Degradation of n-butylparaben and 4-tert-octylphenol in H2O2/UV system

The degradation of two endocrine disrupting compounds: n-butylparaben (BP) and 4-tert-octylphenol (OP) in the H₂O₂/UV system was studied. The effect of operating variables: initial hydrogen peroxide concentration, initial substrate concentration, pH of the reaction solution and photon fluency rate of radiation at 254 nm on reaction rate was investigated. The influence of hydroxyl radical scavengers, humic acid and nitrate anion on reaction course was also studied. A very weak scavenging effect during BP degradation was observed indicating reactions different from hydroxyl radical oxidation. The second-order rate constants of BP and OP with OH radicals were estimated to be 4.8×10⁹ and 4.2×10⁹ M^?1 s^?1, respectively. For BP the rate constant equal to 2.0×10¹⁰ M^?1 s^?1was also determined using water radiolysis as a source of hydroxyl radicals.     

Choline biosensors based on a bi-electrocatalytic property of MnO2 nanoparticles modified electrodes to H2O2

An interesting mode of reactivity of MnO₂ nanoparticles modified electrode in the presence of H₂O₂ is reported. The MnO₂ nanoparticles modified electrodes show a bi-direction electrocatalytic ability toward the reduction/oxidation of H₂O₂. Based on this property, a choline biosensor was fabricated via a direct and facile electrochemical deposition of a biocomposite that was made of chitosan hydrogel, choline oxidase (ChOx) and MnO₂ nanoparticles onto a glassy carbon (GC) electrode. The biocomposite is homogeneous and easily prepared and provides a shelter for the enzyme to retain its bioactivity. The results of square wave voltammetry showed that the electrocatalytic reduction currents increased linearly with the increase of choline chloride concentration in the range of 1.0 × 10⁻⁵ –2.1 × 10⁻³ M and no obvious interference from ascorbic acid and uric acid was observed. Good reproducibility and stability were obtained. A possible reaction mechanism was proposed.     

Synthesis of silver nanoparticles supported on silica aerogel using gamma radiolysis

Silver clusters on SiO₂ support have been synthesized using ⁶⁰Co gamma radiation. The irradiation of Ag⁺ in aqueous suspension of SiO₂ in the presence of 0.2 mol dm⁻³ isopropanol resulted in the formation of yellow suspension. The absorption spectrum showed a band at 408 nm corresponding to typical characteristic surface plasmon resonance of Ag nanoparticles. The effect of Ag⁺ concentration on the formation of Ag cluster indicated that the size of Ag clusters vary with Ag⁺ concentration, which was varied from 4×10⁻⁴ to 5×10⁻³ mol dm⁻³. The results showed that Ag clusters are stable in the pH range of 2–9 and start agglomerating in the alkaline region at pH above 9. The effect of radiation dose rate and ratio of Ag⁺/SiO₂ on the formation of Ag clusters have also been investigated. The prepared clusters have been characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), which showed the particle size of Ag clusters to be in the range of 10–20 nm.     

Mass spectrometric study of the dissociation of Group XI metal complexes with fatty acids and glycerolipids: Ag2H+ and Cu2H+ ion formation in the presence of a double bond

Results of mass spectrometric studies are reported for the collisional dissociation of Group XI (Cu, Ag, Au) metal ion complexes with fatty acids (palmitic, oleic, linoleic and α-linolenic) and glycerolipids. Remarkably, the formation of M₂H⁺ ions (M = Cu, Ag) is observed as a dissociation product of the ion complexes containing more than one metal cation and only if the lipid in the complex contains a double bond. Ag₂H⁺ is formed as the main dissociation channel for all three of the fatty acids containing double bonds that were investigated while Cu₂H⁺ is formed with one of the fatty acids and, although abundant, is not the dominant dissociation channel. Also, Cu(I) and Ag(I) ion complexes were observed with glycerolipids (including triacylglycerols and glycerophospholipids) containing either saturated or unsaturated fatty acid substituents. Interestingly, Ag₂H⁺ ion is formed in a major fragmentation channel with the lipids that are able to form the complex with two metal cations (triacylglycerols and glycerophosphoglycerols), while lipids containing a fixed positive charge (glycerophospocholines) complex only with a single metal cation. The formation of Ag₂H⁺ ion is a significant dissociation channel from the complex ion [Ag₂(L–H)]⁺ where L = Glycerophospholipid (GP) (18:1/18:1). Cu(I) also forms complexes of two metal cations with glycerophospholipids but these do not produce Cu₂H⁺ upon dissociation. Rather organic fragments, not containing Cu(I), are formed, perhaps due to different interactions of these metal cations with lipids resulting from the much smaller ionic radius of Cu(I) compared to Ag(I).     

Hemoglobin co-immobilized with silver–silver oxide nanoparticles on a bare silver electrode for hydrogen peroxide electroanalysis

Hemoglobin (Hb) and silver–silver oxide (Ag–Ag₂O) nanoparticles were co-immobilized on a bare silver electrode surface by cyclic voltammetry, and were characterized by UV–vis reflection spectroscopy, scanning electron microscopy, and electrochemical impedance spectroscopy. The immobilized Hb was shown to maintain its biological activity well. Direct electron transfer between Hb and the resulting electrode was achieved without the aid of any electron mediator. The reduction currents to hydrogen peroxide (H₂O₂) at co-immobilized electrodes showed a linear relationship with H₂O₂ concentration over a concentration range from 6.0?×?10^?6 to 5.0?×?10^?2 mol L^?1, and a detection limit of 2.0?×?10^?6 mol L^?1 (S/N?=?3).     

Porous cuprous oxide microcubes for non-enzymatic amperometric hydrogen peroxide and glucose sensing

Using porous cuprous oxide (Cu₂O) microcubes, a simple non-enzymatic amperometric sensor for the detection of H₂O₂ and glucose has been fabricated. Cyclic voltammetry (CV) revealed that porous Cu₂O microcubes exhibited a direct electrocatalytic activity for the reduction of H₂O₂ in phosphate buffer solution and the oxidation of glucose in an alkaline medium. The non-enzymatic amperometric sensor used in the detection of H₂O₂ with detection limit of 1.5 × 10^?6 M over wide linear detection ranges up to 1.5 mM and with a high sensitivity of 50.6 μA/mM. This non-enzymatic voltammetric sensor was further utilized in detection of glucose with a detection limit of 8.0 × 10^?7 M, a linear detection range up to 500 μM and with a sensitivity of ?70.8 μA/mM.     

About the OH yield in the radiolysis of an aqueous/H2O2 system. Its optimisation for water treatment

Unless the radiolytic reducing species are neutralised or converted into oxidising species, an EB remediation system cannot be considered a true Advanced Oxidation Processes (AOP). A water/H₂O₂ system irradiated by UVC mercury lamps constitutes a widely used OH production method. Employing H₂O₂ in radiolysis as well, an enhancement of the oxidative efficiency of an EB treatment can be obtained. Pulse radiolysis measurements of an aerated aqueous/H₂O₂/KSCN system have been systematically undertaken to assess the optimal H₂O₂ concentration. By linearly fitting a competition kinetics relationship, it is found that the scavengeable extra-yield of OH is ΔG(OH)=0.24 μmol J^?1 (R=0,9958), while the maximum experimental yield is measured G(OH)_max=(0.52±0.02) μmol J^?1 when [H₂O₂]=5–10 mM. Exceeding these concentrations the OH yield drops off.     

Effect of irradiation on photoluminescence and optical absorption spectra of Li2B4O7:Mn and Li2B4O7:Ag single crystals

Effects induced by high-dose irradiation on manganese- and silver-doped Li₂B₄O₇ (lithium tetraborate, LTB) single crystals were monitored by photoluminescence and optical absorption spectroscopy. High-dose (1.0×10³ and 1.2×10⁴ Gy) irradiation of the samples was performed using high-energy, short-time (4 MeV, 2.6 μs) electron pulses of a linear electron accelerator. Changes in the oxidation states of dopants were revealed. Recharging of manganese Mn²⁺→Mn³⁺ and Ag⁺→Ag⁰ were observed. Ionization process Mn²⁺→Mn³⁺+e⁻ and creation of Ag⁰-nanoparticles are supposed.     

A sensitivity-controlled hydrogen peroxide sensor based on self-assembled Prussian Blue modified electrode

In this communication, a hydrogen peroxide (H₂O₂) sensor based on self-assembled Prussian Blue (PB) modified electrode was reported. Thin film of PB was deposited on the electrode by self-assembly process including multiple sequential adsorption of ferric ions and hexacyanoferrate ions. The as-prepared PB modified electrode displayed sufficient stability for practical sensing application. At an applied potential of ?0.05 V vs. Ag/AgCl (sat. KCl), PB modified electrode with 30 layers exhibited a linear dependence on H₂O₂ concentration in the range of 1 × 10^?6–4 × 10^?4 M (r = 0.9998) with a sensitivity of 625 mA M^?1 cm^?2. It was found that the sensitivity of H₂O₂ sensors could be well controlled by adjusting the number of deposition cycles for PB preparation. This work demonstrates the feasibility of self-assembled PB modified electrode in sensing application, and provides an effective approach to control the sensitivity of PB-based amperometric biosensors.     

Solvothermal synthesis and crystal structure of the Mo(VI)-bridged helical chain containing Mo2(V) dimers: (C4H12N2)2[(MoV2O4)(MoVIO4)(C2O4)2]·2H2O

A new molybdenum complex (C₄H₁₂N₂)₂[(Mo^V₂O₄)(Mo^VIO₄)(C₂O₄)₂]·2H₂O, was solvothermally synthesized and characterized by single-crystal X-ray diffraction. The structure of the compound consists of oxalate acid-coordinated mixed-valent [Mo^V₂O₄][Mo^VIO₄] helical chains and protonated piperazine cations. The helical chains are built up from the [Mo^V₂O₄] units and [Mo^VIO₄] tetrahedral. The central axis about helical chain is a 2-fold screw axis. The compound crystallizes in the space group P2₁/n of monoclinic system with a = 11.396(2) Å, b = 14.107(3) Å, c = 15.805(3) Å, β = 102.09(3)°, V = 2484.6(9) Å³, Z = 4. Other characterizations by elemental analysis, IR, and thermal analysis for this compound are also given.     

Palladium Nanoparticles Embedded into Graphene Nanosheets: Preparation,Characterization, and Nonenzymatic Electrochemical Detection of H2O2

A novel nonenzymatic H₂O₂ sensor based on a palladium nanoparticles/graphene (Pd‐NPs/GN) hybrid nanostructures composite film modified glassy carbon electrode (GCE) was reported. The composites of graphene (GN) decorated with Pd nanoparticles have been prepared by simultaneously reducing graphite oxide (GO) and K₂PdCl₄ in one pot. The Pd‐NPs were intended to enlarge the interplanar spacing of graphene nanosheets and were well dispersed on the surface or completely embedded into few‐layer GN, which maintain their high surface area and prevent GN from aggregating. XPS analysis indicated that the surface Pd atoms are negatively charged, favoring the reduction process of H₂O₂. Moreover, the Pd‐NPs/GN/GCE could remarkably decrease the overpotential and enhance the electron‐transfer rate due to the good contact between Pd‐NPs and GN sheets, and Pd‐NPs have high catalytical effect for H₂O₂ reduction. Amperometric measurements allow observation of the electrochemical reduction of H₂O₂ at 0.5 V (vs. Ag/AgCl). The H₂O₂ reduction current is linear to its concentration in the range from 1×10^?9 to 2×10^?3 M, and the detection limit was found to be 2×10^?10 M (S/N=3). The as‐prepared nonenzymatic H₂O₂ sensor exhibits excellent repeatability, selectivity and long‐term stability.     

Two novel Keggin tungstocobaltates grafted by cobaltII complex group(s): K[Co(phen)2(H2O)]2[HCoW12O40]·2H2O and [Co(2,2′-bipy)3]1.5{[Co(2,2′-bipy)2(H2O)][HCoW12O40]}·0.5H2O

Two novel inorganic–organic hybrid compounds composed of Keggin tungstocobaltate framework and cobalt(II)–N coordination complexes, K[Co(phen)₂(H₂O)]₂[HCoW₁₂O₄₀]·2H₂O (1) (phen = 1,10-phenanthroline) and [Co(2,2′-bipy)₃]_1.5{[Co(2,2′-bipy)₂(H₂O)][HCoW₁₂O₄₀]·0.5H₂O (2) (bipy = bipyridine), have been synthesized under hydrothermal conditions by directly using Keggin POMs as starting materials, which were characterized by elemental analyses, IR, TG analyses and X-ray single crystal diffraction. Crystal data for compound 1: C₄₈H₄₁Co₃KN₈O₄₄W_12, triclinic, space group P-1, a = 10.918(5) Å, b = 13.401(5) Å, c = 13.693(5) Å, α = 69.291(5)°, β = 71.568(5)°, γ = 78.421(5)°, V = 1768.9(12) Å³, Z = 1; for compound 2: C₁₃₀H₁₀₄Co₇N₂₆O₈₃W_24, orthorhombic, space group, C2/c, a = 46.839(9) Å, b = 14.347(3) Å, c = 26.147(5) Å, α = β = γ = 90°, V = 17,570(6) Å³, Z = 4. Compound 1 exhibits a pseudo-1D chainlike structure, in which potassium ions act as linkages of Keggin unit doubly grafted by [Co(phen)₂(H₂O)] complex. Compound 2 represents a [Co(2,2′-bipy)₂(H₂O)]²⁺ mono-grafted Keggin tungstocobaltate derivative with 1.5[Co(2,2′-bipy)₃]²⁺ countercations. The cyclic voltammetric behavior of 1-CPE is similar to the parent 3-CPE, but the cyclic voltammetric behavior of Co^II shows a little difference. Variable-temperature magnetic susceptibility measurement of compound 1 demonstrates the presence of antiferromagnetic interactions.     

Ferrocene-modified Fe3O4@SiO2 magnetic nanoparticles as building blocks for construction of reagentless enzyme-based biosensors

A novel amperometric glucose biosensor was developed by entrapping glucose oxidase (GOD) in chitosan (CS) composite doped with ferrocene monocarboxylic acid-modified magnetic core-shell Fe₃O₄@SiO₂ nanoparticles (FMC-AFSNPs). It is shown that the obtained magnetic bio-nanoparticles attached to the surface of a carbon paste electrode (CPE) with the employment of a permanent magnet showed excellent electrochemical characteristics and at the same time acted as mediator to transfer electrons between the enzyme and the electrode. Under optimal conditions, this biosensor was able to detect glucose in the linear range from 1.0 × 10⁻⁵ to 4.0 × 10⁻³ M with a detection limit of 3.2 μM (S/N = 3). This immobilization approach effectively improved the stability of the electron transfer mediator and is promising for construction of biosensor and bioelectronic devices.     

Nonenzymatic H2O2 Electrochemical Sensor Based on SnO2‐NPs Coated Polyethylenimine Functionalized Graphene

This paper demonstrated using polyethylenimine (PEI)‐functionalized graphene (Gr) incorporating tin oxide (SnO₂) hybrid nanocomposite as a platform for nonenzymatic H₂O₂ electrochemical sensor. The results of UV‐vis spectroscopy and X‐ray diffraction (XRD) confirmed the simultaneous formation of tin oxide (SnO₂) nanocomposite and reduction of graphene oxide (GO). Transmission electron microscopy (TEM) images showed a uniform distribution of nanometer‐sized tin oxide nanoparticles on the grapheme sheets, which could be achieved using stannous chloride (SnCl₂) complex instead of tin oxide as precursor. The electrochemical measurements, including cyclic voltammetry (CV) and amperometric performance (I‐t), showed that the PEI‐functionalized Gr supported SnO₂ (SnO₂‐PEI‐Gr) exhibited an excellent electrocatalytic activity toward the H₂O₂. The corresponding calibration curve of the current response showed a linear detection range of 9×10⁻⁶∼1.64×10⁻³ mol L⁻¹, while the limit of detection was estimated to be 1×10⁻⁶ mol L⁻¹. Electrochemical studies indicated that SnO₂ and functionalized Gr worked synergistically for the detection of H₂O₂.     

Measurement and correlation of the solubility of MnSO4·H2O with MgSO4·7H2O in MeOH + H2O solution

Data on the solubility of manganese sulphate monohydrate in water, and in aqueous alcohols is essential for salting-out crystallization studies. The solubilities for the quaternary system MnSO₄·H₂O + MgSO₄·7H₂O + H₂O + MeOH solution were determined in the temperature ranges 293.2–308.2 K over the mole fraction methanol ranges of 0.00–0.16. The solubility data were used for modelling with the modified extended electrolyte non-random two-liquid (NRTL) equation. The present extension uses ion-specific parameters instead of the electrolyte-specific NRTL binary interaction parameters. This approach has feasibility for many electrolytes and mixed aqueous solution systems principally. The model was found to correlate the solubility data satisfactory.     

A Sensitive and Renewable Chlortoluron Molecularly Imprinted Polymer Sensor Based on the Gate‐Controlled Catalytic Electrooxidation of H2O2 on Magnetic Nano‐NiO

A new sensor was fabricated by MIP synthesized on the surface of magnetic nickel(II) oxide (NiO) nanoparticles which based on the oxidation current change of H₂O₂. Chlortoluron was selected as template which can be detected indirectly by the decrease of the H₂O₂ oxidation current on the NiO nanoparticle‐modified GCE caused by the blocking access after rebinding. A high sensitivity was obtained because of the high catalytic effect of NiO nanoparticles on H₂O₂ oxidation. Chlortoluron was determined from 1.0×10^?8/L to 1.0×10^?4 mol/L, with a detection limit of 2.4×10^?9 mol/L. The proposed method combines the high sensitivity of the catalytic effect and the high selectivity of the MIP technique. Water samples were assayed using the MIP sensor, and recoveries of 96.9 % to 104.7 % were obtained.     

Synthesis of Functionalized MWCNTs Decorated with Copper Nanoparticles and Its Application as a Sensitive Sensor for Amperometric Detection of H2O2

Functionalized‐multiwall carbon nanotubes decorated with redox active copper nanoparticles have been fabricated for sensitive enzyme‐less H₂O₂ detection. The new nanocomposite was characterized by Transmission electron microscopy, energy dispersive X‐ray analysis and cyclic voltammetry. The response of the modified electrode to H₂O₂ was examined using amperometry at ?0.45 V vs. Ag/AgCl in a buffer solution at pH 10.0. The developed sensor displayed linear concentration ranges of 0.5–10.0 and 10.0–10000.0 µmol L^?1 with a detection limit of 0.3 µmol L^?1. The proposed sensor displayed good selectivity for H₂O₂ detection in the presence of common interferences such as ascorbic acid.     

An enzymatic glucose/O2 biofuel cell: Preparation,characterization and performance in serum

This study demonstrates a new kind of single-walled carbon nanotubes (SWNT)-based compartment-less glucose/O₂ biofuel cell (BFC) with glucose dehydrogenase (GDH) and bilirubin oxidase (BOD) as the anodic and cathodic biocatalysts, respectively, and with poly(brilliant creysl blue) (BCB) adsorbed onto SWNT nanocomposite as the electrocatalyst for the oxidation of NADH. The prepared GDH-polyBCB-SWNT bioanode exhibits an excellent electrocatalytic activity toward the oxidation of glucose biofuel; in 0.10 M phosphate buffer containing 20 mM NAD⁺ and 100 mM glucose, the oxidation of glucose commences at −0.25 V and the current reaches its maximum of 310 μA/cm² at −0.05 V vs. Ag/AgCl. At the BOD-SWNT biocathode, a high potential output is achieved for the reduction of O₂ due to the direct electron transfer property of BOD at the SWNTs. In 0.10 M phosphate buffer, the electrocatalytic reduction of O₂ is observed at a high potential of 0.53 V vs. Ag/AgCl with an electrocatalytic current plateau of ca. 28 μA/cm² at 0.45 V under ambient air and ca. 102 μA/cm² under O₂-saturated atmosphere. In 0.10 M phosphate buffer containing 10 mM NAD⁺ and 40 mM glucose under O₂-saturated atmosphere, the power density of the assembled SWNT-based glucose/O₂ BFC reaches 53.9 μW/cm² at 0.50 V. The performance and the stability of the glucose/O₂ BFC are also evaluated in serum. This study could offer a new route to the development of new kinds of enzymatic BFCs with a high performance and provide useful information on future studies on the enzymatic BFCs as in vivo power sources.     

New α,ω-dicarboxylate coordination polymers with 4,4′-bipyridine: Cu(bpy)(C5H6O4), Zn(bpy)(C5H6O4), Zn(bpy)(C6H8O4) and Mn(bpy)(C8H12O4) · H2O

Four 4,4′-bipyridine α,ω-dicarboxylate coordination polymers Cu(bpy)(C₅H₆O₄) (1), Zn(bpy)(C₅H₆O₄) (2), Zn(bpy)(C₆H₈O₄) (3) and Mn(bpy)(C₈H₁₂O₄) · H₂O (4) have been synthesized and structurally characterized by single crystal X-ray diffraction methods (bpy = 4,4-bipyridine, (C₅H₆O₄)²⁻ = glutarate anion, (C₆H₈O₄)²⁻ = adipate anion, (C₈H₁₂O₄)²⁻ = suberate anion). Their crystal structures are featured by dimeric metal units, which are co-bridged by 4,4′-bipyridine ligands and dicarboxylate anions such as glutarate, adipate and suberate anions to generate 2D layers with a (4,4) topology in 1, 2 and 4 as well as to form 3D frameworks in 3. Two 3D frameworks in 3 interpenetrate with each other to form a topology identical to the well-known Nb₆F₁₅ cluster compound. Over 5–300 K, the paramagnetic behavior of 4 follows the Curie–Weiss law χ_m(T − Θ) = 4.265(5) cm³ mol⁻¹ with the Weiss constant Θ = −6.3(2) K. Furthermore, the thermal behavior of 3 and 4 is also discussed.     

Potential energy surface and rate constant of the inversion substitution reactions CH3X + O2 → CH3O2• + X• (X = SH,NO2)

The temperature dependence of the rate constant of the inversion substitution reactions CH₃X + O₂ → CH₃O₂^? + X^? (X = SH, NO₂), can be expressed as k = 6.8 × 10^–12(T/1000)^1.49exp(–62816 cal mol^–1/RT) cm³ s^–1 (X = SH) and k = 6.8 × 10^–12(T/1000)^1.26 × × exp(–61319 cal mol^–1/RT) cm³ s^–1 (X = NO₂), as found with the use of high-level quantum chemical methods and the transition state theory.