多孔氧化铝及其前躯体的制备与表征

γ-Al2O3主要来源于其前驱体勃姆石(AlOOH),由于具有高的比表面积,常作为催化剂载体和吸附剂。该文以Al(NO)3·9H2O和NaOH为原料,采用溶胶凝胶法制备出了高比表面积的AlOOH,经过热处理得到丛状的多孔性γ-Al2O3。并利用X射线衍射(XRD)、场发射扫描电镜(SEM)和N2吸附-脱附技术对所得的产物进行表征。     

硅含量对Al2O3-SiO2气凝胶结构和性能的影响

研究了硅含量对Al2O3-SiO2气凝胶结构和性能的影响.结果表明,随着硅含量的增加,Al2O3-SiO2溶胶的凝胶时间逐渐延长,气凝胶密度逐渐增大.其结构逐渐由多晶勃姆石向无定形SiO2过渡.Al2O3-SiO2气凝胶同时含有Al-O、Si-O以及Al-O-Si结构,600 ℃煅烧后的物相为无定形γ-Al2O3和SiO2,1 200 ℃煅烧后为莫来石相.当硅含量为6.1wt%～13.1wt%时,适量的硅抑制了Al2O3-SiO2气凝胶的相变,其1 000℃的比表面积(339～445 m2·g-1)高于纯Al2O3气凝胶(157 m2·g-1).SEM分析表明,硅元素的加入改变了Al2O3气凝胶的结构形貌,随着硅含量的增大,Al2O3-SiO2气凝胶逐渐由针叶状或长条状向球状颗粒转变.     

大比表面积γ-Al2O3的制备及辅助剂蔗糖的用量对γ-Al2O3 织构的影响

 在由硝酸铝经氨水沉淀制备氧化铝的过程中,用蔗糖作为辅助剂制得了具有大比表面积的γ-Al2O3,并考察了蔗糖加入量对γ-Al2O3织构的影响. 将硝酸铝和蔗糖共溶于水,滴加氨水至Al3+全部沉淀(pH=5.2),所得沉淀连同母液一起在80 ℃水浴中搅拌得到溶胶,将溶胶于110 ℃失水后即得凝胶. 凝胶进一步失水后发生燃烧得到含碳的前体,再经600 ℃焙烧即得到γ-Al2O3(比表面积可达350 m2/g左右). 利用差热-热重分析、元素分析、氮吸附-脱附等温线、X射线粉末衍射和透射电子显微镜对前体及 γ-Al2O3 样品进行了表征. 结果表明,γ-Al2O3不但具有大的比表面积,而且孔径较小,分布较为集中. 通过改变蔗糖的用量,还可在一定程度上对γ-Al2O3的比表面积和孔结构等进行调控.     

负载Cu氧化铝纳米管合成及在NO+CH4反应中催化性能研究

采用过氧化氢调节反应条件,在水热体系中合成了新型的勃姆石纳米管,经520℃焙烧2h后,晶型由AlOOH转化为γ-Al2O3;采用XRD、氮吸附、TEM等对合成的纳米管进行表征.结果表明,合成的γ-Al2O3纳米管长约300nm,外径20nm,比表面积达到230m2/g以上.以此为载体,采用等体积浸渍法用Cu(NO3)2...     

稀土铕离子掺杂对拟薄水铝石晶体结构和相变的影响

研究了Eu3+离子对拟薄水铝石高温相变及微结构的影响。XRD及热分析结果表明,拟薄水铝石在560,882及1224℃分别经历-γAlOOH→-γAl2O3,γ-Al2O3→-θAl2O3和-θAl2O3→-αAl2O3相变。Eu3+掺杂后-γAlOOH→-γAl2O3相变温度不变,-γAl2O3→-θAl2O3和-θAl2O3→-αAl2O3相变温度分别提高到1054和1237℃。晶胞体积增大及衍射峰2θ值减小说明Eu3+离子以部分离子取代的形式进入-γAl2O3及-θAl2O3晶格。Eu3+离子进入晶格抑制了γ-Al2O3及-θAl2O3晶粒生长速率。-θAl2O3→-αAl2O3相变过程中Eu3+离子随Al3+一起迁移,并与Al3+离子及O2-离子形成了一个新生化合物相EuAl12O19。分析认为,该化合物在-αAl2O3晶界间存在,阻碍了-θAl2O3→-αAl2O3相转变过程中离子扩散速率,使-θAl2O3→-αAl2O3相变活化能由822.0提高到1063.15 kJ.mol-1。Eu3+离子掺杂使-θAl2O3→-αAl2O3相变过程由形核控制转变为表面扩散控制。     

KBF4非等温固-固相变热性质的测定

利用DTA-TG和DSC热分析技术研究了无机塑晶材料KBF4固-固相变的热性能,测得转变温度为284.13℃,转变焓为105.73J/g.KBF4固-固相变的机理是随着温度的升高,晶体中离子键部分断裂,晶体逐渐由低对称的正交晶系向高对称立方晶系转变,并在这过程中,同时引入化学键的振动和转动无序,从而吸收大量的相变焓.     

临氢水热处理对Ni/γ-Al_2O_3催化剂结构和性能的影响

采用浸渍法制备了Ni负载量为17%的Ni/γ-Al2O3催化剂.在氢气压力4 MPa,温度180℃条件下对Ni/γ-Al2O3催化剂进行了不同时间的水热处理.通过XRD、TG、H2-TPR和低温氮气物理吸附等手段对水热处理前后的催化剂进行表征,并考察其催化1,4-丁炔二醇加氢反应性能.结果表明,临氢水热处理导致载体γ-Al2O3水合相变为薄水铝石,随着水热处理时间的延长,薄水铝石的结晶度逐渐增大.γ-Al2O3的水合相变引起活性组分Ni晶粒的聚集及催化剂比表面积和孔容下降,从而导致催化剂活性降低.     

焙烧温度对CuO/γ-Al2O3和CeO2-CuO/γ-Al2O3催化剂NO还原活性的影响

用浸渍法制备了CuO/γ-Al2O3催化剂和CeO2改性的CeO2-CuO/γ-Al2O3催化剂,考察了焙烧温度对CuO/γ-Al2O3和CeO2-CuO/γ-Al2O3催化剂C3H6还原NO反应活性的影响,以及CeO2的添加量对CeO2-CuO/γ-Al2O3催化剂C3H6还原NO反应活性的影响。结果表明,在200 ℃～500 ℃的焙烧温度范围内,焙烧温度对CuO/γ-Al2O3催化剂的活性影响很小；在500 ℃～800 ℃的焙烧温度范围内,随着焙烧温度的升高CuO/γ-Al2O3催化剂的活性急剧下降,由XRD物相测定结果可知,归因于对反应表现惰性的尖晶石CuAl2O4相的生成。当焙烧温度为500 ℃时,CeO2的添加对CuO/γ-Al2O3催化剂的活性影响很小；当焙烧温度为800 ℃时,CeO2的添加对CuO/γ-Al2O3催化剂有明显的助催化作用,当Ce和Cu的摩尔比为1∶10时,NO转化率较为理想。     

烟酰胺腺嘌呤二核苷酸磷酸与纳米氧化铝和勃姆石的作用

采用多种现代分析手段研究了烟酰胺腺嘌呤二核苷酸磷酸(NADP+)与纳米氧化铝(γ-Al2O3)和纳米勃姆石(γ-AlOOH)的相互作用,结果显示NADP+与γ-AlOOH主要通过静电作用相结合,而在γ-Al2O3表面除了静电和氢键作用外,还存在通过铝与磷酸根中的氧配位形成的内层配合物;在3相似文献   

CuO-Ag2O/γ-Al2O3催化剂的TPR特性及氧化活性研究

采用程序升温还原技术(TPR)研究CuO-Ag2O/γ-Al2O3双组分及其单组分催化剂的还原特性以及热处理温度对其还原性能的影响。发现不同负载量的Cuo-Ag2O/γ-Al2O3催化剂的还原特性有明显差异, 反映出催化剂表面存在着不同种类的铜物种。Ag2O的存在, 使催化剂的TPR峰位与单组分CuO/γ-Al2O3的TPR曲线产生明显差异, 还原峰发生位移, 随Ag2O添加量的增加, 位移增大。对苯的完全氧化反应结果表明, 催化剂的氧化活性次序为:CuO-Ag2O/γ-Al2O3>CuO/γ-Al2O3>Ag2O/γ-Al2O3。热处理温度升高, 使催化剂表面铜物种分散状态及其还原性能发生变化。从500~900℃, 存在一个使铜物种达到最佳分散态的温度。讨论了负载于γ-Al2O3载体上的CuO-Ag2O双组分及其单组分催化剂在还原过程中金属与载体, 金属与金属间的相互作用以及热处理温度对其还原性能的影响。     

Kinetics and mechanism of oxidation of xylitol and galactitol by hexacyanoferrate(III) ion in aqueous alkaline medium

Kinetics of oxidation of xylitol and galactitol by hexacyanoferrate(III) ion in aqueous alkaline medium is reported. The reaction rate is of first order with respect to hexacyanoferrate(III) in each substrate. The reaction is first order at lower concentrations of xylitol and galactitol and tends towards zero order as the concentration increases. Similarly first order kinetics was obtained with respect to hydroxide ion at lower concentrations and tends to lower order at higher concentration in the oxidation of xylitol; in the oxidation of galactitol the reaction is first order with respect to hydroxide ion even up to manyfold variation. The course of reaction has been considered to proceed through the formation of an activated complex between [K Fe(CN)₆]^2– and substrate anion which decomposes slowly into radical and [K Fe(CN)₆]^3–. A probable reaction mechanism is proposed.

---

Kinetik und Mechanismus der Oxidation von Xylit und Galaktit mit Hexacyanoferrat(III) in wäßriger, alkalischer Lösung

Zusammenfassung Das Geschwindigkeitsgesetz der Titelreaktion ist in beiden Fällen erster Ordnung bezüglich Hexacyanoferrat(III). Die Oxidation ist erster Ordnung bei niedrigen Konzentrationen von Xylit und Galaktit und geht bei Erhöhung der Konzentration gegen null. In gleicher Weise wurde eine Kinetik erster Ordnung bezüglich Hydroxyl bei niedrigen Konzentrationen und eine erniedrigte Ordnung bei höheren Konzentrationen für die Oxidation von Xylit beobachtet; bei Galaktit bleibt die Oxidation auch bei höheren Hydroxyl-Konzentrationen erster Ordnung. Es wird angenommen, daß die Reaktion über einen aktivierten Komplex zwischen [KFe(CN)₆]^2– und dem Substrat-Anion verläuft; dieser Komplex zerfällt in [KFe(CN)₆]^3– und ein Substrat-Radikal. Ein möglicher Reaktionsmechanismus wird vorgeschlagen.

     

Pyrazoles as molecular probes to study the properties of co-crystals by solid state NMR spectroscopy

Equimolar mixtures of 3,5-dimethylpyrazole (1) with four NH-imidazoles (2–5) have been studied by¹³C and ¹⁵N CPMAS NMR and by DSC. In three cases, the solid mixture behaves as the sum of the individual components [imidazole (2), 2-methylimidazole (3) and 2,4(5)-dimethylimidazole (5)]. In one case [4,5-dimethylimidazole (4)], the mixture corresponds to a new species in which the dynamic behavior of1 no longer exists.     

Catalytic air oxidation of manganese in synthetic waters

An attempt was made to study the oxidation of manganese by air in synthetic waters. A series of batch experments were performed at differnet values of concentration, temperature and pH. Unoxidized manganese in the solution was determined by formaldoxime spectrometric method. Results of these studies indicated that the air oxidation of manganese soluble in water can be effectively performed in basic media and that oxidation yield increasedwith an increase in pH and concentration. The yield was very high in the presence of manganese dioxide, sepiolite or clinoptilolite in solution and, the oxidation was almost completed especially at high values of pH and concentration. The reaction was found to be first order with respect to Mn²⁺ with a very low activation energy. A yield of 62% was obtained for the air oxidation of wastewater taken from the treatment plant of Corum Municipality.     

Aqueous p-nitrotoluene oxidation induced with direct glow discharge plasma

A plasma induced degradation process has been studied to treat 4-nitrotoluene (4-NT) present as an aqueous pollutant. The plasma was locally generated from a glow discharge around a tip of a platinum anode in an electrolytic solution. The influence of initial pH and Fe²⁺ on the degradation was examined. Major intermediates resulting from the degradation process were identified. Amongst the aromatic intermediates, p-hydroxybenzoic acid was the predominant degradation product. The formation of oxalic acid, malic acid was also observed. The final products of degradation were NH ₄ ⁺ , NO ₃ ⁻ and CO₂. Based on the analysis of intermediates and the kinetic considerations, the degradation was shown to follow a pseudo-first order reaction hence, a possible reaction pathway was proposed.     

Zur Kenntnis der Reaktionsfähigkeit des Thiomorpholins und alkylsubstituierter Thiomorpholine, 4. Mitt.

Thiomorpholine as well as alkyl substituted thiomorpholines and their Sdioxides, respectively, are transformed into the corresponding N-Aminothiomorpholines by nitrosation (1–5) followed by the reduction with zinc in acetic acid/acetic acid anhydride under simultaneous formation of the corresponding N-acetyl derivates, and hydrolysis by hydrochloric acid (6–9). Examples of this method are described. 4-Aminothiomorpholines and their Sdioxides react with aldehydes or ketones to give azomethines (10–31). Acylation with mono-and dicarbonic acid chlorides leads to the N-acyl derivatives32–44.Mannich condensation is also possible. By oxidation with yellow mercury oxide tetracenes are formed (46–47).

Teil der DissertationM. Schmitz, Techn. Hochschule Aachen, 1975.     

Beiträge zur Chemie der Pyrrolpigmente, 40. Mitt.: Azafulvene,Schlüsselstellen beim Aufbau von Pyrrolpigmenten? —Eine neue Synthese von verdinoiden und rubinoiden Gallenfarbstoffen

Substituted azafulvenes were generated by dehydrogenation of 5-methyl-substituted pyrromethenones withDDQ and characterized by UV- and¹H-NMR-spectroscopy. Their electrophilic properties were demonstrated using several quenchers and furthermore they were used for a synthesis of verdinoid bile pigments (which easily can be converted to rubinoid systems by the action of NaBH₄) with nearly any desired unsymmetrical alkyl substitution patter: The azafulvene spezies was generated by the action ofDDQ on a 5-methylpyrromethenone and was quenched by an 5-unsubstituted pyrromethenone. The resulting rubinoid adduct was dehydrogenated immediatly byDDQ — yields were good to high.

39. Mitt.:Falk, H., Höllbacher, G., Hofer, O., Müller, N., Mh. Chem.112, 391 (1981).     

Potentiometric studies on the complex formation of lanthanides with proline and hydroxyproline

The formation of the lanthanide (La, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Lu) complexes with proline and hydroxyproline has been investigated by potentiometric methods as well as by a turbidimetric one which has provided some additional conclusions. It has been found that 11 and a slight amount of 21 complexes are formed. The deviation from the typical course of the formation function is discussed. It is suggested that the perturbations of complex formation in the systems are caused by hydrolysis. The stability constants of the complexes are reported.

---

Potentiometrische Untersuchungen an Lanthanid-Komplexen von Prolin und Hydroxyprolin

Zusammenfassung Die Bildung von Lanthanid-Komplexen (La, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Lu) mit Prolin und Hydroxyprolin wurde potentiometrisch und mit Hilfe von Trübungsmessungen untersucht. Es wurde festgestellt, daß sich Komplexe der Zusammensetzung 11 und in kleiner Menge auch 21 bilden. Die Abweichung von typischem Verlauf der Bildungskurven wurde untersucht. Es wurde dabei festgestellt, daß für die Störungen in der Komplexbildung die Hydrolyse verantwortlich ist. Die Stabilitätskonstanten wurden bestimmt.

     

A study of sample mineralization methods for arsenic analysis of blood and urine by hydride generation and graphite furnace atomic absorption spectrometry

Mineralization procedures for blood and urine suitable for the determination of arsenic by Hydride Generation Atomic Absorption Spectrometry (HGAAS) are studied on model samples, and the results are utilized in biological monitoring investigations. The objective of this work is to obtain good total As recoveries for both matrices regardless of added As species (As(III), As(V), DMA, MMA, AsB, or AsC). Prior to the HGAAS analyses, preparation procedures were controlled under optimised conditions by graphite furnace atomic absorption spectrometry (GFAAS). Two preparation procedures for urine give As recoveries close to 100% by HGAAS: a) dry ashing at 420°C with Mg(NO₃)₂ on a hot plate, and b) microwave oven decomposition with (NH₄)₂S₂O₈. For blood samples, As recoveries by HGAAS range between 95 and 108% for all species when using dry ashing after a pretreatment of samples with HNO₃ and H₂O₂ in a microwave oven. Wet digestion with (NH₄)₂S₂O₈ in a microwave oven gives recoveries very near 100% for As _inorg. and MMA. For other As species in spiked blood samples, recoveries of less than 20% As are found. Precision and detection limits obtained by both techniques are evaluated as well. For arsenic concentrations of 20 μg dm⁻³ or more in blood and urine, a chemical modifier is recommended for GFAAS analysis; it may or may not be proceeded by a mineralization step. For low As levels encountered in the unexposed population, the HGAAS technique provides reliable results only if a very complete mineralization procedure is used.     

Ein Beitrag zur Kristallchemie der Kobaltoxoniobate: CoNb2O6 mit Rutilstruktur

CoNb₂O₆ can be prepared by reaction of stoichiometric amounts of CoO (thermical decomposition of cobaltoxalate) and Nb₂O₅ in argon-atmosphere up to 1,400 °C. The isolated red-brown single crystals have tetragonal symmetry (a=472.6;c=305.4 pm; space group P4₂/mnm-D _4h ¹⁴ ). Electron probe micro-analysis of the single crystals verifies the composition Co_0.33Nb_0.67O₂. Co²⁺ and Nb⁵⁺ occupy statistically the metal positions of the rutil-type structure. The differences between Co_0.5Nb_0.5O₂ (CoNbO₄AlNbO₄-type) and Co_0.38Nb_0.67O₂ (CoNb₂O₆) are discussed.

     

Intermicellar material exchange in reverse micelles formed by ionic AOT and nonionic Igepal surfactants studied by means of pulse radiolysis. Influence of the temperature

The recombination of thiocyanate anion radicals, (SCN) ₂ ⁻ , formed pulse radiolytically within the water pools of reverse micelles stabilized with anionic AOT and nonionic Igepal surfactants, was proved as an indicator reaction to study intermicellar exchange. It was found that the exchange process is slower inIgepal than in AOT reverse micelles with the same water to surfactant ratio. The apparent activation enthalpy and entropy of the exchange process were determined in different alkanes. For the AOT and Igepal reverse micelles the activation parameters increase with the droplet size, but for the AOT systems they do not significantly change with the increase of droplet concentration. For non-percolated systems the activation parameters for Igepal reverse micelles approach those for AOT reverse micelles. This result supports existing suggestions that the mechanism of intermicellar exchange does not differ in principle between reverse micelles stabilized with ionic and nonionic surfactants.