界面聚合法制备正二十烷微胶囊化相变储热材料

用界面聚合的方法,以甲苯-2,4-二异氰酸酯(TDI)和己二胺(HDA)为反应单体,非离子表面活性剂聚乙二醇壬基苯基醚(OP)为乳化剂,合成了正二十烷为相变材料的聚脲包覆微胶囊. 结果表明,二异氰酸酯和己二胺按质量比为1.5∶ 0.8进行反应. 空心微胶囊的直径约为0.2 μm,含正二十烷微胶囊直径为2~6 μm. 红外光谱分析证明, 囊壁聚脲是由TDI及HDA 2种单体形成. 正二十烷包裹效率为65%~80%. 微胶囊的熔点接近囊芯正二十烷的熔点,而其储热量在壁材固定时随囊芯的量而变. 热重分析结果表明,囊芯正二十烷、含正二十烷的微胶囊以及壁材聚脲,能够耐受的温度分别约为130、165及250 ℃.     

界面聚合法制备正二十烷微胶囊化相变储热材料

采用界面聚合的方法, 以甲苯鄄2,4-二异氰酸酯(TDI)和乙二胺(EDA)为反应单体, 非离子表面活性剂聚乙二醇壬基苯基醚(OP)为乳化剂, 合成了正二十烷为相变材料的聚脲包覆微胶囊. 结果表明, 二异氰酸酯和乙二胺按质量比1.9:1 进行反应. 以透射电镜和激光粒度分析仪分析微胶囊, 测得空心微胶囊直径约为0.2 μm, 含正二十烷微胶囊约为2-6 μm. 红外光谱分析证明, 壁材料聚脲是由TDI 及EDA 两种单体形成的. 正二十烷的包裹效率约为75%. 微胶囊的熔点接近囊芯二十烷的熔点, 而其储热量在壁材固定时随囊芯的量而变. 热重分析表明, 囊芯正二十烷、含正二十烷的微胶囊以及壁材料聚脲, 能够耐受的温度分别约为130 ℃、170 ℃及270 ℃.     

丙烯酸共聚物囊壁的正十八烷微胶囊的制备和性能表征

以二丙烯酸1,4-丁二醇酯为交联剂, 成功制备了甲基丙烯酸甲酯-甲基丙烯酸共聚物为壁材, 正十八烷为囊芯的相变材料微胶囊. 采用扫描电子显微镜(SEM)、差示扫描量热仪(DSC)和热重分析仪(TG)分别考察了单体与芯材投料比、单体浓度和交联剂的含量对微胶囊形貌、相变热性能、热稳定性能的影响. 实验结果表明: 随着单体与芯材投料比或单体浓度的增加, 微胶囊表面均变得致密, 壁厚增加; 随着交联剂含量的增加, 微胶囊的表面变得更加致密光滑, 热稳定性显著增强; 随着单体与芯材投料比的增大, 微胶囊热焓值减小, 被包裹的囊芯含量减少.     

具有薄荷香味的相变微胶囊的制备与表征

利用界面聚合法,以异佛尔酮二异氰酸酯与己二胺为单体聚合形成的聚脲为外壳,以正十八烷、薄荷素油的混合物为芯材,制备了具有薄荷香味的相变微胶囊。利用光学显微镜、扫描电镜、红外光谱仪、差示扫描量热仪、热重分析仪等对微胶囊的形貌、化学结构和热性能进行了表征。结果表明:制备的微胶囊为球形,平均粒径约7.0μm,有较高的储热能力和较好的热稳定性;芯材中添加8.3%的正十四醇或高熔点石蜡,可很好地抑制相变微胶囊的过冷现象。     

pH值对正十八烷微胶囊合成与性能的影响

pH值对正十八烷微胶囊合成与性能的影响;微胶囊;相变材料;正十八烷     

十八烷/聚(St-MMA)相变微胶囊制备及表征

采用乳液聚合的方法,分别选取聚苯乙烯(PS)、聚甲基丙烯酸甲酯(PMMA)或苯乙烯和甲基丙烯酸甲酯的共聚物为壁材,正十八烷为芯材,十二烷基苯磺酸钠(SDBS)为乳化剂,制作相变储能微胶囊。用粒径分析仪、透射电子显微镜(TEM)、热重分析仪(TG)和示差扫描量热测试仪(DSC)对微胶囊的形貌、相变热性能和热稳定性分别进行表征。结果表明:壁材选取两者共聚物,当两种单体的比例为St∶MMA=1∶5,SDBS用量为1.5g(总质量的3%)时,微胶囊粒径大小均匀,粒子分散性好,壁材的包裹性好。微胶囊的放热峰为起始温度为27.3℃,终止温度为31.9℃,相变温度为28.9℃,相变焓为48.4J/g。TG表明长期使用温度不能超过131℃。IR分析微胶囊中含有芯材和壁材。这种十八烷/聚(St-MMA)相变微胶囊可以用于诸能材料。     

石墨烯/正十八烷微胶囊的制备与及其热性能研究

以石墨烯/正十八烷为芯材,三聚氰胺-尿素-甲醛树脂(MUF)为壁材,苯乙烯马来酸酐共聚物(SMA)为乳化剂,采用乳液聚合法制备相变微胶囊.系统研究了石墨烯对于正十八烷微胶囊性能的影响.采用场发射扫描电子显微镜(FE-SEM)、傅里叶变换红外光谱分析仪(FTIR)、拉曼光谱仪、X射线衍射仪(XRD)、Hot Disk热常数分析仪、示差扫描量热仪(DSC)和热重分析仪(TGA)对相变微胶囊的外貌形态、晶型结构和热性能进行表征和分析.结果表明,微胶囊呈圆球形且光滑,粒径约为1~30μm.当石墨烯添加量为0.1 g时,微胶囊的形貌无明显变化.当加入过量石墨烯时,微胶囊出现了明显的团聚现象.XRD测试表明,包覆于微胶囊中的石墨烯没有使微胶囊的结晶峰位置发生明显的偏移,这对于微胶囊的实际应用是有利的.微胶囊的相变热焓和包覆率随着石墨烯的加入而不断减小,但芯材的过冷现象得到了明显的改善.石墨烯对于微胶囊传热性能的提升有着显著的效果.当石墨烯的添加量为0.2 g时,微胶囊的导热系数为0.092 W·m-1·K-1,与纯微胶囊相比提高了约51%,这说明石墨烯改善了传统相变微胶囊的传热性能,提升了相变微胶囊的应用性能.     

纳米二氧化硅改性石蜡微胶囊相变储能材料的研究

以石蜡为芯材,甲基丙烯酸甲酯-丙烯酸共聚物为壁材,纳米SiO2为改性剂,采用原位聚合法制备了石蜡微胶囊相变储能材料,系统研究了添加纳米SiO2对石蜡微胶囊相变材料性能的影响;采用傅里叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)、示差扫描量热法(DSC)和热重分析(TGA)等对石蜡微胶囊相变材料的化学结构、表面形貌和热性能进行了表征.研究表明,纳米SiO2能够有效提高微胶囊壁材的热稳定性,当丙烯酸酯壁材中添加3％改性纳米SiO2时,微胶囊呈球形且表面光滑,尺寸250 ～ 300 nm,具有良好的储热能力,相变潜热高达134.79 J/g,分解温度比未添加改性纳米SiO2的石蜡微胶囊提高了40 K,经过1000次热循环测试,石蜡渗漏率仅2.96％.     

细粒径石蜡微胶囊相变材料的制备与性能

采用阳离子和非离子复配乳化剂,通过原位聚合制备以丙烯酸酯为壁材,石蜡为芯材的细粒径微胶囊相变材料.采用傅里叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)、差示扫描量热(DSC)、热重(TG)及激光粒度仪分析表征了微胶囊相变材料的化学结构、表面形貌和热性能.结果表明,乳化剂的种类和壁材单体的配比对微胶囊性能有重要的影响.当采用阳离子和非离子复配乳化剂,壁材中单体甲基丙烯酸甲酯(MMA)与丙烯酸(AA)的质量比为9∶1时,微胶囊相变材料呈球形且表面光滑紧凑,尺寸仅为0.2~0.35μm,具有良好的储热能力,相变潜热高达169 J/g;微胶囊中壁材对石蜡芯材的分解具有明显热阻滞作用,分解温度比纯石蜡提高了150℃.     

以TDI和IPDI为单体合成聚氨酯微胶囊及其摩擦学性能

分别以甲苯-2,4-二异氰酸酯(TDI)和异佛尔酮二异氰酸酯(IPDI)为单体,通过原位聚合法制备了离子液体@聚脲(PU)微胶囊,并与环氧树脂共混制得环氧树脂复合材料.利用扫描电子显微镜分析了微胶囊及复合材料的表面形貌,通过电子万能试验机和摩擦磨损试验机探究了微胶囊改性复合材料在不同情况下的力学性能和摩擦学性能,用傅里叶变换红外光谱对微胶囊进行表征.分析结果表明,以IPDI为单体合成的微胶囊摩擦学性能更加优异,并且随着微胶囊用量的增加,复合材料的摩擦学性能有明显提高,当微胶囊添加质量分数为20%时,含有微胶囊的复合材料具有较低的滑动摩擦系数并且摩擦面较光滑,这是由于在实验过程中,随着微胶囊壁材的破损,芯材离子液体被释放,形成了一层致密的润滑膜.     

Polyurea nanocapsules obtained from nano‐emulsions prepared by the phase inversion temperature method

We describe here a new and simple method for preparation of polyurea nanocapsules from nanodroplets that were obtained by the phase inversion temperature (PIT) method. In the first stage, a nano‐emulsion was prepared, by a heating–cooling cycle, in which the oil phase contained an oil soluble monomer (toluene 2 , 4 ‐diisocyanate (TDI)). In the second stage, a water‐soluble monomer and crosslinker (diethylenetriamine (DETA)) was added, leading to formation of a polymeric shell by an interfacial polycondensation reaction. The new method was demonstrated for obtaining nanocapsules of about 100 nm, in which hexadecane, dodecane, or decane were the core materials, without using any special equipment. The morphology and structure of the nanocapsules were evaluated by attenuated total reflection Fourier transform infrared (ATR‐FTIR) measurements and electron microscopy. The thermal behavior of the nanocapsules containing hexadecane was studied by Differential Scanning Calorimetry (DSC) measurements, indicating that such nanocapsules can be utilized in thermal energy storage. Copyright © 2010 John Wiley & Sons, Ltd.     

Microencapsulation of n-Eicosane as Energy Storage Material

For heat energy storage application, polynrea microcapsules containing phase change material, n-eicosane, were synthesized by using interfacial polymerization method with toluene-2,4-diisocyanate (TDI) and diethylenetriamine(DETA) as monomers in an emulsion system. Poly(ethylene glycol)octyl-phenyl ether (OP), a nonionic surfactant,was the emulsifier for the system. The experimental result indicates that TDI was reacted with DETA in a mass ratio of 3 to 1. FF-IR spectra confirm the formation of wall material, polyurea, from the two monomers, TDI and DETA.Encapsulation efficiency of n-eicosane is about 75%. Microcapsule of n-eicosane melts at a temperature close to that of n-eicosane, while its stored heat energy varies with core material n-eicosane when wall material fixed.Thermo-gravimetric analysis shows that core material n-eicosane, micro-n-eicosane and wall material polyurea can withstand temperatures up to 130, 170 and 250℃, respectively.     

Microencapsulation of octadecane as a phase-change material by interfacial polymerization in an emulsion system

 Microcapsules containing phase-change material for thermal adaptable fiber application were synthesized and characterized. The microcapsules of about 1 μm in diameter were prepared using an interfacial polycondensation method with toluene-2,4-diisocyanate (TDI) and diethylenetriamine (DETA) as monomers in an emulsion system. Octadecane was used as a phase-change material and NP-10 which is nonionic surfactant, was used as an emulsifier. To investigate the reaction ratio of monomers, microcapsules were synthesized with 3 g TDI and 0–4 g DETA. Polyurea microcapsules were formed not only by reaction with TDI and DETA, but also by reaction of TDI with hydrolyzed TDI at the interface. TDI was reacted with DETA in the weight ratio of 3:1. NP-10 was reacted with TDI to form urethane. The microcapsules containing octadecane showed a phase change of octadecane at 29–30 °C. The core content measured using the heat of fusion of octadecane was less than that calculated. The efficiency of octadecane encapsulation increased as the core content decreased. Received: 17 July 2001 Accepted: 13 September 2001     

含苯并咪唑基团聚酰亚胺的合成与表征

使用一种含有苯并咪唑基团的二胺单体2-(3-氨基苯基)-5-氨基苯并咪唑与二酐单体进行缩聚反应, 得到一系列聚酰亚胺薄膜, 并对该类薄膜的热性能和机械性能进行表征.结果表明, 该类薄膜具有较高的耐热性和良好的机械性能.同时, 二胺单体中氨基的相对位置赋予分子链以较高的弯曲性, 使该类聚酰亚胺具有较好的热塑性和较高的热膨胀系数.     

A Study of the Slow Release of Urea from Microcapsules with TDI as the Wall-Sealing Treatment

The release of urea from ethylcellulose coated microcapsules was efficiently reduced by post-treatment with toluene-2,4-diisocyanate (TDI) in n-hexane. Our results show that TDI can be used as a sealant which modifies the shell characteristics of the ethylcellulose film. The modification is rather complicated in that it probably includes cross-linking between ethylcellulose and TDI, a reaction between urea and TDI, and biuret or polyurea formation from TDI absorbed on the microcapsules surface with moisture. The influence of post-treated conditions on the release of urea from ethylcellulose shell was studied.     

Preparation, Curing Reactivity and Thermal Properties of Titanium-doped Silicone Resins

Novel titanium-doped silicone resins were synthesized from low-cost silane monomers and tetrabutyl titanate as raw materials and hydrochloric acid as catalyst, with titanium element as dopant into principal chain of Si-O-Si. The resins were characterized by means of FTIR, 1 H NMR and 13 C NMR spectra, their thermal properties and curing properties were investigated and their corresponding films were determined. The results show that the thermal stability and storage stability of the resins were influenced by the types of silane monomers containing different carbon atomicities of organic group. The thermal stability of the titanium-doped silicone resin with a molar ratio of silane monomer B(n-propyl triethoxysilane) to silane monomer C(n-octyl triethoxysilane) being 1:1 is superior to that of the resin with a molar ratio of silane monomer B to silane monomer C being 1:3. However, the storage stability of the former is inferior to that of the latter.This work also showed that the synthesized titanium-doped silicone resins have the highest thermal stability up to 450―500 °C with an atomicity molar ratio of 1:4 of titanium to silicon in the reactants. But the best storage stability of the resin prepared from the reactants with an atomicity molar ratio of 1:6[n(Ti):n(Si)] was obtained. The effect of the type and content of curing agent on the curing properties of the resin was also studied. Moreover, thermal mechanism and curing mechanism were proposed in this work.     

Polypropylene fabrics padded with microencapsulated ammonium phosphate: Effect of the shell structure on the thermal stability and fire performance

Three types of microcapsules of di-ammonium hydrogen phosphate (DAHP) with different polymeric shells were evaluated as flame retardants in commercial polyurea padding for textiles. Encapsulated FR agent has the advantage of being compatible with the polymer matrix. The thermal degradation for the three types of DAHP microcapsules shows that our microcapsules act as intumescent fire retardants. The reaction to fire of polypropylene fabrics padded with FR polyurea loaded with neat DAHP or microencapsulated DAHP was studied with the cone calorimeter as a fire model.     

Influence of operation conditions on the microencapsulation of PCMs by means of suspension-like polymerization

Microcapsules containing PRS® paraffin wax (core) and a polystyrene shell were prepared by suspension-like polymerization. The influence of reaction temperature, stirring rate, and mass ratio of paraffin wax to styrene on the properties of phase change materials microcapsules was studied. The reaction temperature had not a significant effect on the size of the microcapsules but an increase of molecular weight and a narrow molecular weight distribution of polystyrene shell were observed when reaction temperature was increased. An exponential relationship between the stirring rate and the mean particle diameter in number has been found. It was observed that paraffin is difficultly encapsulated when the paraffin/polymer mass ratio was higher than 2.00, as a consequence of a shortage of polymer that could not completely cover the amount of paraffin added. However, when a large proportion of monomer was employed, the polymer tended to polymerize inside the droplets during the microencapsulation process forming complex inner structures. The microcapsules obtained have an interesting energy storage capacity of 153.5 J/g that makes them suitable for different applications.     

Synthesis and Characterization of Microcapsules with Chlorpyrifos Cores and Polyurea Walls

Microcapsules with chlorpyrifos cores and polyurea walls were synthesized with 2,4-tolylene diisocyanate as an oil-soluble monomer and ethylenediamine as a water-soluble monomer via an interracial polycondensation reaction. The products were characterized by means of Fourier transform infrared spectrometry, ^13C NMR spectrometry and ^31p NMR spectrometry. The morphology, the particle size and the particle size distribution, and the thermal properties were also evaluated. The prepared microcapsules exhibit clear and smooth surfaces and have a mean diameter of 28. 13 μm. These microcapsules also have a good thermal stability for long-term use, and have potential applications in minimizing the toxicity of chlorpyrifos through controlled release.