气相燃烧合成纳米复合粒子的形态与结构

在气相燃烧反应器中成功地合成了TiO₂-SiO₂、TiO₂-SnO₂复合粒子。TiO₂-SiO₂复合粒子中TiO₂以金红石型和锐钛型存在，SiO₂以无定型的形式存在。复合结构为SiO₂附着于TiO₂的外部，在Ti∶Si的进料比较大时SiO₂附着于TiO₂的表面，Ti∶Si比值减小到1∶4时，SiO₂包覆全部TiO₂表面。包覆层的厚度大约为6～7nm。TiO₂-SnO₂的复合粒子中同时存在着三种晶体结构SnO₂、金红石型和锐钛型的TiO₂。在复合粒子的表面，TiO₂和SnO₂两种组分分布均匀。通过改变进料方式可以调整复合粒子的结构。     

球形TiO2-Al2O3的制备、结构和理化性能研究

将Ti(SO₄)₂溶于稀盐酸合成酸性钛溶胶，再将其与铝溶胶和六次甲基四胺溶液混合后采用油柱成型法制备了球形TiO₂-Al₂O₃复合氧化物。通过XRD、低温氮吸附-脱附与NH₃-TPD等手段对样品进行表征，结果表明600 ℃焙烧得到的球形TiO₂-Al₂O₃中TiO₂以无定型形式存在;随TiO₂含量的增加，球形TiO₂-Al₂O₃的比表面积、孔容和平均孔径呈增加趋势;TiO₂的引入没有对球形TiO₂-Al₂O₃的强酸和弱酸中心的强度产生影响，弱酸中心数量显著增加，强酸中心数量稍有增加;球形TiO₂-Al₂O₃的堆密度和压碎强度随TiO₂含量的增加而减小，颗粒直径基本保持不变。     

一锅法制备S型异质结光催化剂Fe2O3/Fe2TiO5及其高效降解有机污染物性能

首次采用简单的一锅法制备了Fe₂O₃/Fe₂TiO₅异质结纳米材料。构建S型异质结后,与纯的Fe₂O₃和Fe₂TiO₅相比,Fe₂O₃/Fe₂TiO₅复合材料表现出更高的光催化降解速率和效率。经过2.5 h的光照后,Fe₂O₃/Fe₂TiO₅可以降解接近100%的亚甲基蓝（MB）。在Fe₂O₃/Fe₂TiO₅复合材料中,Fe₂O₃和Fe₂TiO₅之间形成了内建电场,可以促进光生电子-空穴对的分离。因此,具有更高能量的Fe₂TiO₅导带中的电子和具有更高能量的Fe₂O₃价带中的空穴可以得到有效的保留,从而使它们更加有效地扩散到催化剂表面,并参加降解反应。此外,Fe₂O₃/Fe₂TiO₅复合材料具有很好的光催化稳定性。     

Au改性TiO2纳米复合物对人结肠癌细胞的光催化杀伤作用

提出了通过TiO₂表面修饰纳米Au的方法来提高纳米TiO₂光催化杀伤癌细胞的效率. 采用化学还原法合成了Au改性的TiO₂ (Au/TiO₂)纳米复合物, 并研究了不同掺杂量(1 wt%, 2 wt%, 4 wt%)的Au/TiO₂对人结肠癌LoVo细胞的光催化杀伤效应. 结果显示, Au的掺杂大大地提高了TiO₂纳米粒子光催化杀伤结肠癌LoVo细胞的效率, 而且Au掺杂量的高低影响Au/TiO₂光催化杀伤癌细胞的效率, 掺金量为2%的Au/TiO₂对结肠癌LoVo细胞具有最高的光催化杀伤效率. 在光强为1.8 mW/cm²的紫外灯(λ_max＝365 nm)下光照110 min, 50 μg/mL掺金量为2%的Au/TiO₂能够杀死所有的癌细胞, 而同样浓度的TiO₂只能杀死70%的癌细胞.     

微乳法制备纳米TiO2 /SiO2的结构及光催化研究

Nanosized TiO₂ and TiO₂/SiO₂ particles were prepared by hydrolysis of tetrabutyl titanate (TBOT) and tetraethyl orthosilicate (TEOS) in the TX-100 reverse microemulsion. These particles were characterized by TG-DSC, XRD, FTIR, TEM，N₂ adsorption-desorption. Their photocatalytic activity was tested by degradation of methyl orange. The result shows that TiO₂/SiO₂ nanoparticles are with a monodispersed spherical phase and a uniform size distribution，and TiO₂ particles are dispersed on the surface of SiO₂. The band for Ti-O-Si vibration in FTIR was observed, the Ti-O-Si bond increased the stability of anatase TiO₂, suppressed the phase transformation of titania from anatase to rutile. And due to the addition of SiO₂, the average size of titania decreased from 38 nm in pure TiO₂ to 5 nm in TiO₂/SiO₂. It was found, under UV light irradiation, TiO₂/SiO₂ particles showed higher activity than pure TiO₂, and TiO₂/SiO₂(1/1) particles showed the highest photocatalytic activity on the photocatalytic decomposition of methyl orange, which was influenced by crystal structure, particle size, crystallinity and Surface area Characteristics.     

Bi2S3/CdSe共修饰TiO2纳米管膜的构建及其光电化学阴极保护效应

为获得良好光电化学性能的TiO₂半导体复合膜,采用Bi₂S₃和CdSe对TiO₂纳米管膜进行共修饰。以阳极氧化法在Ti表面先制备TiO₂纳米管膜,再通过恒电流电沉积和连续离子层吸附反应在纳米管表面依次沉积CdSe和Bi₂S₃,构建了具有级联能带结构的Bi₂S₃/CdSe共修饰的TiO₂纳米管复合膜。结果表明,Bi₂S₃/CdSe/TiO₂纳米管复合膜对可见光吸收显著增强,光电化学性能大幅度提高。白光照射下,复合膜的光电流密度为670 μA·cm^-2,达到了纯TiO₂纳米管膜的17.6倍。Bi₂S₃/CdSe/TiO₂复合膜作为光阳极可使0.5 mol·L^-1 NaCl溶液中的403不锈钢的电位相对于腐蚀电位下降690 mV,显示出良好的光电化学阴极保护效应。     

Pt / InVO4 / TiO2可见光催化剂的制备及性能研究

采用溶胶-凝胶法制备了Pt / InVO₄ / TiO₂三元体系可见光催化剂。以乙烯为模拟目标分子，评价其光催化活性并与二元体系催化剂Pt / TiO₂ 和InVO₄ / TiO₂进行比较。用DRS，XRD对催化剂的吸收带边和晶型进行了表征。结果表明：Pt / InVO₄ / TiO₂在可见光区（λ>450 nm）的光催化比活性比Pt / TiO相似文献   

核壳结构TiO2@SiO2催化碳酸二甲酯与苯酚酯交换合成碳酸二苯酯

以反相微乳液法和沉淀法相结合制备了核壳结构TiO₂@SiO₂,首次用于碳酸二甲酯与苯酚酯交换合成碳酸二苯酯反应,显示较好的催化活性. 采用200 ℃焙烧的TiO₂@SiO₂,用量0.20 g,反应9 h,苯酚转化率达41.8%,酯交换选择性为100%. 透射电镜显示TiO₂@SiO₂核厚壳薄,TiO₂核直径220-300 nm,SiO₂壳厚度40-60 nm,具有介孔结构. TiO₂@SiO₂对碳酸二甲酯与苯酚酯交换反应有好的重复使用性,使用4次苯酚转化率仍保持在40%以上. TiO₂与SiO₂发生相互作用,Ti进入骨架形成Ti-O-Si键,骨架Ti的形成提高了TiO₂@SiO₂的催化性能.     

SnO2TiO2 复合半导体纳米薄膜的研究进展

本文概述了SnO₂TiO₂ 复合半导体纳米薄膜的发展历史和研究现状,对比分析了“混合”、“核壳”和“叠层”3 种复合薄膜的结构和性能特点,着重论述了叠层结构的SnO₂ /TiO₂复合薄膜的光电化学和光催化特性。结合作者的研究工作,探讨了SnO₂ /TiO₂双层复合薄膜上下层厚度对其光催化活性的影响,指出复合薄膜光催化活性的提高可归因于电子从TiO₂ 向SnO₂ 的迁移。最后对SnO₂ /TiO₂复合薄膜的局限性和发展潜势做一简要分析,强调了该复合薄膜本身的应用特点。     

TiO2纳米线的制备及其光电性能研究

利用在钛箔表面沉积一层TiO₂纳米粒子作为晶种，与NaOH反应，制备了一维物质TiO₂纳米线。并用XRD、SEM、TEM、HRTEM及EDS等分析手段对TiO₂纳米线的成分、形貌、结构进行表征。结果表明，采用该方法制得的TiO₂纳米线直径在20～50 nm左右、长度可达几微米。反应温度能显著影响所得纳米线的形貌。研究了TiO₂纳米线的光电化学性能。随反应温度的升高TiO₂纳米线光电转换效率增大。     

Photocatalytic Effects of Rutile Phase TiO2 Ultrafine Powder with High Specific Surface Area Obtained by a Homogeneous Precipitation Process at Low Temperatures

The photocatalytic characteristics of nanostructured TiO₂ ultrafine powder with rutile phase produced using the homogeneous precipitation process at low temperatures (HPPLT) were compared with those of commercial P-25 TiO₂ powder by flame hydrolysis. The TiO₂ powder by the HPPLT showed much higher photoactivity in the removal rate, showing lower pH values in the solution than the P-25 powder when eliminating metal ions such as Pb and Cu from the aqueous metal-EDTA solutions. This can be inferred as the more rapid photo-oxidation or -reduction of metal ions from the aqueous solution, together with relatively higher efficiencies in the use of an electron-hole pair formed on the surface of the TiO₂ particles under UV light irradiation. Also, in the view of the TiO₂ particle morphology, compared to the well-dispersed spherical P-25 particles, the agglomerated TiO₂ secondary particles by the HPPLT consist of acicular typed primary particles with a thickness in the range of 3–7 nm and the primary particles radialize in all directions, which would be more effective to photocatalytic reactions without the large electron-hole recombination on the surface of the TiO₂ particle under UV light irradiation. It can be, therefore, thought that the higher photoactivity of the rutile TiO₂ powder by the HPPLT in the aqueous solutions results mainly from having a larger surface area by the acicular shaped primary particles with very thin thickness and radialization in all directions.     

Investigation of visible light active Ag sensitized mixed phase TiO2 photocatalyst for solar energy application

Visible photo-active anatase and mixed phase Ag/TiO₂ photocatalysts were prepared using sol–gel method with 1.5 wt% Ag concentration. Due to the large band gap, pristine titania (anatase) is mainly active in the UV light and the photoactivity is limited. But in the presence of both anatase (~3.2 eV) and rutile (~3.0 eV) phases in TiO₂, the catalyst is expected to show enhancement in the photoactivity due to mixed phase junction. The Ag particles are used to act as electron sink and to swiftly transport the photo-generated electrons and, consequently, lessen the recombination rate. The synergistic effect of surface plasmon resonance (SPR) enhanced local field due to Ag particles and the existing mixed phase of TiO₂ is expected to provide a boost in its photoactivity in the visible region. In the present work the mixed phase Ag/TiO₂ photocatalyst showed large enhancement in the degradation of methylene blue compared to all the reference systems.     

Preparation and photocatalytic activity of TiO2-coated granular activated carbon composites by a molecular adsorption-deposition method

TiO₂ nanoparticle-coated granular activated carbon (GAC) composite photocatalysts (CPs) were successfully prepared by a molecular adsorption-deposition (MAD) method. The CPs were detected by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), BET surface area and UV-Vis adsorption spectroscopy, and their photoactivity was evaluated by methyl orange (MO) photodegradation. The results show that small-sized TiO₂ nanoparticles were dispersed well, deposited on the surface of GAC, and showed slight blue shift in comparison with pure TiO₂. With the increase in TiO₂ content, the CPs showed band gaps in lower energy, smaller surface areas and the higher content of Ti³⁺ ions. Compared with pure TiO₂ and others CPs samples, CPs-382 sample showed the highest photoactivity due to the optimum TiO₂ content and surface area besides the synergic effect of photocatalytic degradation of TiO₂ and adsorptive property of GAC. In addition, the CPs could be very easily reclaimed, recycled and reused for methyl orange removal while high photoactivity is preserved.     

Preparation and photocatalytic activity of TiO2-coated granular activated carbon composites by a molecular adsorption-deposition method

TiO₂ nanoparticle-coated granular activated carbon (GAC) composite photocatalysts (CPs) were successfully prepared by a molecular adsorption-deposition (MAD) method. The CPs were detected by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), BET surface area and UV-Vis adsorption spectroscopy, and their photoactivity was evaluated by methyl orange (MO) photodegradation. The results show that small-sized TiO₂ nanoparticles were dispersed well, deposited on the surface of GAC, and showed slight blue shift in comparison with pure TiO₂. With the increase in TiO₂ content, the CPs showed band gaps in lower energy, smaller surface areas and the higher content of Ti³⁺ ions. Compared with pure TiO₂ and others CPs samples, CPs-382 sample showed the highest photoactivity due to the optimum TiO₂ content and surface area besides the synergic effect of photocatalytic degradation of TiO₂ and adsorptive property of GAC. In addition, the CPs could be very easily reclaimed, recycled and reused for methyl orange removal while high photoactivity is preserved. Supported by the Natural Science Foundation of Hunan Province (Grant No. 06JJ50150), the Scientific Research Fund of Science and Technology Department of Hunan Province (Grant No. 2007GK3060) and Jishou University (Grant No. JSDXKYZZ200648)     

High ethanol sensitivity of Palladium/TiO2 nanobelt surface heterostructures dominated by enlarged surface area and nano-Schottky junctions

TiO₂ nanobelts were prepared by the hydrothermal growth method. The surface of the nanobelts was coarsened by selective acid corrosion and functionalized with Pd catalyst particles. Three nanobelt samples (TiO₂ nanobelts, surface-coarsened TiO₂ nanobelts and Pd nanoparticle/TiO₂ nanobelt surface heterostructures) were configured as gas sensors and their sensing ability was measured. Both the surface-coarsened nanobelts and the Pd nanoparticle-decorated TiO₂ nanobelts exhibited dramatically improved sensitivity to ethanol vapor. Pd nanoparticle-decorated TiO₂ nanobelts with surface heterostructures exhibited the best sensitivity, selectivity, working temperature, response/recovery time, and reproducibility. The excellent ethanol sensing performance is attributed to the large surface area and enhancement by Schottky barrier-type junctions between the Pd nanoparticles and TiO₂ nanobelts.     

原位红外光谱法研究La/TiO2对有机污染物的光催化降解

本工作采用改进的溶胶-凝胶法和浸渍法制备了TiO₂掺杂稀土离子La³⁺的La/TiO₂光催化剂，运用XRD、N₂吸附脱附、紫外可见漫反射光谱(DRS)、表面光电压谱(SPS)等手段进行表征，同时利用原位红外技术考察了La/TiO₂样品光催化降解乙烯、丙酮、苯的气-固相光催化氧化反应，对其光催化降解有机污染物的过程进行了研究。结果表明，TiO₂经适量La³⁺掺杂后，锐钛矿晶型的含量增加，晶粒度减小，比表面积增大，禁带宽度增加，表面光电压信号增强，光生电子-空穴对有效分离；La/TiO₂样品对乙烯、丙酮、苯的光催化性能与纯TiO₂相比均有不同程度的改善，乙烯可以被光催化氧化完全矿化生成CO₂，而丙酮被光催化氧化可能生成中间产物丙酸，苯被光催化氧化可能生成中间产物苯酚和苯醌。     

Photodegradation of Chlorinated Organic Wastes with n-TiO2 Promoted by P-CuO

A variety of chlorinated organic wastes were photodecomposed with p-CuO-modified TiO₂ particles (denoted CuO/TiO₂). Based on the photoactivity measured in oxygenated solutions containing sodium 2,2′-dichloropropionate, the photoactivity of TiO₂ is significantly enhanced with p-CuO loading; in the case with 0.4 wt% of CuO, the activity is increased by a facor of 4. Photochemical-TiO₂-slurry cell techniques and voltammetric characterizations suggest this CuO-promoted enhancement is likely to result from the acceleration of oxygen reduction at TiO₂ via Cu_IIO/Cu_I0. Long-term tests showed that these CuO/TiO₂ particles are photochemically robust; within 100-hours' continuous photolysis, insignificant loss in photoactivity was detected. However, increasing loading of p-CuO may jeopardize the photoactivity, due to the deterioration in the TiO₂ absorbability of UV irradiation.     

Formation of crystalline TiO2−xNx and its photocatalytic activity

Amorphous precursors to nitrogen-doped TiO₂ (NTP) and pure TiO₂ (ATP) powders were synthesized by hydrolytic synthesis and sol-gel method (SGM), respectively. Corresponding crystalline phases were obtained by thermally induced transformation of these amorphous powders. From FT-IR and XPS data, it was concluded that a complex containing titanium and ammonia was formed in the precipitate stage while calcination drove weakly adsorbed ammonium species off the surface, decomposed ammonia bound on surface of precipitated powder and led to substitution of nitrogen atom into the lattice of TiO₂ during the crystallization. The activation energies required for grain growth in amorphous TiO_2−xN_x and TiO₂ samples were determined to be 1.6 and 1.7 kJ/mol, respectively. Those required for the phase transformation from amorphous to crystalline TiO_2−xN_x and TiO₂ were determined to be 129 and 142 kJ/mol, respectively. A relatively low temperature was required for the phase transformation in NTP sample than in ATP sample. The fabricated N-doped TiO₂ photocatalyst absorbed the visible light showing two absorption edges; one in UV range due to titanium oxide as the main edge and the other due to nitrogen doping as a small shoulder. TiO_2−xN_x photocatalyst demonstrated its photoactivity for photocurrent generation and decomposition of 2-propanol (IPA) under visible light irradiation ().     

Low temperature CO oxidation on Au/TiO2 sol-gel catalysts

A comparative study on Au/TiO₂catalysts prepared by impregnation with HAuCl₄of commercial TiO₂ or by impregnation of sol-gel derived TiO₂has been carried out during CO oxidation. Specific surface areas and mean Au particle of 49 and 74 m²/g and 35 and 25 Å were obtained for impregnated commercial TiO₂ and sol-gel preparations, respectively. XRD patterns shown that in sol-gel derived TiO₂ only anatase phase was identified, while in commercial TiO₂ anatase and rutile phases co-exist. Titania support effect on Au activity for the oxidation of CO has been observed. The light-off during the reaction on Au/TiO₂initiates at 50°C, whereas for commercial impregnated TiO₂ catalyst the light-off initiates at 200°C.     

Morphology,structure, and photoactivity of two types of graphene oxide-TiO<Subscript>2</Subscript> composites

Two types of graphene oxide-TiO₂ composites were prepared: one by including graphene oxide flakes in the TiO₂ sol, followed by thermal treatment (GI composite) at 300°C, and the second by including graphene oxide flakes in the calcined (at 500°C) TiO₂ xerogel (GII composite). The composites were characterized by SEM, TEM-EDS, TEM-SADP, STEM-HAADF, HRTEM coupled with FT, XRD, and XPS. Photocatalysis results were fitted to different kinetic models (pseudo-first and pseudo-second kinetics, intraparticle Weber-Morris diffusion, film diffusion, and external mass transfer). The results showed that by introducing graphene oxide flakes in the TiO₂ sol, followed by thermal treatment at 300°C (GI composite), an efficient graphene oxide-TiO₂ catalyst with high specific surface area, heterogeneity, and many graphitized areas can be obtained. Complete crystallization of the composite is not the key issue for the best photoactivity achievement. The rate limiting step in the photocatalytic process is the photooxidation of SA molecules on the TiO₂ surface.