碱性电解液中K3[Fe(CN)6]在锌阳极上的自发还原和吸附延长锌镍电池的循环寿命

采用K₃[Fe(CN)₆]作为锌镍电池的电解液添加剂,克服了锌阳极的变形。此外,通过一系列实验设计和表征,探索了电解液中金属锌与K₃[Fe(CN)₆]的反应机理。通过XRD (X-ray diffraction)和XPS (X-ray photo-electron spectroscopy)测试,我们发现金属锌在KOH水溶液中能够与K₃[Fe(CN)₆]反应,将[Fe(CN)₆]^3–还原为[Fe(CN)₆]⁴⁻。添加K₃[Fe(CN)₆]的锌镍电池实现了更长的循环寿命,比不添加K₃[Fe(CN)₆]的锌镍电池长3倍以上。在相同循环次数下,改性电解质中锌阳极循环不仅形状变化较小,而且没有出现“死”锌现象,电极添加剂和粘结剂也没有发生偏析。此外,不同于一般的有机添加剂,K₃[Fe(CN)₆]的加入不仅不会增大电极的极化,还能够提高锌镍电池的放电容量和倍率性能。因此,考虑到这一改性策略有着较高的可行性和较低的成本,K₃[Fe(CN)₆]添加剂在锌镍电池的实际应用中具有极大的推广潜力。     

锂离子电池高镍正极材料掺铝的作用及掺铝方法的研究

为了探究铝对高镍层状氧化物在结构、形貌及性能方面的影响,本文采用两种不同的方式掺铝以制备NCA正极材料 （LiNi_0.8Co_0.15Al_0.05O₂）：一是固相法即将共沉淀合成的NC前驱体（Ni_0.84Co_0.16(OH)₂）在混锂烧结过程混入铝源（纳米Al₂O₃或Al(NO₃)₃）;二是共沉淀法即直接在合成前驱体过程中混入铝源（Al₂(SO₄)₃或NaAlO₂）即合成NCA前驱体（Ni_0.8Co_0.15Al_0.05(OH)_2.05）后再混锂烧结. 结果表明,掺铝能够降低阳离子混排程度、维持层状结构的稳定性,改善材料在充放电循环过程的放电电压及中值电压大幅下降的情况,提高其循环性能. 其中以NaAlO₂为铝源合成NCA前驱体所制备的NCA材料性能最优：在3.0 ~ 4.3 V充放电区间,0.1C倍率下首圈放电比容量达198 mAh·g^-1,首次库仑效率可达94.6%,1C倍率下循环200圈后容量保持率达70%.     

前驱体物相转变对浆态床合成甲醇催化剂活性的影响

采用并流共沉淀法, 通过考察老化温度, 研究CuO/ZnO/Al₂O₃催化剂前驱体晶相及组成的变化对浆态床催化合成甲醇的反应活性的影响. 结果表明, 前驱体的物相转变对浆态床合成甲醇活性影响显著, 单斜晶系锌孔雀石(Cu,Zn)₂CO₃(OH)2和斜方晶系绿铜锌矿(Cu,Zn)₅(CO₃)₂(OH)₆晶体是产生高活性催化剂的主要物相. 随着Cu²⁺/Zn²⁺进入Zn₅(CO₃)₂(OH)₆/Cu₂CO₃(OH)₂晶格, 离子同晶取代量增加, 催化剂前驱体中形成了固定铜锌比的锌孔雀石和绿铜锌矿物相. 焙烧后催化剂比表面积增大, CuO-ZnO固溶体协同作用加强, 浆态床催化合成甲醇的活性提高.     

超薄Ni(OH)2纳米片修饰Zn0.5Cd0.5S纳米颗粒作为二维/零维异质结构光催化剂可见光下光催化制氢

设计与制备高效的光解水催化剂是解决能源问题和环境问题的策略之一.硫化镉因其可在可见光引发下分解水制氢而受到广泛关注,然而光腐蚀严重,过电势高,载流子复合快速以及表面反应动力学缓慢等缺点极大地限制了其在光解水反应中的实际应用.本文采用简单液相法将均匀的Zn_0.5Cd_0.5S纳米颗粒锚定在超薄Ni(OH)₂纳米薄片上,构建紧密的二维/零维异质结构.通过调控Ni(OH)₂纳米片的含量,制备出不同Ni(OH)₂质量比(3%,5%,7%,9%,11%)的二维/零维Ni(OH)₂/Zn_0.5Cd_0.5S复合材料,并考察其可见光激发的光催化分解水制氢性能.在可见光照射下,Ni(OH)₂/Zn_0.5Cd_0.5S复合材料的光催化性能要大幅度地优于未修饰的Zn_0.5Cd_0.5S纳米颗粒,甚至远高于贵金属Pt修饰的Zn_0.5Cd_0.5S.在不同Ni(OH)₂含量的纳米复合材料中,7%Ni(OH)₂/Zn_0.5Cd_0.5S具有最高效的产氢性能,产氢速率可达6.87 mmol·h^–1·g^–1,且在波长为420 nm的表观量子产率为16.8%.在同等条件下,二维/零维7%Ni(OH)₂/Zn_0.5Cd_0.5S复合光催化剂的光催化分解水产氢速率分别约为纯Zn_0.5Cd_0.5S纳米颗粒和Pt/Zn_0.5Cd_0.5S光催化剂的43倍和8倍,甚至要高于零维/零维7%Ni(OH)₂/Zn_0.5Cd_0.5S纳米复合材料.7%Ni(OH)₂/Zn_0.5Cd_0.5S复合光催化剂具有优异的光催化产氢循环性能,通过循环反应后样品的X射线衍射,X射线光电子能谱和透射电子显微镜等表征,结果表明Ni(OH)₂/Zn_0.5Cd_0.5S在经过20 h的使用后,其晶体结构、表面化学成分和形貌结构未发生明显改变.通过研究样品的时间分辨荧光光谱,线性扫描伏安响应,光电流性能及电化学交流阻抗等,发现二维Ni(OH)₂纳米片的修饰能一定程度降低Zn_0.5Cd_0.5S的过电势,还能有效促进Zn_0.5Cd_0.5S的光生电子-空穴的分离和光生电子的转移.本文认为二维/零维Ni(OH)₂/Zn_0.5Cd_0.5S光催化活性的大幅提升主要由于Zn_0.5Cd_0.5S与Ni(OH)₂之间独特且牢固的纳米结构,在该过程中超薄Ni(OH)₂纳米片不仅能为Zn_0.5Cd_0.5S纳米颗粒的负载提供平台,而且作为一种高效的助催化剂,促进光生电子的转移以及为制氢反应提供更多的活性位点.本文可为多功能,高效及低成本的二维-零维异质结构光催化剂的制备及在太阳能转化方面的应用提供一定借鉴.     

丝光沸石水蒸气/酸浸渍脱铝的多核固体核磁共振研究

采用¹H,²⁹Si,²⁷Al魔角旋转固体核磁共振(MASNMR)及¹H-²⁹Si交叉极化(CP)技术研究丝光沸石水蒸气/酸浸渍脱铝过程中各种铝物质的结构与性质.结果表明,丝光沸石上骨架铝原子在水分子作用下,生成非骨架四配位铝物质[Al(OH)₃(H₂O)],分别在²⁷Al谱δ45和¹H谱δ3.0处出现共振信号,这种铝物质不同于扭曲四配位铝,在高温下进一步水合生成Al(OH)₃(H₂O)₂和Al(OH)₃(H₂O)₃,即非骨架五配位和六配位铝物质.¹H-²⁹SiCP和¹H谱证实,水蒸气脱铝使丝光沸石产生了大量的硅羟基和铝羟基.     

PVC/插层稀土类水滑石的热稳定性能研究

以山梨酸、La(NO_3)_3,Al(NO_3)_3,Mg(NO_3)_2和Na OH为主要原料合成了山梨酸插层镁铝镧类水滑石(Mg Al La-SA LDHs),通过X射线衍射(XRD)、红外光谱(FT-IR)进行结构表征。采用刚果红法、热老化烘箱法、转矩流变法、电导率法等研究了山梨酸插层类水滑石及与季戊四醇、硬脂酸锌复合后添加到聚氯乙烯(PVC)的热稳定性能。结果表明:山梨酸插层类水滑石可有效地延长PVC热稳定时间,抑制初期着色,降低加工能耗,热降解活化能较纯PVC提高了6.59 k J·mol~(-1)。按质量份数1/4/1与季戊四醇、硬脂酸锌复合后,热降解活化能较复合前提高了13.96 k J·mol~(-1),热稳定效果更优。     

12-磷钨杂多酸根柱撑水滑石合成及催化脂肪酸甲酯环氧化

研究了一种可用于脂肪酸甲酯环氧化的类水滑石催化剂. 采用共沉淀法合成类水滑石[Mg_1-xAl_x(OH)₂]^x+-(NO^3-)_x·mH₂O, 通过离子交换法制备出一种新的柱撑水滑石[Mg_1-x²⁺Al_x³⁺(OH)₂]^x+[PW₁₂O₄₀]_x/3^3- ·mH₂O化合物, 并由XRD,FT-IR, Raman, ICP和UV-Vis 进行了表征. 用制备的类水滑石应用于无羧酸环境下的催化脂肪酸甲酯环氧化反应, 结果表明, 柱撑水滑石较插层前转化率和选择性都有了明显的提高. 考察了反应温度、反应时间、催化剂重复使用等因素对环氧化反应的影响, 在60 ℃时反应16 h, 转化率和选择性分别达到56.1%和59.4%, 催化剂使用4 次后重复使用率仍高于90%. 对催化剂催化环氧化的机理进行了初步的探讨.     

阻燃超疏水棉纤维的制备及性能

将氢氧化镁(Mg(OH)₂)凝胶沉积到棉纤维上,以提高棉纤维表面粗糙度和阻燃性能,随后将含有Mg(OH)₂的棉纤维浸渍到聚二甲基硅氧烷(PDMS)溶液,获得阻燃超疏水棉织物。 并对棉纤维进行了傅里叶变换红外光谱仪(FTIR)、扫描电子显微镜(SEM)、疏水性、热稳定性、阻燃性能和耐久性测试。 结果表明,Mg(OH)₂负载到织物上,使得织物表面具有一定的微/纳米结构,形成了粗糙涂层。 当Mg(OH)₂浓度为1.0 mol/L时,Mg(OH)₂/PDMS改性的织物接触角(CA)可达158°,极限氧指数(LOI)提升至24.5%,导热系数为0.0525 W/(m·K), 具有超疏水和阻燃性能。 整理后织物经过20次洗涤,100次磨擦,极端条件处理后,CA仍大于150°,LOI值高于23%,显示了较好的耐久性。     

不同金属化合物催化呼和浩特煤加氢气化实验研究

在加压固定床反应器上考察了K₂CO₃、Na₂CO₃、Ca(OH)₂、Ni(NO₃)₂催化剂对呼和浩特煤加氢气化反应的催化效果,并考察了温度对催化剂效果的影响。实验结果表明,不同种类的金属化合物对气化反应的催化效果有明显影响,催化活性依次为K> Na> Ni> Ca。与原煤气化相比,在相同时间内达到相同碳转化率时,碱金属化合物K₂CO₃的加入使原煤加氢气化的气化温度降低150℃以上,碱金属化合物Na₂CO₃降低约150℃,过渡金属化合物Ni(NO₃)₂降低50℃以上,碱土金属化合物Ca(OH)₂的加入会吸收一部分CO₂产品,表观上反而降低了碳转化率。SEM及BET表征结果表明,煤样负载不同金属化合物催化剂后表面形态及孔结构有一定差异。     

Zn-La合金制备及其电化学性能研究

采用固相扩散法合成Zn＿La合金,并研究La对锌电极化学性能的影响.实验表明:La的适量添加能抑制锌电极的枝晶及腐蚀等问题,从而明显改善锌电极的循环性能,其中以0.5at.%La的添加量为最佳.在100mA/g电流密度下,循环80周期后,其放电容量仍达520mAh/g,XPS测试表明,La主要以La2O3/La(OH)3的形式附着在锌电极表面上.正是由于La2O3/La(OH)3的存在,显著改善了锌电极的循环充放电寿命.     

锌铝层状双金属氢氧化物焙烧物对钢筋的缓蚀作用研究

在空气气氛下合成了锌铝层状双金属氢氧化物(Zn-Al LDHs)和焙烧物(Zn-Al CLDHs),扫描电镜结果表明,所制得的双金属氢氧化物具有明显的层状结构. 文中研究了Zn-Al CLDHs 对钢筋的腐蚀保护效果,Zn-Al CLDHs固体在NaCl 溶液中浸泡处理3 h 后,钢筋的腐蚀速率显著降低. 实验证明,Zn-Al CLDHs 在结构重组过程中可吸收溶液中的Cl^-,同时释放出OH^-,改善腐蚀环境,有效抑制钢筋的腐蚀.     

A magnetic organic-inorganic composite: Synthesis and characterization of magnetic 5-aminosalicylic acid intercalated layered double hydroxides

A core-shell structured magnetic layered organic-inorganic material involving 5-aminosalicylic acid (5-ASA) intercalated Zn-Al layered double hydroxides (LDHs) and magnesium ferrite (MgFe₂O₄) is assembled by a coprecipitation method. The powder X-ray diffraction results show the coexistence of the clear but weak diffractions of MgFe₂O₄ and ordered relatively stronger reflections of 5-ASA intercalated LDHs. The TEM image of magnetic 5-ASA intercalated LDHs reveals that the LDHs layer covers the MgFe₂O₄ particles or their aggregates with particle size of 50-80 nm. The vibration sample magnetization (VSM) measurements exhibit the increase in saturation magnetization of magnetic 5-ASA intercalated LDHs samples with increasing amount of magnetic core. The XPS analyses account for a majority of Zn, Al and O atoms on the surface of magnetic particles. It is suggested that the magnetic core MgFe₂O₄ was coated with LDHs layer probably through Zn-O-Mg and Al-O-Mg linkages, and a core-shell structured model is tentatively proposed.     

氧化锌表面包覆Sn_6O_4(OH)_4的制备及其在锌镍电池中的应用

采用水热-共沉淀法在氧化锌表面包覆锡化合物,利用扫描电子显微镜(SEM)、X射线衍射(XRD)和能谱分析(EDS)对制备的包覆ZnO材料进行表征。结果表明:XRD表明附着在氧化锌表面的是Sn_6O_4(OH)_4,且结晶度较好;SEM测试显示在p H=12条件下,Sn_6O_4(OH)_4能够很好地附着在氧化锌颗粒表面;EDS显示组成物中的元素包含Zn、Sn、O三种元素。利用循环伏安曲线(CV)、电化学阻抗谱(EIS)、倍率充放电技术对包覆ZnO材料进行了电化学性能的测试,结果表明:包覆Sn_6O_4(OH)_4的ZnO可以提高锌负极的耐蚀性能,增大电荷转移电阻(Rct);锌电极覆Sn_6O_4(OH)_4量为3%时充放电效率最佳,在0.2C充放循环40次后充放电循环保持率仍有70%。     

氧化锌表面包覆Sn6O4(OH)4的制备及其在锌镍电池中的应用

采用水热-共沉淀法在氧化锌表面包覆锡化合物,利用扫描电子显微镜（SEM）、X射线衍射（XRD）和能谱分析对制备的包覆ZnO材料进行表征。结果表明：XRD表明附着在氧化锌表面的是Sn₆O₄（OH）₄,且结晶度较好;SEM测试显示在pH=12条件下,Sn₆O₄（OH）₄能够很好地附着在氧化锌颗粒表面;能谱分析显示组成物中的元素包含Zn、Sn、O三种元素。利用循环伏安曲线、电化学阻抗谱（EIS）、倍率充放电技术对包覆ZnO材料进行了电化学性能的测试,结果表明：包覆Sn₆O₄（OH）₄的ZnO可以提高锌负极的耐蚀性能,增大电荷转移电阻（R_ct）;锌电极覆Sn₆O₄（OH）₄量为3%时充放电效率最佳,在0.2C充放循环40次后充放电循环保持率仍有70%。     

La(OH)3和 La2O2CO3纳 米 棒 的 合 成 及 其 催 化 Claisen-Schmidt缩合反应性能简

通过调节溶液的pH值,在水热条件下合成出长径比为2-45的La（OH）₃纳米棒. 对水热合成过程中间体的结构演变分析,发现高碱度有利于小尺寸晶核的形成,La（OH）₃晶体结构的各向异性导致这些晶种沿着C轴方向生长,进而形成纳米棒结构. 将La（OH）₃纳米棒前驱体于773 K焙烧可以得到长径比为2-20的La₂O₂CO₃纳米棒. 随着长径比的增加,La₂O₂CO₃纳米棒暴露的（110）晶面逐渐增加,La³⁺-O^2-碱性位的数目也从0.08增加到0.24 mmol/g. 因此,在Claisen-Schmidt缩合反应中,La₂O₂CO₃纳米棒催化剂上的反应速率随着长径比的增加而逐渐增大.     

Investigation of Structural and Luminescent Properties of Sol-Gel-Derived Cr‑Substituted Mg3Al1−xCrx Layered Double Hydroxides

In the present work, Cr-substituted Mg₃Al_1−xCr_x layered double hydroxides (LDHs) were synthesised through the phase conversion of sol-gel-derived mixed-metal oxides in an aqueous medium. The chromium substitution level in the range of 1 to 25 mol% was investigated. It was demonstrated that all synthesised specimens were single-phase LDHs. The results of elemental analysis confirmed that the suggested synthetic sol-gel chemistry approach is suitable for the preparation of LDHs with a highly controllable chemical composition. The surface microstructure of sol-gel-derived Mg₃Al_1−xCr_x LDHs does not depend on the chromium substitution level. The formation of plate-like agglomerated particles, which consist of hexagonally shaped nanocrystallites varying in size from approximately 200 to 300 nm, was observed. Optical properties of the synthesised Mg₃Al_1−xCr_x LDHs were investigated by means of photoluminescence. All Cr-containing powders exhibited characteristic emission in the red region of the visible spectrum. The strongest emission was observed for the sample doped with 5 mol% Cr³⁺ ions. However, the emission intensity of samples doped with 1–10 mol% Cr³⁺ ions was relatively similar. A further increase in the Cr³⁺ ion concentration to 25 mol% resulted in severe concentration quenching.     

负载PtSn金属助剂的镁铝水滑石上的丙烷脱氢反应研究

我们研究了以镁铝水滑石作为载体,利用水滑石层间阴离子的可交换性,负载活性金属铂和锡的丙烷脱氢反应.在镁铝水滑石载体中加入Ga能够影响丙烷脱氢活性,当镓的含量为1%时催化剂丙烷脱氢反应活性最高,反应初始时,丙烷转化率为46.5%,反应2 h后,丙烷转化率仍有37.5%.当以Mg(Ga)(Al)O-1%为载体时,考察了不同H_2/C_3H_8摩尔比对丙烷脱氢活性的影响,结果表明当H_2/C_3H_8摩尔比为0.5∶1时,丙烷脱氢反应具有最佳的反应活性,即当在原料气中加入H_2时,能够使得丙烷脱氢的转化率大幅度提升,且选择性也有所提升.烷烃脱氢是一个吸热反应,同时考察了温度对烷烃脱氢反应性能影响,结果表明温度越高,丙烷脱氢反应具有更高的转化率.对催化剂进行长时间寿命实验考察,发现当反应经过40 h后,丙烷的转化率仍有23.5%,说明Pt Sn-Mg(Ga)(Al)O-1%催化剂具有较好的稳定性.     

Activation-induced layered structure in NiCoAl by atomic modulation for energy storage application

The surface activation of alloys favors their electrochemical interactions, ion diffusivity, and the rapid kinetics of ions and electrons, leading to the formation of self-supported layered double hydroxides (LDHs) in them. However, the formation of LDHs at different depths in the alloy upon activation, their electronic/atomic structures, and their electrochemical charge storage mechanism, have not been thoroughly explored. Herein, Ni ion-substituted CoAl alloys are prepared by arc melting and activated by KOH electrolyte, which is responsible for the modulation of the atomic configuration as confirmed by XRD. Raman depth mapping demonstrates how the LDHs vary with depth upon activation and that the octahedral and tetrahedral symmetry sites of CoO and Co₃O₄ are responsible for the formation of the layered structures of CoOOH and Co(OH)₂, respectively. The activated Ni₁₀Co₈₅Al₅ has a superior volumetric capacitance of 4.15 F/cm³ at 0.5 mA/g, which is 38.6 times that of an unactivated one, and excellent cyclic stability up to 5000 cycles, and a voltage of 0.54 V generated from a fabricated supercapacitor cell. X-ray Absorption Spectroscopy (XAS) analysis indicates greater charge transfer by Co than by Ni and the modulation of the local atomic structures facilitates electrochemical charge storage in Ni₁₀Co₈₅Al₅. This work presents an easy route for the development of advanced LDHs, and the mechanism of electrochemical charge storage in them.     

Nanocrystalline nickel cobalt hydroxides/ultrastable Y zeolite composite for electrochemical capacitors

A novel nanocomposite of Co(OH)₂−Ni(OH)₂ and ultrastable Y molecular sieves was synthesized by an improved chemical precipitation method for electrochemical capacitors. The Co(OH)₂−Ni(OH)₂/ultrastable Y zeolite (USY) composite and its microstructure were characterized by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. Electrochemical characterization was performed by cyclic voltammetry and galvanostatic charge–discharge measurements. The results show that Co(OH)₂−Ni(OH)₂/USY microstructure applied for the electrochemical energy storage has displayed superior capacitive performance. The effect of heat treatment conditions on specific capacitance properties was also systemically explored. Upon annealing at 250 °C, the maximum specific capacitance was up to 479 F/g (or 1,710 F/g after correcting for the weight percent of Co(OH)₂−Ni(OH)₂ phase). Annealing temperatures higher than 250 °C may cause the hydroxide to form oxide phase and decrease the surface activity of the oxide, thereby leading to a decline of the specific capacitance.     

Effect of La2O3 on Catalytic Performance of Au/TiO2 for CO Oxidation

Pure TiO₂ and La-doped TiO₂ were prepared by the sol-gel method. Au was supported on TiO₂ by the deposition-precipitation (DP) method, and its catalytic activity for CO oxidation was tested. The results showed that doping La in Au/TiO₂ could improve its catalytic activity obviously for CO oxidation. The analyses of X-ray diffraction (XRD), temperature-programmed desorption (TPD), and Brunauer-Emmett-Teller (BET) surface area further showed that the presence of La in TiO₂ not only increased its surface area and restrained the growth of TiO₂ crystallites, but could also enhance the microstrain of TiO₂. In terms of O₂-TPD, a new adsorbed species O⁻ appeared on the surface of La-doped TiO₂. The results of in-situ Fourier transform-infrared (FT-IR) spectroscopy illustrated that the high activity of Au/La₂O₃-TiO₂ was attributed to the presence of La promoting the reactivity of CO adsorbed on the Au site and the formation of the second active site on the surface of TiO₂