supported vanadium was in the form of vanadium(IV) oxide species with the low valence of vanadium.By adjusting hydrothermal treatment time,the surface distribution of vanadium(IV) oxide species can be tuned from vanadium(IV) oxide cluster to crystallites.These materials have been tested in the hydroxylation of benzene to phenol in liquid-phase with molecular oxygen in the absence of reductant.The catalyst exhibits high selectivity for phenol(61%) at benzene conversion of 4.6%,which is a relatively good result in comparison with other studies employing molecular oxygen as the oxidant.     

可见光下改性的纳米孔二氧化硅(LUS-1)光催化苯直接羟基化合成苯酚(英文)

Fe-g-C3N4-LUS-1 was prepared by the thermal decomposition of dicyandiamide inside the pores of LUS-1 under an inert atmosphere.It was used as a photocatalyst for the hydroxylation of benzene to phenol in sunlight.The catalysts were characterized by Fourier transform infrared spectroscopy,N2 adsorption-desorption,X-ray diffraction,and scanning electron microscopy.In Fe-g-C3N4-LUS-1,a single layer of graphitic carbon nitride(g-C3N4) was formed on the surface of LUS-1.The photocatalytic activity of the iron containing g-C3N4 based catalysts was investigated,and the catalytic activity was remarkably enhanced when the reaction condition was changed from dark to sunlight.The best result was obtained with 20%Fe-g-C3N4-LUS-1 in sunlight.     

异丁烯在不同硅铝比的NanZSM-5型分子筛中的吸附：分子模拟研究

Frameworks of NanZSM-5 type zeolites with various Si/A1 ratios have been constructed and optimized with molecular dynamic quench simulation. The results show that the structure parameters of NanZSM-5 type zeolite, including the bond length and atomic charges, are consistent with those predicted by ab initio cluster calculations. It was also observed that atomic charges of Si atoms were shifted to higher field in NanZSM-5 type zeolite with lower Si/Al ratio. Then, the adsorption of isobutene on NanZSM-5 with various Si/Al ratios has been investigated using grand canonical ensemble Monte Carlo simulation and Cvff-300-1.01 forcefield. The simulated adsorption amount was in good agreement with the experimental data. Based on these facts, the effects of Si/Al ratio on the adsorption amount and adsorption isotherms of isobutene on NanZSM-5 were predicted. The results indicated that Si/Al ratio was important for the adsorption of isobutene and the adsorption amount was decreased as the Si/Al ratio was increased, which can be explained that the atomic charge of Na^＋ cation would influence greatly the π electrons of the isobutene double bond due to the Coulomb force. In addition, the adsorption sites of isobutene and interaction energy of isobutene with NanZSM-5 were also discussed.     

Fluorescence enhancing by alkaline degradation of tetracycline antibiotics and its application

Tetracycline antibiotics could be degraded after being beated in boiling-water bath in alkaline solution (in KOH medium).The fluorescence excitation and emission wavelengths of the degradation products changed and the fluorescence intensity increased by 5-190 folds as compared with that of antibiotics themselves It was considered that there occurred a nucleophilic ring rupture reaction to form the degradation products with lactome structure The mteraction of the lone pair electrons of oxygen on the degradation products with the conjugated π electrons induced the in crease of the delocalization for the conjugated electron system in the molecule and thus enhanced the fluorescence intensity.     

Catalytic performance of hierarchical H-ZSM-5/MCM-41 for methanol dehydration to dimethyl ether

Micro-mesoporous composite molecular sieves H-ZSM-5/MCM-41 were prepared by the hydrothermal technique with alkali-treated H-ZSM-5zeolite as the source and characterized by scanning electron microscopy,transmission electron microscopy,energy dispersive spectroscopy,X-ray diffraction,N2 adsorption-desorption measurement and NH3 temperature-programmed desorption.The catalytic performances for the methanol dehydration to dimethyl ether over H-ZSM-5/MCM-41 were evaluated.Among these catalysts,H-ZSM-5/MCM-41 prepared with NaOH dosage (nNa/nSi) varying from 0.4 to 0.47 presented excellent catalytic activity with more than 80%methanol conversion and 100%dimethyl ether selectivity in a wide temperature range of 170—300℃,and H-ZSM-5/MCM-41 prepared with nNa/nSi=0.47 showed constant methanol conversion of about 88.7%,100% dimethyl ether selectivity and excellent lifetime at 220℃.The excellent catalytic performances were due to the highly active and uniform acidic sites and the hierarchical porosity in the micro-mesoporous composite molecular sieves.The catalytic mechanism of H-ZSM-5/MCM-41 for the methanol dehydration to dimethyl ether process was also discussed.     

微波辐射法合成SAPO-5分子筛中硅铝比对产物结晶度和甲苯吸附性能的影响

采用硅溶胶作硅源, 用微波辐射法在酸性条件下(pH=4.5-5.0)合成了SAPO-5分子筛, 利用X射线衍射(XRD), 傅立叶变换红外光谱(FT-IR), 扫描电镜(SEM)和Brunauer-Emmett-Teller (BET)比表面积分析对样品的结晶度、形貌和比表面等进行表征, 考察了晶化原料硅铝比对分子筛结晶度和晶体颗粒长径比(c/a)的影响, 测定了分子筛对甲苯的吸附性能. 结果显示, 采用微波辐射法合成的SAPO-5分子筛, 在硅铝摩尔比为0.50附近生成产物的结晶度最好, 晶体颗粒的长径比最小(约为1.0). 尽管不同硅铝比条件下得到的样品比表面测定结果变化不大, 但对甲苯的吸附实验显示, 在硅铝比为0.50时样品的吸附速率和饱和吸附量均达到了最大值. 这与表征所得的结晶度和长径比的变化一致, 即结晶度好,长径比小的SAPO-5分子筛具有更好的甲苯吸附性能.     

分子筛对葡萄糖淀粉酶的吸附性能研究

测定了黑曲霉葡萄糖淀粉酶(E.C.3.2.1.3)在三种改性的、具有中孔和大孔的分子筛上的吸附等温线并将吸附量和吸附等温线的形状与分子筛的等电点、孔容、孔径及酸性相关联。讨论了孔结构和不同酶吸附量对分子筛固定化葡萄糖淀粉酶活力的影响。发现葡萄糖淀粉酶在再造孔分子筛上的单层饱和吸附量与再造孔的方法密切有关,三种不同再造孔方法制得的分子筛具有不同的骨架Si/Al比、不同的孔分布和比表面积。不同的Si/Al比导致不同的酸性质和等电点。酶吸附量与载体的表面酸性、等电点以及吸附时溶液的pH有关。分子筛对酶的吸附以静电作用为主。其次,当中孔孔径和孔容越大时,单层饱和吸附量亦越大。随着分子筛对葡萄糖淀粉酶的吸附量增加,固定化酶的活力增大,但固定化酶的比活力随吸附量的增加、中孔孔容和孔径的减小而下降。     

杂原子介孔分子筛Me-HMS催化酯交换合成碳酸二苯酯

以水热合成法制备了杂原子介孔分子筛Me-HMS(Me指金属杂原子),用于催化碳酸二甲酯与苯酚酯交换合成碳酸二苯酯的反应.小角度的X射线衍射显示,所有样品均具有典型的HMS介孔结构.Me-HMS中,Ti-HMS显示最好的催化性能,其活性与骨架钛含量密切相关,当溶胶中Ti/Si比达1/30时,骨架钛趋于饱和,苯酚转化率达到最大值31.4%,酯交换选择性为99.9%.     

无铝V-β分子筛的合成、表征及催化性能研究

采用水热晶化法在SiO2-V2O5-(TEA)2O-NH4F-H2O体系中合成了无铝V-β分子筛,运用XRD,IR,UV-Vis漫反射,TG/DTA和SEM等技术表征了样品的物理化学特性,证明样品具有BEA拓扑结构,结晶良好,且钒原子进入了分子筛骨架. 探讨了反应混合物组成对V-β分子筛晶化的影响,在以H2O2为氧化剂的苯酚羟基化反应中,考察了V-β分子筛的催化氧化性能.     

M-HMS的合成、表征及在苯酚羟化反应中的催化性能

HMS-中孔分子筛;二酚;M-HMS的合成、表征及在苯酚羟化反应中的催化性能     

V-AlPO5分子筛催化苯直接羟基化制苯酚

采用水热法合成了V-AlPO5分子筛催化剂,通过XRD表征确定其具有AlPO-5微孔分子筛的晶体结构。不同合成条件对V-AlPO5分子筛的催化活性有一定影响,优化合成条件下制备的V-AlPO5分子筛,在以过氧化氢为氧化剂的苯羟基化制苯酚反应中表现出较佳的催化活性。反应温度55 ℃,乙腈6 mL,苯10 mmol,质量分数35%过氧化氢15 mmol,氧化剂用量0.2 g,共还原剂抗坏血酸0.2 g,反应24 h,苯酚收率可达16.1%,选择性为86.8%。     

AlMCM-41介孔分子筛的合成及表征

以拟薄水铝石为铝源、水玻璃为硅源、十六烷基三甲基溴化铵为模板剂,在110℃时水热晶化合成了含Al的MCM-41介孔分子筛.采用X射线衍射(XRD)、N2吸附-脱附、固体29Si、27Al魔角旋转核磁共振技术(MASNMR)、扫描电镜(SEM)及吡啶吸附傅里叶变换红外(FTIR)光谱技术对AlMCM-41分子筛进行了表征.结果表明:AlMCM-41分子筛具有六方排列的孔道结构,同时具有很高的相对结晶度、比表面积和孔容,且孔分布单一;AlMCM-41分子筛中Si原子在骨架内键合的程度更高,使AlMCM-41分子筛具有更好的骨架晶化程度;同时具有四配位骨架铝,使AlMCM-41介孔分子筛具有适当的酸性.     

AlMCM-48介孔分子筛对萘异丙基化反应的活性

2－烷基萘和2,6－二烷基萘是很有价值的化学品,2－烷基萘可用于染料,药物,香料等精细化学品的生产,2,6－二烷基萘是生产新型聚合材料的重要原料,以煤焦油中萘 原料经傅－克反应可获得烷基萘,工业上传统的液相反应用H2SO4,H4PO4,AlCl3等作催化剂[1],由于存在腐蚀性强,产物分离难,污染重等弊病,人们极力探求性能优良,环境友好的新型催化剂,各种沸石分子筛如ZSM－5,HY,HM,β－沸石等对萘 烷基化反应的催化性能都有探讨^[2-6],据报道,用H－ZSM－5催化萘的甲基反应显示较高的选择性^[2],n(2-甲基萘）／n(1-甲基萘）达到8;（2,6－二甲基萘＋2,7－二甲基萘）在二取代产物中达到80．8％,但萘的转化率较低,约10％,由于H－ZSM－5的孔径较小,它对萘的异丙基化反应几乎无活性[6],HY,Hβ对萘的异丙基化反应活性较高,但选择性差,n(2,6-二甲基萘／2,7－二甲基萘）＝1,HM对萘的异丙基化反应选择性较高,而萘的转化率不高,约30％^[3-6],掺要Ce的丝光沸石选择性和活性都有所提高[7],本文研究了用后处理方法固载铝的AlMCM-48介孔分子筛对萘的异丙基化反应的催化作用,考察了Si/Al对反应的影响。β     

过氧化氢直接氧化苯制备苯酚的多相催化研究进展*

作为一种绿色、洁净的氧化剂,使用过氧化氢直接氧化苯来制备苯酚的过程极具吸引力。综述了分子筛、碳基材料、金属氧化物、金属有机框架等多相催化剂在氧化苯制备苯酚反应中的应用,主要讨论了催化剂的合成路线、反应机理和催化性能,希望能为新的多相催化体系的合理设计提供有益的视角。     

在蒸气相中合成中孔分子筛MCM—41及其孔结构参数的表征

在水蒸气中，由含表面活性剂十六烷基三甲基溴化铵的无定形凝胶合成出Ｓｉ－ＭＣＭ－４１和Ａｌ－Ｓｉ－ＭＣＭ－４１分子筛纯相，研究了它们的合成条件。