铕掺杂TiO2的制备及其可见光光催化性能研究

采用溶胶-凝胶法制备了不同铕(Eu)掺杂量的TiO₂纳米颗粒(Eu-TiO₂),利用透射电镜(TEM),X射线光电子能谱(XPS),X射线衍射(XRD)及紫外可见漫反射(UV-Vis DRS)等方法对Eu-TiO₂进行了物理特性的初步表征.结果表明:与未掺杂纳米TiO₂比较,Eu-TiO₂禁带宽度变窄,具有可见光光催化活性.在可见光下(λ≥420 nm)照射下,以光催化降解染料罗丹明B(Rhodamine B,RhB)为目标反应,探讨了Eu-TiO₂不同制备条件对RhB降解光催化活性的影响,优化得到制备高活性Eu-TiO₂最佳pH为3、掺杂比例(n_Eu/n_Ti)为0.05%、煅烧温度为500 ℃.研究了可见光照射下Eu-TiO₂降解RhB和无色有机小分子水杨酸(SA)光催化反应条件及降解特性,RhB的12 h深度氧化矿化率为60.2%,SA的8 h降解率达到100%.通过跟踪测定可见光下Eu-TiO₂光催化反应过程中氧化物种的变化,研究了可见光激发Eu-TiO₂光催化反应机理,表明其光催化反应主要涉及羟基自由基(·OH)历程.     

Bi/BiVO4&Bi4V2O11复合催化剂的制备及其光催化性能

经由溶剂热反应、光辅助还原过程制备Bi/Bi VO_4Bi_4V_2O_(11)纳米复合光催化材料。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、高分辨率透射电子显微镜(HRTEM)、X射线光电子能谱(XPS)、紫外-可见漫反射光谱(UV-Vis DRS)、N_2吸附-脱附等温线和光致发光(PL)等手段对该复合物进行表征。实验结果表明当金属Bi与BiVO_4Bi_4V_2O_(11)的质量比值为0.8,可见光照射30 min时,Bi/BiVO_4Bi_4V_2O_(11)复合催化剂对罗丹明B(RhB)的降解率可达95.6%。此外,Bi/BiVO_4Bi_4V_2O_(11)对四环素(TC)的降解也表现出增强的光催化性能。Bi/BiVO_4Bi_4V_2O_(11)复合材料提升的光催化性能可能归因于金属Bi的表面等离子体共振(SPR)效应、拓宽的可见光吸收范围和增大的比表面积。此外,提出了复合光催化剂可能的光催化机理。     

施主掺杂对BaTiO3钙钛矿半导体纳米晶光催化性能的影响

以沉淀法制备的Cu_2O为牺牲模板剂,采用水热法制备La施主掺杂的BaTiO_3钙钛矿半导体纳米晶,借助X射线衍射(XRD)、透射电子显微镜(TEM)、高分辨透射电镜(HRTEM)、X射线光电子能谱((XPS)、扫描电子显微镜(SEM)、紫外-可见漫反射光谱(UV-Vis DRS)表征La掺杂的BaTiO_3晶的物相、微观形貌及光催化性能。结果表明,La掺杂BaTiO_3构建了晶体缺陷,有效提高了BaTiO_3的光催化性能。当掺杂量为4%(w/w)时,样品的光催化性能最好,在可见光照射360 min后,对4-硝基苯酚溶液的降解率可达到93.2%。该催化剂5次循环后的活性仍然大于86.7%,表明La施主掺杂的BaTiO_3是一种有效的可见光催化剂。     

中空花状可见光响应催化剂g-C_3N_4@BiOCl的制备及其光催化活性

以g-C_3N_4/H_2SO_4溶液和硝酸铋为前驱体,采用自组装法制备了中空花状且具有可见光响应能力的异质结光催化剂gC_3N_4@BiOCl。利用X射线衍射、电子扫描显微镜、高分辨透射电镜、X射线能谱、紫外可见漫反射光谱及X射线光电子能谱等表征手段确证了催化剂的结构。该催化剂能够有效地实现光生电子-空穴的分离,表现出优异的可见光催化活性。通过对50 mg·L~(-1)罗丹明B的降解实验验证了g-C_3N_4@BiOCl的光催化活性,在可见光条件下(λ≥420 nm)的降解效率优良,12 min即可达到99%。     

一步醇-水热法合成高效的F掺杂BiVO_4光催化剂（英文）

以NH_4F为掺杂前体,采用简单的一步醇-水热法制备了F掺杂BiVO_4光催化剂。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)、紫外-可见漫反射光谱(UV-Vis)和光致发光光谱(PL)表征了这些光催化剂的物理化学性质。在少量H_2O_2存在条件下,以可见光照射下光催化降解苯酚的反应测定了这些光催化剂的催化活性。研究表明,相较于未掺杂的BiVO_4样品而言,F掺杂BiVO_4样品不仅仍保留了单斜结构,而且有更高的结晶度、表面氧空位密度和光生电荷载流子分离效率,更强的光吸收和更低的带隙能。在这些F掺杂BiVO_4样品中,以nF/nBi的理论值为1.0且带隙能为2.43 eV的F掺杂BiVO_4样品的光催化活性最好(90 min内苯酚的降解率可达95%)。这一优良的光催化性能与其具有最高的结晶度、表面氧空位密度和光生电荷载流子分离效率,最强的光吸收和最低的带隙能有关。     

Ag_2CO_3/BiVO_4复合微米片光催化剂的制备、表征及光催化机理

采用水热法制备粒径为1~2μm的BiVO_4微米片,然后在微米片表面沉积不同含量的Ag_2CO_3颗粒,制备Ag_2CO_3/BiVO_4复合微米片光催化剂。利用X射线粉末衍射(XRD)、扫描电镜(SEM)、红外光谱(FTIR)、紫外-可见漫反射光谱(UV-Vis DRS)、光致发光(PL)光谱、瞬态光电流-时间响应对催化剂进行表征。以可见光为光源,罗丹明B为降解对象进行光催化活性测试。结果表明,复合适量Ag_2CO_3有利于提高光催化剂的比表面积,改善催化剂的表面性能。活性测试结果表明,当复合10%(w/w)Ag_2CO_3时,Ag_2CO_3/BiVO_4光催化活性最佳,比纯BiVO_4提高4.4倍。光致发光(PL)光谱、瞬态光电流-时间响应测试结果表明,复合Ag_2CO_3能有效抑制光生电子与空穴的复合。自由基捕获实验结果表明,该体系的活性氧物质为空穴和羟基自由基。Ag_2CO_3/BiVO_4复合光催化剂活性提高的原因,是较宽带隙的Ag_2CO_3与较窄带隙的BiVO_4形成的异质结有效抑制了光生电子与空穴的复合,同时两者适宜的能带结构保证产生更多的空穴,从而具有更强的氧化能力。     

添加NaBF_4对阳极氧化法制备TiO_2纳米管光催化剂的影响

在阳极氧化电解液中添加Na BF4制得了具可见光活性的B掺杂TiO_2纳米管阵列(B/TNTs)。采用扫描电镜(FE-SEM)、能谱仪(EDS)、X射线衍射(XRD)、傅立叶红外光谱(FTIR)、紫外-可见漫反射光谱(UV-Vis DRS)以及X射线光电子能谱(XPS)对样品进行表征,以亚甲基蓝(MB)的光催化降解为目标反应评价其光催化活性。结果表明:添加Na BF4后,TiO_2纳米管表面形貌变化较大;B掺入到TiO_2晶格中形成B-O-Ti键;B掺杂使得TiO_2纳米管表面羟基量增加、光学带隙能减小、光吸收阀值红移,且B掺杂量越多,其相应值的变化量越大;B掺杂能促进TiO_2锐钛矿相的发育,纳米管经550℃煅烧后仍保持未掺杂样品的锐钛矿相结构;Na BF4的最佳添加量为0.6%(w/w)时,所得样品光催化活性最佳,可见光下光催化降解MB的4 h降解率由未添加的39.90%提高至75.15%,且反复使用10次后其光催化性能基本保持不变;总有机碳(TOC)分析结果表明,MB在可见光下能被B/TiO_2有效矿化。     

一锅法制备Co3O4/g-C3N4复合光催化剂及其光催化性能

以三聚氰胺和六水合氯化钴为原料,一锅法制备Co_3O_4负载的多孔石墨相氮化碳(Co_3O_4/g-C_3N_4)复合光催化材料。采用X射线衍射(XRD)、傅里叶变换红外(FT-IR)光谱、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)、光致发光光谱(PL)等手段对其结构和光学特性进行表征。以盐酸四环素(TC)为目标污染物,评价了不同负载量Co_3O_4/g-C_3N_4复合光催化剂的可见光催化性能。结果表明,所制备的Co_3O_4/g-C_3N_4复合光催化剂为多孔结构,其比表面积较大,并在可见光区域具有显著的吸收。利用原位生成的Co_3O_4纳米粒子在氮化碳表面形成异质结构,可有效转移光生载流子,降低光生电子-空穴的再结合率,从而提高光催化活性。并且存在最佳Co_3O_4复合量,当六水合氯化钴加入量为三聚氰胺的8%(w/w)时,所制备的复合光催化剂CoCN-8具有最佳的光催化性能。在可见光的照射下,60 min内可降解85%的TC,而同样条件下,纯g-C_3N_4仅降解23%的TC。     

Ag3PO4/Ag2S/g-C3N4复合光催化剂的制备与性能

通过沉积法和离子交换法成功地制备了Ag_3PO_4/Ag_2S/g-C_3N_4复合型光催化剂。利用X射线多晶粉末衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、N_2吸附-脱附等温线、紫外-可见漫反射光谱、荧光光谱等手段对样品进行了表征。通过降解罗丹明B考察其可见光催化活性及稳定性,研究了硫化钠与磷酸银物质的量的比值(n_(Na_2S)/n_(Ag_3PO_4))、g-C_3N_4添加量对所制备复合光催化材料性能的影响,同时对光催化机理进行了探讨。结果表明,随着n_(Na2S)/n_(Ag3PO4)的增加,所得复合催化材料活性先增加后降低;当n_(Na2S)/n_(Ag_3PO_4)为1.5%、g-C_3N_4与Ag_3PO_4的质量比为3∶7时制备的催化剂ASC1.5的光催化活性最好,在可见光照射下,40 min内可将罗丹明B完全降解,且5次循环使用后仍保持较高的催化活性。和Ag_3PO_4相比,Ag_3PO_4/Ag_2S/g-C_3N_4复合型光催化材料的活性与稳定性都得到明显提高,这主要归因于复合催化剂比表面积和孔结构的增加,载流子分离效率的提高。光催化机理研究表明,空穴(h~+)、超氧阴离子自由基(·O~(2-))和羟基自由基(·OH)都是光催化过程中的主要活性物种。三者作用大小依次为:h~+·O~(2-)·OH。     

Hg掺杂CdS的制备及可见光降解有毒有机污染物

采用镉硫共沉淀方法制备了Hg掺杂CdS(Hg_xCd_1-xS)光催化剂,运用X射线衍射法(XRD)、X射线光电子能谱(XPS)、透射电镜(TEM)和紫外-可见吸收光谱对所制备的催化剂进行了表征;利用可见光催化降解罗丹明B(Rhodi-amine B,RhB)和2,4-二氯苯酚(2,4-dichlorophenol,2,4-DCP)为探针反应,对Hg_xCd_1-xS可见光催化活性进行了研究,通过跟踪RhB降解过程中吸收光谱的变化和总有机碳(TOC),评价了Hg_xCd_1-xS对有机物的氧化降解及深度矿化能力.结果表明:Hg_xCd_1-xS催化剂为立方晶型,Hg的最佳掺杂量为5%,其禁带宽度约为2.15 eV,对RhB和2,4-DCP均有较好的降解效果,实验条件下30 min RhB褪色率为100%,RhB的30 h矿化率为45.5%,2,4-DCP的16 h降解率达55%.Hg_xCd_1-xS可见光光催化降解RhB具有较高的稳定性,Hg的掺杂能有效降低CdS光腐蚀问题.通过ESR跟踪测定光催化反应过程中产生的自由基,表明降解过程涉及·OH机理.     

Li_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3,Na_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3的离子交换研究

研究了在不同温度下的NaNO3和AgNO3水溶液中Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3离子交换行为.实验表明Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3均显示出了高选择性与Na+和Ag+进行离子交换的特征,且对Ag+的选择性高于Na+.升高温度可显著提高Ag/Li和Ag/Na的交换反应速度.     

Crystal growth, structure determination, and optical properties of new potassium-rare-earth silicates K3RESi2O7 (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu)

Single crystals of K₃RESi₂O₇ (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu) were grown from a potassium fluoride flux. Two different structure types were found for this series. Silicates containing the larger rare earths, RE=Gd, Tb, Dy, Ho, Er, Tm, Yb crystallize in a structure K₃RESi₂O₇ that contains the rare-earth cation in both a slightly distorted octahedral and an ideal trigonal prismatic coordination environment, while in K₃LuSi₂O₇, containing the smallest of the rare earths, lutetium is found solely in an octahedral coordination environment. The structure of K₃LuSi₂O₇ crystallizes in space group P6₃/mmc with a=5.71160(10) Å and c=13.8883(6) Å. The structures containing the remaining rare earths crystallize in the space group P6₃/mcm with the lattice parameters of a=9.9359(2) Å, c=14.4295(4) Å, (K₃GdSi₂O₇); a=9.88730(10) Å, c=14.3856(3) Å, (K₃TbSi₂O₇); a=9.8673(2) Å, c=14.3572(4) Å, (K₃DySi₂O₇); a=9.8408(3) Å, c=14.3206(6) Å, (K₃HoSi₂O₇); a=9.82120(10) Å, c=14.2986(2) Å, (K₃ErSi₂O₇); a=9.80200(10) Å, c=14.2863(4) Å, (K₃TmSi₂O₇); a=9.78190(10) Å, c=14.2401(3) Å, (K₃YbSi₂O₇). The optical properties of the silicates were investigated and K₃TbSi₂O₇ was found to fluoresce in the visible.     

Near infrared study of aqueous rare-earth ethylsulfates

The near infrared spectra of aqueous solutions of the ethylsulfates of La, Nd, Gd, Tb, Er, Yb, Lu, Y, and Na have been determined from about 0.2 mol-dm^–3 to nearly saturation. The extinction coefficients of water have been calculated taking into account the absorption of ethylslfate anions determined in separate experiments. Their values appeared to be nearly the same as that of pure water. The relative contents of free OH groups in 0.5 and 0.7M solutions have been estimated from the absorbances at 1160 nm. They were lower in solutions of the heavy rare-earth ethylsulfates (Tb, Er, Yb, Lu) than in equimolar solutions of the lighter ones (La, Nd), confirming our previous view that secondary hydration of the heavy trivalent rare-earth cations is distinctly stronger than that of the lighter ones. A comparison of the spectra of these aqueous ethylsulfates with those of perchlorates shows that the structure-breaking ability of the C₂H₅SO ₄ ^– ion is much smaller than that of perchlorate anion.     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

Structural studies of five layer Aurivillius oxides: A2Bi4Ti5O18 (A=Ca, Sr, Ba and Pb)

The room temperature structures of the five layer Aurivillius phases A₂Bi₄Ti₅O₁₈ (A=Ca, Sr, Ba and Pb) have been refined from powder neutron diffraction data using the Rietveld method. The structures consist of [Bi₂O₂]²⁺ layers interleaved with perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks. The structures were refined in the orthorhombic space group B2eb (SG. No. 41), Z=4, and the unit cell parameters of the oxides are a=5.4251(2), b=5.4034(1), c=48.486(1); a=5.4650(2), b=5.4625(3), c=48.852(1); a=5.4988(3), b=5.4980(4), c=50.352(1); a=5.4701(2), b=5.4577(2), c=49.643(1) for A=Ca, Sr, Ba and Pb, respectively. The structural features of the compounds were found similar to n=2-4 layers bismuth oxides. The strain caused by mismatch of cell parameter requirements for the [Bi₂O₂]²⁺ layers and perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks were relieved by tilting of the TiO₆ octahedra. Variable temperature synchrotron X-ray studies for Ca and Pb compounds showed that the orthorhombic structure persisted up to 675 and 475 K, respectively. Raman spectra of the compounds are also presented.     

Metal-organic deposition of YBa2Cu3Ox and Bi2Sr2Ca1Cu2Ox films on various substrates starting from different fluorine-free metallorganic compounds

YBa₂Cu₃O_x (Y-123) and Bi₂Sr₂Ca₁Cu₂O_x (Bi-2212) films on various substrates have been prepared by Metal-Organic Deposition starting from different metallorganic fluorine-free compounds and using a very simple instrumentation. The processing conditions include a rapid pyrolysis step in air and an annealing step in oxygen for Y-123 and in air for Bi-2212. The films obtained have been characterized by X-ray diffraction (XRD) and the formation of a superconducting phase of Y-123 or Bi-2212 was confirmed measuring the critical temperature (T _c) with Ac-susceptibility and resistive measurements. Microstructure and final cationic ratios have been studied by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).     

Decomposition of P2S2N4(Si(CH3)3)4A12C14 as Studied by FT-Raman and Quantum Chemistry Means

The dimeric title compound decomposes upon heating to give the monomer and desulphurized monomer as shown by FT-Raman and quantum chemical means.     

The crystal chemistry of Bi6TP2O15+x, T=Fe, Ni, Zn: Isomorphism and polymorphism, structural relationship to Bi6TiP2O16

The crystal structures of compounds with nominal compositions Bi₆FeP₂O_15+x (I), Bi₆NiP₂O_15+x (II) and Bi₆ZnP₂O_15+x (III) were determined from single-crystal X-ray diffraction data. They are monoclinic, space group I2, Z=2. The lattice parameters for (I) are a=11.2644(7), b=5.4380(3), c=11.1440(5) Å, β=96.154(4)°; for (II) a=11.259(7), b=5.461(4), c=11.109(7) Å, β=96.65(1)°; for (III) a=19.7271(5), b=5.4376(2), c=16.9730(6) Å, β=131.932(1)°. Least squares refinements on F² converged for (I) to R1=0.0554, wR₂=0.1408; for (II) R₁=0.0647, wR₂=0.1697; for (III) R₁=0.0385, wR₂=0.1023. The crystals are complexly twinned by 2-fold rotation about , by inversion and by mirror reflection. The structures consist of edge-sharing articulations of OBi₄ tetrahedra forming layers in the a-c plane that then continue by edge-sharing parallel to the b-axis. The three-dimensional networks are bridged by Fe and Ni octahedra in (I) and (II) and by Zn trigonal bipyramids in (III) as well as by oxygen atoms of the PO₄ moieties. Bi also randomly occupies the octahedral sites. Oxygen vacancies exist in the structures of the three compounds due to required charge balances and they occur in the octahedral coordination polyhedron of the transition metal. In compound (III), no positional disorder in atomic sites is present. The Bi-O coordination polyhedra are trigonal prisms with one, two or three faces capped. Magnetic susceptibility data for compound (I) were obtained between 4.2 and 350 K. Between 4.2 and 250 K it is paramagnetic, μ_eff=6.1 μ_B; a magnetic transition occurs above 250 K.     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.