有机功能化α-Al2O3陶瓷中空纤维表面合成高性能分离氢用NaA分子筛膜

通过浸渍3-氨丙基甲基二乙氧基硅烷(ADMS)对α-Al₂O₃中空纤维载体进行有机功能化改性, 使载体表面带正电, 利用NaA分子筛晶种负电性与功能化载体之间的静电吸附机理进行预涂晶种, 采用微波加热-二次生长法于载体表面合成了NaA分子筛膜. 采用X射线衍射(XRD)、zeta 电位、扫描电子显微镜(SEM)等分析手段和气体渗透实验对NaA分子筛膜进行了表征. 考察了未改性NaA分子筛膜与改性NaA分子筛膜的形貌、结构和气体渗透性能差异. XRD结果表明载体表面只有NaA分子筛生成; zeta 电位分析表明NaA分子筛晶种及分子筛前驱体与有机功能化载体电位相反, 存在静电吸附作用; SEM结果显示改性NaA分子筛膜表面颗粒相互联结呈孪生态, 膜厚约5 μm, 膜层致密、均匀、平整; 在不同温度下对H₂、O₂、N₂和C₃H₈进行气体渗透测试,35 °C条件下改性NaA分子筛膜对H₂的渗透率仅为3.6×10^-7 mol·m^-2·s^-1·Pa^-1, 较未改性NaA分子筛膜的渗透率(4.0×10^-7 mol·m^-2·s^-1·Pa^-1)低, 而改性NaA分子筛膜的H₂/C₃H₈理想分离系数则高达11.25, 远大于未改性NaA分子筛膜的H₂/C₃H₈理想分离系数(5.06).     

以催化裂化废催化剂为原料合成NaY分子筛的研究

针对催化裂化(FCC)废催化剂的回收利用问题,提出了一种废催化剂再利用的方法,即以FCC废催化剂为铝源,合成时只补充部分硅源,采用自制的高效NaY沸石导向剂,水热合成NaY分子筛。同时,以普通的化工原料合成了对比试样Y型分子筛。讨论了不同的FCC废催化剂预处理方式对合成产物性能的影响,发现以经过碱熔活化处理的废催化剂为原料合成的Y分子筛拥有更高的结晶度和纯度。采用X射线衍射、热分析、程序升温脱附法(NH3-TPD)和N₂静态容量吸附法对结晶产物和对比样品的晶体结构,热稳定性、酸性质、比表面积以及孔分布进行了表征。结果显示,以FCC废催化剂为原料完全可以合成出与普通原料性能接近的NaY分子筛。其BET比表面积可以达到615 m²·g^-1,孔体积可达0.38 cm³·g^-1,孔径集中在0.51 nm左右。     

斜发沸石的合成研究

采用水热法，分别在物质量的比为2.1Na₂O∶10SiO₂∶Al₂O₃∶110.1H₂O和1.05K₂O∶1.05Na₂O:12SiO₂∶Al₂O₃∶250H₂O的条件下合成出较高纯度斜发沸石，研究了斜发沸石合成的各种影响因素。结果表明，在140、160和180 ℃条件下均能合成出斜发沸石，且提高温度可以缩短斜发沸石的晶化时间；反应混合物的硅铝物质量的比应控制在10～12之间；碱度的降低会导致晶化时间延长，过高的碱度则导致晶种溶解；反应混合物中K⁺的存在利于斜发沸石的晶化。合成斜发沸石对海水中K⁺饱和吸附量达 38.60 mg·g^-1以上，其吸附性能显著优于文献报导的天然斜发沸石。     

微孔/介孔复合分子筛的合成及其对CO2的吸附性能

采用两步晶化法将合成的沸石前驱液(S)或沸石固体粉末(P)经不同浓度(c)的NaOH处理后, 分别以表面活性剂十六烷基三甲基溴化铵(CTAB)软模板或介孔炭(Meso-C)硬模板为导向剂, 自组装合成S-β-MCM41(c)、P-β-MCM41(c)、P-ZSM-MCM41(c)、P-ZSM-C系列微孔/介孔复合分子筛. 考察了沸石分子筛种类、碱处理液浓度以及介孔模板剂对合成复合分子筛结构与性能的影响. X射线衍射(XRD)、透射电子显微镜(TEM)和氮气吸附-脱附表征结果表明产物具有微孔/介孔多级孔结构. 该材料对CO₂的吸附能力比纯微孔或介孔材料均有明显提高, 其中P-ZSM-MCM41(2)的CO₂吸附容量最大可达1.51 mmol·g^-1, 为ZSM-5沸石吸附量的两倍多.     

基于1, 1′-苯乙炔-3, 3′, 5, 5′-四羧酸微孔铜配位聚合物的合成和气体吸附性质

本文报道了配合物[Cu₂(EBTC)(H₂O)₂]·8H₂O·DMF·DMSO(1, EBTC=1, 1′-乙炔基苯-3, 3′, 5, 5′-四羧酸根;DMF=N, N-二甲基甲酰胺;DMSO=二甲基亚砜)的合成、晶体结构和吸附性质。1拥有内径为0.85 nm和0.85 nm×2.15 nm的两种孔洞, 分别被6个和12个四羧酸根桥联的[Cu₂(CO₂)₄]螺旋桨式结构围绕, 并被EBTC连接成三维超分子结构, 该结构拥有可容纳溶剂分子的一维孔道。1为(3, 4)-连接的fof(sqc1575)拓扑结构, 具有非常大的孔体积, 其值高达单位晶胞体积的72.8%。去除溶剂分子后的1a表现出永久孔性, 其Langmuir表面积为2844 m²·g^-1, BET 表面积为1 852 m²·g^-1。它对H₂、CO₂、CH₄和C²H₂具有可观的气体吸附量和相对较高的吸附焓。特别是, 在迄今所有已报道的孔性金属-有机材料中, 1a在273 K、1.0×10⁵ Pa下, 表现出最高的乙炔吸附量(252 cm³·g^-1)和很高的吸附焓(吸附量为1 mmol·g^-1时的吸附焓为34.5 kJ·mol^-1)。     

酸处理对CuY催化剂孔结构及氧化羰基化性能的影响

对NaY分子筛(n_Si/n_Al=2.65)进行了草酸脱铝处理并作为载体采用液相离子交换法制备CuY催化剂, 应用于常压甲醇氧化羰基化合成碳酸二甲酯(DMC)反应。NaY分子筛及其CuY催化剂通过N₂低温吸附-脱附、透射电子显微镜、X射线衍射、²⁹Si固体核磁共振、NH₃吸附程序升温脱附、吡啶吸附红外光谱、H₂程序升温还原、原子吸收等方法进行表征。研究结果表明, 酸处理NaY分子筛后, 骨架铝被脱除, 导致骨架n_Si/n_Al比增加、相对结晶度降低并产生介孔, 有利于产物分子的扩散, 从而影响催化活性。采用4 h、2 mol·L^-1草酸处理NaY分子筛作为载体制备的CuY催化剂显示出较高的催化性能, DMC时空收率和甲醇转化率分别从103.6 mg·g^-1·h^-1和6.3%增加到184.9 mg·g^-1·h^-1和10.2%。产生的介孔能够促进催化剂中铜活性位的可接近性及反应物分子和产物分子的扩散。     

酸处理对CuY催化剂孔结构及氧化羰基化性能的影响

对NaY分子筛(n_Si/n_Al=2.65)进行了草酸脱铝处理并作为载体采用液相离子交换法制备CuY催化剂,应用于常压甲醇氧化羰基化合成碳酸二甲酯(DMC)反应。NaY分子筛及其CuY催化剂通过N₂低温吸附-脱附、透射电子显微镜、X射线衍射、²⁹Si固体核磁共振、NH₃吸附程序升温脱附、吡啶吸附红外光谱、H₂程序升温还原、原子吸收等方法进行表征。研究结果表明,酸处理NaY分子筛后,骨架铝被脱除,导致骨架n_Si/n_Al比增加、相对结晶度降低并产生介孔,有利于产物分子的扩散,从而影响催化活性。采用4 h、2 mol·L^-1草酸处理NaY分子筛作为载体制备的CuY催化剂显示出较高的催化性能,DMC时空收率和甲醇转化率分别从103.6 mg·g^-1·h^-1和6.3%增加到184.9 mg·g^-1·h^-1和10.2%。产生的介孔能够促进催化剂中铜活性位的可接近性及反应物分子和产物分子的扩散。     

无有机模板剂水热合成Co同晶取代的丝光沸石分子筛

在硅酸钠、硫酸铝、硝酸钴和氢氧化钠的全无机体系条件下, 采用无有机模板剂水热法合成了Co同晶取代的丝光沸石分子筛. 通过粉末X射线衍射(XRD)、扫描电子显微镜(SEM)、电感耦合等离子体(ICP)光谱、氮气吸附、紫外-可见(UV-Vis)光谱、热重(TG)分析等手段对所得固体产物的织构性质以及钴在分子筛中的存在状态进行了表征. 结果表明, 该方法成功地将Co离子引入到丝光沸石分子筛的骨架结构中, 未发现骨架外Co物种. 典型的合成条件为n(Co)/n(SiO₂) =0.01-0.04, n(SiO₂)/n(Al₂O₃) =20-50, n(H₂O)/n(SiO₂) =40, n(Na₂O)/n(SiO₂)=0.4, 晶化温度170 °C, 晶化时间3-7 d. 讨论了Na+离子在无有机模板剂合成中的结构导向作用. 全无机体系合成得到的产物无需进行传统的高温煅烧处理, 即可获得开放的微孔孔道, 实现了低成本、低能耗、环境友好的Co-丝光沸石的合成.     

双层SiO2包覆Fe3O4复合材料的制备及其染料吸附性能

采用改进的Stober法合成了多孔结构的双层SiO₂包覆Fe₃O₄复合材料,利用TEM、XRD、VSM和氮吸附-脱附实验对其结构与性能进行分析,进而研究其对染料的吸附性能。研究结果表明,双层SiO₂包覆Fe₃O₄复合材料的比表面积和磁饱和强度分别为308 m²·g^-1和45.5 emu·g^-1;当罗丹明B的初始浓度从25 mg·L^-1提高到250 mg·L^-1时,复合材料对其饱和吸附量从24.0 mg·g^-1增大到112.4 mg·g^-1,而亚甲基蓝的初始浓度从25 mg·L^-1提高到500 mg·L^-1时,对其饱和吸附量从22.0 mg·g^-1增大到235.1 mg·g^-1;随着溶液pH值增大,复合材料对罗丹明B的饱和吸附量增加,而对亚甲基蓝的饱和吸附量变化不明显;温度在20~40 ℃范围内复合材料的吸附量较大。     

双层SiO2包覆Fe3O4复合材料的制备及其染料吸附性能

采用改进的Stober法合成了多孔结构的双层SiO₂包覆Fe₃O₄复合材料,利用TEM、XRD、VSM和氮吸附-脱附实验对其结构与性能进行分析,进而研究其对染料的吸附性能。研究结果表明,双层SiO₂包覆Fe₃O₄复合材料的比表面积和磁饱和强度分别为308 m²·g^-1和45.5 emu·g^-1;当罗丹明B的初始浓度从25 mg·L^-1提高到250 mg·L^-1时,复合材料对其饱和吸附量从24.0 mg·g^-1增大到112.4 mg·g^-1,而亚甲基蓝的初始浓度从25 mg·L^-1提高到500 mg·L^-1时,对其饱和吸附量从22.0 mg·g^-1增大到235.1 mg·g^-1;随着溶液pH值增大,复合材料对罗丹明B的饱和吸附量增加,而对亚甲基蓝的饱和吸附量变化不明显;温度在20~40 ℃范围内复合材料的吸附量较大。     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.