A novel spinel coating on cobalt‐based Superalloy GH605 via an in‐situ oxidation approach

Cr‐Mn‐O spinel coating was prepared on the surface of cobalt‐based superalloy GH605 via an in‐situ oxidation method in H₂O‐H₂ environment. The composition, morphology, and chemical value state of the oxide spinel coatings were investigated by SEM, EDS, XRD, Raman spectra, and XPS. It indicated that the morphology of coating varied with oxidation temperature, and granular surface appeared when oxidation temperature increased to 1100°C. The formed Cr‐Mn‐O spinel coating was composed of Cr₂O₃ and MnCr₂O₄, and the thickness increased significantly with oxidation temperature. In the coating, Cr element existed in the state of Cr³⁺ ions and Cr⁶⁺ ions, while Mn element only existed in the form of Mn²⁺ ions.     

Preparation,Crystal Structure,Vibrational Spectra,and Thermal Behavior of Rb2H2P2O6·2H2O

Single crystals of Rb₂H₂P₂O₆ · 2H₂O could be obtained from aqueous solutions of hypodiphosphoric acid and rubidium carbonate. Its crystal structure was determined by X‐ray diffraction and it crystallizes in the monoclinic space group P2₁/c with Z = 4. The salt‐like title compound consists of [H₂P₂O₆]^2– units in staggered P₂O₆‐skeleton conformation, Rb⁺ cations, and H₂O molecules, held together by intermolecular hydrogen bonds of the type O ··· O. The vibrational spectra (IR/FIR and Raman) of the rubidium salt were recorded and an assignment of the vibrational modes is proposed based on the point group C_2h for the P₂O₆‐skeleton of the anion. The thermal behavior of Rb₂H₂P₂O₆ · 2H₂O is dominated by a complex TG decay indicating a simultaneous H₂O delivery coupled with a disproportionation of [H₂P₂O₆]^2–, what is also supported by Raman spectra of heated samples.     

(Zn1-xMnx)C2O4·2H2O在空气中的热分解动力学研究

用热分析（TG-DTG/DTA）、X射线衍射（XRD）技术和透射电镜（TEM）研究了固态物质Zn_1-xMn_xC₂O₄•2H₂O在空气中热分解的过程。热分析结果表明，Zn_1-xMn_xC₂O₄•2H₂O在空气中分两步分解，其失重率与理论计算失重率相吻合。 XRD和TEM结果表明，Zn_1-xMn_xC₂O₄•2H₂O分解的最终产物为Zn_1-xMn_xO,其颗粒大小约为10-13 nm。在非等温条件下对Zn_1-xMn_xC₂O₄•2H₂O的热分解动力学进行了分析。用Friedman法和Flynn-Wall-Ozawa(FWO)法求取了分解过程的活化能E，并用多元线性回归给出了可能的机理函数。Zn_1-xMn_xC₂O₄•2H₂O两步热分解的活化能分别为155.7513 kJ/mol 和215.9397 kJ/mol。     

New Borate‐citrate: Synthesis,Structure, and Properties of Sr[B(C6H5O7)2](H2O)4·3H2O

Single crystals of Sr[B(C₆H₅O₇)₂](H₂O)₄ · 3H₂O, a new borate‐citrate material, were grown with sizes up to 8 × 6 × 2 mm by slow evaporation of water at room temperature. The structure of Sr[B(C₆H₅O₇)₂](H₂O)₄ · 3H₂O was determined by single‐crystal X‐ray diffraction. It crystallizes in the monoclinic space group P2₁/c, with a = 11.363(3) Å, b = 18.829(4) Å, c = 11.976(3) Å, β = 110.736(3)°, and Z = 4. The SrO₈ dodecahedra, BO₄ tetrahedra and citrate groups are linked together to form chains. The compound was characterized by IR and UV/Vis/NIR transmittance spectroscopy as well as thermal analysis.     

A Facile Preparation of H2O2 Sensors Using Layer‐by‐Layer Deposited Thin Films Composed of Poly(ethyleneimine) and Carboxymethyl Cellulose as Matrices for Immobilizing Hemin

A layer‐by‐layer (LbL) thin film composed of poly(ethyleneimine) (PEI) and carboxymethyl cellulose (CMC) was prepared on the surface of a gold (Au) disk electrode and the LbL layer was impregnated with hemin to fabricate amperometric hydrogen peroxide (H₂O₂) sensors. Hemin can be easily immobilized in the LbL layer by immersing the LbL film‐coated electrode in the hemin solution. The hemin‐modified electrode thus prepared exhibited an amperometric response to H₂O₂ on the basis of the electrochemical reduction catalyzed by hemin. The output current of the hemin‐modified electrode depended on the concentration of H₂O₂ over the range of 0.005–1.0 mM. Thus, the LbL film composed of PEI and CMC was found to be an excellent material for the facile preparation of hemin‐based H₂O₂ sensors.     

Reaction of olefins using cerium(IV) sulfate tetrahydrate in carbonyl compounds–H2O

The reaction of olefins with cerium(IV) sulfate tetrahydrate [Ce(SO₄)₂·4H₂O, CS] in acetone–H₂O under reflux for 5 h gave 2‐oxo‐ and 2‐oxo‐5‐hydroxy derivatives. In this reaction, the yields of 2‐oxo‐5‐hydroxy derivatives were dependent on the quantity of H₂O. Moreover, the reaction of α, β‐unsaturated ketones with CS in acetone–H₂O yielded 2,7‐dioxo‐3‐hydroxy or 3,8‐dioxo‐4‐hydroxy derivatives. The reaction mechanism is also discussed. Copyright © 2005 John Wiley & Sons, Ltd.     

An Unlocked Two-Dimensional Conductive Zn-MOF on Polymeric Carbon Nitride for Photocatalytic H2O2 Production

Developing highly efficient catalytic sites for O₂ reduction to H₂O₂, while ensuring the fast injection of energetic electrons into these sites, is crucial for artificial H₂O₂ photosynthesis but remains challenging. Herein, we report a strongly coupled hybrid photocatalyst comprising polymeric carbon nitride (CN) and a two-dimensional conductive Zn-containing metal–organic framework (Zn-MOF) (denoted as CN/Zn-MOF(lc)/400; lc, low crystallinity; 400, annealing temperature in °C), in which the catalytic capability of Zn-MOF(lc) for H₂O₂ production is unlocked by the annealing-induced effects. As revealed by experimental and theoretical calculation results, the Zn sites coordinated to four O (Zn-O₄) in Zn-MOF(lc) are thermally activated to a relatively electron-rich state due to the annealing-induced local structure shrinkage, which favors the formation of a key *OOH intermediate of 2e⁻ O₂ reduction on these sites. Moreover, the annealing treatment facilitates the photoelectron migration from the CN photocatalyst to the Zn-MOF(lc) catalytic unit. As a result, the optimized catalyst exhibits dramatically enhanced H₂O₂ production activity and excellent stability under visible light irradiation.     

Palladium Nanoparticles Embedded into Graphene Nanosheets: Preparation,Characterization, and Nonenzymatic Electrochemical Detection of H2O2

A novel nonenzymatic H₂O₂ sensor based on a palladium nanoparticles/graphene (Pd‐NPs/GN) hybrid nanostructures composite film modified glassy carbon electrode (GCE) was reported. The composites of graphene (GN) decorated with Pd nanoparticles have been prepared by simultaneously reducing graphite oxide (GO) and K₂PdCl₄ in one pot. The Pd‐NPs were intended to enlarge the interplanar spacing of graphene nanosheets and were well dispersed on the surface or completely embedded into few‐layer GN, which maintain their high surface area and prevent GN from aggregating. XPS analysis indicated that the surface Pd atoms are negatively charged, favoring the reduction process of H₂O₂. Moreover, the Pd‐NPs/GN/GCE could remarkably decrease the overpotential and enhance the electron‐transfer rate due to the good contact between Pd‐NPs and GN sheets, and Pd‐NPs have high catalytical effect for H₂O₂ reduction. Amperometric measurements allow observation of the electrochemical reduction of H₂O₂ at 0.5 V (vs. Ag/AgCl). The H₂O₂ reduction current is linear to its concentration in the range from 1×10^?9 to 2×10^?3 M, and the detection limit was found to be 2×10^?10 M (S/N=3). The as‐prepared nonenzymatic H₂O₂ sensor exhibits excellent repeatability, selectivity and long‐term stability.     

Heteroatom Dopants Promote Two‐Electron O2 Reduction for Photocatalytic Production of H2O2 on Polymeric Carbon Nitride

Polymeric carbon nitride modified with selected heteroatom dopants was prepared and used as a model photocatalyst to identify and understand the key mechanisms required for efficient photoproduction of H₂O₂ via selective oxygen reduction reaction (ORR). The photochemical production of H₂O₂ was achieved at a millimolar level per hour under visible‐light irradiation along with 100 % apparent quantum yield (in 360–450 nm region) and 96 % selectivity in an electrochemical system (0.1 V vs. RHE). Spectroscopic analysis in spatiotemporal resolution and theoretical calculations revealed that the synergistic association of alkali and sulfur dopants in the polymeric matrix promoted the interlayer charge separation and polarization of trapped electrons for preferable oxygen capture and reduction in ORR kinetics. This work highlights the key features that are responsible for controlling the photocatalytic activity and selectivity toward the two‐electron ORR, which should be the basis of further development of solar H₂O₂ production.     

On the Search for H5O2+centered Water Clusters in the Gas Phase

In searching for H₅O₂⁺-centered water clusters, we employed vibrational predissociation spectroscopy and ab initio calculations. Structures of the clusters were characterized by the free- and hydrogen-bonded-OH stretches of ion cores and solvent molecules. Systematic examination of H⁺(H₂O)_5–7 in a supersonic expansion reveals the presence of both cyclic and noncyclic forms of H₅O₂⁺-centered water clusters. The proton transfer intermediate H₅O₂⁺(H₂O)₄ was identified, for the first time, by its characteristic hydrogen-bonded-OH stretches of the ion core at 3178 cm^?1. Also discovered at n = 7 is the H₅O₂⁺-containing five-membered ring isomer, whose existence is evidenced by the observation of a bonded-OH stretching doublet at 3544 and 3555 cm^?1 of the solvent molecules. The observations are in accord with ab initio calculations which forecast that H₅O₂⁺(H₂O)₄ and H₅O₂⁺(H₂O)₅ are, respectively, the lowest-energy isomers of protonated water hexamers and heptamers.     

Efficient hydroxylation of aromatic compounds catalyzed by an iron(II) complex with H2O2

A mononuclear iron(II) complex, Et₄N[Fe(C₁₀H₆NO₂)₃], coordinated by three 1‐nitroso‐2‐naphtholate ligands in a fac‐N₃O₃ geometry, was initiated to catalyze the direct hydroxylation of aromatic compounds to phenols in the presence of H₂O₂ under mild conditions. Various reaction parameters, including the catalyst dosage, temperature, mole ratio of H₂O₂ to benzene, reaction time and solvents which could affect the hydroxylation activity of the catalyst, were investigated systematically for benzene hydroxylation to obtain ideal benzene conversion and high phenol distribution. Under the optimum conditions, the benzene conversion was 10.2% and only phenol was detected. The catalyst was also found to be active towards hydroxylation of other aromatic compounds with high substrate conversions. The hydroxyl radical formed due to the reaction of the catalyst and H₂O₂ was determined to be the crucial active intermediate in the hydroxylation. A rational pathway for the formation of the hydroxyl radical was proposed and justified by the density functional theory calculations. Copyright © 2014 John Wiley & Sons, Ltd.     

Rotation–vibration energy levels from recent potential energy surfaces for the ground electronic states of NO2 and H2O

Using recently published potential energy surfaces, rovibrational energy levels are computed for the ground electronic states of H₂O and NO₂, using three‐dimensional discrete variable representation (DVR) algorithms. Calculations are presented for H₂O to demonstrate the accuracy of these algorithms. In the case of NO₂, comparisons with previous calculations are made as a test for the accuracy of the new potential energy surface. © 2000 John Wiley & Sons, Inc. Int J Quant Chem 76: 535–540, 2000     

Dissociation of sulfur oxoacids by two water molecules studied using ab initio and density functional theory calculations

Using ab initio [SCS‐MP2 and CCSD(T)] and density functional theory (M062X) calculations, we have studied the geometries and energies of sulfur oxoacids H₂S_mO₆ (m = 2–4) and their monohydrated and dihydrated clusters. When including the results from previously reported disulfuric acid (H₂S₂O₇) cases, the gas phase acidity is ordered as H₂S₂O₆ < H₂S₃O₆ < H₂S₂O₇ < H₂S₄O₆. The intramolecular H‐bonding, which may indicate the degree of structural flexibility in this molecular series, is an important factor for the order of the gas phase acidity. All these sulfur oxoacids show dissociated (or deprotonated) geometries with only two water molecules, although the energies of the dissociated conformers are ranked differently. All of the dissociated conformers form a unique H‐bonding network structure in which the protonated first water (H₃O⁺) is triply H‐bonded to each oxygen atom of two SO₃ moieties as well as the second water, which in turn is H‐bonded to a SO₃ moiety. H₂S₃O₆ has the best molecular flexibility for adopting such an H‐bonding network structure, and thereby all the low‐lying conformers of H₂S₃O₆(H₂O)₂ are dissociated. In contrast, the least flexible H₂S₂O₆ forms such a structure with a high strain, and dissociation of H₂S₂O₆(H₂O)₂ is found from the third lowest conformer. Although the gas phase acidity of H₂S₄O₆ is the highest in this series, the lowest dissociated conformer and the lowest undissociated conformer of H₂S₄O₆(H₂O)₂ are very close in energy. This is because forming the H‐bonding network structure is somewhat difficult due to the large distance between the two SO₃ moieties.     

A DFT Study on the Structure and Properties of Cu/Cr2O3 Catalyst

Using DFT method, the stable adsorption configurations of Cu₄ cluster on Cr₂O₃ (0001) surface were investigated. The regular tetrahedron structure and the planar structures were considered as the initial adsorption configuration of Cu₄ cluster, respectively. The adsorption energies of the two structures were also calculated. The simulation result indicated that the adsorption energy of the regular tetrahedron structure was higher than that of the planar structure, and thus the regular tetrahedron structure was confirmed to be the stable adsorption configuration for Cu₄ cluster on Cr₂O₃ (0001) surface. Moreover, it was observed that the Cu₄ cluster showed the definite stable adsorption sites on Cr₂O₃ (0001) surface, namely 3‐fold O sites. During the adsorption process of Cu₄ cluster onto Cr₂O₃ (0001) surface, the Cu₄ cluster could bond with more Cr or O atoms on the surface, and the apparent charge transfer also occurred correspondingly. Meanwhile, the Cu₄ cluster and Cr₂O₃ (0001) surface would bond in the form of local polarization to enhance the stability of adsorption configuration.     

Criegee自由基CH2O2与H2O反应机理及动力学的理论研究

在6-311＋G(2d,2p)水平下, 采用密度泛函理论(DFT)的B3LYP方法, 研究了Criegee 自由基CH₂O₂与H₂O的反应. 结果表明反应存在三个通道: CH₂O₂＋H₂O®HOCH₂OOH (R1); CH₂O₂＋H₂O®HCO＋OH＋H₂O (R2); CH₂O₂＋H₂O®HCHO＋H₂O₂ (R3), 各通道的势垒高度分别为43.35, 85.30和125.85 kJ/mol. 298 K下主反应通道(R1)的经典过渡态理论(TST)与变分过渡态理论(CVT)的速率常数k^TST与k^CVT均为2.47×10^－17 cm³•molecule^－1•s^－1, 而经小曲率隧道效应模型(SCT)校正后的速率常数k^CVT/SCT为 5.22×10^－17 cm³•molecule^－1•s^－1. 另外, 还给出了200～2000 K 温度范围内拟合得到的速率常数随温度变化的三参数Arrhenius方程.     

Synthesis and Thermodynamic Properties of MgO·B_2O_3·4H_2O

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｒｅａｒｅｍａｎｙｋｉｎｄｓｏｆｍａｇｎｅｓｉｕｍｂｏｒａｔｅｓ ,ｂｏｔｈｎａｔｕｒａｌａｎｄｓｙｎｔｈｅｔｉｃ .Ａｂｏｒａｔｅｄｏｕｂｌｅｓａｌｔ (2ＭｇＯ·2Ｂ2 Ｏ3 ·ＭｇＣｌ2 · 14Ｈ2 Ｏ)ｎａｍｅｄｃｈｌｏｒｏｐｉｎｎｏｉｔｅｗａｓｏｂ ｔａｉｎｅｄｆｒｏｍｔｈｅｎａｔｕｒａｌｃｏｎｃｅｎｔｒａｔｅｄｓａｌｔｌａｋｅｂｒｉｎｅ .1Ｉｎｏｒｄｅｒｔｏｆｉｎｄｔｈｅｆｏｒｍｉｎｇｒｅｌａｔｉｏｎｂｅｔｗｅｅｎｔｈｅｄｏｕｂｌｅｓａｌｔａｎｄｍａｇｎｅｓｉｕｍ ｂｏｒａ…     

Rational Design of Crystalline Covalent Organic Frameworks for Efficient CO2 Photoreduction with H2O

Solar energy‐driven conversion of CO₂ into fuels with H₂O as a sacrificial agent is a challenging research field in photosynthesis. Herein, a series of crystalline porphyrin‐tetrathiafulvalene covalent organic frameworks (COFs) are synthesized and used as photocatalysts for reducing CO₂ with H₂O, in the absence of additional photosensitizer, sacrificial agents, and noble metal co‐catalysts. The effective photogenerated electrons transfer from tetrathiafulvalene to porphyrin by covalent bonding, resulting in the separated electrons and holes, respectively, for CO₂ reduction and H₂O oxidation. By adjusting the band structures of TTCOFs, TTCOF‐Zn achieved the highest photocatalytic CO production of 12.33 μmol with circa 100 % selectivity, along with H₂O oxidation to O₂. Furthermore, DFT calculations combined with a crystal structure model confirmed the structure–function relationship. Our work provides a new sight for designing more efficient artificial crystalline photocatalysts.     

A quantitative colorimetric assay of H2O2 and glucose using silver nanoparticles induced by H2O2 and UV

A simple spectrophotometric assay of H2O2 and glucose using Ag nanoparticles has been carried out. Relying on the synergistic effect of H2O2 reduction and ultraviolet （UV） irradiation, Ag nanoparticles with enhanced absorption signals were synthesized. H2O2 served as a reducing agent in the Ag nanoparticles formation in which Ag＋ was reduced to Ago by O2- generated via the decomposition of H2O2 in alkaline media. On the other hand, photoreduction of Ag＋ to Ago under UV irradiations also contributed to the nanoparticles formation. The synthesized nanoparticles were characterized by TEM, XPS, and XRD. The proposed method could determine H2O2 with concentrations ranging from 5.0× 10^-7 to 6.0× 10^-5 tool/ L The detection limit was estimated to be 2.0 × 10^-7 mol/L. Since the conversion of glucose to gluconic acid catalyzed by glucose oxidase was companied with the formation of H2O2, the sensing protocol has been successfully utilized for the determination of glucose in human blood samples. The results were in good agreement with those determined by a local hospital. This colorimetric sensor thus holds great promises in clinical applications.     

One‐step immersion method for fabricating superhydrophobic aluminum alloy with excellent corrosion resistance

This work develops a facile one‐step immersion method for preparing the superhydrophobic aluminum alloy, i.e. the aluminum alloy is treated with stearic acid (STA)–ethanol–H₂O solution at 60 °C for 35 h. Results show that the aluminum alloy achieves flower‐like structure with both a great deal of pillars and pores, while the long hydrophobic alkyl chains are chemically grafted onto the hierarchical surface. Meanwhile, the water contact angle at the aluminum alloy surface gradually enhances with the decrease of the ethanol–H₂O volume ratio, and the water contact angle and rolling angle of 156.2° and 5°, respectively, are obtained when the ethanol–H₂O volume ratio is 1:3. Moreover, results show that the higher water contact angle at the aluminum alloy, the better corrosion resistance of the aluminum alloy. Consequently, the aluminum alloy with the superhydrophobic property has the best corrosion resistance, durability, and stability in corrosive environments. Copyright © 2016 John Wiley & Sons, Ltd.